Return-Path: MIME-Version: 1.0 In-Reply-To: <2DBBB005-93A7-47ED-8E88-1D6B92ACCC07@holtmann.org> References: <2045332.GytFuFKTvp@ix> <2DBBB005-93A7-47ED-8E88-1D6B92ACCC07@holtmann.org> From: =?UTF-8?Q?Fran=C3=A7ois_Beaufort?= Date: Tue, 24 Nov 2015 13:05:06 +0100 Message-ID: Subject: Re: Unknown Connection Identifier To: Marcel Holtmann Cc: Szymon Janc , linux-bluetooth@vger.kernel.org Content-Type: text/plain; charset=UTF-8 List-ID: On Tue, Nov 24, 2015 at 12:00 PM, Marcel Holtmann wro= te: > Hi Francois, > >> Thanks both of you for your input. >> >> Here are my 100% reproducible steps: >> - Restart bluetoothd to start fresh >> - Remove cached device (remove 88:0F:10:9D:EB:42) >> - Run basic scan (scan on) >> - Wait for the device to pop up in results and stop scan (scan off) >> - Try to connect to it (connect 88:0F:10:9D:EB:42) >> >> As you can read below I now have 2 "LE Connection Complete (0x01)" event= s. >> >> Bluetooth monitor ver 5.35 >> =3D New Index: A4:17:31:78:A6:04 (BR/EDR,USB,hci0) >> [hci0] 0.624321 >> < HCI Command: LE Add Device To White List (0x08|0x0011) plen 7 >> [hci0] 11.038826 >> Address type: Public (0x00) >> Address: 88:0F:10:9D:EB:42 (OUI 88-0F-10) >>> HCI Event: Command Complete (0x0e) plen 4 = [hci0] 11.040084 >> LE Add Device To White List (0x08|0x0011) ncmd 1 >> Status: Success (0x00) >> < HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 >> [hci0] 11.040125 >> Type: Passive (0x00) >> Interval: 60.000 msec (0x0060) >> Window: 30.000 msec (0x0030) >> Own address type: Public (0x00) >> Filter policy: Ignore not in white list (0x01) >>> HCI Event: Command Complete (0x0e) plen 4 = [hci0] 11.041085 >> LE Set Scan Parameters (0x08|0x000b) ncmd 1 >> Status: Success (0x00) >> < HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 >> [hci0] 11.041134 >> Scanning: Enabled (0x01) >> Filter duplicates: Enabled (0x01) >>> HCI Event: Command Complete (0x0e) plen 4 = [hci0] 11.042084 >> LE Set Scan Enable (0x08|0x000c) ncmd 1 >> Status: Success (0x00) >>> HCI Event: LE Meta Event (0x3e) plen 43 = [hci0] 15.668141 >> LE Advertising Report (0x02) >> Num reports: 1 >> Event type: Connectable undirected - ADV_IND (0x00) >> Address type: Public (0x00) >> Address: 88:0F:10:9D:EB:42 (OUI 88-0F-10) >> Data length: 31 >> Flags: 0x06 >> LE General Discoverable Mode >> BR/EDR Not Supported >> Company: Anhui Huami Information Technology Co., Ltd. (343) >> Data: 00f70b676930f4c909f4a5acd792a299ff02880f109deb42 >> RSSI: -59 dBm (0xc5) >> < HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 >> [hci0] 15.668289 >> Scanning: Disabled (0x00) >> Filter duplicates: Disabled (0x00) >>> HCI Event: Command Complete (0x0e) plen 4 = [hci0] 15.669062 >> LE Set Scan Enable (0x08|0x000c) ncmd 1 >> Status: Success (0x00) >> < HCI Command: LE Create Connection (0x08|0x000d) plen 25 >> [hci0] 15.669171 >> Scan interval: 60.000 msec (0x0060) >> Scan window: 30.000 msec (0x0030) > > we might should have the LE Create Connection scan with a full duty cycle= here. So it does not miss any advertising PDUs. > >> Filter policy: White list is not used (0x00) >> Peer address type: Public (0x00) >> Peer address: 88:0F:10:9D:EB:42 (OUI 88-0F-10) >> Own address type: Public (0x00) >> Min connection interval: 50.00 msec (0x0028) >> Max connection interval: 70.00 msec (0x0038) >> Connection latency: 0x0000 >> Supervision timeout: 420 msec (0x002a) >> Min connection length: 0.000 msec (0x0000) >> Max connection length: 0.000 msec (0x0000) >>> HCI Event: Command Status (0x0f) plen 4 = [hci0] 15.670065 >> LE Create Connection (0x08|0x000d) ncmd 1 >> Status: Success (0x00) >> < HCI Command: LE Create Connection Cancel (0x08|0x000e) plen 0 >> [hci0] 17.670566 > > And I think we need to increase the timeout to something like 4-5 seconds= before we give up and try the next device that might have been found. > >>> HCI Event: Command Complete (0x0e) plen 4 = [hci0] 17.672048 >> LE Create Connection Cancel (0x08|0x000e) ncmd 1 >> Status: Success (0x00) >>> HCI Event: LE Meta Event (0x3e) plen 19 = [hci0] 17.674036 >> LE Connection Complete (0x01) >> Status: Unknown Connection Identifier (0x02) >> Handle: 32 >> Role: Master (0x00) >> Peer address type: Public (0x00) >> Peer address: 88:0F:10:9D:EB:42 (OUI 88-0F-10) >> Connection interval: 67.50 msec (0x0036) >> Connection latency: 0.00 msec (0x0000) >> Supervision timeout: 420 msec (0x002a) >> Master clock accuracy: 0x00 >> @ Connect Failed: 88:0F:10:9D:EB:42 (1) status 0x02 > > This one still needs to be fixed. It is a bug. The implementation is too = naive. The unknown connection identifier is actually the success case for L= E Create Connection Cancel command. And since we keep trying until the conn= ection timeout hits, this is not an error at this point. Where should I file that bug so that I can keep track of it? > > Regards > > Marcel >