Before this change the device tree description of qspi node for
second memory on BK4 board was wrong (applicable to old, removed
fsl-quadspi.c driver).
As a result this memory was not recognized correctly when used
with the new spi-fsl-qspi.c driver.
From the dt-bindings:
"Required SPI slave node properties:
- reg: There are two buses (A and B) with two chip selects each.
This encodes to which bus and CS the flash is connected:
<0>: Bus A, CS 0
<1>: Bus A, CS 1
<2>: Bus B, CS 0
<3>: Bus B, CS 1"
According to above with new driver the second SPI-NOR memory shall
have reg=<2> as it is connected to Bus B, CS 0.
Signed-off-by: Lukasz Majewski <[email protected]>
Suggested-by: Fabio Estevam <[email protected]>
Fixes: a67d2c52a82f ("ARM: dts: Add support for Liebherr's BK4 device
(vf610 based)")
---
Changes for v2:
- Add proper Suggested-by tag as Fabio was the one who pointed out the
the issue with wrong reg number assignment for the second SPI-NOR memory
- Add Fixes: tag, so the patch could be added to LTS kernels
- Fix the subject line to more appropriate
---
arch/arm/boot/dts/vf610-bk4.dts | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/vf610-bk4.dts b/arch/arm/boot/dts/vf610-bk4.dts
index 3fa0cbe456db..0f3870d3b099 100644
--- a/arch/arm/boot/dts/vf610-bk4.dts
+++ b/arch/arm/boot/dts/vf610-bk4.dts
@@ -246,13 +246,13 @@
reg = <0>;
};
- n25q128a13_2: flash@1 {
+ n25q128a13_2: flash@2 {
compatible = "n25q128a13", "jedec,spi-nor";
#address-cells = <1>;
#size-cells = <1>;
spi-max-frequency = <66000000>;
spi-rx-bus-width = <2>;
- reg = <1>;
+ reg = <2>;
};
};
--
2.11.0
Hi Lukasz,
On Tue, Jul 30, 2019 at 6:48 PM Lukasz Majewski <[email protected]> wrote:
>
> Before this change the device tree description of qspi node for
> second memory on BK4 board was wrong (applicable to old, removed
> fsl-quadspi.c driver).
>
> As a result this memory was not recognized correctly when used
> with the new spi-fsl-qspi.c driver.
>
> From the dt-bindings:
>
> "Required SPI slave node properties:
> - reg: There are two buses (A and B) with two chip selects each.
> This encodes to which bus and CS the flash is connected:
> <0>: Bus A, CS 0
> <1>: Bus A, CS 1
> <2>: Bus B, CS 0
> <3>: Bus B, CS 1"
>
> According to above with new driver the second SPI-NOR memory shall
> have reg=<2> as it is connected to Bus B, CS 0.
>
> Signed-off-by: Lukasz Majewski <[email protected]>
> Suggested-by: Fabio Estevam <[email protected]>
> Fixes: a67d2c52a82f ("ARM: dts: Add support for Liebherr's BK4 device
> (vf610 based)")
Please fix the order of the tags.
- Fixes tag goes first (do not split it into two lines)
- Suggested-by
- Your Signed-off-by
With these changes you can add as the last tag:
Reviewed-by: Fabio Estevam <[email protected]>