2013-06-27 16:59:09

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 00/18] Add support for 5 and 10 MHz channels

This patchset adds support for 5 and 10 MHz in nl80211/cfg80211/mac80211
and enables support in ath5k and ath9k, which already support this feature
on the driver side. 5 and 10 MHz wide channels might be useful for:

* long shot links, as the transmissions are more robust
* future support for 802.11y which allows some 5 and 10 MHz channels in
3.6 GHz range
* future support for 802.11p which uses 10 MHz in 5.9 GHz range
* ... and more "special" applications.

This patchset enables 5 and 10 MHz channels only for OFDM, and without
HT/MIMO/aggregation (for now). Support may be added later.

Changes to PATCHv4 (all suggested by Johannes):

* change divisor to a shift when calculating 5/10 MHz bitrates or durations
to allow compiler optimization (binary shifts instead of integer divisions)
where possible
* change mandatory bitrates to accept the scan_width instead of rate flags
* typos, comments and style

As always, any comments are appreciated!
Cheers,
Simon


Simon Wunderlich (18):
nl80211: add scan width to bss and scan request structs
mac80211/rc80211: add chandef to rate initialization
mac80211: fix timing for 5 MHz and 10 MHz channels
mac80211: select and adjust bitrates according to channel mode
cfg80211/mac80211: get mandatory rates based on scan width
cfg80211/mac80211: use reduced txpower for 5 and 10 MHz
mac80211: add radiotap flag and handling for 5/10 MHz
mac80211: allow scanning for 5/10 MHz channels in IBSS
mac80211: return if IBSS chandef can not be used
nl80211: allow 5 and 10 MHz channels for IBSS
ath9k: always use SIFS times from OFDM for 5/10 MHz
ath9k: use chandef instead of channel_type
ath9k: report 5/10 MHz channels
ath9k: set 5/10 MHz supported channels and fix bitrate
ath9k: announce that ath9k supports 5/10 MHz
ath5k: report 5/10 MHz channels
ath5k: set 5/10 MHz supported channels and fix duration
ath5k: enable support for 5 MHz and 10 MHz channels

drivers/net/wireless/ath/ath5k/ath5k.h | 1 +
drivers/net/wireless/ath/ath5k/base.c | 59 ++++++--
drivers/net/wireless/ath/ath5k/base.h | 2 +-
drivers/net/wireless/ath/ath5k/mac80211-ops.c | 2 +-
drivers/net/wireless/ath/ath5k/pcu.c | 2 +
drivers/net/wireless/ath/ath5k/qcu.c | 25 +++-
drivers/net/wireless/ath/ath9k/common.c | 67 +++++----
drivers/net/wireless/ath/ath9k/common.h | 3 +-
drivers/net/wireless/ath/ath9k/htc_drv_main.c | 5 +-
drivers/net/wireless/ath/ath9k/hw.c | 5 +-
drivers/net/wireless/ath/ath9k/init.c | 29 ++--
drivers/net/wireless/ath/ath9k/main.c | 8 +-
drivers/net/wireless/ath/ath9k/rc.c | 11 +-
drivers/net/wireless/ath/ath9k/recv.c | 11 ++
drivers/net/wireless/iwlegacy/3945-rs.c | 1 +
drivers/net/wireless/iwlegacy/4965-rs.c | 1 +
drivers/net/wireless/iwlwifi/dvm/rs.c | 3 +-
drivers/net/wireless/iwlwifi/mvm/rs.c | 5 +-
drivers/net/wireless/rtlwifi/rc.c | 1 +
include/net/cfg80211.h | 85 ++++++++++-
include/net/ieee80211_radiotap.h | 4 +
include/net/mac80211.h | 6 +
include/uapi/linux/nl80211.h | 18 +++
net/mac80211/cfg.c | 48 +++----
net/mac80211/ibss.c | 124 ++++++++++++----
net/mac80211/ieee80211_i.h | 43 +++++-
net/mac80211/iface.c | 2 +-
net/mac80211/main.c | 15 +-
net/mac80211/mesh.c | 2 +-
net/mac80211/mesh_plink.c | 2 +-
net/mac80211/mlme.c | 98 +++++++------
net/mac80211/rate.c | 50 ++++---
net/mac80211/rate.h | 22 ++-
net/mac80211/rc80211_minstrel.c | 33 ++++-
net/mac80211/rc80211_minstrel_ht.c | 15 +-
net/mac80211/rc80211_pid_algo.c | 1 +
net/mac80211/rx.c | 28 ++--
net/mac80211/scan.c | 72 ++++++++--
net/mac80211/status.c | 17 ++-
net/mac80211/tx.c | 25 +++-
net/mac80211/util.c | 190 ++++++++++++++++++++-----
net/wireless/mesh.c | 5 +-
net/wireless/nl80211.c | 3 +
net/wireless/scan.c | 31 ++--
net/wireless/trace.h | 12 +-
net/wireless/util.c | 14 +-
46 files changed, 887 insertions(+), 319 deletions(-)

--
1.7.10.4



2013-06-27 16:59:15

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 09/18] mac80211: return if IBSS chandef can not be used

This was originally designed to fail when a 40+/40- mode can not be
used, but basic modes (such as 5/10/20 MHz) must be handled
with an error.

Signed-off-by: Simon Wunderlich <[email protected]>
---
net/mac80211/ibss.c | 8 ++++++++
1 file changed, 8 insertions(+)

diff --git a/net/mac80211/ibss.c b/net/mac80211/ibss.c
index 6adc5af..2e0256b 100644
--- a/net/mac80211/ibss.c
+++ b/net/mac80211/ibss.c
@@ -85,6 +85,14 @@ static void __ieee80211_sta_join_ibss(struct ieee80211_sub_if_data *sdata,

chandef = ifibss->chandef;
if (!cfg80211_reg_can_beacon(local->hw.wiphy, &chandef)) {
+ if (chandef.width == NL80211_CHAN_WIDTH_5 ||
+ chandef.width == NL80211_CHAN_WIDTH_10 ||
+ chandef.width == NL80211_CHAN_WIDTH_20_NOHT ||
+ chandef.width == NL80211_CHAN_WIDTH_20) {
+ sdata_info(sdata,
+ "Failed to join IBSS, beacons forbidden\n");
+ return;
+ }
chandef.width = NL80211_CHAN_WIDTH_20;
chandef.center_freq1 = chan->center_freq;
}
--
1.7.10.4


2013-06-27 16:59:19

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 17/18] ath5k: set 5/10 MHz supported channels and fix duration

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
drivers/net/wireless/ath/ath5k/base.c | 24 ++++++++++++++++--------
drivers/net/wireless/ath/ath5k/pcu.c | 2 ++
drivers/net/wireless/ath/ath5k/qcu.c | 25 ++++++++++++++++++++++++-
3 files changed, 42 insertions(+), 9 deletions(-)

diff --git a/drivers/net/wireless/ath/ath5k/base.c b/drivers/net/wireless/ath/ath5k/base.c
index 260a6fc..7c298af 100644
--- a/drivers/net/wireless/ath/ath5k/base.c
+++ b/drivers/net/wireless/ath/ath5k/base.c
@@ -165,28 +165,36 @@ static const struct ieee80211_rate ath5k_rates[] = {
.flags = IEEE80211_RATE_SHORT_PREAMBLE },
{ .bitrate = 60,
.hw_value = ATH5K_RATE_CODE_6M,
- .flags = 0 },
+ .flags = IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ },
{ .bitrate = 90,
.hw_value = ATH5K_RATE_CODE_9M,
- .flags = 0 },
+ .flags = IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ },
{ .bitrate = 120,
.hw_value = ATH5K_RATE_CODE_12M,
- .flags = 0 },
+ .flags = IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ },
{ .bitrate = 180,
.hw_value = ATH5K_RATE_CODE_18M,
- .flags = 0 },
+ .flags = IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ },
{ .bitrate = 240,
.hw_value = ATH5K_RATE_CODE_24M,
- .flags = 0 },
+ .flags = IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ },
{ .bitrate = 360,
.hw_value = ATH5K_RATE_CODE_36M,
- .flags = 0 },
+ .flags = IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ },
{ .bitrate = 480,
.hw_value = ATH5K_RATE_CODE_48M,
- .flags = 0 },
+ .flags = IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ },
{ .bitrate = 540,
.hw_value = ATH5K_RATE_CODE_54M,
- .flags = 0 },
+ .flags = IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ },
};

static inline u64 ath5k_extend_tsf(struct ath5k_hw *ah, u32 rstamp)
diff --git a/drivers/net/wireless/ath/ath5k/pcu.c b/drivers/net/wireless/ath/ath5k/pcu.c
index 1f16b42..c60d36a 100644
--- a/drivers/net/wireless/ath/ath5k/pcu.c
+++ b/drivers/net/wireless/ath/ath5k/pcu.c
@@ -144,11 +144,13 @@ ath5k_hw_get_frame_duration(struct ath5k_hw *ah, enum ieee80211_band band,
sifs = AR5K_INIT_SIFS_HALF_RATE;
preamble *= 2;
sym_time *= 2;
+ bitrate = DIV_ROUND_UP(bitrate, 2);
break;
case AR5K_BWMODE_5MHZ:
sifs = AR5K_INIT_SIFS_QUARTER_RATE;
preamble *= 4;
sym_time *= 4;
+ bitrate = DIV_ROUND_UP(bitrate, 4);
break;
default:
sifs = AR5K_INIT_SIFS_DEFAULT_BG;
diff --git a/drivers/net/wireless/ath/ath5k/qcu.c b/drivers/net/wireless/ath/ath5k/qcu.c
index 65fe929..0583c69 100644
--- a/drivers/net/wireless/ath/ath5k/qcu.c
+++ b/drivers/net/wireless/ath/ath5k/qcu.c
@@ -566,9 +566,11 @@ int ath5k_hw_set_ifs_intervals(struct ath5k_hw *ah, unsigned int slot_time)
{
struct ieee80211_channel *channel = ah->ah_current_channel;
enum ieee80211_band band;
+ struct ieee80211_supported_band *sband;
struct ieee80211_rate *rate;
u32 ack_tx_time, eifs, eifs_clock, sifs, sifs_clock;
u32 slot_time_clock = ath5k_hw_htoclock(ah, slot_time);
+ u32 rate_flags, i;

if (slot_time < 6 || slot_time_clock > AR5K_SLOT_TIME_MAX)
return -EINVAL;
@@ -605,7 +607,28 @@ int ath5k_hw_set_ifs_intervals(struct ath5k_hw *ah, unsigned int slot_time)
else
band = IEEE80211_BAND_2GHZ;

- rate = &ah->sbands[band].bitrates[0];
+ switch (ah->ah_bwmode) {
+ case AR5K_BWMODE_5MHZ:
+ rate_flags = IEEE80211_RATE_SUPPORTS_5MHZ;
+ break;
+ case AR5K_BWMODE_10MHZ:
+ rate_flags = IEEE80211_RATE_SUPPORTS_10MHZ;
+ break;
+ default:
+ rate_flags = 0;
+ break;
+ }
+ sband = &ah->sbands[band];
+ rate = NULL;
+ for (i = 0; i < sband->n_bitrates; i++) {
+ if ((rate_flags & sband->bitrates[i].flags) != rate_flags)
+ continue;
+ rate = &sband->bitrates[i];
+ break;
+ }
+ if (WARN_ON(!rate))
+ return -EINVAL;
+
ack_tx_time = ath5k_hw_get_frame_duration(ah, band, 10, rate, false);

/* ack_tx_time includes an SIFS already */
--
1.7.10.4


2013-06-27 16:59:09

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 01/18] nl80211: add scan width to bss and scan request structs

To allow scanning and working with 5 MHz and 10 MHz BSS, extend the
inform bss commands and add wrappers to take 5 and 10 MHz bss into
account.

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
Changes to PATCHv4:
* fix copy/paste error
---
include/net/cfg80211.h | 54 +++++++++++++++++++++++++++++++++++++++---
include/uapi/linux/nl80211.h | 18 ++++++++++++++
net/wireless/nl80211.c | 1 +
net/wireless/scan.c | 31 ++++++++++++++----------
net/wireless/trace.h | 12 ++++++----
5 files changed, 97 insertions(+), 19 deletions(-)

diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index e3a39fc..820cce5 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -1285,6 +1285,7 @@ struct cfg80211_ssid {
* @n_ssids: number of SSIDs
* @channels: channels to scan on.
* @n_channels: total number of channels to scan
+ * @scan_width: channel width for scanning
* @ie: optional information element(s) to add into Probe Request or %NULL
* @ie_len: length of ie in octets
* @flags: bit field of flags controlling operation
@@ -1300,6 +1301,7 @@ struct cfg80211_scan_request {
struct cfg80211_ssid *ssids;
int n_ssids;
u32 n_channels;
+ enum nl80211_bss_scan_width scan_width;
const u8 *ie;
size_t ie_len;
u32 flags;
@@ -1333,6 +1335,7 @@ struct cfg80211_match_set {
* @ssids: SSIDs to scan for (passed in the probe_reqs in active scans)
* @n_ssids: number of SSIDs
* @n_channels: total number of channels to scan
+ * @scan_width: channel width for scanning
* @interval: interval between each scheduled scan cycle
* @ie: optional information element(s) to add into Probe Request or %NULL
* @ie_len: length of ie in octets
@@ -1352,6 +1355,7 @@ struct cfg80211_sched_scan_request {
struct cfg80211_ssid *ssids;
int n_ssids;
u32 n_channels;
+ enum nl80211_bss_scan_width scan_width;
u32 interval;
const u8 *ie;
size_t ie_len;
@@ -1403,6 +1407,7 @@ struct cfg80211_bss_ies {
* for use in scan results and similar.
*
* @channel: channel this BSS is on
+ * @scan_width: width of the control channel
* @bssid: BSSID of the BSS
* @beacon_interval: the beacon interval as from the frame
* @capability: the capability field in host byte order
@@ -1424,6 +1429,7 @@ struct cfg80211_bss_ies {
*/
struct cfg80211_bss {
struct ieee80211_channel *channel;
+ enum nl80211_bss_scan_width scan_width;

const struct cfg80211_bss_ies __rcu *ies;
const struct cfg80211_bss_ies __rcu *beacon_ies;
@@ -3379,10 +3385,11 @@ void cfg80211_sched_scan_results(struct wiphy *wiphy);
void cfg80211_sched_scan_stopped(struct wiphy *wiphy);

/**
- * cfg80211_inform_bss_frame - inform cfg80211 of a received BSS frame
+ * cfg80211_inform_bss_width_frame - inform cfg80211 of a received BSS frame
*
* @wiphy: the wiphy reporting the BSS
* @channel: The channel the frame was received on
+ * @scan_width: width of the control channel
* @mgmt: the management frame (probe response or beacon)
* @len: length of the management frame
* @signal: the signal strength, type depends on the wiphy's signal_type
@@ -3395,16 +3402,29 @@ void cfg80211_sched_scan_stopped(struct wiphy *wiphy);
* Or %NULL on error.
*/
struct cfg80211_bss * __must_check
+cfg80211_inform_bss_width_frame(struct wiphy *wiphy,
+ struct ieee80211_channel *channel,
+ enum nl80211_bss_scan_width scan_width,
+ struct ieee80211_mgmt *mgmt, size_t len,
+ s32 signal, gfp_t gfp);
+
+static inline struct cfg80211_bss * __must_check
cfg80211_inform_bss_frame(struct wiphy *wiphy,
struct ieee80211_channel *channel,
struct ieee80211_mgmt *mgmt, size_t len,
- s32 signal, gfp_t gfp);
+ s32 signal, gfp_t gfp)
+{
+ return cfg80211_inform_bss_width_frame(wiphy, channel,
+ NL80211_BSS_CHAN_WIDTH_20,
+ mgmt, len, signal, gfp);
+}

