From: Kiran K <[email protected]>
1) add a helper function to download firmware
2) add a function to construct firmware / ddc file name
3) add a flag to identify new geneeration Intel controllers
4) define *setup* and hook it up for new genertion Intel controllers
5) map Typhoon Peak controller (PID:0x0032) to new generation controller
Signed-off-by: Kiran K <[email protected]>
Signed-off-by: Amit K Bag <[email protected]>
Signed-off-by: Raghuram Hegde <[email protected]>
Reviewed-by: Sathish Narasimman <[email protected]>
Reviewed-by: Chethan T N <[email protected]>
Reviewed-by: Srivatsa Ravishankar <[email protected]>
---
drivers/bluetooth/btintel.h | 6 +
drivers/bluetooth/btusb.c | 324 +++++++++++++++++++++++++++++++++++++++++++-
2 files changed, 328 insertions(+), 2 deletions(-)
diff --git a/drivers/bluetooth/btintel.h b/drivers/bluetooth/btintel.h
index 09346ae..c4e28a8 100644
--- a/drivers/bluetooth/btintel.h
+++ b/drivers/bluetooth/btintel.h
@@ -132,6 +132,12 @@ struct intel_debug_features {
__u8 page1[16];
} __packed;
+#define INTEL_HW_PLATFORM(cnvx_bt) ((u8)(((cnvx_bt) & 0x0000ff00) >> 8))
+#define INTEL_HW_VARIANT(cnvx_bt) ((u8)(((cnvx_bt) & 0x003f0000) >> 16))
+#define INTEL_CNVX_TOP_TYPE(cnvx_top) ((cnvx_top) & 0x00000fff)
+#define INTEL_CNVX_TOP_STEP(cnvx_top) (((cnvx_top) & 0x0f000000) >> 24)
+#define INTEL_CNVX_TOP_PACK_SWAB(t, s) __swab16(((__u16)(((t) << 4) | (s))))
+
#if IS_ENABLED(CONFIG_BT_INTEL)
int btintel_check_bdaddr(struct hci_dev *hdev);
diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 1005b6e..5e51749 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -60,6 +60,7 @@ static struct usb_driver btusb_driver;
#define BTUSB_WIDEBAND_SPEECH 0x400000
#define BTUSB_VALID_LE_STATES 0x800000
#define BTUSB_QCA_WCN6855 0x1000000
+#define BTUSB_INTEL_NEWGEN 0x2000000
static const struct usb_device_id btusb_table[] = {
/* Generic Bluetooth USB device */
@@ -365,7 +366,7 @@ static const struct usb_device_id blacklist_table[] = {
BTUSB_WIDEBAND_SPEECH },
{ USB_DEVICE(0x8087, 0x0029), .driver_info = BTUSB_INTEL_NEW |
BTUSB_WIDEBAND_SPEECH },
- { USB_DEVICE(0x8087, 0x0032), .driver_info = BTUSB_INTEL_NEW |
+ { USB_DEVICE(0x8087, 0x0032), .driver_info = BTUSB_INTEL_NEWGEN |
BTUSB_WIDEBAND_SPEECH},
{ USB_DEVICE(0x8087, 0x07da), .driver_info = BTUSB_CSR },
{ USB_DEVICE(0x8087, 0x07dc), .driver_info = BTUSB_INTEL },
@@ -2359,6 +2360,181 @@ static bool btusb_setup_intel_new_get_fw_name(struct intel_version *ver,
return true;
}
+static void btusb_setup_intel_newgen_get_fw_name(const struct intel_version_tlv *ver_tlv,
+ char *fw_name, size_t len,
+ const char *suffix)
+{
+ /* The firmware file name for new generation controllers will be
+ * ibt-<cnvi_top type+cnvi_top step>-<cnvr_top type+cnvr_top step>
+ */
+ snprintf(fw_name, len, "intel/ibt-%04x-%04x.%s",
+ INTEL_CNVX_TOP_PACK_SWAB(INTEL_CNVX_TOP_TYPE(ver_tlv->cnvi_top),
+ INTEL_CNVX_TOP_STEP(ver_tlv->cnvi_top)),
+ INTEL_CNVX_TOP_PACK_SWAB(INTEL_CNVX_TOP_TYPE(ver_tlv->cnvr_top),
+ INTEL_CNVX_TOP_STEP(ver_tlv->cnvr_top)),
+ suffix);
+}
+
+static int btusb_intel_download_firmware_newgen(struct hci_dev *hdev,
+ struct intel_version_tlv *ver,
+ u32 *boot_param)
+{
+ const struct firmware *fw;
+ char fwname[64];
+ int err;
+ struct btusb_data *data = hci_get_drvdata(hdev);
+
+ if (!ver || !boot_param)
+ return -EINVAL;
+
+ /* The hardware platform number has a fixed value of 0x37 and
+ * for now only accept this single value.
+ */
+ if (INTEL_HW_PLATFORM(ver->cnvi_bt) != 0x37) {
+ bt_dev_err(hdev, "Unsupported Intel hardware platform (0x%2x)",
+ INTEL_HW_PLATFORM(ver->cnvi_bt));
+ return -EINVAL;
+ }
+
+ /* The firmware variant determines if the device is in bootloader
+ * mode or is running operational firmware. The value 0x03 identifies
+ * the bootloader and the value 0x23 identifies the operational
+ * firmware.
+ *
+ * When the operational firmware is already present, then only
+ * the check for valid Bluetooth device address is needed. This
+ * determines if the device will be added as configured or
+ * unconfigured controller.
+ *
+ * It is not possible to use the Secure Boot Parameters in this
+ * case since that command is only available in bootloader mode.
+ */
+ if (ver->img_type == 0x03) {
+ clear_bit(BTUSB_BOOTLOADER, &data->flags);
+ btintel_check_bdaddr(hdev);
+ return 0;
+ }
+
+ /* Check for supported iBT hardware variants of this firmware
+ * loading method.
+ *
+ * This check has been put in place to ensure correct forward
+ * compatibility options when newer hardware variants come along.
+ */
+ switch (INTEL_HW_VARIANT(ver->cnvi_bt)) {
+ case 0x17: /* TyP */
+ case 0x18: /* Slr */
+ case 0x19: /* Slr-F */
+ break;
+ default:
+ bt_dev_err(hdev, "Unsupported Intel hardware variant (0x%x)",
+ INTEL_HW_VARIANT(ver->cnvi_bt));
+ return -EINVAL;
+ }
+
+ /* If the device is not in bootloader mode, then the only possible
+ * choice is to return an error and abort the device initialization.
+ */
+ if (ver->img_type != 0x01) {
+ bt_dev_err(hdev, "Unsupported Intel firmware variant (0x%x)",
+ ver->img_type);
+ return -ENODEV;
+ }
+
+ /* It is required that every single firmware fragment is acknowledged
+ * with a command complete event. If the boot parameters indicate
+ * that this bootloader does not send them, then abort the setup.
+ */
+ if (ver->limited_cce != 0x00) {
+ bt_dev_err(hdev, "Unsupported Intel firmware loading method (0x%x)",
+ ver->limited_cce);
+ return -EINVAL;
+ }
+
+ /* Secure boot engine type should be either 1 (ECDSA) or 0 (RSA) */
+ if (ver->sbe_type > 0x01) {
+ bt_dev_err(hdev, "Unsupported Intel secure boot engine type (0x%x)",
+ ver->sbe_type);
+ return -EINVAL;
+ }
+
+ /* If the OTP has no valid Bluetooth device address, then there will
+ * also be no valid address for the operational firmware.
+ */
+ if (!bacmp(&ver->otp_bd_addr, BDADDR_ANY)) {
+ bt_dev_info(hdev, "No device address configured");
+ set_bit(HCI_QUIRK_INVALID_BDADDR, &hdev->quirks);
+ }
+
+ btusb_setup_intel_newgen_get_fw_name(ver, fwname, sizeof(fwname), "sfi");
+ err = request_firmware(&fw, fwname, &hdev->dev);
+ if (err < 0) {
+ bt_dev_err(hdev, "Failed to load Intel firmware file (%d)", err);
+ return err;
+ }
+
+ bt_dev_info(hdev, "Found device firmware: %s", fwname);
+
+ if (fw->size < 644) {
+ bt_dev_err(hdev, "Invalid size of firmware file (%zu)",
+ fw->size);
+ err = -EBADF;
+ goto done;
+ }
+
+ set_bit(BTUSB_DOWNLOADING, &data->flags);
+
+ /* Start firmware downloading and get boot parameter */
+ err = btintel_download_firmware_newgen(hdev, fw, boot_param,
+ INTEL_HW_VARIANT(ver->cnvi_bt),
+ ver->sbe_type);
+ if (err < 0) {
+ /* When FW download fails, send Intel Reset to retry
+ * FW download.
+ */
+ btintel_reset_to_bootloader(hdev);
+ goto done;
+ }
+ set_bit(BTUSB_FIRMWARE_LOADED, &data->flags);
+
+ bt_dev_info(hdev, "Waiting for firmware download to complete");
+
+ /* Before switching the device into operational mode and with that
+ * booting the loaded firmware, wait for the bootloader notification
+ * that all fragments have been successfully received.
+ *
+ * When the event processing receives the notification, then the
+ * BTUSB_DOWNLOADING flag will be cleared.
+ *
+ * The firmware loading should not take longer than 5 seconds
+ * and thus just timeout if that happens and fail the setup
+ * of this device.
