Return-Path: MIME-Version: 1.0 In-Reply-To: <1459344056-5234-1-git-send-email-akarwar@marvell.com> References: <1459344056-5234-1-git-send-email-akarwar@marvell.com> From: Rob Herring Date: Wed, 30 Mar 2016 09:06:48 -0500 Message-ID: Subject: Re: [PATCH v6 1/2] dt: bindings: add MARVELL's bt-sd8xxx wireless device To: Amitkumar Karwar Cc: linux-bluetooth@vger.kernel.org, Nishant Sarmukadam , wnhuang@chromium.com, "devicetree@vger.kernel.org" , "linux-kernel@vger.kernel.org" , Xinming Hu Content-Type: text/plain; charset=UTF-8 Sender: linux-kernel-owner@vger.kernel.org List-ID: On Wed, Mar 30, 2016 at 8:20 AM, Amitkumar Karwar wrote: > From: Xinming Hu > > Add device tree binding documentation for MARVELL's bluetooth sdio > (sd8897 and sd8997) chip. > > Signed-off-by: Xinming Hu > Signed-off-by: Amitkumar Karwar > --- [...] > diff --git a/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt > new file mode 100644 > index 0000000..172ba83 > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/marvell-bt-sd8xxx.txt > @@ -0,0 +1,57 @@ > +Marvell 8897/8997 (sd8897/sd8997) bluetooth SDIO devices > +------ > + > +Required properties: > + > + - compatible : should be one of the following: > + * "marvell,sd8897-bt" > + * "marvell,sd8997-bt" > + > +Optional properties: > + > + - btmrvl,cal-data : Calibration data downloaded to the device during > + initialization. This is an array of 28 values(u8). btmrvl is not a vendor. These should all be "marvell". > + > + - btmrvl,wakeup-pin : 'wakeup-pin' represent wakeup pin number of the bluetooth > + chip. firmware will use the pin to wakeup host system. > + - btmrvl,wakeup-gap : wakeup gap (in msecs) represent wakeup latency of the host Add units suffix (-msec). > + platform. The value will be configure to fiwmware. s/fiwmware/firmware/ > + This is needed to work chip's sleep feature as expected. > + - interrupt-parent: phandle of the parent interrupt controller > + - interrupts : interrupt pin number to the cpu. driver will request an irq based on > + this interrupt number. during system suspend, the irq will be enabled > + as system wakeup source, so that the bluetooth chip can wakeup host > + platform under certain condition. during system resume, the irq will > + be disabled to make sure unnecessary interrupt is not received. > + > +Example: > + > +IRQ pin 119 is used as system wakeup source interrupt. > +wakeup pin 13 and gap 100ms are configured so that firmware can wakeup host > +using this device side pin and wakeup latency. > +calibration data is also available in below example. > + > +&mmc3 { > + status = "okay"; > + vmmc-supply = <&wlan_en_reg>; > + bus-width = <4>; > + cap-power-off-card; > + keep-power-in-suspend; > + > + #address-cells = <1>; > + #size-cells = <0>; > + btmrvl: btmrvl@2 { Use a generic node name: bluetooth@2 > + compatible = "marvell,sd8897-bt"; > + reg = <2>; > + interrupt-parent = <&pio>; > + interrupts = <119 IRQ_TYPE_LEVEL_LOW>; > + > + btmrvl,cal-data = /bits/ 8 < > + 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02 > + 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00 > + 0x00 0x00 0xf0 0x00>; > + btmrvl,wakeup-pin = <0x0d>; > + btmrvl,wakeup-gap = <0x64>; > + }; > +}; > + > -- > 1.8.1.4 > > -- > To unsubscribe from this list: send the line "unsubscribe devicetree" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html