/**
* cfg80211_inform_bss - inform cfg80211 of a new BSS
*
* @wiphy: the wiphy reporting the BSS
* @channel: The channel the frame was received on
+ * @scan_width: width of the control channel
* @bssid: the BSSID of the BSS
* @tsf: the TSF sent by the peer in the beacon/probe response (or 0)
* @capability: the capability field sent by the peer
@@ -3421,11 +3441,26 @@ cfg80211_inform_bss_frame(struct wiphy *wiphy,
* Or %NULL on error.
*/
struct cfg80211_bss * __must_check
+cfg80211_inform_bss_width(struct wiphy *wiphy,
+ struct ieee80211_channel *channel,
+ enum nl80211_bss_scan_width scan_width,
+ const u8 *bssid, u64 tsf, u16 capability,
+ u16 beacon_interval, const u8 *ie, size_t ielen,
+ s32 signal, gfp_t gfp);
+
+static inline struct cfg80211_bss * __must_check
cfg80211_inform_bss(struct wiphy *wiphy,
struct ieee80211_channel *channel,
const u8 *bssid, u64 tsf, u16 capability,
u16 beacon_interval, const u8 *ie, size_t ielen,
- s32 signal, gfp_t gfp);
+ s32 signal, gfp_t gfp)
+{
+ return cfg80211_inform_bss_width(wiphy, channel,
+ NL80211_BSS_CHAN_WIDTH_20,
+ bssid, tsf, capability,
+ beacon_interval, ie, ielen, signal,
+ gfp);
+}

struct cfg80211_bss *cfg80211_get_bss(struct wiphy *wiphy,
struct ieee80211_channel *channel,
@@ -3471,6 +3506,19 @@ void cfg80211_put_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
*/
void cfg80211_unlink_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);

+static inline enum nl80211_bss_scan_width
+cfg80211_chandef_to_scan_width(const struct cfg80211_chan_def *chandef)
+{
+ switch (chandef->width) {
+ case NL80211_CHAN_WIDTH_5:
+ return NL80211_BSS_CHAN_WIDTH_5;
+ case NL80211_CHAN_WIDTH_10:
+ return NL80211_BSS_CHAN_WIDTH_10;
+ default:
+ return NL80211_BSS_CHAN_WIDTH_20;
+ }
+}
+
/**
* cfg80211_rx_mlme_mgmt - notification of processed MLME management frame
* @dev: network device
diff --git a/include/uapi/linux/nl80211.h b/include/uapi/linux/nl80211.h
index 861e5eb..39609d5 100644
--- a/include/uapi/linux/nl80211.h
+++ b/include/uapi/linux/nl80211.h
@@ -2773,6 +2773,21 @@ enum nl80211_chan_width {
};

/**
+ * enum nl80211_bss_scan_width - control channel width for a BSS
+ *
+ * These values are used with the %NL80211_BSS_CHAN_WIDTH attribute.
+ *
+ * @NL80211_BSS_CHAN_WIDTH_20: control channel is 20 MHz wide or compatible
+ * @NL80211_BSS_CHAN_WIDTH_10: control channel is 10 MHz wide
+ * @NL80211_BSS_CHAN_WIDTH_5: control channel is 5 MHz wide
+ */
+enum nl80211_bss_scan_width {
+ NL80211_BSS_CHAN_WIDTH_20,
+ NL80211_BSS_CHAN_WIDTH_10,
+ NL80211_BSS_CHAN_WIDTH_5,
+};
+
+/**
* enum nl80211_bss - netlink attributes for a BSS
*
* @__NL80211_BSS_INVALID: invalid
@@ -2796,6 +2811,8 @@ enum nl80211_chan_width {
* @NL80211_BSS_BEACON_IES: binary attribute containing the raw information
* elements from a Beacon frame (bin); not present if no Beacon frame has
* yet been received
+ * @NL80211_BSS_CHAN_WIDTH: channel width of the control channel
+ * (u32, enum nl80211_bss_scan_width)
* @__NL80211_BSS_AFTER_LAST: internal
* @NL80211_BSS_MAX: highest BSS attribute
*/
@@ -2812,6 +2829,7 @@ enum nl80211_bss {
NL80211_BSS_STATUS,
NL80211_BSS_SEEN_MS_AGO,
NL80211_BSS_BEACON_IES,
+ NL80211_BSS_CHAN_WIDTH,

/* keep last */
__NL80211_BSS_AFTER_LAST,
diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index 3b7fb5c..ebd889d 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -5619,6 +5619,7 @@ static int nl80211_send_bss(struct sk_buff *msg, struct netlink_callback *cb,
goto nla_put_failure;
if (nla_put_u16(msg, NL80211_BSS_CAPABILITY, res->capability) ||
nla_put_u32(msg, NL80211_BSS_FREQUENCY, res->channel->center_freq) ||
+ nla_put_u32(msg, NL80211_BSS_CHAN_WIDTH, res->scan_width) ||
nla_put_u32(msg, NL80211_BSS_SEEN_MS_AGO,
jiffies_to_msecs(jiffies - intbss->ts)))
goto nla_put_failure;
diff --git a/net/wireless/scan.c b/net/wireless/scan.c
index dd01b58..cbe4d27 100644
--- a/net/wireless/scan.c
+++ b/net/wireless/scan.c
@@ -650,6 +650,8 @@ static bool cfg80211_combine_bsses(struct cfg80211_registered_device *dev,
continue;
if (bss->pub.channel != new->pub.channel)
continue;
+ if (bss->pub.scan_width != new->pub.scan_width)
+ continue;
if (rcu_access_pointer(bss->pub.beacon_ies))
continue;
ies = rcu_access_pointer(bss->pub.ies);
@@ -867,11 +869,12 @@ cfg80211_get_bss_channel(struct wiphy *wiphy, const u8 *ie, size_t ielen,
}

struct cfg80211_bss*
-cfg80211_inform_bss(struct wiphy *wiphy,
- struct ieee80211_channel *channel,
- const u8 *bssid, u64 tsf, u16 capability,
- u16 beacon_interval, const u8 *ie, size_t ielen,
- s32 signal, gfp_t gfp)
+cfg80211_inform_bss_width(struct wiphy *wiphy,
+ struct ieee80211_channel *channel,
+ enum nl80211_bss_scan_width scan_width,
+ const u8 *bssid, u64 tsf, u16 capability,
+ u16 beacon_interval, const u8 *ie, size_t ielen,
+ s32 signal, gfp_t gfp)
{
struct cfg80211_bss_ies *ies;
struct cfg80211_internal_bss tmp = {}, *res;
@@ -889,6 +892,7 @@ cfg80211_inform_bss(struct wiphy *wiphy,

memcpy(tmp.pub.bssid, bssid, ETH_ALEN);
tmp.pub.channel = channel;
+ tmp.pub.scan_width = scan_width;
tmp.pub.signal = signal;
tmp.pub.beacon_interval = beacon_interval;
tmp.pub.capability = capability;
@@ -921,13 +925,14 @@ cfg80211_inform_bss(struct wiphy *wiphy,
/* cfg80211_bss_update gives us a referenced result */
return &res->pub;
}
-EXPORT_SYMBOL(cfg80211_inform_bss);
+EXPORT_SYMBOL(cfg80211_inform_bss_width);

struct cfg80211_bss *
-cfg80211_inform_bss_frame(struct wiphy *wiphy,
- struct ieee80211_channel *channel,
- struct ieee80211_mgmt *mgmt, size_t len,
- s32 signal, gfp_t gfp)
+cfg80211_inform_bss_width_frame(struct wiphy *wiphy,
+ struct ieee80211_channel *channel,
+ enum nl80211_bss_scan_width scan_width,
+ struct ieee80211_mgmt *mgmt, size_t len,
+ s32 signal, gfp_t gfp)
{
struct cfg80211_internal_bss tmp = {}, *res;
struct cfg80211_bss_ies *ies;
@@ -937,7 +942,8 @@ cfg80211_inform_bss_frame(struct wiphy *wiphy,
BUILD_BUG_ON(offsetof(struct ieee80211_mgmt, u.probe_resp.variable) !=
offsetof(struct ieee80211_mgmt, u.beacon.variable));

- trace_cfg80211_inform_bss_frame(wiphy, channel, mgmt, len, signal);
+ trace_cfg80211_inform_bss_width_frame(wiphy, channel, scan_width, mgmt,
+ len, signal);

if (WARN_ON(!mgmt))
return NULL;
@@ -972,6 +978,7 @@ cfg80211_inform_bss_frame(struct wiphy *wiphy,

memcpy(tmp.pub.bssid, mgmt->bssid, ETH_ALEN);
tmp.pub.channel = channel;
+ tmp.pub.scan_width = scan_width;
tmp.pub.signal = signal;
tmp.pub.beacon_interval = le16_to_cpu(mgmt->u.probe_resp.beacon_int);
tmp.pub.capability = le16_to_cpu(mgmt->u.probe_resp.capab_info);
@@ -987,7 +994,7 @@ cfg80211_inform_bss_frame(struct wiphy *wiphy,
/* cfg80211_bss_update gives us a referenced result */
return &res->pub;
}
-EXPORT_SYMBOL(cfg80211_inform_bss_frame);
+EXPORT_SYMBOL(cfg80211_inform_bss_width_frame);

void cfg80211_ref_bss(struct wiphy *wiphy, struct cfg80211_bss *pub)
{
diff --git a/net/wireless/trace.h b/net/wireless/trace.h
index e1534baf..09af6eb 100644
--- a/net/wireless/trace.h
+++ b/net/wireless/trace.h
@@ -2391,26 +2391,30 @@ TRACE_EVENT(cfg80211_get_bss,
__entry->capa_mask, __entry->capa_val)
);

-TRACE_EVENT(cfg80211_inform_bss_frame,
+TRACE_EVENT(cfg80211_inform_bss_width_frame,
TP_PROTO(struct wiphy *wiphy, struct ieee80211_channel *channel,
+ enum nl80211_bss_scan_width scan_width,
struct ieee80211_mgmt *mgmt, size_t len,
s32 signal),
- TP_ARGS(wiphy, channel, mgmt, len, signal),
+ TP_ARGS(wiphy, channel, scan_width, mgmt, len, signal),
TP_STRUCT__entry(
WIPHY_ENTRY
CHAN_ENTRY
+ __field(enum nl80211_bss_scan_width, scan_width)
__dynamic_array(u8, mgmt, len)
__field(s32, signal)
),
TP_fast_assign(
WIPHY_ASSIGN;
CHAN_ASSIGN(channel);
+ __entry->scan_width = scan_width;
if (mgmt)
memcpy(__get_dynamic_array(mgmt), mgmt, len);
__entry->signal = signal;
),
- TP_printk(WIPHY_PR_FMT ", " CHAN_PR_FMT "signal: %d",
- WIPHY_PR_ARG, CHAN_PR_ARG, __entry->signal)
+ TP_printk(WIPHY_PR_FMT ", " CHAN_PR_FMT "(scan_width: %d) signal: %d",
+ WIPHY_PR_ARG, CHAN_PR_ARG, __entry->scan_width,
+ __entry->signal)
);

DECLARE_EVENT_CLASS(cfg80211_bss_evt,
--
1.7.10.4


2013-06-27 16:59:18

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 15/18] ath9k: announce that ath9k supports 5/10 MHz

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
drivers/net/wireless/ath/ath9k/init.c | 1 +
1 file changed, 1 insertion(+)

diff --git a/drivers/net/wireless/ath/ath9k/init.c b/drivers/net/wireless/ath/ath9k/init.c
index 96b0d29..f6ae49f 100644
--- a/drivers/net/wireless/ath/ath9k/init.c
+++ b/drivers/net/wireless/ath/ath9k/init.c
@@ -844,6 +844,7 @@ void ath9k_set_hw_capab(struct ath_softc *sc, struct ieee80211_hw *hw)
hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN;
hw->wiphy->flags |= WIPHY_FLAG_SUPPORTS_TDLS;
hw->wiphy->flags |= WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL;
+ hw->wiphy->flags |= WIPHY_FLAG_SUPPORTS_5_10_MHZ;

#ifdef CONFIG_PM_SLEEP
if ((ah->caps.hw_caps & ATH9K_HW_WOW_DEVICE_CAPABLE) &&
--
1.7.10.4


2013-06-27 16:59:18

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 16/18] ath5k: report 5/10 MHz channels

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
drivers/net/wireless/ath/ath5k/base.c | 10 ++++++++++
1 file changed, 10 insertions(+)

diff --git a/drivers/net/wireless/ath/ath5k/base.c b/drivers/net/wireless/ath/ath5k/base.c
index ce67ab7..260a6fc 100644
--- a/drivers/net/wireless/ath/ath5k/base.c
+++ b/drivers/net/wireless/ath/ath5k/base.c
@@ -1400,6 +1400,16 @@ ath5k_receive_frame(struct ath5k_hw *ah, struct sk_buff *skb,

rxs->rate_idx = ath5k_hw_to_driver_rix(ah, rs->rs_rate);
rxs->flag |= ath5k_rx_decrypted(ah, skb, rs);
+ switch (ah->ah_bwmode) {
+ case AR5K_BWMODE_5MHZ:
+ rxs->flag |= RX_FLAG_5MHZ;
+ break;
+ case AR5K_BWMODE_10MHZ:
+ rxs->flag |= RX_FLAG_10MHZ;
+ break;
+ default:
+ break;
+ }

if (rxs->rate_idx >= 0 && rs->rs_rate ==
ah->sbands[ah->curchan->band].bitrates[rxs->rate_idx].hw_value_short)
--
1.7.10.4


2013-06-27 16:59:17

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 06/18] cfg80211/mac80211: use reduced txpower for 5 and 10 MHz

Some regulations (like germany, but also FCC) express their transmission
power limit in dBm/MHz or mW/MHz. To cope with that and be on the safe
side, reduce the maximum power to half (10 MHz) or quarter (5 MHz)
when operating on these reduced bandwidth channels.