+ */
+ err = wait_on_bit_timeout(&data->flags, BTUSB_DOWNLOADING,
+ TASK_INTERRUPTIBLE,
+ msecs_to_jiffies(5000));
+ if (err == -EINTR) {
+ bt_dev_err(hdev, "Firmware loading interrupted");
+ goto done;
+ }
+
+ if (err) {
+ bt_dev_err(hdev, "Firmware loading timeout");
+ err = -ETIMEDOUT;
+ btintel_reset_to_bootloader(hdev);
+ goto done;
+ }
+
+ if (test_bit(BTUSB_FIRMWARE_FAILED, &data->flags)) {
+ bt_dev_err(hdev, "Firmware loading failed");
+ err = -ENOEXEC;
+ goto done;
+ }
+
+done:
+ release_firmware(fw);
+ return err;
+}
static int btusb_intel_download_firmware(struct hci_dev *hdev,
struct intel_version *ver,
struct intel_boot_params *params,
@@ -2693,6 +2869,135 @@ static int btusb_setup_intel_new(struct hci_dev *hdev)
return 0;
}
+static int btusb_setup_intel_newgen(struct hci_dev *hdev)
+{
+ struct btusb_data *data = hci_get_drvdata(hdev);
+ u32 boot_param;
+ char ddcname[64];
+ ktime_t calltime, delta, rettime;
+ unsigned long long duration;
+ int err;
+ struct intel_debug_features features;
+ struct intel_version_tlv version;
+
+ BT_DBG("%s", hdev->name);
+
+ /* Set the default boot parameter to 0x0 and it is updated to
+ * SKU specific boot parameter after reading Intel_Write_Boot_Params
+ * command while downloading the firmware.
+ */
+ boot_param = 0x00000000;
+
+ calltime = ktime_get();
+
+ /* Read the Intel version information to determine if the device
+ * is in bootloader mode or if it already has operational firmware
+ * loaded.
+ */
+ err = btintel_read_version_tlv(hdev, &version);
+ if (err) {
+ bt_dev_err(hdev, "Intel Read version failed (%d)", err);
+ btintel_reset_to_bootloader(hdev);
+ return err;
+ }
+
+ btintel_version_info_tlv(hdev, &version);
+
+ err = btusb_intel_download_firmware_newgen(hdev, &version, &boot_param);
+ if (err)
+ return err;
+
+ /* check if controller is already having an operational firmware */
+ if (version.img_type == 0x03)
+ goto finish;
+
+ rettime = ktime_get();
+ delta = ktime_sub(rettime, calltime);
+ duration = (unsigned long long)ktime_to_ns(delta) >> 10;
+
+ bt_dev_info(hdev, "Firmware loaded in %llu usecs", duration);
+
+ calltime = ktime_get();
+
+ set_bit(BTUSB_BOOTING, &data->flags);
+
+ err = btintel_send_intel_reset(hdev, boot_param);
+ if (err) {
+ bt_dev_err(hdev, "Intel Soft Reset failed (%d)", err);
+ btintel_reset_to_bootloader(hdev);
+ return err;
+ }
+
+ /* The bootloader will not indicate when the device is ready. This
+ * is done by the operational firmware sending bootup notification.
+ *
+ * Booting into operational firmware should not take longer than
+ * 1 second. However if that happens, then just fail the setup
+ * since something went wrong.
+ */
+ bt_dev_info(hdev, "Waiting for device to boot");
+
+ err = wait_on_bit_timeout(&data->flags, BTUSB_BOOTING,
+ TASK_INTERRUPTIBLE,
+ msecs_to_jiffies(1000));
+
+ if (err == -EINTR) {
+ bt_dev_err(hdev, "Device boot interrupted");
+ return -EINTR;
+ }
+
+ if (err) {
+ bt_dev_err(hdev, "Device boot timeout");
+ btintel_reset_to_bootloader(hdev);
+ return -ETIMEDOUT;
+ }
+
+ rettime = ktime_get();
+ delta = ktime_sub(rettime, calltime);
+ duration = (unsigned long long)ktime_to_ns(delta) >> 10;
+
+ bt_dev_info(hdev, "Device booted in %llu usecs", duration);
+
+ clear_bit(BTUSB_BOOTLOADER, &data->flags);
+
+ btusb_setup_intel_newgen_get_fw_name(&version, ddcname, sizeof(ddcname),
+ "ddc");
+
+ /* Once the device is running in operational mode, it needs to
+ * apply the device configuration (DDC) parameters.
+ *
+ * The device can work without DDC parameters, so even if it
+ * fails to load the file, no need to fail the setup.
+ */
+ btintel_load_ddc_config(hdev, ddcname);
+
+ /* Read the Intel supported features and if new exception formats
+ * supported, need to load the additional DDC config to enable.
+ */
+ btintel_read_debug_features(hdev, &features);
+
+ /* Set DDC mask for available debug features */
+ btintel_set_debug_features(hdev, &features);
+
+ /* Read the Intel version information after loading the FW */
+ err = btintel_read_version_tlv(hdev, &version);
+ if (err)
+ return err;
+
+ btintel_version_info_tlv(hdev, &version);
+
+finish:
+ /* Set the event mask for Intel specific vendor events. This enables
+ * a few extra events that are useful during general operation. It
+ * does not enable any debugging related events.
+ *
+ * The device will function correctly without these events enabled
+ * and thus no need to fail the setup.
+ */
+ btintel_set_event_mask(hdev, false);
+
+ return 0;
+}
static int btusb_shutdown_intel(struct hci_dev *hdev)
{
struct sk_buff *skb;
@@ -3969,7 +4274,8 @@ static int btusb_probe(struct usb_interface *intf,
init_usb_anchor(&data->ctrl_anchor);
spin_lock_init(&data->rxlock);
- if (id->driver_info & BTUSB_INTEL_NEW) {
+ if ((id->driver_info & BTUSB_INTEL_NEW) ||
+ (id->driver_info & BTUSB_INTEL_NEWGEN)) {
data->recv_event = btusb_recv_event_intel;
data->recv_bulk = btusb_recv_bulk_intel;
set_bit(BTUSB_BOOTLOADER, &data->flags);
@@ -4078,6 +4384,20 @@ static int btusb_probe(struct usb_interface *intf,
set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
}
+ if (id->driver_info & BTUSB_INTEL_NEWGEN) {
+ hdev->manufacturer = 2;
+ hdev->send = btusb_send_frame_intel;
+ hdev->setup = btusb_setup_intel_newgen;
+ hdev->shutdown = btusb_shutdown_intel_new;
+ hdev->hw_error = btintel_hw_error;
+ hdev->set_diag = btintel_set_diag;
+ hdev->set_bdaddr = btintel_set_bdaddr;
+ hdev->cmd_timeout = btusb_intel_cmd_timeout;
+ set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
+ set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
+ set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
+ }
+
if (id->driver_info & BTUSB_MARVELL)
hdev->set_bdaddr = btusb_set_bdaddr_marvell;
--
2.7.4
Hi Kiran,
On Thu, Oct 1, 2020 at 11:58 PM Kiran K <[email protected]> wrote:
>
> From: Kiran K <[email protected]>
>
> 1) add a helper function to download firmware
>
> 2) add a function to construct firmware / ddc file name
>
> 3) add a flag to identify new geneeration Intel controllers
>
> 4) define *setup* and hook it up for new genertion Intel controllers
>
> 5) map Typhoon Peak controller (PID:0x0032) to new generation controller
Instead of enumerating the changes here it would probably make more
sense to have them as separate patches.
> Signed-off-by: Kiran K <[email protected]>
> Signed-off-by: Amit K Bag <[email protected]>
> Signed-off-by: Raghuram Hegde <[email protected]>
> Reviewed-by: Sathish Narasimman <[email protected]>
> Reviewed-by: Chethan T N <[email protected]>
> Reviewed-by: Srivatsa Ravishankar <[email protected]>
> ---
> drivers/bluetooth/btintel.h | 6 +
> drivers/bluetooth/btusb.c | 324 +++++++++++++++++++++++++++++++++++++++++++-
> 2 files changed, 328 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/bluetooth/btintel.h b/drivers/bluetooth/btintel.h
> index 09346ae..c4e28a8 100644
> --- a/drivers/bluetooth/btintel.h
> +++ b/drivers/bluetooth/btintel.h
> @@ -132,6 +132,12 @@ struct intel_debug_features {
> __u8 page1[16];
> } __packed;
>
> +#define INTEL_HW_PLATFORM(cnvx_bt) ((u8)(((cnvx_bt) & 0x0000ff00) >> 8))
> +#define INTEL_HW_VARIANT(cnvx_bt) ((u8)(((cnvx_bt) & 0x003f0000) >> 16))
> +#define INTEL_CNVX_TOP_TYPE(cnvx_top) ((cnvx_top) & 0x00000fff)
> +#define INTEL_CNVX_TOP_STEP(cnvx_top) (((cnvx_top) & 0x0f000000) >> 24)
> +#define INTEL_CNVX_TOP_PACK_SWAB(t, s) __swab16(((__u16)(((t) << 4) | (s))))
> +
> #if IS_ENABLED(CONFIG_BT_INTEL)
>
> int btintel_check_bdaddr(struct hci_dev *hdev);
> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
> index 1005b6e..5e51749 100644
> --- a/drivers/bluetooth/btusb.c
> +++ b/drivers/bluetooth/btusb.c
> @@ -60,6 +60,7 @@ static struct usb_driver btusb_driver;
> #define BTUSB_WIDEBAND_SPEECH 0x400000
> #define BTUSB_VALID_LE_STATES 0x800000
> #define BTUSB_QCA_WCN6855 0x1000000
> +#define BTUSB_INTEL_NEWGEN 0x2000000
I wonder if it is a good idea to keep adding such flags per model
here, it should be possible to pass the pid/vid so we don't have to
add generation after generation here.
