From: Lee Jones Subject: [PATCH 36/39] dmaengine: ste_dma40: Allow memcpy channels to be configured from DT Date: Wed, 15 May 2013 10:51:59 +0100 Message-ID: <1368611522-9984-37-git-send-email-lee.jones@linaro.org> References: <1368611522-9984-1-git-send-email-lee.jones@linaro.org> Cc: arnd@arndb.de, linus.walleij@stericsson.com, srinidhi.kasagar@stericsson.com, Lee Jones , Dan Williams , Per Forlin , Rabin Vincent To: linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, balbi@ti.com, linux-usb@vger.kernel.org, linux-crypto@vger.kernel.org, davem@davemloft.net, herbert@gondor.apana.org.au, vinod.koul@intel.com Return-path: Received: from mail-wg0-f41.google.com ([74.125.82.41]:57372 "EHLO mail-wg0-f41.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S932758Ab3EOJxS (ORCPT ); Wed, 15 May 2013 05:53:18 -0400 Received: by mail-wg0-f41.google.com with SMTP id y10so4922642wgg.4 for ; Wed, 15 May 2013 02:53:16 -0700 (PDT) In-Reply-To: <1368611522-9984-1-git-send-email-lee.jones@linaro.org> Sender: linux-crypto-owner@vger.kernel.org List-ID: At this moment in time the memcpy channels which can be used by the D40 are fixed, as each supported platform in Mainline uses the same ones. However, platforms do exist which don't follow this convention, so these will need to be tailored. Fortunately, these platforms will be DT only, so this change has very little impact on platform data. Cc: Vinod Koul Cc: Dan Williams Cc: Per Forlin Cc: Rabin Vincent Acked-by: Arnd Bergmann Signed-off-by: Lee Jones --- .../devicetree/bindings/dma/ste-dma40.txt | 2 + drivers/dma/ste_dma40.c | 40 ++++++++++++++++---- include/linux/platform_data/dma-ste-dma40.h | 2 + 3 files changed, 36 insertions(+), 8 deletions(-) diff --git a/Documentation/devicetree/bindings/dma/ste-dma40.txt b/Documentation/devicetree/bindings/dma/ste-dma40.txt index 2679a87..aa272d8 100644 --- a/Documentation/devicetree/bindings/dma/ste-dma40.txt +++ b/Documentation/devicetree/bindings/dma/ste-dma40.txt @@ -6,6 +6,7 @@ Required properties: - reg-names: Names of the above areas to use during resource look-up - interrupt: Should contain the DMAC interrupt number - #dma-cells: must be <3> +- memcpy-channels: Channels to be used for memcpy Optional properties: - dma-channels: Number of channels supported by hardware - if not present @@ -21,6 +22,7 @@ Example: interrupts = <0 25 0x4>; #dma-cells = <2>; + memcpy-channels = <56 57 58 59 60>; dma-channels = <8>; }; diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c index 76c255f..ae462d3 100644 --- a/drivers/dma/ste_dma40.c +++ b/drivers/dma/ste_dma40.c @@ -58,6 +58,8 @@ #define D40_ALLOC_PHY BIT(30) #define D40_ALLOC_LOG_FREE 0 +#define D40_MEMCPY_MAX_CHANS 8 + /* Reserved event lines for memcpy only. */ #define DB8500_DMA_MEMCPY_EV_0 51 #define DB8500_DMA_MEMCPY_EV_1 56 @@ -522,6 +524,8 @@ struct d40_gen_dmac { * @phy_start: Physical memory start of the DMA registers. * @phy_size: Size of the DMA register map. * @irq: The IRQ number. + * @num_memcpy_chans: The number of channels used for memcpy (mem-to-mem + * transfers). * @num_phy_chans: The number of physical channels. Read from HW. This * is the number of available channels for this driver, not counting "Secure * mode" allocated physical channels. @@ -565,6 +569,7 @@ struct d40_base { phys_addr_t phy_start; resource_size_t phy_size; int irq; + int num_memcpy_chans; int num_phy_chans; int num_log_chans; struct device_dma_parameters dma_parms; @@ -2938,7 +2943,7 @@ static int __init