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>

---
Changes to PATCHv3:
* consider max_reg_power, max_power might contain the hardware limit
---
include/net/cfg80211.h | 27 +++++++++++++++++++++++++++
net/mac80211/iface.c | 2 +-
net/mac80211/main.c | 2 +-
net/mac80211/mlme.c | 3 ++-
4 files changed, 31 insertions(+), 3 deletions(-)

diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 83d52dc..69be9fe 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -461,6 +461,33 @@ ieee80211_chandef_rate_flags(struct cfg80211_chan_def *chandef)
}

/**
+ * ieee80211_chandef_max_power - maximum transmission power for the chandef
+ *
+ * In some regulations, the transmit power may depend on the configured channel
+ * bandwidth which may be defined as dBm/MHz. This function returns the actual
+ * max_power for non-standard (20 MHz) channels.
+ *
+ * @chandef: channel definition for the channel
+ *
+ * Returns: maximum allowed transmission power in dBm for the chandef
+ */
+static inline int
+ieee80211_chandef_max_power(struct cfg80211_chan_def *chandef)
+{
+ switch (chandef->width) {
+ case NL80211_CHAN_WIDTH_5:
+ return min(chandef->chan->max_reg_power - 6,
+ chandef->chan->max_power);
+ case NL80211_CHAN_WIDTH_10:
+ return min(chandef->chan->max_reg_power - 3,
+ chandef->chan->max_power);
+ default:
+ break;
+ }
+ return chandef->chan->max_power;
+}
+
+/**
* enum survey_info_flags - survey information flags
*
* @SURVEY_INFO_NOISE_DBM: noise (in dBm) was filled in
diff --git a/net/mac80211/iface.c b/net/mac80211/iface.c
index a2a8250..093c34a 100644
--- a/net/mac80211/iface.c
+++ b/net/mac80211/iface.c
@@ -54,7 +54,7 @@ bool __ieee80211_recalc_txpower(struct ieee80211_sub_if_data *sdata)
return false;
}

- power = chanctx_conf->def.chan->max_power;
+ power = ieee80211_chandef_max_power(&chanctx_conf->def);
rcu_read_unlock();

if (sdata->user_power_level != IEEE80211_UNSET_POWER_LEVEL)
diff --git a/net/mac80211/main.c b/net/mac80211/main.c
index 626c83c..a1d51af 100644
--- a/net/mac80211/main.c
+++ b/net/mac80211/main.c
@@ -151,7 +151,7 @@ static u32 ieee80211_hw_conf_chan(struct ieee80211_local *local)
changed |= IEEE80211_CONF_CHANGE_SMPS;
}

- power = chandef.chan->max_power;
+ power = ieee80211_chandef_max_power(&chandef);

rcu_read_lock();
list_for_each_entry_rcu(sdata, &local->interfaces, list) {
diff --git a/net/mac80211/mlme.c b/net/mac80211/mlme.c
index eb45c7e..63f8059 100644
--- a/net/mac80211/mlme.c
+++ b/net/mac80211/mlme.c
@@ -747,7 +747,8 @@ static void ieee80211_send_assoc(struct ieee80211_sub_if_data *sdata)
*pos++ = WLAN_EID_PWR_CAPABILITY;
*pos++ = 2;
*pos++ = 0; /* min tx power */
- *pos++ = chan->max_power; /* max tx power */
+ /* max tx power */
+ *pos++ = ieee80211_chandef_max_power(&chanctx_conf->def);

/* 2. supported channels */
/* TODO: get this in reg domain format */
--
1.7.10.4


2013-06-27 16:59:18

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 12/18] ath9k: use chandef instead of channel_type

To enable support for 5/10 MHz, some internal functions must be
converted from using the (old) channel_type to chandef. This is a good
chance to change all remaining occurences.

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
drivers/net/wireless/ath/ath9k/common.c | 67 +++++++++++++++----------
drivers/net/wireless/ath/ath9k/common.h | 3 +-
drivers/net/wireless/ath/ath9k/htc_drv_main.c | 5 +-
drivers/net/wireless/ath/ath9k/init.c | 4 +-
drivers/net/wireless/ath/ath9k/main.c | 8 ++-
drivers/net/wireless/ath/ath9k/rc.c | 4 +-
6 files changed, 51 insertions(+), 40 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/common.c b/drivers/net/wireless/ath/ath9k/common.c
index 344fdde..d3063c2 100644
--- a/drivers/net/wireless/ath/ath9k/common.c
+++ b/drivers/net/wireless/ath/ath9k/common.c
@@ -49,37 +49,40 @@ int ath9k_cmn_get_hw_crypto_keytype(struct sk_buff *skb)
}
EXPORT_SYMBOL(ath9k_cmn_get_hw_crypto_keytype);

-static u32 ath9k_get_extchanmode(struct ieee80211_channel *chan,
- enum nl80211_channel_type channel_type)
+static u32 ath9k_get_extchanmode(struct cfg80211_chan_def *chandef)
{
u32 chanmode = 0;

- switch (chan->band) {
+ switch (chandef->chan->band) {
case IEEE80211_BAND_2GHZ:
- switch (channel_type) {
- case NL80211_CHAN_NO_HT:
- case NL80211_CHAN_HT20:
+ switch (chandef->width) {
+ case NL80211_CHAN_WIDTH_20_NOHT:
+ case NL80211_CHAN_WIDTH_20:
chanmode = CHANNEL_G_HT20;
break;
- case NL80211_CHAN_HT40PLUS:
- chanmode = CHANNEL_G_HT40PLUS;
+ case NL80211_CHAN_WIDTH_40:
+ if (chandef->center_freq1 > chandef->chan->center_freq)
+ chanmode = CHANNEL_G_HT40PLUS;
+ else
+ chanmode = CHANNEL_G_HT40MINUS;
break;
- case NL80211_CHAN_HT40MINUS:
- chanmode = CHANNEL_G_HT40MINUS;
+ default:
break;
}
break;
case IEEE80211_BAND_5GHZ:
- switch (channel_type) {
- case NL80211_CHAN_NO_HT:
- case NL80211_CHAN_HT20:
+ switch (chandef->width) {
+ case NL80211_CHAN_WIDTH_20_NOHT:
+ case NL80211_CHAN_WIDTH_20:
chanmode = CHANNEL_A_HT20;
break;
- case NL80211_CHAN_HT40PLUS:
- chanmode = CHANNEL_A_HT40PLUS;
+ case NL80211_CHAN_WIDTH_40:
+ if (chandef->center_freq1 > chandef->chan->center_freq)
+ chanmode = CHANNEL_A_HT40PLUS;
+ else
+ chanmode = CHANNEL_A_HT40MINUS;
break;
- case NL80211_CHAN_HT40MINUS:
- chanmode = CHANNEL_A_HT40MINUS;
+ default:
break;
}
break;
@@ -94,13 +97,12 @@ static u32 ath9k_get_extchanmode(struct ieee80211_channel *chan,
* Update internal channel flags.
*/
void ath9k_cmn_update_ichannel(struct ath9k_channel *ichan,
- struct ieee80211_channel *chan,
- enum nl80211_channel_type channel_type)
+ struct cfg80211_chan_def *chandef)
{
- ichan->channel = chan->center_freq;
- ichan->chan = chan;
+ ichan->channel = chandef->chan->center_freq;
+ ichan->chan = chandef->chan;

- if (chan->band == IEEE80211_BAND_2GHZ) {
+ if (chandef->chan->band == IEEE80211_BAND_2GHZ) {
ichan->chanmode = CHANNEL_G;
ichan->channelFlags = CHANNEL_2GHZ | CHANNEL_OFDM;
} else {
@@ -108,8 +110,22 @@ void ath9k_cmn_update_ichannel(struct ath9k_channel *ichan,
ichan->channelFlags = CHANNEL_5GHZ | CHANNEL_OFDM;
}

- if (channel_type != NL80211_CHAN_NO_HT)
- ichan->chanmode = ath9k_get_extchanmode(chan, channel_type);
+ switch (chandef->width) {
+ case NL80211_CHAN_WIDTH_5:
+ ichan->channelFlags |= CHANNEL_QUARTER;
+ break;
+ case NL80211_CHAN_WIDTH_10:
+ ichan->channelFlags |= CHANNEL_HALF;
+ break;
+ case NL80211_CHAN_WIDTH_20_NOHT:
+ break;
+ case NL80211_CHAN_WIDTH_20:
+ case NL80211_CHAN_WIDTH_40:
+ ichan->chanmode = ath9k_get_extchanmode(chandef);
+ break;
+ default:
+ WARN_ON(1);
+ }
}
EXPORT_SYMBOL(ath9k_cmn_update_ichannel);

@@ -125,8 +141,7 @@ struct ath9k_channel *ath9k_cmn_get_curchannel(struct ieee80211_hw *hw,

chan_idx = curchan->hw_value;
channel = &ah->channels[chan_idx];
- ath9k_cmn_update_ichannel(channel, curchan,
- cfg80211_get_chandef_type(&hw->conf.chandef));
+ ath9k_cmn_update_ichannel(channel, &hw->conf.chandef);

return channel;
}
diff --git a/drivers/net/wireless/ath/ath9k/common.h b/drivers/net/wireless/ath/ath9k/common.h
index 207d069..e039bcb 100644
--- a/drivers/net/wireless/ath/ath9k/common.h
+++ b/drivers/net/wireless/ath/ath9k/common.h
@@ -44,8 +44,7 @@

int ath9k_cmn_get_hw_crypto_keytype(struct sk_buff *skb);
void ath9k_cmn_update_ichannel(struct ath9k_channel *ichan,
- struct ieee80211_channel *chan,
- enum nl80211_channel_type channel_type);
+ struct cfg80211_chan_def *chandef);
struct ath9k_channel *ath9k_cmn_get_curchannel(struct ieee80211_hw *hw,
struct ath_hw *ah);
int ath9k_cmn_count_streams(unsigned int chainmask, int max);
diff --git a/drivers/net/wireless/ath/ath9k/htc_drv_main.c b/drivers/net/wireless/ath/ath9k/htc_drv_main.c
index fba6ea7..87b3429 100644
--- a/drivers/net/wireless/ath/ath9k/htc_drv_main.c
+++ b/drivers/net/wireless/ath/ath9k/htc_drv_main.c
@@ -1203,16 +1203,13 @@ static int ath9k_htc_config(struct ieee80211_hw *hw, u32 changed)

if ((changed & IEEE80211_CONF_CHANGE_CHANNEL) || chip_reset) {
struct ieee80211_channel *curchan = hw->conf.chandef.chan;
- enum nl80211_channel_type channel_type =
- cfg80211_get_chandef_type(&hw->conf.chandef);
int pos = curchan->hw_value;

ath_dbg(common, CONFIG, "Set channel: %d MHz\n",
curchan->center_freq);

ath9k_cmn_update_ichannel(&priv->ah->channels[pos],
- hw->conf.chandef.chan,
- channel_type);
+ &hw->conf.chandef);

if (ath9k_htc_set_channel(priv, hw, &priv->ah->channels[pos]) < 0) {
ath_err(common, "Unable to set channel\n");
diff --git a/drivers/net/wireless/ath/ath9k/init.c b/drivers/net/wireless/ath/ath9k/init.c
index 1e555d8..d0d3d2a 100644
--- a/drivers/net/wireless/ath/ath9k/init.c
+++ b/drivers/net/wireless/ath/ath9k/init.c
@@ -710,13 +710,15 @@ static void ath9k_init_band_txpower(struct ath_softc *sc, int band)
struct ieee80211_supported_band *sband;
struct ieee80211_channel *chan;
struct ath_hw *ah = sc->sc_ah;
+ struct cfg80211_chan_def chandef;
int i;

sband = &sc->sbands[band];
for (i = 0; i < sband->n_channels; i++) {
chan = &sband->channels[i];
ah->curchan = &ah->channels[chan->hw_value];
- ath9k_cmn_update_ichannel(ah->curchan, chan, NL80211_CHAN_HT20);
+ cfg80211_chandef_create(&chandef, chan, NL80211_CHAN_HT20);
+ ath9k_cmn_update_ichannel(ah->curchan, &chandef);
ath9k_hw_set_txpowerlimit(ah, MAX_RATE_POWER, true);
}
}
diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c
index 1737a3e..ff91f4a 100644
--- a/drivers/net/wireless/ath/ath9k/main.c
+++ b/drivers/net/wireless/ath/ath9k/main.c
@@ -1193,8 +1193,6 @@ static int ath9k_config(struct ieee80211_hw *hw, u32 changed)

if ((changed & IEEE80211_CONF_CHANGE_CHANNEL) || reset_channel) {
struct ieee80211_channel *curchan = hw->conf.chandef.chan;
- enum nl80211_channel_type channel_type =
- cfg80211_get_chandef_type(&conf->chandef);
int pos = curchan->hw_value;
int old_pos = -1;
unsigned long flags;
@@ -1202,8 +1200,8 @@ static int ath9k_config(struct ieee80211_hw *hw, u32 changed)
if (ah->curchan)
old_pos = ah->curchan - &ah->channels[0];

- ath_dbg(common, CONFIG, "Set channel: %d MHz type: %d\n",
- curchan->center_freq, channel_type);
+ ath_dbg(common, CONFIG, "Set channel: %d MHz width: %d\n",
+ curchan->center_freq, hw->conf.chandef.width);

/* update survey stats for the old channel before switching */
spin_lock_irqsave(&common->cc_lock, flags);
@@ -1211,7 +1209,7 @@ static int ath9k_config(struct ieee80211_hw *hw, u32 changed)
spin_unlock_irqrestore(&common->cc_lock, flags);

ath9k_cmn_update_ichannel(&sc->sc_ah->channels[pos],
- curchan, channel_type);
+ &conf->chandef);

/*
* If the operating channel changes, change the survey in-use flags
diff --git a/drivers/net/wireless/ath/ath9k/rc.c b/drivers/net/wireless/ath/ath9k/rc.c
index a3c4ca0..e41f563 100644
--- a/drivers/net/wireless/ath/ath9k/rc.c
+++ b/drivers/net/wireless/ath/ath9k/rc.c
@@ -1326,8 +1326,8 @@ static void ath_rate_update(void *priv, struct ieee80211_supported_band *sband,
ath_rc_init(sc, priv_sta);

ath_dbg(ath9k_hw_common(sc->sc_ah), CONFIG,
- "Operating HT Bandwidth changed to: %d\n",
- cfg80211_get_chandef_type(&sc->hw->conf.chandef));
+ "Operating Bandwidth changed to: %d\n",
+ &sc->hw->conf.chandef->width);
}
}

--
1.7.10.4


2013-06-27 16:59:14

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 05/18] cfg80211/mac80211: get mandatory rates based on scan width

Mandatory rates for 5 and 10 MHz are different from the rates used for
20 MHz in 2.4 GHz mode, as they use OFDM only.

