Return-Path: <stefan.wahren@i2se.com>
Date: Fri, 4 Aug 2017 21:44:01 +0200 (CEST)
From: Stefan Wahren <stefan.wahren@i2se.com>
To: Marcel Holtmann <marcel@holtmann.org>
Cc: rjui@broadcom.com, sbranden@broadcom.com,
	Rob Herring <robh+dt@kernel.org>,
	Loic Poulain <loic.poulain@gmail.com>, f.fainelli@gmail.com,
	linux-rpi-kernel@lists.infradead.org,
	"open list:BLUETOOTH DRIVERS" <linux-bluetooth@vger.kernel.org>,
	Johan Hedberg <johan.hedberg@gmail.com>,
	devicetree <devicetree@vger.kernel.org>
Message-ID: <1498038890.121361.1501875841550@email.1und1.de>
In-Reply-To: <51D602E3-B21A-402B-A1F5-6241D55448E9@holtmann.org>
References: <1501576704-26423-1-git-send-email-loic.poulain@gmail.com>
 <1501576704-26423-3-git-send-email-loic.poulain@gmail.com>
 <696124D4-A5DA-46FA-A0F0-5DC74363BD23@holtmann.org>
 <444254163.121186.1501874785594@email.1und1.de>
 <51D602E3-B21A-402B-A1F5-6241D55448E9@holtmann.org>
Subject: Re: [PATCH v2 3/3] Bluetooth: hci_bcm: Add serdev support
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
List-ID: <linux-bluetooth.vger.kernel.org>


> Marcel Holtmann <marcel@holtmann.org> hat am 4. August 2017 um 21:37 geschrieben:
> 
> 
> Hi Stefan,
> 
> >>> Add basic support for Broadcom serial slave devices.
> >>> Probe the serial device, retrieve its maximum speed and
> >>> register a new hci uart device.
> >>> 
> >>> Tested/compatible with bcm43438 (RPi3).
> >>> 
> >>> Signed-off-by: Loic Poulain <loic.poulain@gmail.com>
> >>> ...
> >>> 
> >>> +static int bcm_serdev_probe(struct serdev_device *serdev)
> >>> +{
> >>> +	struct bcm_bt_device *bcmdev;
> >>> +	u32 speed;
> >>> +	int err;
> >>> +
> >>> +	bcmdev = devm_kzalloc(&serdev->dev, sizeof(*bcmdev), GFP_KERNEL);
> >>> +	if (!bcmdev)
> >>> +		return -ENOMEM;
> >>> +
> >>> +	bcmdev->hu.serdev = serdev;
> >>> +	serdev_device_set_drvdata(serdev, bcmdev);
> >>> +
> >>> +	err = of_property_read_u32(serdev->dev.of_node, "max-speed", &speed);
> >>> +	if (!err)
> >>> +		bcmdev->hu.oper_speed = speed;
> >>> +
> >>> +	return hci_uart_register_device(&bcmdev->hu, &bcm_proto);
> >>> +}
> >> 
> >> We do not need any GPIO for reset lines or anything else for the rPI3?
> >> 
> > 
> > unfortunately we don't have full schematics for RPI3, but according to firmware dt-blob.dts [1] there is a GPIO called BT_ON. This GPIO is controlled by the GPIO expander on the RPI3 board. The necessary driver for this expander is still out of tree (last mainlining attempt [2]).
> 
> so who handles this GPIO then right now (or any other GPIO for that matter)? I have seen Bluetooth being enabled and operational, but I really want to get this working in a plain upstream Fedora and without using hciattach or btattach.

The GPU firmware enables the GPIO and keeps this state. The mentioned expander driver should provide the ARM core (Linux) the necessary control.

> 
> Regards
> 
> Marcel
>