d40_dmaengine_init(struct d40_base *base, } d40_chan_init(base, &base->dma_memcpy, base->log_chans, - base->num_log_chans, ARRAY_SIZE(dma40_memcpy_channels)); + base->num_log_chans, base->num_memcpy_chans); dma_cap_zero(base->dma_memcpy.cap_mask); dma_cap_set(DMA_MEMCPY, base->dma_memcpy.cap_mask); @@ -3139,6 +3144,7 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev) struct d40_base *base = NULL; int num_log_chans = 0; int num_phy_chans; + int num_memcpy_chans; int clk_ret = -EINVAL; int i; u32 pid; @@ -3209,6 +3215,12 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev) else num_phy_chans = 4 * (readl(virtbase + D40_DREG_ICFG) & 0x7) + 4; + /* The number of channels used for memcpy */ + if (plat_data->num_of_memcpy_chans) + num_memcpy_chans = plat_data->num_of_memcpy_chans; + else + num_memcpy_chans = ARRAY_SIZE(dma40_memcpy_channels); + num_log_chans = num_phy_chans * D40_MAX_LOG_CHAN_PER_PHY; dev_info(&pdev->dev, @@ -3216,7 +3228,7 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev) rev, res->start, num_phy_chans, num_log_chans); base = kzalloc(ALIGN(sizeof(struct d40_base), 4) + - (num_phy_chans + num_log_chans + ARRAY_SIZE(dma40_memcpy_channels)) * + (num_phy_chans + num_log_chans + num_memcpy_chans) * sizeof(struct d40_chan), GFP_KERNEL); if (base == NULL) { @@ -3226,6 +3238,7 @@ static struct d40_base * __init d40_hw_detect_init(struct platform_device *pdev) base->rev = rev; base->clk = clk; + base->num_memcpy_chans = num_memcpy_chans; base->num_phy_chans = num_phy_chans; base->num_log_chans = num_log_chans; base->phy_start = res->start; @@ -3469,12 +3482,8 @@ static int __init d40_of_probe(struct platform_device *pdev, struct device_node *np) { struct stedma40_platform_data *pdata; - - /* - * FIXME: Fill in this routine as more support is added. - * First platform enabled (u8500) doens't need any extra - * properties to run, so this is fairly sparce currently. - */ + int num_memcpy = 0; + const const __be32 *list; pdata = devm_kzalloc(&pdev->dev, sizeof(struct stedma40_platform_data), @@ -3482,6 +3491,21 @@ static int __init d40_of_probe(struct platform_device *pdev, if (!pdata) return -ENOMEM; + list = of_get_property(np, "memcpy-channels", &num_memcpy); + num_memcpy /= sizeof(*list); + + if (num_memcpy > D40_MEMCPY_MAX_CHANS || num_memcpy <= 0) { + d40_err(&pdev->dev, + "Invalid number of memcpy channels specified (%d)\n", + num_memcpy); + return -EINVAL; + } + pdata->num_of_memcpy_chans = num_memcpy; + + of_property_read_u32_array(np, "memcpy-channels", + dma40_memcpy_channels, + num_memcpy); + pdev->dev.platform_data = pdata; return 0; diff --git a/include/linux/platform_data/dma-ste-dma40.h b/include/linux/platform_data/dma-ste-dma40.h index ceba6dc..1bb9b18 100644 --- a/include/linux/platform_data/dma-ste-dma40.h +++ b/include/linux/platform_data/dma-ste-dma40.h @@ -132,6 +132,7 @@ struct stedma40_chan_cfg { * @num_of_soft_lli_chans: The number of channels that needs to be configured * to use SoftLLI. * @use_esram_lcla: flag for mapping the lcla into esram region + * @num_of_memcpy_chans: The number of channels reserved for memcpy. * @num_of_phy_chans: The number of physical channels implemented in HW. * 0 means reading the number of channels from DMA HW but this is only valid * for 'multiple of 4' channels, like 8. @@ -141,6 +142,7 @@ struct stedma40_platform_data { int *soft_lli_chans; int num_of_soft_lli_chans; bool use_esram_lcla; + int num_of_memcpy_chans; int num_of_phy_chans; }; -- 1.7.10.4