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>

---
Changes to PATCHv4:
* it is now based on scan_width instead of rate flags
---
include/net/cfg80211.h | 4 +++-
net/mac80211/ibss.c | 19 +++++++++++++++----
net/wireless/mesh.c | 5 ++++-
net/wireless/util.c | 14 ++++++++++----
4 files changed, 32 insertions(+), 10 deletions(-)

diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 820cce5..83d52dc 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -3069,11 +3069,13 @@ ieee80211_get_response_rate(struct ieee80211_supported_band *sband,
/**
* ieee80211_mandatory_rates - get mandatory rates for a given band
* @sband: the band to look for rates in
+ * @scan_width: width of the control channel
*
* This function returns a bitmap of the mandatory rates for the given
* band, bits are set according to the rate position in the bitrates array.
*/
-u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband);
+u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband,
+ enum nl80211_bss_scan_width scan_width);

/*
* Radiotap parsing functions -- for controlled injection support
diff --git a/net/mac80211/ibss.c b/net/mac80211/ibss.c
index fa91df8..d0c27dc 100644
--- a/net/mac80211/ibss.c
+++ b/net/mac80211/ibss.c
@@ -376,6 +376,7 @@ ieee80211_ibss_add_sta(struct ieee80211_sub_if_data *sdata,
struct sta_info *sta;
struct ieee80211_chanctx_conf *chanctx_conf;
struct ieee80211_supported_band *sband;
+ enum nl80211_bss_scan_width scan_width;
int band;

/*
@@ -404,6 +405,7 @@ ieee80211_ibss_add_sta(struct ieee80211_sub_if_data *sdata,
if (WARN_ON_ONCE(!chanctx_conf))
return NULL;
band = chanctx_conf->def.chan->band;
+ scan_width = cfg80211_chandef_to_scan_width(&chanctx_conf->def);
rcu_read_unlock();

sta = sta_info_alloc(sdata, addr, GFP_KERNEL);
@@ -417,7 +419,7 @@ ieee80211_ibss_add_sta(struct ieee80211_sub_if_data *sdata,
/* make sure mandatory rates are always added */
sband = local->hw.wiphy->bands[band];
sta->sta.supp_rates[band] = supp_rates |
- ieee80211_mandatory_rates(sband);
+ ieee80211_mandatory_rates(sband, scan_width);

return ieee80211_ibss_finish_sta(sta, auth);
}
@@ -499,6 +501,7 @@ static void ieee80211_rx_bss_info(struct ieee80211_sub_if_data *sdata,
u64 beacon_timestamp, rx_timestamp;
u32 supp_rates = 0;
enum ieee80211_band band = rx_status->band;
+ enum nl80211_bss_scan_width scan_width;
struct ieee80211_supported_band *sband = local->hw.wiphy->bands[band];
bool rates_updated = false;

@@ -527,9 +530,15 @@ static void ieee80211_rx_bss_info(struct ieee80211_sub_if_data *sdata,

prev_rates = sta->sta.supp_rates[band];
/* make sure mandatory rates are always added */
+ scan_width = NL80211_BSS_CHAN_WIDTH_20;
+ if (rx_status->flag & RX_FLAG_5MHZ)
+ scan_width = NL80211_BSS_CHAN_WIDTH_5;
+ if (rx_status->flag & RX_FLAG_10MHZ)
+ scan_width = NL80211_BSS_CHAN_WIDTH_10;
+
sta->sta.supp_rates[band] = supp_rates |
- ieee80211_mandatory_rates(sband);
-
+ ieee80211_mandatory_rates(sband,
+ scan_width);
if (sta->sta.supp_rates[band] != prev_rates) {
ibss_dbg(sdata,
"updated supp_rates set for %pM based on beacon/probe_resp (0x%x -> 0x%x)\n",
@@ -663,6 +672,7 @@ void ieee80211_ibss_rx_no_sta(struct ieee80211_sub_if_data *sdata,
struct sta_info *sta;
struct ieee80211_chanctx_conf *chanctx_conf;
struct ieee80211_supported_band *sband;
+ enum nl80211_bss_scan_width scan_width;
int band;

/*
@@ -688,6 +698,7 @@ void ieee80211_ibss_rx_no_sta(struct ieee80211_sub_if_data *sdata,
return;
}
band = chanctx_conf->def.chan->band;
+ scan_width = cfg80211_chandef_to_scan_width(&chanctx_conf->def);
rcu_read_unlock();

sta = sta_info_alloc(sdata, addr, GFP_ATOMIC);
@@ -699,7 +710,7 @@ void ieee80211_ibss_rx_no_sta(struct ieee80211_sub_if_data *sdata,
/* make sure mandatory rates are always added */
sband = local->hw.wiphy->bands[band];
sta->sta.supp_rates[band] = supp_rates |
- ieee80211_mandatory_rates(sband);
+ ieee80211_mandatory_rates(sband, scan_width);

spin_lock(&ifibss->incomplete_lock);
list_add(&sta->list, &ifibss->incomplete_stations);
diff --git a/net/wireless/mesh.c b/net/wireless/mesh.c
index 30c4920..0553fd4 100644
--- a/net/wireless/mesh.c
+++ b/net/wireless/mesh.c
@@ -167,9 +167,12 @@ int __cfg80211_join_mesh(struct cfg80211_registered_device *rdev,
* basic rates
*/
if (!setup->basic_rates) {
+ enum nl80211_bss_scan_width scan_width;
struct ieee80211_supported_band *sband =
rdev->wiphy.bands[setup->chandef.chan->band];
- setup->basic_rates = ieee80211_mandatory_rates(sband);
+ scan_width = cfg80211_chandef_to_scan_width(&setup->chandef);
+ setup->basic_rates = ieee80211_mandatory_rates(sband,
+ scan_width);
}

if (!cfg80211_reg_can_beacon(&rdev->wiphy, &setup->chandef))
diff --git a/net/wireless/util.c b/net/wireless/util.c
index 74458b7..ce090c1 100644
--- a/net/wireless/util.c
+++ b/net/wireless/util.c
@@ -33,7 +33,8 @@ ieee80211_get_response_rate(struct ieee80211_supported_band *sband,
}
EXPORT_SYMBOL(ieee80211_get_response_rate);

-u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband)
+u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband,
+ enum nl80211_bss_scan_width scan_width)
{
struct ieee80211_rate *bitrates;
u32 mandatory_rates = 0;
@@ -43,10 +44,15 @@ u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband)
if (WARN_ON(!sband))
return 1;

- if (sband->band == IEEE80211_BAND_2GHZ)
- mandatory_flag = IEEE80211_RATE_MANDATORY_B;
- else
+ if (sband->band == IEEE80211_BAND_2GHZ) {
+ if (scan_width == NL80211_BSS_CHAN_WIDTH_5 ||
+ scan_width == NL80211_BSS_CHAN_WIDTH_10)
+ mandatory_flag = IEEE80211_RATE_MANDATORY_G;
+ else
+ mandatory_flag = IEEE80211_RATE_MANDATORY_B;
+ } else {
mandatory_flag = IEEE80211_RATE_MANDATORY_A;
+ }

bitrates = sband->bitrates;
for (i = 0; i < sband->n_bitrates; i++)
--
1.7.10.4


2013-06-27 16:59:16

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 04/18] mac80211: select and adjust bitrates according to channel mode

The various components accessing the bitrates table must use consider
the used channel bandwidth to select only available rates or calculate
the bitrate correctly.

There are some rates in reduced bandwidth modes which can't be
represented as multiples of 500kbps, like 2.25 MBit/s in 5 MHz mode. The
standard suggests to round up to the next multiple of 500kbps, just do
that in mac80211 as well.

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
Chagnes to PATCHv4:
* change divisor to shift to avoid unnecesary integer divisions

Changes to PATCHv3:
* get divisor from flags in ieee80211_calculate_rx_timestamp
* use sdata instead of local for sta_get_rates
* don't access hw.conf (this would break chandef drivers)
* put similar bitrate parsing functions into ieee80211_parse_bitrates()
---
net/mac80211/cfg.c | 48 ++++++-------
net/mac80211/ibss.c | 81 ++++++++++++++++------
net/mac80211/ieee80211_i.h | 9 ++-
net/mac80211/mesh.c | 2 +-
net/mac80211/mesh_plink.c | 2 +-
net/mac80211/mlme.c | 95 ++++++++++++++------------
net/mac80211/rate.c | 50 +++++++-------
net/mac80211/rx.c | 7 +-
net/mac80211/scan.c | 27 +++++++-
net/mac80211/status.c | 17 +++--
net/mac80211/tx.c | 21 ++++--
net/mac80211/util.c | 159 +++++++++++++++++++++++++++++++++++---------
12 files changed, 357 insertions(+), 161 deletions(-)

diff --git a/net/mac80211/cfg.c b/net/mac80211/cfg.c
index 082f270..7c9b254 100644
--- a/net/mac80211/cfg.c
+++ b/net/mac80211/cfg.c
@@ -395,9 +395,13 @@ void sta_set_rate_info_tx(struct sta_info *sta,
rinfo->nss = ieee80211_rate_get_vht_nss(rate);
} else {
struct ieee80211_supported_band *sband;
+ int shift = ieee80211_vif_get_shift(&sta->sdata->vif);
+ u16 brate;
+
sband = sta->local->hw.wiphy->bands[
ieee80211_get_sdata_band(sta->sdata)];
- rinfo->legacy = sband->bitrates[rate->idx].bitrate;
+ brate = sband->bitrates[rate->idx].bitrate;
+ rinfo->legacy = DIV_ROUND_UP(brate, 1 << shift);
}
if (rate->flags & IEEE80211_TX_RC_40_MHZ_WIDTH)
rinfo->flags |= RATE_INFO_FLAGS_40_MHZ_WIDTH;
@@ -422,11 +426,13 @@ void sta_set_rate_info_rx(struct sta_info *sta, struct rate_info *rinfo)
rinfo->mcs = sta->last_rx_rate_idx;
} else {
struct ieee80211_supported_band *sband;
+ int shift = ieee80211_vif_get_shift(&sta->sdata->vif);
+ u16 brate;

sband = sta->local->hw.wiphy->bands[
ieee80211_get_sdata_band(sta->sdata)];
- rinfo->legacy =
- sband->bitrates[sta->last_rx_rate_idx].bitrate;
+ brate = sband->bitrates[sta->last_rx_rate_idx].bitrate;
+ rinfo->legacy = DIV_ROUND_UP(brate, 1 << shift);
}

if (sta->last_rx_rate_flag & RX_FLAG_40MHZ)
@@ -1185,13 +1191,14 @@ static int sta_apply_auth_flags(struct ieee80211_local *local,
return 0;
}

+
+
+
static int sta_apply_parameters(struct ieee80211_local *local,
struct sta_info *sta,
struct station_parameters *params)
{
int ret = 0;
- u32 rates;
- int i, j;
struct ieee80211_supported_band *sband;
struct ieee80211_sub_if_data *sdata = sta->sdata;
enum ieee80211_band band = ieee80211_get_sdata_band(sdata);
@@ -1284,16 +1291,10 @@ static int sta_apply_parameters(struct ieee80211_local *local,
sta->listen_interval = params->listen_interval;

if (params->supported_rates) {
- rates = 0;
-
- for (i = 0; i < params->supported_rates_len; i++) {
- int rate = (params->supported_rates[i] & 0x7f) * 5;
- for (j = 0; j < sband->n_bitrates; j++) {
- if (sband->bitrates[j].bitrate == rate)
- rates |= BIT(j);
- }
- }
- sta->sta.supp_rates[band] = rates;
+ ieee80211_parse_bitrates(&sdata->vif.bss_conf.chandef,
+ sband, params->supported_rates,
+ params->supported_rates_len,
+ &sta->sta.supp_rates[band]);
}

if (params->ht_capa)
@@ -1956,18 +1957,11 @@ static int ieee80211_change_bss(struct wiphy *wiphy,
}

if (params->basic_rates) {
- int i, j;
- u32 rates = 0;
- struct ieee80211_supported_band *sband = wiphy->bands[band];
-
- for (i = 0; i < params->basic_rates_len; i++) {
- int rate = (params->basic_rates[i] & 0x7f) * 5;
- for (j = 0; j < sband->n_bitrates; j++) {
- if (sband->bitrates[j].bitrate == rate)
- rates |= BIT(j);
- }
- }
- sdata->vif.bss_conf.basic_rates = rates;
+ ieee80211_parse_bitrates(&sdata->vif.bss_conf.chandef,
+ wiphy->bands[band],
+ params->basic_rates,
+ params->basic_rates_len,
+ &sdata->vif.bss_conf.basic_rates);
changed |= BSS_CHANGED_BASIC_RATES;
}

diff --git a/net/mac80211/ibss.c b/net/mac80211/ibss.c
index eaacfd2..fa91df8 100644
--- a/net/mac80211/ibss.c
+++ b/net/mac80211/ibss.c
@@ -43,16 +43,17 @@ static void __ieee80211_sta_join_ibss(struct ieee80211_sub_if_data *sdata,
{
struct ieee80211_if_ibss *ifibss = &sdata->u.ibss;
struct ieee80211_local *local = sdata->local;
- int rates, i;
+ int rates_n = 0, i, ri;
struct ieee80211_mgmt *mgmt;
u8 *pos;
struct ieee80211_supported_band *sband;
struct cfg80211_bss *bss;
- u32 bss_change;
+ u32 bss_change, rate_flags, rates = 0, rates_added = 0;
u8 supp_rates[IEEE80211_MAX_SUPP_RATES];
struct cfg80211_chan_def chandef;
struct beacon_data *presp;
int frame_len;
+ int shift;

sdata_assert_lock(sdata);

@@ -99,6 +100,7 @@ static void __ieee80211_sta_join_ibss(struct ieee80211_sub_if_data *sdata,
memcpy(ifibss->bssid, bssid, ETH_ALEN);

sband = local->hw.wiphy->bands[chan->band];
+ shift = ieee80211_vif_get_shift(&sdata->vif);

/* Build IBSS probe response */
frame_len = sizeof(struct ieee80211_hdr_3addr) +
@@ -134,15 +136,29 @@ static void __ieee80211_sta_join_ibss(struct ieee80211_sub_if_data *sdata,
memcpy(pos, ifibss->ssid, ifibss->ssid_len);
pos += ifibss->ssid_len;

- rates = min_t(int, 8, sband->n_bitrates);
+ rate_flags = ieee80211_chandef_rate_flags(&chandef);
+ for (i = 0; i < sband->n_bitrates; i++) {
+ if ((rate_flags & sband->bitrates[i].flags) != rate_flags)
+ continue;
+
+ rates |= BIT(i);
+ rates_n++;
+ }
+
*pos++ = WLAN_EID_SUPP_RATES;
- *pos++ = rates;
- for (i = 0; i < rates; i++) {
- int rate = sband->bitrates[i].bitrate;
+ *pos++ = min_t(int, 8, rates_n);
+ for (ri = 0; ri < sband->n_bitrates; ri++) {
+ int rate = DIV_ROUND_UP(sband->bitrates[ri].bitrate,
+ 5 * (1 << shift));
u8 basic = 0;
- if (basic_rates & BIT(i))
+ if (!(rates & BIT(ri)))
+ continue;
+
+ if (basic_rates & BIT(ri))
basic = 0x80;
- *pos++ = basic | (u8) (rate / 5);
+ *pos++ = basic | (u8) rate;
+ if (++rates_added == 8)
+ break;
}

if (sband->band == IEEE80211_BAND_2GHZ) {
@@ -157,15 +173,20 @@ static void __ieee80211_sta_join_ibss(struct ieee80211_sub_if_data *sdata,
*pos++ = 0;
*pos++ = 0;

- if (sband->n_bitrates > 8) {
+ /* put the remaining rates in WLAN_EID_EXT_SUPP_RATES */
+ if (rates_n > 8) {
*pos++ = WLAN_EID_EXT_SUPP_RATES;
- *pos++ = sband->n_bitrates - 8;
- for (i = 8; i < sband->n_bitrates; i++) {
- int rate = sband->bitrates[i].bitrate;
+ *pos++ = rates_n - 8;
+ for (; ri < sband->n_bitrates; ri++) {
+ int rate = DIV_ROUND_UP(sband->bitrates[ri].bitrate,
+ 5 * (1 << shift));
u8 basic = 0;
- if (basic_rates & BIT(i))
+ if (!(rates & BIT(ri)))
+ continue;
+
+ if (basic_rates & BIT(ri))
basic = 0x80;
- *pos++ = basic | (u8) (rate / 5);
+ *pos++ = basic | (u8) rate;
}
}

