Received-SPF: pass (google.com: domain of linux-bluetooth-owner@vger.kernel.org designates 2620:137:e000::1:20 as permitted sender) client-ip=2620:137:e000::1:20;
From:   Hans de Goede <hdegoede@redhat.com>
To:     Marcel Holtmann <marcel@holtmann.org>,
        Johan Hedberg <johan.hedberg@gmail.com>,
        Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Cc:     Hans de Goede <hdegoede@redhat.com>,
        linux-bluetooth@vger.kernel.org,
        Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Subject: [PATCH] Bluetooth: hci_event: Fix vendor (unknown) opcode status handling
Date:   Sun,  7 Aug 2022 22:57:40 +0200
Message-Id: <20220807205740.777363-1-hdegoede@redhat.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

Commit c8992cffbe74 ("Bluetooth: hci_event: Use of a function table to
handle Command Complete") was (presumably) meant to only refactor things
without any functional changes.

But it does have one undesirable side-effect, before *status would always
be set to skb->data[0] and it might be overridden by some of the opcode
specific handling. While now it always set by the opcode specific handlers.
This means that if the opcode is not known *status does not get set any
more at all!

This behavior change has broken bluetooth support for BCM4343A0 HCIs,
the hci_bcm.c code tries to configure UART attached HCIs at a higher
baudraute using vendor specific opcodes. The BCM4343A0 does not
support this and this used to simply fail:

[   25.646442] Bluetooth: hci0: BCM: failed to write clock (-56)
[   25.646481] Bluetooth: hci0: Failed to set baudrate

After which things would continue with the initial baudraute. But now
that hci_cmd_complete_evt() no longer sets status for unknown opcodes
*status is left at 0. This causes the hci_bcm.c code to think the baudraute
has been changed on the HCI side and to also adjust the UART baudrate,
after which communication with the HCI is broken, leading to:

[   28.579042] Bluetooth: hci0: command 0x0c03 tx timeout
[   36.961601] Bluetooth: hci0: BCM: Reset failed (-110)

And non working bluetooth. Fix this by restoring the previous
default "*status = skb->data[0]" handling for unknown opcodes.

Fixes: c8992cffbe74 ("Bluetooth: hci_event: Use of a function table to handle Command Complete")
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
---
 net/bluetooth/hci_event.c | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/net/bluetooth/hci_event.c b/net/bluetooth/hci_event.c
index af17dfb20e01..fda31d558ded 100644
--- a/net/bluetooth/hci_event.c
+++ b/net/bluetooth/hci_event.c
@@ -3996,6 +3996,13 @@ static void hci_cmd_complete_evt(struct hci_dev *hdev, void *data,
 			break;
 		}
 	}
+	if (i == ARRAY_SIZE(hci_cc_table)) {
+		/* Unknown opcode, assume byte 0 contains the status, so
+		 * that e.g. __hci_cmd_sync() properly returns errors
+		 * for vendor specific commands send by HCI drivers.
+		 */
+		*status = skb->data[0];
+	}
 
 	handle_cmd_cnt_and_timer(hdev, ev->ncmd);
 
-- 
2.37.1