Return-Path: Subject: Re: [Bluez-users] Piconet problems From: Marcel Holtmann To: BlueZ Mailing List In-Reply-To: References: Content-Type: text/plain Message-Id: <1105737535.7525.48.camel@pegasus> Mime-Version: 1.0 Sender: bluez-users-admin@lists.sourceforge.net Errors-To: bluez-users-admin@lists.sourceforge.net Reply-To: bluez-users@lists.sourceforge.net List-Unsubscribe: , List-Id: BlueZ users List-Post: List-Help: List-Subscribe: , List-Archive: Date: Fri, 14 Jan 2005 22:18:55 +0100 Hi Jers, > > send us the outputs of "hciconfig -a" for all of your devices. And don't > > play with "hcitool cc". If you wanna test stuff then use l2test. > > hci0: Type: USB > BD Address: 00:08:E0:01:9E:86 ACL MTU: 192:8 SCO MTU: 64:8 > UP RUNNING PSCAN ISCAN > RX bytes:653 acl:0 sco:0 events:19 errors:0 > TX bytes:314 acl:0 sco:0 commands:18 errors:0 > Features: 0xff 0xff 0x0b 0x00 0x00 0x00 0x00 0x00 > Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 > Link policy: RSWITCH HOLD SNIFF PARK > Link mode: SLAVE ACCEPT > Name: 'PC A' > Class: 0x3e0100 > Service Classes: Networking, Rendering, Capturing > Device Class: Computer, Uncategorized > HCI Ver: 1.1 (0x1) HCI Rev: 0x33c LMP Ver: 1.1 (0x1) LMP Subver: 0x33c > Manufacturer: Cambridge Silicon Radio (10) > > hci0: Type: USB > BD Address: 00:E0:98:85:A1:64 ACL MTU: 192:8 SCO MTU: 64:8 > UP RUNNING PSCAN ISCAN > RX bytes:99 acl:0 sco:0 events:13 errors:0 > TX bytes:296 acl:0 sco:0 commands:12 errors:0 > Features: 0xff 0xff 0x0f 0x00 0x00 0x00 0x00 0x00 > Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3 > Link policy: RSWITCH HOLD SNIFF PARK > Link mode: SLAVE ACCEPT > Name: 'BlueZ (0)' > Class: 0x3e0100 > Service Classes: Networking, Rendering, Capturing > Device Class: Computer, Uncategorized > HCI Ver: 1.1 (0x1) HCI Rev: 0x175 LMP Ver: 1.1 (0x1) LMP Subver: 0x175 > Manufacturer: Cambridge Silicon Radio (10) the 0x175 firmwares are not HCI 16.4 and thus don't support scatternet and are difficult to connect. > > > After that, I tried to create the second connection on slave2 side by running the same command (hcitool cc > ) and I obtain the following error: > > > # Can't create connectio: input/output error. > > > > Run "hcidump -x" as root and show us the output. > > HCIDump - HCI packet analyzer ver 1.16 > device: hci0 snap_len: 1028 filter: 0xffffffff What about trying to connect now, so we see traffic? Regards Marcel ------------------------------------------------------- The SF.Net email is sponsored by: Beat the post-holiday blues Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek. It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt _______________________________________________ Bluez-users mailing list Bluez-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bluez-users