@@ -240,7 +261,7 @@ static void __ieee80211_sta_join_ibss(struct ieee80211_sub_if_data *sdata,
sdata->vif.bss_conf.ibss_creator = creator;
ieee80211_bss_info_change_notify(sdata, bss_change);

- ieee80211_sta_def_wmm_params(sdata, sband->n_bitrates, supp_rates);
+ ieee80211_sta_def_wmm_params(sdata, rates, supp_rates);

ifibss->state = IEEE80211_IBSS_MLME_JOINED;
mod_timer(&ifibss->timer,
@@ -264,6 +285,8 @@ static void ieee80211_sta_join_ibss(struct ieee80211_sub_if_data *sdata,
u16 beacon_int = cbss->beacon_interval;
const struct cfg80211_bss_ies *ies;
u64 tsf;
+ u32 rate_flags;
+ int shift;

sdata_assert_lock(sdata);

@@ -271,15 +294,24 @@ static void ieee80211_sta_join_ibss(struct ieee80211_sub_if_data *sdata,
beacon_int = 10;

sband = sdata->local->hw.wiphy->bands[cbss->channel->band];
+ rate_flags = ieee80211_chandef_rate_flags(&sdata->u.ibss.chandef);
+ shift = ieee80211_vif_get_shift(&sdata->vif);

basic_rates = 0;

for (i = 0; i < bss->supp_rates_len; i++) {
- int rate = (bss->supp_rates[i] & 0x7f) * 5;
+ int rate = bss->supp_rates[i] & 0x7f;
bool is_basic = !!(bss->supp_rates[i] & 0x80);

for (j = 0; j < sband->n_bitrates; j++) {
- if (sband->bitrates[j].bitrate == rate) {
+ int brate;
+ if ((rate_flags & sband->bitrates[j].flags)
+ != rate_flags)
+ continue;
+
+ brate = DIV_ROUND_UP(sband->bitrates[j].bitrate,
+ 5 * (1 << shift));
+ if (brate == rate) {
if (is_basic)
basic_rates |= BIT(j);
break;
@@ -488,7 +520,7 @@ static void ieee80211_rx_bss_info(struct ieee80211_sub_if_data *sdata,
sta = sta_info_get(sdata, mgmt->sa);

if (elems->supp_rates) {
- supp_rates = ieee80211_sta_get_rates(local, elems,
+ supp_rates = ieee80211_sta_get_rates(sdata, elems,
band, NULL);
if (sta) {
u32 prev_rates;
@@ -612,7 +644,7 @@ static void ieee80211_rx_bss_info(struct ieee80211_sub_if_data *sdata,
"beacon TSF higher than local TSF - IBSS merge with BSSID %pM\n",
mgmt->bssid);
ieee80211_sta_join_ibss(sdata, bss);
- supp_rates = ieee80211_sta_get_rates(local, elems, band, NULL);
+ supp_rates = ieee80211_sta_get_rates(sdata, elems, band, NULL);
ieee80211_ibss_add_sta(sdata, mgmt->bssid, mgmt->sa,
supp_rates, true);
rcu_read_unlock();
@@ -1047,6 +1079,9 @@ int ieee80211_ibss_join(struct ieee80211_sub_if_data *sdata,
struct cfg80211_ibss_params *params)
{
u32 changed = 0;
+ u32 rate_flags;
+ struct ieee80211_supported_band *sband;
+ int i;

if (params->bssid) {
memcpy(sdata->u.ibss.bssid, params->bssid, ETH_ALEN);
@@ -1057,6 +1092,14 @@ int ieee80211_ibss_join(struct ieee80211_sub_if_data *sdata,
sdata->u.ibss.privacy = params->privacy;
sdata->u.ibss.control_port = params->control_port;
sdata->u.ibss.basic_rates = params->basic_rates;
+
+ /* fix basic_rates if channel does not support these rates */
+ rate_flags = ieee80211_chandef_rate_flags(&params->chandef);
+ sband = sdata->local->hw.wiphy->bands[params->chandef.chan->band];
+ for (i = 0; i < sband->n_bitrates; i++) {
+ if ((rate_flags & sband->bitrates[i].flags) != rate_flags)
+ sdata->u.ibss.basic_rates &= ~BIT(i);
+ }
memcpy(sdata->vif.bss_conf.mcast_rate, params->mcast_rate,
sizeof(params->mcast_rate));

diff --git a/net/mac80211/ieee80211_i.h b/net/mac80211/ieee80211_i.h
index 45b19cc..319ae0b 100644
--- a/net/mac80211/ieee80211_i.h
+++ b/net/mac80211/ieee80211_i.h
@@ -811,7 +811,7 @@ ieee80211_get_sdata_band(struct ieee80211_sub_if_data *sdata)
static inline int
ieee80211_chandef_get_shift(struct cfg80211_chan_def *chandef)
{
- switch (local->hw.conf.chandef.width) {
+ switch (chandef->width) {
case NL80211_CHAN_WIDTH_5:
return 2;
case NL80211_CHAN_WIDTH_10:
@@ -1597,7 +1597,7 @@ void ieee80211_send_deauth_disassoc(struct ieee80211_sub_if_data *sdata,
int ieee80211_build_preq_ies(struct ieee80211_local *local, u8 *buffer,
size_t buffer_len, const u8 *ie, size_t ie_len,
enum ieee80211_band band, u32 rate_mask,
- u8 channel);
+ struct cfg80211_chan_def *chandef);
struct sk_buff *ieee80211_build_probe_req(struct ieee80211_sub_if_data *sdata,
u8 *dst, u32 ratemask,
struct ieee80211_channel *chan,
@@ -1613,7 +1613,7 @@ void ieee80211_send_probe_req(struct ieee80211_sub_if_data *sdata, u8 *dst,
void ieee80211_sta_def_wmm_params(struct ieee80211_sub_if_data *sdata,
const size_t supp_rates_len,
const u8 *supp_rates);
-u32 ieee80211_sta_get_rates(struct ieee80211_local *local,
+u32 ieee80211_sta_get_rates(struct ieee80211_sub_if_data *sdata,
struct ieee802_11_elems *elems,
enum ieee80211_band band, u32 *basic_rates);
int __ieee80211_request_smps(struct ieee80211_sub_if_data *sdata,
@@ -1630,6 +1630,9 @@ u8 *ieee80211_ie_build_ht_oper(u8 *pos, struct ieee80211_sta_ht_cap *ht_cap,
u16 prot_mode);
u8 *ieee80211_ie_build_vht_cap(u8 *pos, struct ieee80211_sta_vht_cap *vht_cap,
u32 cap);
+int ieee80211_parse_bitrates(struct cfg80211_chan_def *chandef,
+ const struct ieee80211_supported_band *sband,
+ const u8 *srates, int srates_len, u32 *rates);
int ieee80211_add_srates_ie(struct ieee80211_sub_if_data *sdata,
struct sk_buff *skb, bool need_basic,
enum ieee80211_band band);
diff --git a/net/mac80211/mesh.c b/net/mac80211/mesh.c
index 5cb0e04..a31a825 100644
--- a/net/mac80211/mesh.c
+++ b/net/mac80211/mesh.c
@@ -85,7 +85,7 @@ bool mesh_matches_local(struct ieee80211_sub_if_data *sdata,
(ifmsh->mesh_auth_id == ie->mesh_config->meshconf_auth)))
return false;

- ieee80211_sta_get_rates(local, ie, ieee80211_get_sdata_band(sdata),
+ ieee80211_sta_get_rates(sdata, ie, ieee80211_get_sdata_band(sdata),
&basic_rates);

if (sdata->vif.bss_conf.basic_rates != basic_rates)
diff --git a/net/mac80211/mesh_plink.c b/net/mac80211/mesh_plink.c
index 02c05fa..6b65d50 100644
--- a/net/mac80211/mesh_plink.c
+++ b/net/mac80211/mesh_plink.c
@@ -379,7 +379,7 @@ static void mesh_sta_info_init(struct ieee80211_sub_if_data *sdata,
u32 rates, basic_rates = 0, changed = 0;

sband = local->hw.wiphy->bands[band];
- rates = ieee80211_sta_get_rates(local, elems, band, &basic_rates);
+ rates = ieee80211_sta_get_rates(sdata, elems, band, &basic_rates);

spin_lock_bh(&sta->lock);
sta->last_rx = jiffies;
diff --git a/net/mac80211/mlme.c b/net/mac80211/mlme.c
index e23263ab..eb45c7e 100644
--- a/net/mac80211/mlme.c
+++ b/net/mac80211/mlme.c
@@ -478,27 +478,6 @@ static int ieee80211_config_bw(struct ieee80211_sub_if_data *sdata,

/* frame sending functions */

-static int ieee80211_compatible_rates(const u8 *supp_rates, int supp_rates_len,
- struct ieee80211_supported_band *sband,
- u32 *rates)
-{
- int i, j, count;
- *rates = 0;
- count = 0;
- for (i = 0; i < supp_rates_len; i++) {
- int rate = (supp_rates[i] & 0x7F) * 5;
-
- for (j = 0; j < sband->n_bitrates; j++)
- if (sband->bitrates[j].bitrate == rate) {
- *rates |= BIT(j);
- count++;
- break;
- }
- }
-
- return count;
-}
-
static void ieee80211_add_ht_ie(struct ieee80211_sub_if_data *sdata,
struct sk_buff *skb, u8 ap_ht_param,
struct ieee80211_supported_band *sband,
@@ -617,12 +596,12 @@ static void ieee80211_send_assoc(struct ieee80211_sub_if_data *sdata)
struct ieee80211_mgmt *mgmt;
u8 *pos, qos_info;
size_t offset = 0, noffset;
- int i, count, rates_len, supp_rates_len;
+ int i, count, rates_len, supp_rates_len, shift;
u16 capab;
struct ieee80211_supported_band *sband;
struct ieee80211_chanctx_conf *chanctx_conf;
struct ieee80211_channel *chan;
- u32 rates = 0;
+ u32 rate_flags, rates = 0;

sdata_assert_lock(sdata);

@@ -633,8 +612,10 @@ static void ieee80211_send_assoc(struct ieee80211_sub_if_data *sdata)
return;
}
chan = chanctx_conf->def.chan;
+ rate_flags = ieee80211_chandef_rate_flags(&chanctx_conf->def);
rcu_read_unlock();
sband = local->hw.wiphy->bands[chan->band];
+ shift = ieee80211_vif_get_shift(&sdata->vif);

if (assoc_data->supp_rates_len) {
/*
@@ -643,17 +624,24 @@ static void ieee80211_send_assoc(struct ieee80211_sub_if_data *sdata)
* in the association request (e.g. D-Link DAP 1353 in
* b-only mode)...
*/
- rates_len = ieee80211_compatible_rates(assoc_data->supp_rates,
- assoc_data->supp_rates_len,
- sband, &rates);
+ rates_len = ieee80211_parse_bitrates(&chanctx_conf->def, sband,
+ assoc_data->supp_rates,
+ assoc_data->supp_rates_len,
+ &rates);
} else {
/*
* In case AP not provide any supported rates information
* before association, we send information element(s) with
* all rates that we support.
*/
- rates = ~0;
- rates_len = sband->n_bitrates;
+ rates_len = 0;
+ for (i = 0; i < sband->n_bitrates; i++) {
+ if ((rate_flags & sband->bitrates[i].flags)
+ != rate_flags)
+ continue;
+ rates |= BIT(i);
+ rates_len++;
+ }
}

skb = alloc_skb(local->hw.extra_tx_headroom +
@@ -730,8 +718,9 @@ static void ieee80211_send_assoc(struct ieee80211_sub_if_data *sdata)
count = 0;
for (i = 0; i < sband->n_bitrates; i++) {
if (BIT(i) & rates) {
- int rate = sband->bitrates[i].bitrate;
- *pos++ = (u8) (rate / 5);
+ int rate = DIV_ROUND_UP(sband->bitrates[i].bitrate,
+ 5 * (1 << shift));
+ *pos++ = (u8) rate;
if (++count == 8)
break;
}
@@ -744,8 +733,10 @@ static void ieee80211_send_assoc(struct ieee80211_sub_if_data *sdata)

for (i++; i < sband->n_bitrates; i++) {
if (BIT(i) & rates) {
- int rate = sband->bitrates[i].bitrate;
- *pos++ = (u8) (rate / 5);
+ int rate;
+ rate = DIV_ROUND_UP(sband->bitrates[i].bitrate,
+ 5 * (1 << shift));
+ *pos++ = (u8) rate;
}
}
}
@@ -2428,15 +2419,16 @@ static void ieee80211_get_rates(struct ieee80211_supported_band *sband,
u8 *supp_rates, unsigned int supp_rates_len,
u32 *rates, u32 *basic_rates,
bool *have_higher_than_11mbit,
- int *min_rate, int *min_rate_index)
+ int *min_rate, int *min_rate_index,
+ int shift, u32 rate_flags)
{
int i, j;

for (i = 0; i < supp_rates_len; i++) {
- int rate = (supp_rates[i] & 0x7f) * 5;
+ int rate = supp_rates[i] & 0x7f;
bool is_basic = !!(supp_rates[i] & 0x80);

- if (rate > 110)
+ if ((rate * 5 * (1 << shift)) > 110)
*have_higher_than_11mbit = true;

/*
@@ -2452,12 +2444,20 @@ static void ieee80211_get_rates(struct ieee80211_supported_band *sband,
continue;

for (j = 0; j < sband->n_bitrates; j++) {
- if (sband->bitrates[j].bitrate == rate) {
+ struct ieee80211_rate *br;
+ int brate;
+
+ br = &sband->bitrates[j];
+ if ((rate_flags & br->flags) != rate_flags)
+ continue;
+
+ brate = DIV_ROUND_UP(br->bitrate, (1 << shift) * 5);
+ if (brate == rate) {
*rates |= BIT(j);
if (is_basic)
*basic_rates |= BIT(j);
- if (rate < *min_rate) {
- *min_rate = rate;
+ if ((rate * 5) < *min_rate) {
+ *min_rate = rate * 5;
*min_rate_index = j;
}
break;
@@ -3882,27 +3882,40 @@ static int ieee80211_prep_connection(struct ieee80211_sub_if_data *sdata,
if (!new_sta)
return -ENOMEM;
}
-
if (new_sta) {
u32 rates = 0, basic_rates = 0;
bool have_higher_than_11mbit;
int min_rate = INT_MAX, min_rate_index = -1;
+ struct ieee80211_chanctx_conf *chanctx_conf;
struct ieee80211_supported_band *sband;
const struct cfg80211_bss_ies *ies;
+ int shift;
+ u32 rate_flags;

sband = local->hw.wiphy->bands[cbss->channel->band];

err = ieee80211_prep_channel(sdata, cbss);
if (err) {
sta_info_free(local, new_sta);
- return err;
+ return -EINVAL;
}
+ shift = ieee80211_vif_get_shift(&sdata->vif);
+
+ rcu_read_lock();
+ chanctx_conf = rcu_dereference(sdata->vif.chanctx_conf);
+ if (WARN_ON(!chanctx_conf)) {
+ rcu_read_unlock();
+ return -EINVAL;
+ }
+ rate_flags = ieee80211_chandef_rate_flags(&chanctx_conf->def);
+ rcu_read_unlock();

ieee80211_get_rates(sband, bss->supp_rates,
bss->supp_rates_len,
&rates, &basic_rates,
&have_higher_than_11mbit,
- &min_rate, &min_rate_index);
+ &min_rate, &min_rate_index,
+ shift, rate_flags);