>
> static const struct usb_device_id btusb_table[] = {
> /* Generic Bluetooth USB device */
> @@ -365,7 +366,7 @@ static const struct usb_device_id blacklist_table[] = {
> BTUSB_WIDEBAND_SPEECH },
> { USB_DEVICE(0x8087, 0x0029), .driver_info = BTUSB_INTEL_NEW |
> BTUSB_WIDEBAND_SPEECH },
> - { USB_DEVICE(0x8087, 0x0032), .driver_info = BTUSB_INTEL_NEW |
> + { USB_DEVICE(0x8087, 0x0032), .driver_info = BTUSB_INTEL_NEWGEN |
> BTUSB_WIDEBAND_SPEECH},
> { USB_DEVICE(0x8087, 0x07da), .driver_info = BTUSB_CSR },
> { USB_DEVICE(0x8087, 0x07dc), .driver_info = BTUSB_INTEL },
> @@ -2359,6 +2360,181 @@ static bool btusb_setup_intel_new_get_fw_name(struct intel_version *ver,
> return true;
> }
>
> +static void btusb_setup_intel_newgen_get_fw_name(const struct intel_version_tlv *ver_tlv,
> + char *fw_name, size_t len,
> + const char *suffix)
> +{
> + /* The firmware file name for new generation controllers will be
> + * ibt-<cnvi_top type+cnvi_top step>-<cnvr_top type+cnvr_top step>
> + */
> + snprintf(fw_name, len, "intel/ibt-%04x-%04x.%s",
> + INTEL_CNVX_TOP_PACK_SWAB(INTEL_CNVX_TOP_TYPE(ver_tlv->cnvi_top),
> + INTEL_CNVX_TOP_STEP(ver_tlv->cnvi_top)),
> + INTEL_CNVX_TOP_PACK_SWAB(INTEL_CNVX_TOP_TYPE(ver_tlv->cnvr_top),
> + INTEL_CNVX_TOP_STEP(ver_tlv->cnvr_top)),
> + suffix);
> +}
> +
> +static int btusb_intel_download_firmware_newgen(struct hci_dev *hdev,
> + struct intel_version_tlv *ver,
> + u32 *boot_param)
> +{
> + const struct firmware *fw;
> + char fwname[64];
> + int err;
> + struct btusb_data *data = hci_get_drvdata(hdev);
> +
> + if (!ver || !boot_param)
> + return -EINVAL;
> +
> + /* The hardware platform number has a fixed value of 0x37 and
> + * for now only accept this single value.
> + */
> + if (INTEL_HW_PLATFORM(ver->cnvi_bt) != 0x37) {
> + bt_dev_err(hdev, "Unsupported Intel hardware platform (0x%2x)",
> + INTEL_HW_PLATFORM(ver->cnvi_bt));
> + return -EINVAL;
> + }
> +
> + /* The firmware variant determines if the device is in bootloader
> + * mode or is running operational firmware. The value 0x03 identifies
> + * the bootloader and the value 0x23 identifies the operational
> + * firmware.
> + *
> + * When the operational firmware is already present, then only
> + * the check for valid Bluetooth device address is needed. This
> + * determines if the device will be added as configured or
> + * unconfigured controller.
> + *
> + * It is not possible to use the Secure Boot Parameters in this
> + * case since that command is only available in bootloader mode.
> + */
> + if (ver->img_type == 0x03) {
> + clear_bit(BTUSB_BOOTLOADER, &data->flags);
> + btintel_check_bdaddr(hdev);
> + return 0;
> + }
> +
> + /* Check for supported iBT hardware variants of this firmware
> + * loading method.
> + *
> + * This check has been put in place to ensure correct forward
> + * compatibility options when newer hardware variants come along.
> + */
> + switch (INTEL_HW_VARIANT(ver->cnvi_bt)) {
> + case 0x17: /* TyP */
> + case 0x18: /* Slr */
> + case 0x19: /* Slr-F */
> + break;
> + default:
> + bt_dev_err(hdev, "Unsupported Intel hardware variant (0x%x)",
> + INTEL_HW_VARIANT(ver->cnvi_bt));
> + return -EINVAL;
> + }
> +
> + /* If the device is not in bootloader mode, then the only possible
> + * choice is to return an error and abort the device initialization.
> + */
> + if (ver->img_type != 0x01) {
> + bt_dev_err(hdev, "Unsupported Intel firmware variant (0x%x)",
> + ver->img_type);
> + return -ENODEV;
> + }
> +
> + /* It is required that every single firmware fragment is acknowledged
> + * with a command complete event. If the boot parameters indicate
> + * that this bootloader does not send them, then abort the setup.
> + */
> + if (ver->limited_cce != 0x00) {
> + bt_dev_err(hdev, "Unsupported Intel firmware loading method (0x%x)",
> + ver->limited_cce);
> + return -EINVAL;
> + }
> +
> + /* Secure boot engine type should be either 1 (ECDSA) or 0 (RSA) */
> + if (ver->sbe_type > 0x01) {
> + bt_dev_err(hdev, "Unsupported Intel secure boot engine type (0x%x)",
> + ver->sbe_type);
> + return -EINVAL;
> + }
> +
> + /* If the OTP has no valid Bluetooth device address, then there will
> + * also be no valid address for the operational firmware.
> + */
> + if (!bacmp(&ver->otp_bd_addr, BDADDR_ANY)) {
> + bt_dev_info(hdev, "No device address configured");
> + set_bit(HCI_QUIRK_INVALID_BDADDR, &hdev->quirks);
> + }
> +
> + btusb_setup_intel_newgen_get_fw_name(ver, fwname, sizeof(fwname), "sfi");
> + err = request_firmware(&fw, fwname, &hdev->dev);
> + if (err < 0) {
> + bt_dev_err(hdev, "Failed to load Intel firmware file (%d)", err);
> + return err;
> + }
> +
> + bt_dev_info(hdev, "Found device firmware: %s", fwname);
> +
> + if (fw->size < 644) {
> + bt_dev_err(hdev, "Invalid size of firmware file (%zu)",
> + fw->size);
> + err = -EBADF;
> + goto done;
> + }
> +
> + set_bit(BTUSB_DOWNLOADING, &data->flags);
> +
> + /* Start firmware downloading and get boot parameter */
> + err = btintel_download_firmware_newgen(hdev, fw, boot_param,
> + INTEL_HW_VARIANT(ver->cnvi_bt),
> + ver->sbe_type);
> + if (err < 0) {
> + /* When FW download fails, send Intel Reset to retry
> + * FW download.
> + */
> + btintel_reset_to_bootloader(hdev);
> + goto done;
> + }
> + set_bit(BTUSB_FIRMWARE_LOADED, &data->flags);
> +
> + bt_dev_info(hdev, "Waiting for firmware download to complete");
> +
> + /* Before switching the device into operational mode and with that
> + * booting the loaded firmware, wait for the bootloader notification
> + * that all fragments have been successfully received.
> + *
> + * When the event processing receives the notification, then the
> + * BTUSB_DOWNLOADING flag will be cleared.
> + *
> + * The firmware loading should not take longer than 5 seconds
> + * and thus just timeout if that happens and fail the setup
> + * of this device.
> + */
> + err = wait_on_bit_timeout(&data->flags, BTUSB_DOWNLOADING,
> + TASK_INTERRUPTIBLE,
> + msecs_to_jiffies(5000));
> + if (err == -EINTR) {
> + bt_dev_err(hdev, "Firmware loading interrupted");
> + goto done;
> + }
> +
> + if (err) {
> + bt_dev_err(hdev, "Firmware loading timeout");
> + err = -ETIMEDOUT;
> + btintel_reset_to_bootloader(hdev);
> + goto done;
> + }
> +
> + if (test_bit(BTUSB_FIRMWARE_FAILED, &data->flags)) {
> + bt_dev_err(hdev, "Firmware loading failed");
> + err = -ENOEXEC;
> + goto done;
> + }
> +
> +done:
> + release_firmware(fw);
> + return err;
> +}
> static int btusb_intel_download_firmware(struct hci_dev *hdev,
> struct intel_version *ver,
> struct intel_boot_params *params,
> @@ -2693,6 +2869,135 @@ static int btusb_setup_intel_new(struct hci_dev *hdev)
> return 0;
> }
>
> +static int btusb_setup_intel_newgen(struct hci_dev *hdev)
> +{
> + struct btusb_data *data = hci_get_drvdata(hdev);
> + u32 boot_param;
> + char ddcname[64];
> + ktime_t calltime, delta, rettime;
> + unsigned long long duration;
> + int err;
> + struct intel_debug_features features;
> + struct intel_version_tlv version;
> +
> + BT_DBG("%s", hdev->name);
> +
> + /* Set the default boot parameter to 0x0 and it is updated to
> + * SKU specific boot parameter after reading Intel_Write_Boot_Params
> + * command while downloading the firmware.
> + */
> + boot_param = 0x00000000;
> +
> + calltime = ktime_get();
> +
> + /* Read the Intel version information to determine if the device
> + * is in bootloader mode or if it already has operational firmware
> + * loaded.
> + */
> + err = btintel_read_version_tlv(hdev, &version);
> + if (err) {
> + bt_dev_err(hdev, "Intel Read version failed (%d)", err);
> + btintel_reset_to_bootloader(hdev);
> + return err;
> + }
> +
> + btintel_version_info_tlv(hdev, &version);
> +
> + err = btusb_intel_download_firmware_newgen(hdev, &version, &boot_param);
> + if (err)
> + return err;
> +
> + /* check if controller is already having an operational firmware */
> + if (version.img_type == 0x03)
> + goto finish;
> +
> + rettime = ktime_get();
> + delta = ktime_sub(rettime, calltime);
> + duration = (unsigned long long)ktime_to_ns(delta) >> 10;
> +
> + bt_dev_info(hdev, "Firmware loaded in %llu usecs", duration);
> +
> + calltime = ktime_get();
> +
> + set_bit(BTUSB_BOOTING, &data->flags);
> +
> + err = btintel_send_intel_reset(hdev, boot_param);
> + if (err) {
> + bt_dev_err(hdev, "Intel Soft Reset failed (%d)", err);
> + btintel_reset_to_bootloader(hdev);
> + return err;
> + }
> +
> + /* The bootloader will not indicate when the device is ready. This
> + * is done by the operational firmware sending bootup notification.
> + *
> + * Booting into operational firmware should not take longer than
> + * 1 second. However if that happens, then just fail the setup
> + * since something went wrong.
