timenhhf wrote:
> hi,
> thanks for your reply.
> the attached file is the microcode file included in CSR2.4 crypto
> package that i got from INTEL's FAE.
> And the crypto function supported or not isn't really what i'm concern
> now, because after I startup the NPE module, the network can't work well.
> the detail steps as followed:
> (1)gcc -Wall IxNpeMicrocode.c -o IxNpeMicrocode
Which image are you specificing in the .h?
I currently use
IX_NPEDL_NPEIMAGE_NPEC_CRYPTO_AES_ETH_LEARN_FILTER_FIREWALL and
IX_NPEDL_NPEIMAGE_NPEB_ETH_SPAN_FIREWALL_VLAN_QOS_HDR_CONV
> (2)./IxNpeMicrocode (get NPE-B & NPE-C)
> (3)cp NPEs to /lib/firmware : cp -a NPE-* /lib/firmware/
> (4)Make ixp425's ramdisk.gz package
> (5)after system startup, do:
> echo "/sbin/mdev" > /proc/sys/kernel/hotplug
> /sbin/mdev -s
You should see the busybox doc. I do:
mount -t proc proc /proc
mount -t tmpfs -o size=64K mdev /dev
mkdir /dev/pts
mount -t devpts devpts /dev/pts
mount -t sysfs sysfs /sys
echo /sbin/mdev > /proc/sys/kernel/hotplug
mdev -s
> (6)insmod the NPE modules:
> modprobe ixp4xx_eth
> IXP4xx Queue Manager initialized.
> eth0: MII PHY 0 on NPE-B
> eth1: MII PHY 1 on NPE-C
if you modprobe ixp4xx_crypto does it come up?
> (7)lsmod to check:
> Module Size Used by Not tainted
> ixp4xx_eth 12824 0
> ixp4xx_npe 7200 3 ixp4xx_eth
> ixp4xx_qmgr 4824 1 ixp4xx_eth
> (8)set the NPE MAC address:
> ifconfig eth0 hw ether 00:03:05:06:07:08
> (9)ifconfig eth0 192.168.1.1 netmask 255.255.255.0
perhaps "ip link set eth0 up"
> (10) ping the NPE own interface:
> # ping -c 1 192.168.1.11
> PING 192.168.1.11 (192.168.1.11): 56 data bytes
> 64 bytes from 192.168.1.11: seq=0 ttl=64 time=0.539 ms
> (11)ping -c 1 192.168.1.98 (192.168.1.98 is the PC's ip address)
> PING 192.168.1.98 (192.168.1.98): 56 data bytes
> --- 192.168.1.98 ping statistics ---
> 1 packets transmitted, 0 packets received, 100% packet loss
> (12)check the interface status
> # ifconfig
> eth0 Link encap:Ethernet HWaddr 00:01:03:08:01:02
> inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:100
> RX bytes:0 (0.0 B) TX bytes:126 (126.0 B)
> Comments? thank you very much.
What does "ip link" and "ip addr" show?
perhaps send the entire "dmesg" it should contain info if the NPE is
starting up correctly.
--
--
Karl Hiramoto http://karl.hiramoto.org/