/*
* This used to be a workaround for basic rates missing
diff --git a/net/mac80211/rate.c b/net/mac80211/rate.c
index 30d58d2..ba63ac8 100644
--- a/net/mac80211/rate.c
+++ b/net/mac80211/rate.c
@@ -232,37 +232,28 @@ static void rc_send_low_broadcast(s8 *idx, u32 basic_rates,
/* could not find a basic rate; use original selection */
}

-static inline s8
-rate_lowest_non_cck_index(struct ieee80211_supported_band *sband,
- struct ieee80211_sta *sta)
-{
- int i;
-
- for (i = 0; i < sband->n_bitrates; i++) {
- struct ieee80211_rate *srate = &sband->bitrates[i];
- if ((srate->bitrate == 10) || (srate->bitrate == 20) ||
- (srate->bitrate == 55) || (srate->bitrate == 110))
- continue;
-
- if (rate_supported(sta, sband->band, i))
- return i;
- }
-
- /* No matching rate found */
- return 0;
-}
-
static void __rate_control_send_low(struct ieee80211_hw *hw,
struct ieee80211_supported_band *sband,
struct ieee80211_sta *sta,
struct ieee80211_tx_info *info)
{
- if ((sband->band != IEEE80211_BAND_2GHZ) ||
- !(info->flags & IEEE80211_TX_CTL_NO_CCK_RATE))
- info->control.rates[0].idx = rate_lowest_index(sband, sta);
- else
- info->control.rates[0].idx =
- rate_lowest_non_cck_index(sband, sta);
+ int i;
+ u32 rate_flags =
+ ieee80211_chandef_rate_flags(&hw->conf.chandef);
+
+ if ((sband->band == IEEE80211_BAND_2GHZ) &&
+ (info->flags & IEEE80211_TX_CTL_NO_CCK_RATE))
+ rate_flags |= IEEE80211_RATE_ERP_G;
+
+ info->control.rates[0].idx = 0;
+ for (i = 0; i < sband->n_bitrates; i++) {
+ if (!rate_supported(sta, sband->band, i))
+ continue;
+
+ info->control.rates[0].idx = i;
+ break;
+ }
+ WARN_ON_ONCE(i == sband->n_bitrates);

info->control.rates[0].count =
(info->flags & IEEE80211_TX_CTL_NO_ACK) ?
@@ -585,6 +576,7 @@ static void rate_control_apply_mask(struct ieee80211_sub_if_data *sdata,
u8 mcs_mask[IEEE80211_HT_MCS_MASK_LEN];
bool has_mcs_mask;
u32 mask;
+ u32 rate_flags;
int i;

/*
@@ -594,6 +586,12 @@ static void rate_control_apply_mask(struct ieee80211_sub_if_data *sdata,
*/
mask = sdata->rc_rateidx_mask[info->band];
has_mcs_mask = sdata->rc_has_mcs_mask[info->band];
+ rate_flags =
+ ieee80211_chandef_rate_flags(&sdata->vif.bss_conf.chandef);
+ for (i = 0; i < sband->n_bitrates; i++)
+ if ((rate_flags & sband->bitrates[i].flags) != rate_flags)
+ mask &= ~BIT(i);
+
if (mask == (1 << sband->n_bitrates) - 1 && !has_mcs_mask)
return;

diff --git a/net/mac80211/rx.c b/net/mac80211/rx.c
index 23dbcfc..90ab888 100644
--- a/net/mac80211/rx.c
+++ b/net/mac80211/rx.c
@@ -207,8 +207,13 @@ ieee80211_add_rx_radiotap_header(struct ieee80211_local *local,
*/
*pos = 0;
} else {
+ int shift = 0;
rthdr->it_present |= cpu_to_le32(1 << IEEE80211_RADIOTAP_RATE);
- *pos = rate->bitrate / 5;
+ if (status->flag & RX_FLAG_10MHZ)
+ shift = 1;
+ else if (status->flag & RX_FLAG_5MHZ)
+ shift = 2;
+ *pos = DIV_ROUND_UP(rate->bitrate, 5 * (1 << shift));
}
pos++;

diff --git a/net/mac80211/scan.c b/net/mac80211/scan.c
index 99b10392..b1bfb05 100644
--- a/net/mac80211/scan.c
+++ b/net/mac80211/scan.c
@@ -195,10 +195,29 @@ void ieee80211_scan_rx(struct ieee80211_local *local, struct sk_buff *skb)
ieee80211_rx_bss_put(local, bss);
}

+static void
+ieee80211_prepare_scan_chandef(struct cfg80211_chan_def *chandef,
+ enum nl80211_bss_scan_width scan_width)
+{
+ memset(chandef, 0, sizeof(*chandef));
+ switch (scan_width) {
+ case NL80211_BSS_CHAN_WIDTH_5:
+ chandef->width = NL80211_CHAN_WIDTH_5;
+ break;
+ case NL80211_BSS_CHAN_WIDTH_10:
+ chandef->width = NL80211_CHAN_WIDTH_10;
+ break;
+ default:
+ chandef->width = NL80211_CHAN_WIDTH_20_NOHT;
+ break;
+ }
+}
+
/* return false if no more work */
static bool ieee80211_prep_hw_scan(struct ieee80211_local *local)
{
struct cfg80211_scan_request *req = local->scan_req;
+ struct cfg80211_chan_def chandef;
enum ieee80211_band band;
int i, ielen, n_chans;

@@ -220,11 +239,12 @@ static bool ieee80211_prep_hw_scan(struct ieee80211_local *local)
} while (!n_chans);

local->hw_scan_req->n_channels = n_chans;
+ ieee80211_prepare_scan_chandef(&chandef, req->scan_width);

ielen = ieee80211_build_preq_ies(local, (u8 *)local->hw_scan_req->ie,
local->hw_scan_ies_bufsize,
req->ie, req->ie_len, band,
- req->rates[band], 0);
+ req->rates[band], &chandef);
local->hw_scan_req->ie_len = ielen;
local->hw_scan_req->no_cck = req->no_cck;

@@ -903,6 +923,7 @@ int ieee80211_request_sched_scan_start(struct ieee80211_sub_if_data *sdata,
{
struct ieee80211_local *local = sdata->local;
struct ieee80211_sched_scan_ies sched_scan_ies = {};
+ struct cfg80211_chan_def chandef;
int ret, i, iebufsz;

iebufsz = 2 + IEEE80211_MAX_SSID_LEN +
@@ -930,10 +951,12 @@ int ieee80211_request_sched_scan_start(struct ieee80211_sub_if_data *sdata,
goto out_free;
}

+ ieee80211_prepare_scan_chandef(&chandef, req->scan_width);
+
sched_scan_ies.len[i] =
ieee80211_build_preq_ies(local, sched_scan_ies.ie[i],
iebufsz, req->ie, req->ie_len,
- i, (u32) -1, 0);
+ i, (u32) -1, &chandef);
}

ret = drv_sched_scan_start(local, sdata, req, &sched_scan_ies);
diff --git a/net/mac80211/status.c b/net/mac80211/status.c
index 4343920..a449664 100644
--- a/net/mac80211/status.c
+++ b/net/mac80211/status.c
@@ -252,9 +252,11 @@ static int ieee80211_tx_radiotap_len(struct ieee80211_tx_info *info)
return len;
}

-static void ieee80211_add_tx_radiotap_header(struct ieee80211_supported_band
- *sband, struct sk_buff *skb,
- int retry_count, int rtap_len)
+static void
+ieee80211_add_tx_radiotap_header(struct ieee80211_sub_if_data *sdata,
+ struct ieee80211_supported_band *sband,
+ struct sk_buff *skb, int retry_count,
+ int rtap_len)
{
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
struct ieee80211_hdr *hdr = (struct ieee80211_hdr *) skb->data;
@@ -280,8 +282,12 @@ static void ieee80211_add_tx_radiotap_header(struct ieee80211_supported_band
/* IEEE80211_RADIOTAP_RATE */
if (info->status.rates[0].idx >= 0 &&
!(info->status.rates[0].flags & IEEE80211_TX_RC_MCS)) {
+ int shift = ieee80211_vif_get_shift(&sdata->vif);
+ int rate;
+
rthdr->it_present |= cpu_to_le32(1 << IEEE80211_RADIOTAP_RATE);
- *pos = sband->bitrates[info->status.rates[0].idx].bitrate / 5;
+ rate = sband->bitrates[info->status.rates[0].idx].bitrate;
+ *pos = DIV_ROUND_UP(rate, 5 * (1 << shift));
/* padding for tx flags */
pos += 2;
}
@@ -624,7 +630,8 @@ void ieee80211_tx_status(struct ieee80211_hw *hw, struct sk_buff *skb)
dev_kfree_skb(skb);
return;
}
- ieee80211_add_tx_radiotap_header(sband, skb, retry_count, rtap_len);
+ ieee80211_add_tx_radiotap_header(sdata, sband, skb, retry_count,
+ rtap_len);

/* XXX: is this sufficient for BPF? */
skb_set_mac_header(skb, 0);
diff --git a/net/mac80211/tx.c b/net/mac80211/tx.c
index 3523daa..f82301b 100644
--- a/net/mac80211/tx.c
+++ b/net/mac80211/tx.c
@@ -40,12 +40,22 @@ static __le16 ieee80211_duration(struct ieee80211_tx_data *tx,
struct sk_buff *skb, int group_addr,
int next_frag_len)
{
- int rate, mrate, erp, dur, i, shift;
+ int rate, mrate, erp, dur, i, shift = 0;
struct ieee80211_rate *txrate;
struct ieee80211_local *local = tx->local;
struct ieee80211_supported_band *sband;
struct ieee80211_hdr *hdr;
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb);
+ struct ieee80211_chanctx_conf *chanctx_conf;
+ u32 rate_flags = 0;
+
+ rcu_read_lock();
+ chanctx_conf = rcu_dereference(tx->sdata->vif.chanctx_conf);
+ if (chanctx_conf) {
+ shift = ieee80211_chandef_get_shift(&chanctx_conf->def);
+ rate_flags = ieee80211_chandef_rate_flags(&chanctx_conf->def);
+ }
+ rcu_read_unlock();

/* assume HW handles this */
if (tx->rate.flags & IEEE80211_TX_RC_MCS)
@@ -122,8 +132,11 @@ static __le16 ieee80211_duration(struct ieee80211_tx_data *tx,
if (r->bitrate > txrate->bitrate)
break;

+ if ((rate_flags & r->flags) != rate_flags)
+ continue;
+
if (tx->sdata->vif.bss_conf.basic_rates & BIT(i))
- rate = r->bitrate;
+ rate = DIV_ROUND_UP(r->bitrate, 1 << shift);

switch (sband->band) {
case IEEE80211_BAND_2GHZ: {
@@ -150,11 +163,9 @@ static __le16 ieee80211_duration(struct ieee80211_tx_data *tx,
if (rate == -1) {
/* No matching basic rate found; use highest suitable mandatory
* PHY rate */
- rate = mrate;
+ rate = DIV_ROUND_UP(mrate, 1 << shift);
}

- shift = ieee80211_vif_get_shift(&tx->sdata->vif);
-
/* Don't calculate ACKs for QoS Frames with NoAck Policy set */
if (ieee80211_is_data_qos(hdr->frame_control) &&
*(ieee80211_get_qos_ctl(hdr)) & IEEE80211_QOS_CTL_ACK_POLICY_NOACK)
diff --git a/net/mac80211/util.c b/net/mac80211/util.c
index 61856e1..1e45891c 100644
--- a/net/mac80211/util.c
+++ b/net/mac80211/util.c
@@ -141,14 +141,18 @@ int ieee80211_frame_duration(enum ieee80211_band band, size_t len,
dur = 16; /* SIFS + signal ext */
dur += 16; /* IEEE 802.11-2012 18.3.2.4: T_PREAMBLE = 16 usec */
dur += 4; /* IEEE 802.11-2012 18.3.2.4: T_SIGNAL = 4 usec */
- dur += 4 * DIV_ROUND_UP((16 + 8 * (len + 4) + 6) * 10,
- 4 * rate); /* T_SYM x N_SYM */

/* IEEE 802.11-2012 18.3.2.4: all values above are:
* * times 4 for 5 MHz
* * times 2 for 10 MHz
*/
dur *= 1 << shift;
+
+ /* rates should already consider the channel bandwidth,
+ * don't apply divisor again.
+ */
+ dur += 4 * DIV_ROUND_UP((16 + 8 * (len + 4) + 6) * 10,
+ 4 * rate); /* T_SYM x N_SYM */
} else {
/*
* 802.11b or 802.11g with 802.11b compatibility:
@@ -205,7 +209,7 @@ __le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
struct ieee80211_rate *rate;
struct ieee80211_sub_if_data *sdata;
bool short_preamble;
- int erp, shift = 0;
+ int erp, shift = 0, bitrate;
u16 dur;
struct ieee80211_supported_band *sband;

@@ -224,14 +228,16 @@ __le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
shift = ieee80211_vif_get_shift(vif);
}

+ bitrate = DIV_ROUND_UP(rate->bitrate, 1 << shift);
+
/* CTS duration */
- dur = ieee80211_frame_duration(sband->band, 10, rate->bitrate,
+ dur = ieee80211_frame_duration(sband->band, 10, bitrate,
erp, short_preamble, shift);
/* Data frame duration */
- dur += ieee80211_frame_duration(sband->band, frame_len, rate->bitrate,
+ dur += ieee80211_frame_duration(sband->band, frame_len, bitrate,
erp, short_preamble, shift);
/* ACK duration */
- dur += ieee80211_frame_duration(sband->band, 10, rate->bitrate,
+ dur += ieee80211_frame_duration(sband->band, 10, bitrate,
erp, short_preamble, shift);

return cpu_to_le16(dur);
@@ -247,7 +253,7 @@ __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
struct ieee80211_rate *rate;
struct ieee80211_sub_if_data *sdata;
bool short_preamble;
- int erp, shift = 0;
+ int erp, shift = 0, bitrate;
u16 dur;
struct ieee80211_supported_band *sband;

@@ -265,12 +271,14 @@ __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
shift = ieee80211_vif_get_shift(vif);
}

+ bitrate = DIV_ROUND_UP(rate->bitrate, 1 << shift);
+
/* Data frame duration */
- dur = ieee80211_frame_duration(sband->band, frame_len, rate->bitrate,
+ dur = ieee80211_frame_duration(sband->band, frame_len, bitrate,
erp, short_preamble, shift);
if (!(frame_txctl->flags & IEEE80211_TX_CTL_NO_ACK)) {
/* ACK duration */
- dur += ieee80211_frame_duration(sband->band, 10, rate->bitrate,
+ dur += ieee80211_frame_duration(sband->band, 10, bitrate,
erp, short_preamble, shift);
}