> + */
> + bt_dev_info(hdev, "Waiting for device to boot");
> +
> + err = wait_on_bit_timeout(&data->flags, BTUSB_BOOTING,
> + TASK_INTERRUPTIBLE,
> + msecs_to_jiffies(1000));
> +
> + if (err == -EINTR) {
> + bt_dev_err(hdev, "Device boot interrupted");
> + return -EINTR;
> + }
> +
> + if (err) {
> + bt_dev_err(hdev, "Device boot timeout");
> + btintel_reset_to_bootloader(hdev);
> + return -ETIMEDOUT;
> + }
> +
> + rettime = ktime_get();
> + delta = ktime_sub(rettime, calltime);
> + duration = (unsigned long long)ktime_to_ns(delta) >> 10;
> +
> + bt_dev_info(hdev, "Device booted in %llu usecs", duration);
> +
> + clear_bit(BTUSB_BOOTLOADER, &data->flags);
> +
> + btusb_setup_intel_newgen_get_fw_name(&version, ddcname, sizeof(ddcname),
> + "ddc");
> +
> + /* Once the device is running in operational mode, it needs to
> + * apply the device configuration (DDC) parameters.
> + *
> + * The device can work without DDC parameters, so even if it
> + * fails to load the file, no need to fail the setup.
> + */
> + btintel_load_ddc_config(hdev, ddcname);
> +
> + /* Read the Intel supported features and if new exception formats
> + * supported, need to load the additional DDC config to enable.
> + */
> + btintel_read_debug_features(hdev, &features);
> +
> + /* Set DDC mask for available debug features */
> + btintel_set_debug_features(hdev, &features);
> +
> + /* Read the Intel version information after loading the FW */
> + err = btintel_read_version_tlv(hdev, &version);
> + if (err)
> + return err;
> +
> + btintel_version_info_tlv(hdev, &version);
> +
> +finish:
> + /* Set the event mask for Intel specific vendor events. This enables
> + * a few extra events that are useful during general operation. It
> + * does not enable any debugging related events.
> + *
> + * The device will function correctly without these events enabled
> + * and thus no need to fail the setup.
> + */
> + btintel_set_event_mask(hdev, false);
> +
> + return 0;
> +}
> static int btusb_shutdown_intel(struct hci_dev *hdev)
> {
> struct sk_buff *skb;
> @@ -3969,7 +4274,8 @@ static int btusb_probe(struct usb_interface *intf,
> init_usb_anchor(&data->ctrl_anchor);
> spin_lock_init(&data->rxlock);
>
> - if (id->driver_info & BTUSB_INTEL_NEW) {
> + if ((id->driver_info & BTUSB_INTEL_NEW) ||
> + (id->driver_info & BTUSB_INTEL_NEWGEN)) {
> data->recv_event = btusb_recv_event_intel;
> data->recv_bulk = btusb_recv_bulk_intel;
> set_bit(BTUSB_BOOTLOADER, &data->flags);
> @@ -4078,6 +4384,20 @@ static int btusb_probe(struct usb_interface *intf,
> set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
> }
>
> + if (id->driver_info & BTUSB_INTEL_NEWGEN) {
> + hdev->manufacturer = 2;
> + hdev->send = btusb_send_frame_intel;
> + hdev->setup = btusb_setup_intel_newgen;
> + hdev->shutdown = btusb_shutdown_intel_new;
> + hdev->hw_error = btintel_hw_error;
> + hdev->set_diag = btintel_set_diag;
> + hdev->set_bdaddr = btintel_set_bdaddr;
> + hdev->cmd_timeout = btusb_intel_cmd_timeout;
> + set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
> + set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
> + set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
> + }
> +
> if (id->driver_info & BTUSB_MARVELL)
> hdev->set_bdaddr = btusb_set_bdaddr_marvell;
>
> --
> 2.7.4
>
--
Luiz Augusto von Dentz
Hi Luiz,
>> Signed-off-by: Kiran K <[email protected]>
>> Signed-off-by: Amit K Bag <[email protected]>
>> Signed-off-by: Raghuram Hegde <[email protected]>
>> Reviewed-by: Sathish Narasimman <[email protected]>
>> Reviewed-by: Chethan T N <[email protected]>
>> Reviewed-by: Srivatsa Ravishankar <[email protected]>
>> ---
>> drivers/bluetooth/btintel.h | 6 +
>> drivers/bluetooth/btusb.c | 324 +++++++++++++++++++++++++++++++++++++++++++-
>> 2 files changed, 328 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/bluetooth/btintel.h b/drivers/bluetooth/btintel.h
>> index 09346ae..c4e28a8 100644
>> --- a/drivers/bluetooth/btintel.h
>> +++ b/drivers/bluetooth/btintel.h
>> @@ -132,6 +132,12 @@ struct intel_debug_features {
>> __u8 page1[16];
>> } __packed;
>>
>> +#define INTEL_HW_PLATFORM(cnvx_bt) ((u8)(((cnvx_bt) & 0x0000ff00) >> 8))
>> +#define INTEL_HW_VARIANT(cnvx_bt) ((u8)(((cnvx_bt) & 0x003f0000) >> 16))
>> +#define INTEL_CNVX_TOP_TYPE(cnvx_top) ((cnvx_top) & 0x00000fff)
>> +#define INTEL_CNVX_TOP_STEP(cnvx_top) (((cnvx_top) & 0x0f000000) >> 24)
>> +#define INTEL_CNVX_TOP_PACK_SWAB(t, s) __swab16(((__u16)(((t) << 4) | (s))))
>> +
>> #if IS_ENABLED(CONFIG_BT_INTEL)
>>
>> int btintel_check_bdaddr(struct hci_dev *hdev);
>> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
>> index 1005b6e..5e51749 100644
>> --- a/drivers/bluetooth/btusb.c
>> +++ b/drivers/bluetooth/btusb.c
>> @@ -60,6 +60,7 @@ static struct usb_driver btusb_driver;
>> #define BTUSB_WIDEBAND_SPEECH 0x400000
>> #define BTUSB_VALID_LE_STATES 0x800000
>> #define BTUSB_QCA_WCN6855 0x1000000
>> +#define BTUSB_INTEL_NEWGEN 0x2000000
>
> I wonder if it is a good idea to keep adding such flags per model
> here, it should be possible to pass the pid/vid so we don't have to
> add generation after generation here.
We agreed to first add the next gen controller as an independent setup method. And then later combine them into a single one that detects what version it is. We also need to unify it with our first generation ROM products.
Regards
Marcel
Hi Marcel, Luiz,
> -----Original Message-----
> From: Marcel Holtmann <[email protected]>
> Sent: Saturday, October 3, 2020 12:12 PM
> To: Luiz Augusto von Dentz <[email protected]>
> Cc: Kiran K <[email protected]>; [email protected];
> Narasimman, Sathish <[email protected]>; Tumkur Narayan,
> Chethan <[email protected]>; Srivatsa, Ravishankar
> <[email protected]>; K, Kiran <[email protected]>; Bag, Amit K
> <[email protected]>; Raghuram Hegde <[email protected]>
> Subject: Re: [PATCH v4] Bluetooth: btintel: Add *setup* function for new
> generation Intel controllers
>
> Hi Luiz,
>
> >> Signed-off-by: Kiran K <[email protected]>
> >> Signed-off-by: Amit K Bag <[email protected]>
> >> Signed-off-by: Raghuram Hegde <[email protected]>
> >> Reviewed-by: Sathish Narasimman <[email protected]>
> >> Reviewed-by: Chethan T N <[email protected]>
> >> Reviewed-by: Srivatsa Ravishankar <[email protected]>
> >> ---
> >> drivers/bluetooth/btintel.h | 6 +
> >> drivers/bluetooth/btusb.c | 324
> +++++++++++++++++++++++++++++++++++++++++++-
> >> 2 files changed, 328 insertions(+), 2 deletions(-)
> >>
> >> diff --git a/drivers/bluetooth/btintel.h
> >> b/drivers/bluetooth/btintel.h index 09346ae..c4e28a8 100644
> >> --- a/drivers/bluetooth/btintel.h
> >> +++ b/drivers/bluetooth/btintel.h
> >> @@ -132,6 +132,12 @@ struct intel_debug_features {
> >> __u8 page1[16];
> >> } __packed;
> >>
> >> +#define INTEL_HW_PLATFORM(cnvx_bt) ((u8)(((cnvx_bt) & 0x0000ff00)
> >> 8))
> >> +#define INTEL_HW_VARIANT(cnvx_bt) ((u8)(((cnvx_bt) & 0x003f0000)
> >> 16))
> >> +#define INTEL_CNVX_TOP_TYPE(cnvx_top) ((cnvx_top) & 0x00000fff)
> >> +#define INTEL_CNVX_TOP_STEP(cnvx_top) (((cnvx_top) & 0x0f000000)
> >>
> >> +24) #define INTEL_CNVX_TOP_PACK_SWAB(t, s) __swab16(((__u16)(((t)
> <<
> >> +4) | (s))))
> >> +
> >> #if IS_ENABLED(CONFIG_BT_INTEL)
> >>
> >> int btintel_check_bdaddr(struct hci_dev *hdev); diff --git
> >> a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index
> >> 1005b6e..5e51749 100644
> >> --- a/drivers/bluetooth/btusb.c
> >> +++ b/drivers/bluetooth/btusb.c
> >> @@ -60,6 +60,7 @@ static struct usb_driver btusb_driver; #define
> >> BTUSB_WIDEBAND_SPEECH 0x400000
> >> #define BTUSB_VALID_LE_STATES 0x800000
> >> #define BTUSB_QCA_WCN6855 0x1000000
> >> +#define BTUSB_INTEL_NEWGEN 0x2000000
> >
> > I wonder if it is a good idea to keep adding such flags per model
> > here, it should be possible to pass the pid/vid so we don't have to
> > add generation after generation here.
>
> We agreed to first add the next gen controller as an independent setup
> method. And then later combine them into a single one that detects what
> version it is. We also need to unify it with our first generation ROM products.
We can still have an independent setup function for next gen controllers. Only the method to identify the controller type is changed to use PID/VID instead of BTUSB_INTEL_NEW. I will submit the refined patch in V5. Please review it. If you still feel that we need to use BTUSB_INTEL_NEW, I will revert to v4.
