Return-Path: Date: Fri, 23 May 2008 16:24:05 +0800 (CST) From: attaboyu@163.com To: "BlueZ users" Message-ID: <28757280.111411211531045216.JavaMail.coremail@bj163app12.163.com> In-Reply-To: <20844183.487421211530034467.JavaMail.coremail@bj163app76.163.com> References: <20844183.487421211530034467.JavaMail.coremail@bj163app76.163.com> MIME-Version: 1.0 Subject: Re: [Bluez-users] CSR bluecore initial problem Reply-To: BlueZ users List-Id: BlueZ users List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Content-Type: multipart/mixed; boundary="===============0043058749==" Sender: bluez-users-bounces@lists.sourceforge.net Errors-To: bluez-users-bounces@lists.sourceforge.net --===============0043058749== Content-Type: multipart/alternative; boundary="----=_Part_29663_190559.1211531045214" ------=_Part_29663_190559.1211531045214 Content-Type: text/plain; charset=gbk Content-Transfer-Encoding: quoted-printable =20 and what's the difference between H4 and bcsp, while both of them use uart= interface? =20 =20 -- =20 hi all I got a problem while init the csr bluecore4 chip, my toolchain: bluez-3.12= , dbus-1.0.2,kernel-2.6.10 #dbus-daemon --system #hciattach ttyS0 bcsp #hcid -f /opt/bluez/etc/bluetooth/hcidconf #hciconfig=20 hci0: Type: UART BD Address: 00:02:5B:00:A5:A5 ACL MTU: 310:10 SCO MTU: 64:8 UP RUNNING PSCAN ISCAN=20 RX bytes:1128 acl:0 sco:0 events:23 errors:0 TX bytes:706 acl:0 sco:0 commands:26 errors:0 above is always ok. but csr chip need to set pskeys and warmreset,so I run bccmd #bccmd warmreset #hcitool scan Scanning Timeout... This problem around me for a few days, I cant figure out why the csr chip d= oesnt work after warmreset.UART0 connect to csr chip, so I choose bcsp conf= ig in kernel and choose hci interface(here i am not sure about choosing hci= or bcsp while run bccmd?), am i right? =20 =20 -- Best Regards ------------ Tony =C8=F0=D1=A9=B4=BA=CC=C3 =BC=B4=BD=AB=BF=AA=C6=F4 ------=_Part_29663_190559.1211531045214 Content-Type: text/html; charset=gbk Content-Transfer-Encoding: quoted-printable

and what's the difference between H4 and bcsp, = while both of them use uart interface?

= ;

=
hi all
I got a problem while init the csr bluecore4 chip, my toolc= hain: bluez-3.12, dbus-1.0.2,kernel-2.6.10
#dbus-daemon --system
#hci= attach ttyS0 bcsp
#hcid -f /opt/bluez/etc/bluetooth/hcidconf
#hc= iconfig
hci0:   Type: UART
        = BD Address: 00:02:5B:00:A5:A5 ACL MTU: 310:10 SCO MTU: 64:8
  =       UP RUNNING PSCAN ISCAN
   = ;     RX bytes:1128 acl:0 sco:0 events:23 errors:0
&= nbsp;       TX bytes:706 acl:0 sco:0 commands= :26 errors:0
above is always ok.
but csr chip need to set pskeys and warmreset,so I r= un bccmd
#bccmd warmreset
#hcitool scan
Scanning
Timeout...
=
This problem around me for a few days, I cant figure out why the csr ch= ip doesnt work after warmreset.UART0 connect to csr chip, so I choose bcsp = config in kernel and choose hci interface(here i am not sure about choosing= hci or bcsp while run bccmd?), am i right?

=

--

Best Regards
------------
Tony

=20
=C8=F0=D1=A9=B4=BA= =CC=C3 =BC=B4=BD=AB=BF=AA=C6=F4

=20

=C8=F0=D1=A9=B4=BA=CC=C3 =BC= =B4=BD=AB=BF=AA=C6=F4 ------=_Part_29663_190559.1211531045214-- --===============0043058749== Content-Type: text/plain; charset="us-ascii" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit Content-Disposition: inline ------------------------------------------------------------------------- This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008. http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/ --===============0043058749== Content-Type: text/plain; charset="us-ascii" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit Content-Disposition: inline _______________________________________________ Bluez-users mailing list Bluez-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bluez-users --===============0043058749==--