@@ -1175,7 +1183,7 @@ void ieee80211_send_deauth_disassoc(struct ieee80211_sub_if_data *sdata,
int ieee80211_build_preq_ies(struct ieee80211_local *local, u8 *buffer,
size_t buffer_len, const u8 *ie, size_t ie_len,
enum ieee80211_band band, u32 rate_mask,
- u8 channel)
+ struct cfg80211_chan_def *chandef)
{
struct ieee80211_supported_band *sband;
u8 *pos = buffer, *end = buffer + buffer_len;
@@ -1184,16 +1192,26 @@ int ieee80211_build_preq_ies(struct ieee80211_local *local, u8 *buffer,
u8 rates[32];
int num_rates;
int ext_rates_len;
+ int shift;
+ u32 rate_flags;

sband = local->hw.wiphy->bands[band];
if (WARN_ON_ONCE(!sband))
return 0;

+ rate_flags = ieee80211_chandef_rate_flags(chandef);
+ shift = ieee80211_chandef_get_shift(chandef);
+
num_rates = 0;
for (i = 0; i < sband->n_bitrates; i++) {
if ((BIT(i) & rate_mask) == 0)
continue; /* skip rate */
- rates[num_rates++] = (u8) (sband->bitrates[i].bitrate / 5);
+ if ((rate_flags & sband->bitrates[i].flags) != rate_flags)
+ continue;
+
+ rates[num_rates++] =
+ (u8) DIV_ROUND_UP(sband->bitrates[i].bitrate,
+ (1 << shift) * 5);
}

supp_rates_len = min_t(int, num_rates, 8);
@@ -1233,12 +1251,13 @@ int ieee80211_build_preq_ies(struct ieee80211_local *local, u8 *buffer,
pos += ext_rates_len;
}

- if (channel && sband->band == IEEE80211_BAND_2GHZ) {
+ if (chandef->chan && sband->band == IEEE80211_BAND_2GHZ) {
if (end - pos < 3)
goto out_err;
*pos++ = WLAN_EID_DS_PARAMS;
*pos++ = 1;
- *pos++ = channel;
+ *pos++ = ieee80211_frequency_to_channel(
+ chandef->chan->center_freq);
}

/* insert custom IEs that go before HT */
@@ -1303,9 +1322,9 @@ struct sk_buff *ieee80211_build_probe_req(struct ieee80211_sub_if_data *sdata,
bool directed)
{
struct ieee80211_local *local = sdata->local;
+ struct cfg80211_chan_def chandef;
struct sk_buff *skb;
struct ieee80211_mgmt *mgmt;
- u8 chan_no;
int ies_len;

/*
@@ -1313,10 +1332,11 @@ struct sk_buff *ieee80211_build_probe_req(struct ieee80211_sub_if_data *sdata,
* in order to maximize the chance that we get a response. Some
* badly-behaved APs don't respond when this parameter is included.
*/
+ chandef.width = sdata->vif.bss_conf.chandef.width;
if (directed)
- chan_no = 0;
+ chandef.chan = NULL;
else
- chan_no = ieee80211_frequency_to_channel(chan->center_freq);
+ chandef.chan = chan;

skb = ieee80211_probereq_get(&local->hw, &sdata->vif,
ssid, ssid_len, 100 + ie_len);
@@ -1326,7 +1346,7 @@ struct sk_buff *ieee80211_build_probe_req(struct ieee80211_sub_if_data *sdata,
ies_len = ieee80211_build_preq_ies(local, skb_tail_pointer(skb),
skb_tailroom(skb),
ie, ie_len, chan->band,
- ratemask, chan_no);
+ ratemask, &chandef);
skb_put(skb, ies_len);

if (dst) {
@@ -1360,16 +1380,19 @@ void ieee80211_send_probe_req(struct ieee80211_sub_if_data *sdata, u8 *dst,
}
}

-u32 ieee80211_sta_get_rates(struct ieee80211_local *local,
+u32 ieee80211_sta_get_rates(struct ieee80211_sub_if_data *sdata,
struct ieee802_11_elems *elems,
enum ieee80211_band band, u32 *basic_rates)
{
struct ieee80211_supported_band *sband;
struct ieee80211_rate *bitrates;
size_t num_rates;
- u32 supp_rates;
- int i, j;
- sband = local->hw.wiphy->bands[band];
+ u32 supp_rates, rate_flags;
+ int i, j, shift;
+ sband = sdata->local->hw.wiphy->bands[band];
+
+ rate_flags = ieee80211_chandef_rate_flags(&sdata->vif.bss_conf.chandef);
+ shift = ieee80211_vif_get_shift(&sdata->vif);

if (WARN_ON(!sband))
return 1;
@@ -1394,7 +1417,15 @@ u32 ieee80211_sta_get_rates(struct ieee80211_local *local,
continue;

for (j = 0; j < num_rates; j++) {
- if (bitrates[j].bitrate == own_rate) {
+ int brate;
+ if ((rate_flags & sband->bitrates[j].flags)
+ != rate_flags)
+ continue;
+
+ brate = DIV_ROUND_UP(sband->bitrates[j].bitrate,
+ 1 << shift);
+
+ if (brate == own_rate) {
supp_rates |= BIT(j);
if (basic_rates && is_basic)
*basic_rates |= BIT(j);
@@ -2017,18 +2048,56 @@ void ieee80211_ht_oper_to_chandef(struct ieee80211_channel *control_chan,
cfg80211_chandef_create(chandef, control_chan, channel_type);
}

+int ieee80211_parse_bitrates(struct cfg80211_chan_def *chandef,
+ const struct ieee80211_supported_band *sband,
+ const u8 *srates, int srates_len, u32 *rates)
+{
+ u32 rate_flags = ieee80211_chandef_rate_flags(chandef);
+ int shift = ieee80211_chandef_get_shift(chandef);
+ struct ieee80211_rate *br;
+ int brate, rate, i, j, count = 0;
+
+ *rates = 0;
+
+ for (i = 0; i < srates_len; i++) {
+ rate = srates[i] & 0x7f;
+
+ for (j = 0; j < sband->n_bitrates; j++) {
+ br = &sband->bitrates[j];
+ if ((rate_flags & br->flags) != rate_flags)
+ continue;
+
+ brate = DIV_ROUND_UP(br->bitrate, (1 << shift) * 5);
+ if (brate == rate) {
+ *rates |= BIT(j);
+ count++;
+ break;
+ }
+ }
+ }
+ return count;
+}
+
int ieee80211_add_srates_ie(struct ieee80211_sub_if_data *sdata,
struct sk_buff *skb, bool need_basic,
enum ieee80211_band band)
{
struct ieee80211_local *local = sdata->local;
struct ieee80211_supported_band *sband;
- int rate;
+ int rate, shift;
u8 i, rates, *pos;
u32 basic_rates = sdata->vif.bss_conf.basic_rates;
+ u32 rate_flags;

+ shift = ieee80211_vif_get_shift(&sdata->vif);
+ rate_flags = ieee80211_chandef_rate_flags(&sdata->vif.bss_conf.chandef);
sband = local->hw.wiphy->bands[band];
- rates = sband->n_bitrates;
+ rates = 0;
+ for (i = 0; i < sband->n_bitrates; i++) {
+ if ((rate_flags & sband->bitrates[i].flags) != rate_flags)
+ continue;
+ rates++;
+ }
if (rates > 8)
rates = 8;

@@ -2040,10 +2109,15 @@ int ieee80211_add_srates_ie(struct ieee80211_sub_if_data *sdata,
*pos++ = rates;
for (i = 0; i < rates; i++) {
u8 basic = 0;
+ if ((rate_flags & sband->bitrates[i].flags) != rate_flags)
+ continue;
+
if (need_basic && basic_rates & BIT(i))
basic = 0x80;
rate = sband->bitrates[i].bitrate;
- *pos++ = basic | (u8) (rate / 5);
+ rate = DIV_ROUND_UP(sband->bitrates[i].bitrate,
+ 5 * (1 << shift));
+ *pos++ = basic | (u8) rate;
}

return 0;
@@ -2055,12 +2129,22 @@ int ieee80211_add_ext_srates_ie(struct ieee80211_sub_if_data *sdata,
{
struct ieee80211_local *local = sdata->local;
struct ieee80211_supported_band *sband;
- int rate;
+ int rate, skip, shift;
u8 i, exrates, *pos;
u32 basic_rates = sdata->vif.bss_conf.basic_rates;
+ u32 rate_flags;
+
+ rate_flags = ieee80211_chandef_rate_flags(&sdata->vif.bss_conf.chandef);
+ shift = ieee80211_vif_get_shift(&sdata->vif);

sband = local->hw.wiphy->bands[band];
- exrates = sband->n_bitrates;
+ exrates = 0;
+ for (i = 0; i < sband->n_bitrates; i++) {
+ if ((rate_flags & sband->bitrates[i].flags) != rate_flags)
+ continue;
+ exrates++;
+ }
+
if (exrates > 8)
exrates -= 8;
else
@@ -2073,12 +2157,19 @@ int ieee80211_add_ext_srates_ie(struct ieee80211_sub_if_data *sdata,
pos = skb_put(skb, exrates + 2);
*pos++ = WLAN_EID_EXT_SUPP_RATES;
*pos++ = exrates;
+ skip = 0;
for (i = 8; i < sband->n_bitrates; i++) {
u8 basic = 0;
+ if ((rate_flags & sband->bitrates[i].flags)
+ != rate_flags)
+ continue;
+ if (skip++ < 8)
+ continue;
if (need_basic && basic_rates & BIT(i))
basic = 0x80;
- rate = sband->bitrates[i].bitrate;
- *pos++ = basic | (u8) (rate / 5);
+ rate = DIV_ROUND_UP(sband->bitrates[i].bitrate,
+ 5 * (1 << shift));
+ *pos++ = basic | (u8) rate;
}
}
return 0;
@@ -2162,9 +2253,17 @@ u64 ieee80211_calculate_rx_timestamp(struct ieee80211_local *local,
ri.flags |= RATE_INFO_FLAGS_SHORT_GI;
} else {
struct ieee80211_supported_band *sband;
+ int shift = 0;
+ int bitrate;
+
+ if (status->flag & RX_FLAG_10MHZ)
+ shift = 1;
+ if (status->flag & RX_FLAG_5MHZ)
+ shift = 2;

sband = local->hw.wiphy->bands[status->band];
- ri.legacy = sband->bitrates[status->rate_idx].bitrate;
+ bitrate = sband->bitrates[status->rate_idx].bitrate;
+ ri.legacy = DIV_ROUND_UP(bitrate, (1 << shift));
}

rate = cfg80211_calculate_bitrate(&ri);
--
1.7.10.4


2013-06-27 16:59:18

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 10/18] nl80211: allow 5 and 10 MHz channels for IBSS

Whether the wiphy supports it or not is already checked, so what is left
is to enable these channel types.

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
net/wireless/nl80211.c | 2 ++
1 file changed, 2 insertions(+)

diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c
index ebd889d..10755dc 100644
--- a/net/wireless/nl80211.c
+++ b/net/wireless/nl80211.c
@@ -6300,6 +6300,8 @@ static int nl80211_join_ibss(struct sk_buff *skb, struct genl_info *info)
return -EINVAL;

switch (ibss.chandef.width) {
+ case NL80211_CHAN_WIDTH_5:
+ case NL80211_CHAN_WIDTH_10:
case NL80211_CHAN_WIDTH_20_NOHT:
break;
case NL80211_CHAN_WIDTH_20:
--
1.7.10.4


2013-06-27 16:59:16

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 13/18] ath9k: report 5/10 MHz channels

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
drivers/net/wireless/ath/ath9k/recv.c | 11 +++++++++++
1 file changed, 11 insertions(+)

diff --git a/drivers/net/wireless/ath/ath9k/recv.c b/drivers/net/wireless/ath/ath9k/recv.c
index 865e043..0b0bc9d 100644
--- a/drivers/net/wireless/ath/ath9k/recv.c
+++ b/drivers/net/wireless/ath/ath9k/recv.c
@@ -865,6 +865,17 @@ static int ath9k_process_rate(struct ath_common *common,
band = hw->conf.chandef.chan->band;
sband = hw->wiphy->bands[band];

+ switch (hw->conf.chandef.width) {
+ case NL80211_CHAN_WIDTH_5:
+ rxs->flag |= RX_FLAG_5MHZ;
+ break;
+ case NL80211_CHAN_WIDTH_10:
+ rxs->flag |= RX_FLAG_10MHZ;
+ break;
+ default:
+ break;
+ }
+
if (rx_stats->rs_rate & 0x80) {
/* HT rate */
rxs->flag |= RX_FLAG_HT;
--
1.7.10.4


2013-06-27 16:59:17

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 05/18] cfg80211/mac80211: get mandatory rates based on rate flags

Mandatory rates for 5 and 10 MHz are different from the rates used for
20 MHz in 2.4 GHz mode, as they use OFDM only.

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>

---
Changes to PATCHv4:
* it is now based on scan_width instead of rate flags
---
include/net/cfg80211.h | 4 +++-
net/mac80211/ibss.c | 19 +++++++++++++++----
net/wireless/mesh.c | 5 ++++-
net/wireless/util.c | 14 ++++++++++----
4 files changed, 32 insertions(+), 10 deletions(-)

diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 820cce5..83d52dc 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -3069,11 +3069,13 @@ ieee80211_get_response_rate(struct ieee80211_supported_band *sband,
/**
* ieee80211_mandatory_rates - get mandatory rates for a given band
* @sband: the band to look for rates in
+ * @scan_width: width of the control channel
*
* This function returns a bitmap of the mandatory rates for the given
* band, bits are set according to the rate position in the bitrates array.
*/
-u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband);
+u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband,
+ enum nl80211_bss_scan_width scan_width);

/*
* Radiotap parsing functions -- for controlled injection support
diff --git a/net/mac80211/ibss.c b/net/mac80211/ibss.c
index fa91df8..d0c27dc 100644
--- a/net/mac80211/ibss.c
+++ b/net/mac80211/ibss.c
@@ -376,6 +376,7 @@ ieee80211_ibss_add_sta(struct ieee80211_sub_if_data *sdata,
struct sta_info *sta;
struct ieee80211_chanctx_conf *chanctx_conf;
struct ieee80211_supported_band *sband;
+ enum nl80211_bss_scan_width scan_width;
int band;

/*
@@ -404,6 +405,7 @@ ieee80211_ibss_add_sta(struct ieee80211_sub_if_data *sdata,
if (WARN_ON_ONCE(!chanctx_conf))
return NULL;
band = chanctx_conf->def.chan->band;
+ scan_width = cfg80211_chandef_to_scan_width(&chanctx_conf->def);
rcu_read_unlock();

sta = sta_info_alloc(sdata, addr, GFP_KERNEL);
@@ -417,7 +419,7 @@ ieee80211_ibss_add_sta(struct ieee80211_sub_if_data *sdata,
/* make sure mandatory rates are always added */
sband = local->hw.wiphy->bands[band];
sta->sta.supp_rates[band] = supp_rates |
- ieee80211_mandatory_rates(sband);
+ ieee80211_mandatory_rates(sband, scan_width);

return ieee80211_ibss_finish_sta(sta, auth);
}
@@ -499,6 +501,7 @@ static void ieee80211_rx_bss_info(struct ieee80211_sub_if_data *sdata,
u64 beacon_timestamp, rx_timestamp;
u32 supp_rates = 0;
enum ieee80211_band band = rx_status->band;
+ enum nl80211_bss_scan_width scan_width;
struct ieee80211_supported_band *sband = local->hw.wiphy->bands[band];
bool rates_updated = false;