>
> Regards
>
> Marcel
Thanks,
Kiran
Hi Luiz,
> -----Original Message-----
> From: Luiz Augusto von Dentz <[email protected]>
> Sent: Friday, October 2, 2020 11:32 PM
> To: Kiran K <[email protected]>
> Cc: [email protected]; Narasimman, Sathish
> <[email protected]>; Tumkur Narayan, Chethan
> <[email protected]>; Srivatsa, Ravishankar
> <[email protected]>; K, Kiran <[email protected]>; Bag, Amit K
> <[email protected]>; Raghuram Hegde <[email protected]>
> Subject: Re: [PATCH v4] Bluetooth: btintel: Add *setup* function for new
> generation Intel controllers
>
> Hi Kiran,
>
> On Thu, Oct 1, 2020 at 11:58 PM Kiran K <[email protected]> wrote:
> >
> > From: Kiran K <[email protected]>
> >
> > 1) add a helper function to download firmware
> >
> > 2) add a function to construct firmware / ddc file name
> >
> > 3) add a flag to identify new geneeration Intel controllers
> >
> > 4) define *setup* and hook it up for new genertion Intel controllers
> >
> > 5) map Typhoon Peak controller (PID:0x0032) to new generation
> > controller
>
> Instead of enumerating the changes here it would probably make more
> sense to have them as separate patches.
I did had separate patches in v1. But patches weren't getting clean compiled as static functions weren't called in the same patch. I will move controller mapping in probe list into a separate patch. Let me know if this can be done in a better way.
>
> > Signed-off-by: Kiran K <[email protected]>
> > Signed-off-by: Amit K Bag <[email protected]>
> > Signed-off-by: Raghuram Hegde <[email protected]>
> > Reviewed-by: Sathish Narasimman <[email protected]>
> > Reviewed-by: Chethan T N <[email protected]>
> > Reviewed-by: Srivatsa Ravishankar <[email protected]>
> > ---
> > drivers/bluetooth/btintel.h | 6 +
> > drivers/bluetooth/btusb.c | 324
> +++++++++++++++++++++++++++++++++++++++++++-
> > 2 files changed, 328 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/bluetooth/btintel.h b/drivers/bluetooth/btintel.h
> > index 09346ae..c4e28a8 100644
> > --- a/drivers/bluetooth/btintel.h
> > +++ b/drivers/bluetooth/btintel.h
> > @@ -132,6 +132,12 @@ struct intel_debug_features {
> > __u8 page1[16];
> > } __packed;
> >
> > +#define INTEL_HW_PLATFORM(cnvx_bt) ((u8)(((cnvx_bt) & 0x0000ff00)
> >> 8))
> > +#define INTEL_HW_VARIANT(cnvx_bt) ((u8)(((cnvx_bt) & 0x003f0000)
> >> 16))
> > +#define INTEL_CNVX_TOP_TYPE(cnvx_top) ((cnvx_top) & 0x00000fff)
> > +#define INTEL_CNVX_TOP_STEP(cnvx_top) (((cnvx_top) & 0x0f000000) >>
> > +24) #define INTEL_CNVX_TOP_PACK_SWAB(t, s) __swab16(((__u16)(((t) <<
> > +4) | (s))))
> > +
> > #if IS_ENABLED(CONFIG_BT_INTEL)
> >
> > int btintel_check_bdaddr(struct hci_dev *hdev); diff --git
> > a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index
> > 1005b6e..5e51749 100644
> > --- a/drivers/bluetooth/btusb.c
> > +++ b/drivers/bluetooth/btusb.c
> > @@ -60,6 +60,7 @@ static struct usb_driver btusb_driver; #define
> > BTUSB_WIDEBAND_SPEECH 0x400000
> > #define BTUSB_VALID_LE_STATES 0x800000
> > #define BTUSB_QCA_WCN6855 0x1000000
> > +#define BTUSB_INTEL_NEWGEN 0x2000000
>
> I wonder if it is a good idea to keep adding such flags per model here, it
> should be possible to pass the pid/vid so we don't have to add generation
> after generation here.
>
> >
> > static const struct usb_device_id btusb_table[] = {
> > /* Generic Bluetooth USB device */ @@ -365,7 +366,7 @@ static
> > const struct usb_device_id blacklist_table[] = {
> > BTUSB_WIDEBAND_SPEECH },
> > { USB_DEVICE(0x8087, 0x0029), .driver_info = BTUSB_INTEL_NEW |
> > BTUSB_WIDEBAND_SPEECH },
> > - { USB_DEVICE(0x8087, 0x0032), .driver_info = BTUSB_INTEL_NEW |
> > + { USB_DEVICE(0x8087, 0x0032), .driver_info =
> > + BTUSB_INTEL_NEWGEN |
> > BTUSB_WIDEBAND_SPEECH},
> > { USB_DEVICE(0x8087, 0x07da), .driver_info = BTUSB_CSR },
> > { USB_DEVICE(0x8087, 0x07dc), .driver_info = BTUSB_INTEL }, @@
> > -2359,6 +2360,181 @@ static bool
> btusb_setup_intel_new_get_fw_name(struct intel_version *ver,
> > return true;
> > }
> >
> > +static void btusb_setup_intel_newgen_get_fw_name(const struct
> intel_version_tlv *ver_tlv,
> > + char *fw_name, size_t len,
> > + const char *suffix) {
> > + /* The firmware file name for new generation controllers will be
> > + * ibt-<cnvi_top type+cnvi_top step>-<cnvr_top type+cnvr_top step>
> > + */
> > + snprintf(fw_name, len, "intel/ibt-%04x-%04x.%s",
> > + INTEL_CNVX_TOP_PACK_SWAB(INTEL_CNVX_TOP_TYPE(ver_tlv-
> >cnvi_top),
> > + INTEL_CNVX_TOP_STEP(ver_tlv->cnvi_top)),
> > + INTEL_CNVX_TOP_PACK_SWAB(INTEL_CNVX_TOP_TYPE(ver_tlv-
> >cnvr_top),
> > + INTEL_CNVX_TOP_STEP(ver_tlv->cnvr_top)),
> > + suffix);
> > +}
> > +
> > +static int btusb_intel_download_firmware_newgen(struct hci_dev *hdev,
> > + struct intel_version_tlv *ver,
> > + u32 *boot_param) {
> > + const struct firmware *fw;
> > + char fwname[64];
> > + int err;
> > + struct btusb_data *data = hci_get_drvdata(hdev);
> > +
> > + if (!ver || !boot_param)
> > + return -EINVAL;
> > +
> > + /* The hardware platform number has a fixed value of 0x37 and
> > + * for now only accept this single value.
> > + */
> > + if (INTEL_HW_PLATFORM(ver->cnvi_bt) != 0x37) {
> > + bt_dev_err(hdev, "Unsupported Intel hardware platform
> (0x%2x)",
> > + INTEL_HW_PLATFORM(ver->cnvi_bt));
> > + return -EINVAL;
> > + }
> > +
> > + /* The firmware variant determines if the device is in bootloader
> > + * mode or is running operational firmware. The value 0x03 identifies
> > + * the bootloader and the value 0x23 identifies the operational
> > + * firmware.
> > + *
> > + * When the operational firmware is already present, then only
> > + * the check for valid Bluetooth device address is needed. This
> > + * determines if the device will be added as configured or
> > + * unconfigured controller.
> > + *
> > + * It is not possible to use the Secure Boot Parameters in this
> > + * case since that command is only available in bootloader mode.
> > + */
> > + if (ver->img_type == 0x03) {
> > + clear_bit(BTUSB_BOOTLOADER, &data->flags);
> > + btintel_check_bdaddr(hdev);
> > + return 0;
> > + }
> > +
> > + /* Check for supported iBT hardware variants of this firmware
> > + * loading method.
> > + *
> > + * This check has been put in place to ensure correct forward
> > + * compatibility options when newer hardware variants come along.
> > + */
> > + switch (INTEL_HW_VARIANT(ver->cnvi_bt)) {
> > + case 0x17: /* TyP */
> > + case 0x18: /* Slr */
> > + case 0x19: /* Slr-F */
> > + break;
> > + default:
> > + bt_dev_err(hdev, "Unsupported Intel hardware variant (0x%x)",
> > + INTEL_HW_VARIANT(ver->cnvi_bt));
> > + return -EINVAL;
> > + }
> > +
> > + /* If the device is not in bootloader mode, then the only possible
> > + * choice is to return an error and abort the device initialization.
> > + */
> > + if (ver->img_type != 0x01) {
> > + bt_dev_err(hdev, "Unsupported Intel firmware variant (0x%x)",
> > + ver->img_type);
> > + return -ENODEV;
> > + }
> > +
> > + /* It is required that every single firmware fragment is acknowledged
> > + * with a command complete event. If the boot parameters indicate
> > + * that this bootloader does not send them, then abort the setup.
> > + */
> > + if (ver->limited_cce != 0x00) {
> > + bt_dev_err(hdev, "Unsupported Intel firmware loading method
> (0x%x)",
> > + ver->limited_cce);
> > + return -EINVAL;
> > + }
> > +
> > + /* Secure boot engine type should be either 1 (ECDSA) or 0 (RSA) */
> > + if (ver->sbe_type > 0x01) {
> > + bt_dev_err(hdev, "Unsupported Intel secure boot engine type
> (0x%x)",
> > + ver->sbe_type);
> > + return -EINVAL;
> > + }
> > +
> > + /* If the OTP has no valid Bluetooth device address, then there will
> > + * also be no valid address for the operational firmware.
> > + */
> > + if (!bacmp(&ver->otp_bd_addr, BDADDR_ANY)) {
> > + bt_dev_info(hdev, "No device address configured");
> > + set_bit(HCI_QUIRK_INVALID_BDADDR, &hdev->quirks);
> > + }
> > +
> > + btusb_setup_intel_newgen_get_fw_name(ver, fwname,
> sizeof(fwname), "sfi");
> > + err = request_firmware(&fw, fwname, &hdev->dev);
> > + if (err < 0) {
> > + bt_dev_err(hdev, "Failed to load Intel firmware file (%d)", err);
> > + return err;
> > + }
> > +
> > + bt_dev_info(hdev, "Found device firmware: %s", fwname);
> > +
> > + if (fw->size < 644) {
> > + bt_dev_err(hdev, "Invalid size of firmware file (%zu)",
> > + fw->size);
> > + err = -EBADF;
> > + goto done;
> > + }
> > +
> > + set_bit(BTUSB_DOWNLOADING, &data->flags);
> > +
> > + /* Start firmware downloading and get boot parameter */
> > + err = btintel_download_firmware_newgen(hdev, fw, boot_param,
> > + INTEL_HW_VARIANT(ver->cnvi_bt),
> > + ver->sbe_type);
> > + if (err < 0) {
> > + /* When FW download fails, send Intel Reset to retry
> > + * FW download.
> > + */
> > + btintel_reset_to_bootloader(hdev);
> > + goto done;
> > + }
> > + set_bit(BTUSB_FIRMWARE_LOADED, &data->flags);
> > +
> > + bt_dev_info(hdev, "Waiting for firmware download to
> > + complete");
> > +
> > + /* Before switching the device into operational mode and with that
> > + * booting the loaded firmware, wait for the bootloader notification
> > + * that all fragments have been successfully received.
> > + *
> > + * When the event processing receives the notification, then the
> > + * BTUSB_DOWNLOADING flag will be cleared.
> > + *
> > + * The firmware loading should not take longer than 5 seconds
> > + * and thus just timeout if that happens and fail the setup
> > + * of this device.
> > + */
> > + err = wait_on_bit_timeout(&data->flags, BTUSB_DOWNLOADING,
> > + TASK_INTERRUPTIBLE,
> > + msecs_to_jiffies(5000));
> > + if (err == -EINTR) {
> > + bt_dev_err(hdev, "Firmware loading interrupted");
> > + goto done;
> > + }
> > +
> > + if (err) {
> > + bt_dev_err(hdev, "Firmware loading timeout");
> > + err = -ETIMEDOUT;
> > + btintel_reset_to_bootloader(hdev);
> > + goto done;
> > + }
> > +
> > + if (test_bit(BTUSB_FIRMWARE_FAILED, &data->flags)) {
> > + bt_dev_err(hdev, "Firmware loading failed");
> > + err = -ENOEXEC;
> > + goto done;
> > + }
> > +
> > +done:
> > + release_firmware(fw);
> > + return err;
> > +}
> > static int btusb_intel_download_firmware(struct hci_dev *hdev,
> > struct intel_version *ver,
> > struct intel_boot_params
> > *params, @@ -2693,6 +2869,135 @@ static int
> btusb_setup_intel_new(struct hci_dev *hdev)
> > return 0;
> > }
> >
> > +static int btusb_setup_intel_newgen(struct hci_dev *hdev) {
> > + struct btusb_data *data = hci_get_drvdata(hdev);
> > + u32 boot_param;
> > + char ddcname[64];
> > + ktime_t calltime, delta, rettime;
> > + unsigned long long duration;
> > + int err;
> > + struct intel_debug_features features;
> > + struct intel_version_tlv version;
> > +
> > + BT_DBG("%s", hdev->name);
> > +
> > + /* Set the default boot parameter to 0x0 and it is updated to
> > + * SKU specific boot parameter after reading Intel_Write_Boot_Params
> > + * command while downloading the firmware.
> > + */
> > + boot_param = 0x00000000;
> > +
> > + calltime = ktime_get();
> > +
> > + /* Read the Intel version information to determine if the device
> > + * is in bootloader mode or if it already has operational firmware
> > + * loaded.
> > + */
> > + err = btintel_read_version_tlv(hdev, &version);
> > + if (err) {
> > + bt_dev_err(hdev, "Intel Read version failed (%d)", err);
> > + btintel_reset_to_bootloader(hdev);
> > + return err;
> > + }
> > +
> > + btintel_version_info_tlv(hdev, &version);
> > +
> > + err = btusb_intel_download_firmware_newgen(hdev, &version,
> &boot_param);
> > + if (err)
> > + return err;
> > +
> > + /* check if controller is already having an operational firmware */
> > + if (version.img_type == 0x03)
> > + goto finish;
> > +
> > + rettime = ktime_get();
> > + delta = ktime_sub(rettime, calltime);
> > + duration = (unsigned long long)ktime_to_ns(delta) >> 10;
> > +
> > + bt_dev_info(hdev, "Firmware loaded in %llu usecs", duration);
> > +
> > + calltime = ktime_get();
> > +
> > + set_bit(BTUSB_BOOTING, &data->flags);
> > +
> > + err = btintel_send_intel_reset(hdev, boot_param);
> > + if (err) {
> > + bt_dev_err(hdev, "Intel Soft Reset failed (%d)", err);
> > + btintel_reset_to_bootloader(hdev);
> > + return err;
> > + }
> > +
> > + /* The bootloader will not indicate when the device is ready. This
> > + * is done by the operational firmware sending bootup notification.
> > + *
> > + * Booting into operational firmware should not take longer than
> > + * 1 second. However if that happens, then just fail the setup
> > + * since something went wrong.
> > + */
> > + bt_dev_info(hdev, "Waiting for device to boot");
> > +
> > + err = wait_on_bit_timeout(&data->flags, BTUSB_BOOTING,
> > + TASK_INTERRUPTIBLE,
> > + msecs_to_jiffies(1000));
> > +
> > + if (err == -EINTR) {
> > + bt_dev_err(hdev, "Device boot interrupted");
> > + return -EINTR;
> > + }
> > +
> > + if (err) {
> > + bt_dev_err(hdev, "Device boot timeout");
> > + btintel_reset_to_bootloader(hdev);
> > + return -ETIMEDOUT;
> > + }
> > +
> > + rettime = ktime_get();
> > + delta = ktime_sub(rettime, calltime);
> > + duration = (unsigned long long)ktime_to_ns(delta) >> 10;
> > +
> > + bt_dev_info(hdev, "Device booted in %llu usecs", duration);
> > +
> > + clear_bit(BTUSB_BOOTLOADER, &data->flags);
> > +
> > + btusb_setup_intel_newgen_get_fw_name(&version, ddcname,
> sizeof(ddcname),
> > + "ddc");
> > +
> > + /* Once the device is running in operational mode, it needs to
> > + * apply the device configuration (DDC) parameters.
> > + *
> > + * The device can work without DDC parameters, so even if it
> > + * fails to load the file, no need to fail the setup.
> > + */
> > + btintel_load_ddc_config(hdev, ddcname);
> > +
> > + /* Read the Intel supported features and if new exception formats
> > + * supported, need to load the additional DDC config to enable.
> > + */
> > + btintel_read_debug_features(hdev, &features);
> > +
> > + /* Set DDC mask for available debug features */
> > + btintel_set_debug_features(hdev, &features);
> > +
> > + /* Read the Intel version information after loading the FW */
> > + err = btintel_read_version_tlv(hdev, &version);
> > + if (err)
> > + return err;
> > +
> > + btintel_version_info_tlv(hdev, &version);
> > +
> > +finish:
> > + /* Set the event mask for Intel specific vendor events. This enables
> > + * a few extra events that are useful during general operation. It
> > + * does not enable any debugging related events.
> > + *
> > + * The device will function correctly without these events enabled
> > + * and thus no need to fail the setup.
> > + */
> > + btintel_set_event_mask(hdev, false);
> > +
> > + return 0;
> > +}
> > static int btusb_shutdown_intel(struct hci_dev *hdev) {
> > struct sk_buff *skb;
> > @@ -3969,7 +4274,8 @@ static int btusb_probe(struct usb_interface *intf,
> > init_usb_anchor(&data->ctrl_anchor);
> > spin_lock_init(&data->rxlock);
> >
> > - if (id->driver_info & BTUSB_INTEL_NEW) {
> > + if ((id->driver_info & BTUSB_INTEL_NEW) ||
> > + (id->driver_info & BTUSB_INTEL_NEWGEN)) {
> > data->recv_event = btusb_recv_event_intel;
> > data->recv_bulk = btusb_recv_bulk_intel;
> > set_bit(BTUSB_BOOTLOADER, &data->flags); @@ -4078,6
> > +4384,20 @@ static int btusb_probe(struct usb_interface *intf,
> > set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
> > }
> >
> > + if (id->driver_info & BTUSB_INTEL_NEWGEN) {
> > + hdev->manufacturer = 2;
> > + hdev->send = btusb_send_frame_intel;
> > + hdev->setup = btusb_setup_intel_newgen;
> > + hdev->shutdown = btusb_shutdown_intel_new;
> > + hdev->hw_error = btintel_hw_error;
> > + hdev->set_diag = btintel_set_diag;
> > + hdev->set_bdaddr = btintel_set_bdaddr;
> > + hdev->cmd_timeout = btusb_intel_cmd_timeout;
> > + set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
> > + set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
> > + set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
> > + }
> > +
> > if (id->driver_info & BTUSB_MARVELL)
> > hdev->set_bdaddr = btusb_set_bdaddr_marvell;
> >
> > --
> > 2.7.4
> >
>
>
> --
> Luiz Augusto von Dentz
Regards,
Kiran
Hi Luiz,
Friendly reminder.!!
> -----Original Message-----
> From: K, Kiran
> Sent: Monday, October 5, 2020 7:44 AM
> To: 'Luiz Augusto von Dentz' <[email protected]>; Kiran K
> <[email protected]>
> Cc: [email protected]; Narasimman, Sathish
> <[email protected]>; Tumkur Narayan, Chethan
> <[email protected]>; Srivatsa, Ravishankar
> <[email protected]>; Bag, Amit K <[email protected]>;
> Raghuram Hegde <[email protected]>
> Subject: RE: [PATCH v4] Bluetooth: btintel: Add *setup* function for new
> generation Intel controllers
>
> Hi Luiz,
>
> > -----Original Message-----
> > From: Luiz Augusto von Dentz <[email protected]>
> > Sent: Friday, October 2, 2020 11:32 PM
> > To: Kiran K <[email protected]>
> > Cc: [email protected]; Narasimman, Sathish
> > <[email protected]>; Tumkur Narayan, Chethan
> > <[email protected]>; Srivatsa, Ravishankar
> > <[email protected]>; K, Kiran <[email protected]>; Bag,
> > Amit K <[email protected]>; Raghuram Hegde
> > <[email protected]>
> > Subject: Re: [PATCH v4] Bluetooth: btintel: Add *setup* function for
> > new generation Intel controllers
> >
> > Hi Kiran,
> >
> > On Thu, Oct 1, 2020 at 11:58 PM Kiran K <[email protected]> wrote:
> > >
> > > From: Kiran K <[email protected]>
> > >
> > > 1) add a helper function to download firmware
> > >
> > > 2) add a function to construct firmware / ddc file name
> > >
> > > 3) add a flag to identify new geneeration Intel controllers
> > >
> > > 4) define *setup* and hook it up for new genertion Intel controllers
> > >
> > > 5) map Typhoon Peak controller (PID:0x0032) to new generation
> > > controller
> >
> > Instead of enumerating the changes here it would probably make more
> > sense to have them as separate patches.
>
> I did had separate patches in v1. But patches weren't getting clean compiled
> as static functions weren't called in the same patch. I will move controller
> mapping in probe list into a separate patch. Let me know if this can be done
> in a better way.
>
> >
> > > Signed-off-by: Kiran K <[email protected]>
> > > Signed-off-by: Amit K Bag <[email protected]>
> > > Signed-off-by: Raghuram Hegde <[email protected]>
> > > Reviewed-by: Sathish Narasimman <[email protected]>
> > > Reviewed-by: Chethan T N <[email protected]>
> > > Reviewed-by: Srivatsa Ravishankar <[email protected]>
> > > ---
> > > drivers/bluetooth/btintel.h | 6 +
> > > drivers/bluetooth/btusb.c | 324
> > +++++++++++++++++++++++++++++++++++++++++++-
> > > 2 files changed, 328 insertions(+), 2 deletions(-)
> > >
> > > diff --git a/drivers/bluetooth/btintel.h
> > > b/drivers/bluetooth/btintel.h index 09346ae..c4e28a8 100644
> > > --- a/drivers/bluetooth/btintel.h
> > > +++ b/drivers/bluetooth/btintel.h
> > > @@ -132,6 +132,12 @@ struct intel_debug_features {
> > > __u8 page1[16];
> > > } __packed;
> > >
> > > +#define INTEL_HW_PLATFORM(cnvx_bt) ((u8)(((cnvx_bt) &
> 0x0000ff00)
> > >> 8))
> > > +#define INTEL_HW_VARIANT(cnvx_bt) ((u8)(((cnvx_bt) & 0x003f0000)
> > >> 16))
> > > +#define INTEL_CNVX_TOP_TYPE(cnvx_top) ((cnvx_top) & 0x00000fff)
> > > +#define INTEL_CNVX_TOP_STEP(cnvx_top) (((cnvx_top) & 0x0f000000)
> > > +>>
> > > +24) #define INTEL_CNVX_TOP_PACK_SWAB(t, s) __swab16(((__u16)(((t)
> > > +<<
> > > +4) | (s))))
> > > +
> > > #if IS_ENABLED(CONFIG_BT_INTEL)
> > >
> > > int btintel_check_bdaddr(struct hci_dev *hdev); diff --git
> > > a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c index
> > > 1005b6e..5e51749 100644
> > > --- a/drivers/bluetooth/btusb.c
> > > +++ b/drivers/bluetooth/btusb.c
> > > @@ -60,6 +60,7 @@ static struct usb_driver btusb_driver; #define
> > > BTUSB_WIDEBAND_SPEECH 0x400000
> > > #define BTUSB_VALID_LE_STATES 0x800000
> > > #define BTUSB_QCA_WCN6855 0x1000000
> > > +#define BTUSB_INTEL_NEWGEN 0x2000000
> >
> > I wonder if it is a good idea to keep adding such flags per model
> > here, it should be possible to pass the pid/vid so we don't have to
> > add generation after generation here.
> >
> > >
> > > static const struct usb_device_id btusb_table[] = {
> > > /* Generic Bluetooth USB device */ @@ -365,7 +366,7 @@
> > > static const struct usb_device_id blacklist_table[] = {
> > > BTUSB_WIDEBAND_SPEECH },
> > > { USB_DEVICE(0x8087, 0x0029), .driver_info = BTUSB_INTEL_NEW |
> > > BTUSB_WIDEBAND_SPEECH },
> > > - { USB_DEVICE(0x8087, 0x0032), .driver_info = BTUSB_INTEL_NEW |
> > > + { USB_DEVICE(0x8087, 0x0032), .driver_info =
> > > + BTUSB_INTEL_NEWGEN |
> > > BTUSB_WIDEBAND_SPEECH},
> > > { USB_DEVICE(0x8087, 0x07da), .driver_info = BTUSB_CSR },
> > > { USB_DEVICE(0x8087, 0x07dc), .driver_info = BTUSB_INTEL },
> > > @@
> > > -2359,6 +2360,181 @@ static bool
> > btusb_setup_intel_new_get_fw_name(struct intel_version *ver,
> > > return true;
> > > }
> > >
> > > +static void btusb_setup_intel_newgen_get_fw_name(const struct
> > intel_version_tlv *ver_tlv,
> > > + char *fw_name, size_t len,
> > > + const char *suffix) {
> > > + /* The firmware file name for new generation controllers will be
> > > + * ibt-<cnvi_top type+cnvi_top step>-<cnvr_top type+cnvr_top step>
> > > + */
> > > + snprintf(fw_name, len, "intel/ibt-%04x-%04x.%s",
> > > +
> > > + INTEL_CNVX_TOP_PACK_SWAB(INTEL_CNVX_TOP_TYPE(ver_tlv-
> > >cnvi_top),
> > > + INTEL_CNVX_TOP_STEP(ver_tlv->cnvi_top)),
> > > +
> > > + INTEL_CNVX_TOP_PACK_SWAB(INTEL_CNVX_TOP_TYPE(ver_tlv-
> > >cnvr_top),
> > > + INTEL_CNVX_TOP_STEP(ver_tlv->cnvr_top)),
> > > + suffix);
> > > +}
> > > +
> > > +static int btusb_intel_download_firmware_newgen(struct hci_dev
> *hdev,
> > > + struct intel_version_tlv *ver,
> > > + u32 *boot_param) {
> > > + const struct firmware *fw;
> > > + char fwname[64];
> > > + int err;
> > > + struct btusb_data *data = hci_get_drvdata(hdev);
> > > +
> > > + if (!ver || !boot_param)
> > > + return -EINVAL;
> > > +
> > > + /* The hardware platform number has a fixed value of 0x37 and
> > > + * for now only accept this single value.
> > > + */
> > > + if (INTEL_HW_PLATFORM(ver->cnvi_bt) != 0x37) {
> > > + bt_dev_err(hdev, "Unsupported Intel hardware
> > > + platform
> > (0x%2x)",
> > > + INTEL_HW_PLATFORM(ver->cnvi_bt));
> > > + return -EINVAL;
> > > + }
> > > +
> > > + /* The firmware variant determines if the device is in bootloader
> > > + * mode or is running operational firmware. The value 0x03
> identifies
> > > + * the bootloader and the value 0x23 identifies the operational
> > > + * firmware.
> > > + *
> > > + * When the operational firmware is already present, then only
> > > + * the check for valid Bluetooth device address is needed. This
> > > + * determines if the device will be added as configured or
> > > + * unconfigured controller.
> > > + *
> > > + * It is not possible to use the Secure Boot Parameters in this
> > > + * case since that command is only available in bootloader mode.
> > > + */
> > > + if (ver->img_type == 0x03) {
> > > + clear_bit(BTUSB_BOOTLOADER, &data->flags);
> > > + btintel_check_bdaddr(hdev);
> > > + return 0;
> > > + }
> > > +
> > > + /* Check for supported iBT hardware variants of this firmware
> > > + * loading method.
> > > + *
> > > + * This check has been put in place to ensure correct forward
> > > + * compatibility options when newer hardware variants come along.
> > > + */
> > > + switch (INTEL_HW_VARIANT(ver->cnvi_bt)) {
> > > + case 0x17: /* TyP */
> > > + case 0x18: /* Slr */
> > > + case 0x19: /* Slr-F */
> > > + break;
> > > + default:
> > > + bt_dev_err(hdev, "Unsupported Intel hardware variant (0x%x)",
> > > + INTEL_HW_VARIANT(ver->cnvi_bt));
> > > + return -EINVAL;
> > > + }
> > > +
> > > + /* If the device is not in bootloader mode, then the only possible
> > > + * choice is to return an error and abort the device initialization.
> > > + */
> > > + if (ver->img_type != 0x01) {
> > > + bt_dev_err(hdev, "Unsupported Intel firmware variant (0x%x)",
> > > + ver->img_type);
> > > + return -ENODEV;
> > > + }
> > > +
> > > + /* It is required that every single firmware fragment is
> acknowledged
> > > + * with a command complete event. If the boot parameters indicate
> > > + * that this bootloader does not send them, then abort the setup.
> > > + */
> > > + if (ver->limited_cce != 0x00) {
> > > + bt_dev_err(hdev, "Unsupported Intel firmware loading
> > > + method
> > (0x%x)",
> > > + ver->limited_cce);
> > > + return -EINVAL;
> > > + }
> > > +
> > > + /* Secure boot engine type should be either 1 (ECDSA) or 0 (RSA) */
> > > + if (ver->sbe_type > 0x01) {
> > > + bt_dev_err(hdev, "Unsupported Intel secure boot
> > > + engine type
> > (0x%x)",
> > > + ver->sbe_type);
> > > + return -EINVAL;
> > > + }
> > > +
> > > + /* If the OTP has no valid Bluetooth device address, then there will
> > > + * also be no valid address for the operational firmware.
> > > + */
> > > + if (!bacmp(&ver->otp_bd_addr, BDADDR_ANY)) {
> > > + bt_dev_info(hdev, "No device address configured");
> > > + set_bit(HCI_QUIRK_INVALID_BDADDR, &hdev->quirks);
> > > + }
> > > +
> > > + btusb_setup_intel_newgen_get_fw_name(ver, fwname,
> > sizeof(fwname), "sfi");
> > > + err = request_firmware(&fw, fwname, &hdev->dev);
> > > + if (err < 0) {
> > > + bt_dev_err(hdev, "Failed to load Intel firmware file (%d)", err);
> > > + return err;
> > > + }
> > > +
> > > + bt_dev_info(hdev, "Found device firmware: %s", fwname);
> > > +
> > > + if (fw->size < 644) {
> > > + bt_dev_err(hdev, "Invalid size of firmware file (%zu)",
> > > + fw->size);
> > > + err = -EBADF;
> > > + goto done;
> > > + }
> > > +
> > > + set_bit(BTUSB_DOWNLOADING, &data->flags);
> > > +
> > > + /* Start firmware downloading and get boot parameter */
> > > + err = btintel_download_firmware_newgen(hdev, fw, boot_param,
> > > + INTEL_HW_VARIANT(ver->cnvi_bt),
> > > + ver->sbe_type);
> > > + if (err < 0) {
> > > + /* When FW download fails, send Intel Reset to retry
> > > + * FW download.
> > > + */
> > > + btintel_reset_to_bootloader(hdev);
> > > + goto done;
> > > + }
> > > + set_bit(BTUSB_FIRMWARE_LOADED, &data->flags);
> > > +
> > > + bt_dev_info(hdev, "Waiting for firmware download to
> > > + complete");
> > > +
> > > + /* Before switching the device into operational mode and with that
> > > + * booting the loaded firmware, wait for the bootloader notification
> > > + * that all fragments have been successfully received.
> > > + *
> > > + * When the event processing receives the notification, then the
> > > + * BTUSB_DOWNLOADING flag will be cleared.
> > > + *
> > > + * The firmware loading should not take longer than 5 seconds
> > > + * and thus just timeout if that happens and fail the setup
> > > + * of this device.
> > > + */
> > > + err = wait_on_bit_timeout(&data->flags, BTUSB_DOWNLOADING,
> > > + TASK_INTERRUPTIBLE,
> > > + msecs_to_jiffies(5000));
> > > + if (err == -EINTR) {
> > > + bt_dev_err(hdev, "Firmware loading interrupted");
> > > + goto done;
> > > + }
> > > +
> > > + if (err) {
> > > + bt_dev_err(hdev, "Firmware loading timeout");
> > > + err = -ETIMEDOUT;
> > > + btintel_reset_to_bootloader(hdev);
> > > + goto done;
> > > + }
> > > +
> > > + if (test_bit(BTUSB_FIRMWARE_FAILED, &data->flags)) {
> > > + bt_dev_err(hdev, "Firmware loading failed");
> > > + err = -ENOEXEC;
> > > + goto done;
> > > + }
> > > +
> > > +done:
> > > + release_firmware(fw);
> > > + return err;
> > > +}
> > > static int btusb_intel_download_firmware(struct hci_dev *hdev,
> > > struct intel_version *ver,
> > > struct intel_boot_params
> > > *params, @@ -2693,6 +2869,135 @@ static int
> > btusb_setup_intel_new(struct hci_dev *hdev)
> > > return 0;
> > > }
> > >
> > > +static int btusb_setup_intel_newgen(struct hci_dev *hdev) {
> > > + struct btusb_data *data = hci_get_drvdata(hdev);
> > > + u32 boot_param;
> > > + char ddcname[64];
> > > + ktime_t calltime, delta, rettime;
> > > + unsigned long long duration;
> > > + int err;
> > > + struct intel_debug_features features;
> > > + struct intel_version_tlv version;
> > > +
> > > + BT_DBG("%s", hdev->name);
> > > +
> > > + /* Set the default boot parameter to 0x0 and it is updated to
> > > + * SKU specific boot parameter after reading
> Intel_Write_Boot_Params
> > > + * command while downloading the firmware.
> > > + */
> > > + boot_param = 0x00000000;
> > > +
> > > + calltime = ktime_get();
> > > +
> > > + /* Read the Intel version information to determine if the device
> > > + * is in bootloader mode or if it already has operational firmware
> > > + * loaded.
> > > + */
> > > + err = btintel_read_version_tlv(hdev, &version);
> > > + if (err) {
> > > + bt_dev_err(hdev, "Intel Read version failed (%d)", err);
> > > + btintel_reset_to_bootloader(hdev);
> > > + return err;
> > > + }
> > > +
> > > + btintel_version_info_tlv(hdev, &version);
> > > +
> > > + err = btusb_intel_download_firmware_newgen(hdev, &version,
> > &boot_param);
> > > + if (err)
> > > + return err;
> > > +
> > > + /* check if controller is already having an operational firmware */
> > > + if (version.img_type == 0x03)
> > > + goto finish;
> > > +
> > > + rettime = ktime_get();
> > > + delta = ktime_sub(rettime, calltime);
> > > + duration = (unsigned long long)ktime_to_ns(delta) >> 10;
> > > +
> > > + bt_dev_info(hdev, "Firmware loaded in %llu usecs",
> > > + duration);
> > > +
> > > + calltime = ktime_get();
> > > +
> > > + set_bit(BTUSB_BOOTING, &data->flags);
> > > +
> > > + err = btintel_send_intel_reset(hdev, boot_param);
> > > + if (err) {
> > > + bt_dev_err(hdev, "Intel Soft Reset failed (%d)", err);
> > > + btintel_reset_to_bootloader(hdev);
> > > + return err;
> > > + }
> > > +
> > > + /* The bootloader will not indicate when the device is ready. This
> > > + * is done by the operational firmware sending bootup notification.
> > > + *
> > > + * Booting into operational firmware should not take longer than
> > > + * 1 second. However if that happens, then just fail the setup
> > > + * since something went wrong.
> > > + */
> > > + bt_dev_info(hdev, "Waiting for device to boot");
> > > +
> > > + err = wait_on_bit_timeout(&data->flags, BTUSB_BOOTING,
> > > + TASK_INTERRUPTIBLE,
> > > + msecs_to_jiffies(1000));
> > > +
> > > + if (err == -EINTR) {
> > > + bt_dev_err(hdev, "Device boot interrupted");
> > > + return -EINTR;
> > > + }
> > > +
> > > + if (err) {
> > > + bt_dev_err(hdev, "Device boot timeout");
> > > + btintel_reset_to_bootloader(hdev);
> > > + return -ETIMEDOUT;
> > > + }
> > > +
> > > + rettime = ktime_get();
> > > + delta = ktime_sub(rettime, calltime);
> > > + duration = (unsigned long long)ktime_to_ns(delta) >> 10;
> > > +
> > > + bt_dev_info(hdev, "Device booted in %llu usecs", duration);
> > > +
> > > + clear_bit(BTUSB_BOOTLOADER, &data->flags);
> > > +
> > > + btusb_setup_intel_newgen_get_fw_name(&version, ddcname,
> > sizeof(ddcname),
> > > + "ddc");
> > > +
> > > + /* Once the device is running in operational mode, it needs to
> > > + * apply the device configuration (DDC) parameters.
> > > + *
> > > + * The device can work without DDC parameters, so even if it
> > > + * fails to load the file, no need to fail the setup.
> > > + */
> > > + btintel_load_ddc_config(hdev, ddcname);
> > > +
> > > + /* Read the Intel supported features and if new exception formats
> > > + * supported, need to load the additional DDC config to enable.
> > > + */
> > > + btintel_read_debug_features(hdev, &features);
> > > +
> > > + /* Set DDC mask for available debug features */
> > > + btintel_set_debug_features(hdev, &features);
> > > +
> > > + /* Read the Intel version information after loading the FW */
> > > + err = btintel_read_version_tlv(hdev, &version);
> > > + if (err)
> > > + return err;
> > > +
> > > + btintel_version_info_tlv(hdev, &version);
> > > +
> > > +finish:
> > > + /* Set the event mask for Intel specific vendor events. This enables
> > > + * a few extra events that are useful during general operation. It
> > > + * does not enable any debugging related events.
> > > + *
> > > + * The device will function correctly without these events enabled
> > > + * and thus no need to fail the setup.
> > > + */
> > > + btintel_set_event_mask(hdev, false);
> > > +
> > > + return 0;
> > > +}
> > > static int btusb_shutdown_intel(struct hci_dev *hdev) {
> > > struct sk_buff *skb;
> > > @@ -3969,7 +4274,8 @@ static int btusb_probe(struct usb_interface
> *intf,
> > > init_usb_anchor(&data->ctrl_anchor);
> > > spin_lock_init(&data->rxlock);
> > >
> > > - if (id->driver_info & BTUSB_INTEL_NEW) {
> > > + if ((id->driver_info & BTUSB_INTEL_NEW) ||
> > > + (id->driver_info & BTUSB_INTEL_NEWGEN)) {
> > > data->recv_event = btusb_recv_event_intel;
> > > data->recv_bulk = btusb_recv_bulk_intel;
> > > set_bit(BTUSB_BOOTLOADER, &data->flags); @@ -4078,6
> > > +4384,20 @@ static int btusb_probe(struct usb_interface *intf,
> > > set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
> > > }
> > >
> > > + if (id->driver_info & BTUSB_INTEL_NEWGEN) {
> > > + hdev->manufacturer = 2;
> > > + hdev->send = btusb_send_frame_intel;
> > > + hdev->setup = btusb_setup_intel_newgen;
> > > + hdev->shutdown = btusb_shutdown_intel_new;
> > > + hdev->hw_error = btintel_hw_error;
> > > + hdev->set_diag = btintel_set_diag;
> > > + hdev->set_bdaddr = btintel_set_bdaddr;
> > > + hdev->cmd_timeout = btusb_intel_cmd_timeout;
> > > + set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
> > > + set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev-
> >quirks);
> > > + set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
> > > + }
> > > +
> > > if (id->driver_info & BTUSB_MARVELL)
> > > hdev->set_bdaddr = btusb_set_bdaddr_marvell;
> > >
> > > --
> > > 2.7.4
> > >
> >
> >
> > --
> > Luiz Augusto von Dentz
>
> Regards,
> Kiran
Thanks,
Kiran