@@ -527,9 +530,15 @@ static void ieee80211_rx_bss_info(struct ieee80211_sub_if_data *sdata,

prev_rates = sta->sta.supp_rates[band];
/* make sure mandatory rates are always added */
+ scan_width = NL80211_BSS_CHAN_WIDTH_20;
+ if (rx_status->flag & RX_FLAG_5MHZ)
+ scan_width = NL80211_BSS_CHAN_WIDTH_5;
+ if (rx_status->flag & RX_FLAG_10MHZ)
+ scan_width = NL80211_BSS_CHAN_WIDTH_10;
+
sta->sta.supp_rates[band] = supp_rates |
- ieee80211_mandatory_rates(sband);
-
+ ieee80211_mandatory_rates(sband,
+ scan_width);
if (sta->sta.supp_rates[band] != prev_rates) {
ibss_dbg(sdata,
"updated supp_rates set for %pM based on beacon/probe_resp (0x%x -> 0x%x)\n",
@@ -663,6 +672,7 @@ void ieee80211_ibss_rx_no_sta(struct ieee80211_sub_if_data *sdata,
struct sta_info *sta;
struct ieee80211_chanctx_conf *chanctx_conf;
struct ieee80211_supported_band *sband;
+ enum nl80211_bss_scan_width scan_width;
int band;

/*
@@ -688,6 +698,7 @@ void ieee80211_ibss_rx_no_sta(struct ieee80211_sub_if_data *sdata,
return;
}
band = chanctx_conf->def.chan->band;
+ scan_width = cfg80211_chandef_to_scan_width(&chanctx_conf->def);
rcu_read_unlock();

sta = sta_info_alloc(sdata, addr, GFP_ATOMIC);
@@ -699,7 +710,7 @@ void ieee80211_ibss_rx_no_sta(struct ieee80211_sub_if_data *sdata,
/* make sure mandatory rates are always added */
sband = local->hw.wiphy->bands[band];
sta->sta.supp_rates[band] = supp_rates |
- ieee80211_mandatory_rates(sband);
+ ieee80211_mandatory_rates(sband, scan_width);

spin_lock(&ifibss->incomplete_lock);
list_add(&sta->list, &ifibss->incomplete_stations);
diff --git a/net/wireless/mesh.c b/net/wireless/mesh.c
index 30c4920..0553fd4 100644
--- a/net/wireless/mesh.c
+++ b/net/wireless/mesh.c
@@ -167,9 +167,12 @@ int __cfg80211_join_mesh(struct cfg80211_registered_device *rdev,
* basic rates
*/
if (!setup->basic_rates) {
+ enum nl80211_bss_scan_width scan_width;
struct ieee80211_supported_band *sband =
rdev->wiphy.bands[setup->chandef.chan->band];
- setup->basic_rates = ieee80211_mandatory_rates(sband);
+ scan_width = cfg80211_chandef_to_scan_width(&setup->chandef);
+ setup->basic_rates = ieee80211_mandatory_rates(sband,
+ scan_width);
}

if (!cfg80211_reg_can_beacon(&rdev->wiphy, &setup->chandef))
diff --git a/net/wireless/util.c b/net/wireless/util.c
index 74458b7..ce090c1 100644
--- a/net/wireless/util.c
+++ b/net/wireless/util.c
@@ -33,7 +33,8 @@ ieee80211_get_response_rate(struct ieee80211_supported_band *sband,
}
EXPORT_SYMBOL(ieee80211_get_response_rate);

-u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband)
+u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband,
+ enum nl80211_bss_scan_width scan_width)
{
struct ieee80211_rate *bitrates;
u32 mandatory_rates = 0;
@@ -43,10 +44,15 @@ u32 ieee80211_mandatory_rates(struct ieee80211_supported_band *sband)
if (WARN_ON(!sband))
return 1;

- if (sband->band == IEEE80211_BAND_2GHZ)
- mandatory_flag = IEEE80211_RATE_MANDATORY_B;
- else
+ if (sband->band == IEEE80211_BAND_2GHZ) {
+ if (scan_width == NL80211_BSS_CHAN_WIDTH_5 ||
+ scan_width == NL80211_BSS_CHAN_WIDTH_10)
+ mandatory_flag = IEEE80211_RATE_MANDATORY_G;
+ else
+ mandatory_flag = IEEE80211_RATE_MANDATORY_B;
+ } else {
mandatory_flag = IEEE80211_RATE_MANDATORY_A;
+ }

bitrates = sband->bitrates;
for (i = 0; i < sband->n_bitrates; i++)
--
1.7.10.4


2013-06-27 16:59:12

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 02/18] mac80211/rc80211: add chandef to rate initialization

5 and 10 MHz support needs to know the current operating channel width,
add the chandef to the rate control API.

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
drivers/net/wireless/ath/ath9k/rc.c | 2 ++
drivers/net/wireless/iwlegacy/3945-rs.c | 1 +
drivers/net/wireless/iwlegacy/4965-rs.c | 1 +
drivers/net/wireless/iwlwifi/dvm/rs.c | 3 ++-
drivers/net/wireless/iwlwifi/mvm/rs.c | 5 +++--
drivers/net/wireless/rtlwifi/rc.c | 1 +
include/net/mac80211.h | 2 ++
net/mac80211/rate.h | 22 +++++++++++++++++-----
net/mac80211/rc80211_minstrel.c | 3 ++-
net/mac80211/rc80211_minstrel_ht.c | 10 +++++++---
net/mac80211/rc80211_pid_algo.c | 1 +
11 files changed, 39 insertions(+), 12 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/rc.c b/drivers/net/wireless/ath/ath9k/rc.c
index 7eb1f4b..a3c4ca0 100644
--- a/drivers/net/wireless/ath/ath9k/rc.c
+++ b/drivers/net/wireless/ath/ath9k/rc.c
@@ -1275,6 +1275,7 @@ static void ath_tx_status(void *priv, struct ieee80211_supported_band *sband,
}

static void ath_rate_init(void *priv, struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
struct ieee80211_sta *sta, void *priv_sta)
{
struct ath_softc *sc = priv;
@@ -1313,6 +1314,7 @@ static void ath_rate_init(void *priv, struct ieee80211_supported_band *sband,
}

static void ath_rate_update(void *priv, struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
struct ieee80211_sta *sta, void *priv_sta,
u32 changed)
{
diff --git a/drivers/net/wireless/iwlegacy/3945-rs.c b/drivers/net/wireless/iwlegacy/3945-rs.c
index fe31590..aea667b 100644
--- a/drivers/net/wireless/iwlegacy/3945-rs.c
+++ b/drivers/net/wireless/iwlegacy/3945-rs.c
@@ -887,6 +887,7 @@ il3945_remove_debugfs(void *il, void *il_sta)
*/
static void
il3945_rs_rate_init_stub(void *il_r, struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
struct ieee80211_sta *sta, void *il_sta)
{
}
diff --git a/drivers/net/wireless/iwlegacy/4965-rs.c b/drivers/net/wireless/iwlegacy/4965-rs.c
index ed3c42a..3ccbaf7 100644
--- a/drivers/net/wireless/iwlegacy/4965-rs.c
+++ b/drivers/net/wireless/iwlegacy/4965-rs.c
@@ -2803,6 +2803,7 @@ il4965_rs_remove_debugfs(void *il, void *il_sta)
*/
static void
il4965_rs_rate_init_stub(void *il_r, struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
struct ieee80211_sta *sta, void *il_sta)
{
}
diff --git a/drivers/net/wireless/iwlwifi/dvm/rs.c b/drivers/net/wireless/iwlwifi/dvm/rs.c
index 8fe76dc..3bf8ae0 100644
--- a/drivers/net/wireless/iwlwifi/dvm/rs.c
+++ b/drivers/net/wireless/iwlwifi/dvm/rs.c
@@ -3338,7 +3338,8 @@ static void rs_remove_debugfs(void *priv, void *priv_sta)
* station is added we ignore it.
*/
static void rs_rate_init_stub(void *priv_r, struct ieee80211_supported_band *sband,
- struct ieee80211_sta *sta, void *priv_sta)
+ struct cfg80211_chan_def *chandef,
+ struct ieee80211_sta *sta, void *priv_sta)
{
}
static struct rate_control_ops rs_ops = {
diff --git a/drivers/net/wireless/iwlwifi/mvm/rs.c b/drivers/net/wireless/iwlwifi/mvm/rs.c
index 31587a3..af27967 100644
--- a/drivers/net/wireless/iwlwifi/mvm/rs.c
+++ b/drivers/net/wireless/iwlwifi/mvm/rs.c
@@ -3165,8 +3165,9 @@ static void rs_remove_debugfs(void *mvm, void *mvm_sta)
* station is added we ignore it.
*/
static void rs_rate_init_stub(void *mvm_r,
- struct ieee80211_supported_band *sband,
- struct ieee80211_sta *sta, void *mvm_sta)
+ struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
+ struct ieee80211_sta *sta, void *mvm_sta)
{
}
static struct rate_control_ops rs_mvm_ops = {
diff --git a/drivers/net/wireless/rtlwifi/rc.c b/drivers/net/wireless/rtlwifi/rc.c
index f9f059d..a98acef 100644
--- a/drivers/net/wireless/rtlwifi/rc.c
+++ b/drivers/net/wireless/rtlwifi/rc.c
@@ -218,6 +218,7 @@ static void rtl_tx_status(void *ppriv,

static void rtl_rate_init(void *ppriv,
struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
struct ieee80211_sta *sta, void *priv_sta)
{
}
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index a405a7a..9445f38 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -4202,8 +4202,10 @@ struct rate_control_ops {

void *(*alloc_sta)(void *priv, struct ieee80211_sta *sta, gfp_t gfp);
void (*rate_init)(void *priv, struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
struct ieee80211_sta *sta, void *priv_sta);
void (*rate_update)(void *priv, struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
struct ieee80211_sta *sta, void *priv_sta,
u32 changed);
void (*free_sta)(void *priv, struct ieee80211_sta *sta,
diff --git a/net/mac80211/rate.h b/net/mac80211/rate.h
index d35a5dd..5dedc56 100644
--- a/net/mac80211/rate.h
+++ b/net/mac80211/rate.h
@@ -66,11 +66,12 @@ static inline void rate_control_rate_init(struct sta_info *sta)
}

sband = local->hw.wiphy->bands[chanctx_conf->def.chan->band];
- rcu_read_unlock();

ieee80211_sta_set_rx_nss(sta);

- ref->ops->rate_init(ref->priv, sband, ista, priv_sta);
+ ref->ops->rate_init(ref->priv, sband, &chanctx_conf->def, ista,
+ priv_sta);
+ rcu_read_unlock();
set_sta_flag(sta, WLAN_STA_RATE_CONTROL);
}

@@ -81,10 +82,21 @@ static inline void rate_control_rate_update(struct ieee80211_local *local,
struct rate_control_ref *ref = local->rate_ctrl;
struct ieee80211_sta *ista = &sta->sta;
void *priv_sta = sta->rate_ctrl_priv;
+ struct ieee80211_chanctx_conf *chanctx_conf;

- if (ref && ref->ops->rate_update)
- ref->ops->rate_update(ref->priv, sband, ista,
- priv_sta, changed);
+ if (ref && ref->ops->rate_update) {
+ rcu_read_lock();
+
+ chanctx_conf = rcu_dereference(sta->sdata->vif.chanctx_conf);
+ if (WARN_ON(!chanctx_conf)) {
+ rcu_read_unlock();
+ return;
+ }
+
+ ref->ops->rate_update(ref->priv, sband, &chanctx_conf->def,
+ ista, priv_sta, changed);
+ rcu_read_unlock();
+ }
drv_sta_rc_update(local, sta->sdata, &sta->sta, changed);
}

diff --git a/net/mac80211/rc80211_minstrel.c b/net/mac80211/rc80211_minstrel.c
index ac7ef54..5b25966 100644
--- a/net/mac80211/rc80211_minstrel.c
+++ b/net/mac80211/rc80211_minstrel.c
@@ -417,7 +417,8 @@ init_sample_table(struct minstrel_sta_info *mi)

static void
minstrel_rate_init(void *priv, struct ieee80211_supported_band *sband,
- struct ieee80211_sta *sta, void *priv_sta)
+ struct cfg80211_chan_def *chandef,
+ struct ieee80211_sta *sta, void *priv_sta)
{
struct minstrel_sta_info *mi = priv_sta;
struct minstrel_priv *mp = priv;
diff --git a/net/mac80211/rc80211_minstrel_ht.c b/net/mac80211/rc80211_minstrel_ht.c
index 5b2d301..5256297 100644
--- a/net/mac80211/rc80211_minstrel_ht.c
+++ b/net/mac80211/rc80211_minstrel_ht.c
@@ -836,6 +836,7 @@ minstrel_ht_update_cck(struct minstrel_priv *mp, struct minstrel_ht_sta *mi,

static void
minstrel_ht_update_caps(void *priv, struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
struct ieee80211_sta *sta, void *priv_sta)
{
struct minstrel_priv *mp = priv;
@@ -931,22 +932,25 @@ use_legacy:
memset(&msp->legacy, 0, sizeof(msp->legacy));
msp->legacy.r = msp->ratelist;
msp->legacy.sample_table = msp->sample_table;
- return mac80211_minstrel.rate_init(priv, sband, sta, &msp->legacy);
+ return mac80211_minstrel.rate_init(priv, sband, chandef, sta,
+ &msp->legacy);
}

static void
minstrel_ht_rate_init(void *priv, struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
struct ieee80211_sta *sta, void *priv_sta)
{
- minstrel_ht_update_caps(priv, sband, sta, priv_sta);
+ minstrel_ht_update_caps(priv, sband, chandef, sta, priv_sta);
}

static void
minstrel_ht_rate_update(void *priv, struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
struct ieee80211_sta *sta, void *priv_sta,
u32 changed)
{
- minstrel_ht_update_caps(priv, sband, sta, priv_sta);
+ minstrel_ht_update_caps(priv, sband, chandef, sta, priv_sta);
}

static void *
diff --git a/net/mac80211/rc80211_pid_algo.c b/net/mac80211/rc80211_pid_algo.c
index 502d3ec..958fad0 100644
--- a/net/mac80211/rc80211_pid_algo.c
+++ b/net/mac80211/rc80211_pid_algo.c
@@ -293,6 +293,7 @@ rate_control_pid_get_rate(void *priv, struct ieee80211_sta *sta,

static void
rate_control_pid_rate_init(void *priv, struct ieee80211_supported_band *sband,
+ struct cfg80211_chan_def *chandef,
struct ieee80211_sta *sta, void *priv_sta)
{
struct rc_pid_sta_info *spinfo = priv_sta;
--
1.7.10.4


2013-06-27 16:59:16

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 08/18] mac80211: allow scanning for 5/10 MHz channels in IBSS

Use a chandef instead of just the channel for scanning, and enable
5/10 Mhz scanning for IBSS mode. Also reporting is changed to the new
inform_bss functions.

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>

---
Changes to PATCHv4:
* fix comments
---
net/mac80211/ibss.c | 16 ++++++++++++----
net/mac80211/ieee80211_i.h | 5 +++--
net/mac80211/main.c | 13 ++-----------
net/mac80211/scan.c | 45 ++++++++++++++++++++++++++++++++++++++------
4 files changed, 56 insertions(+), 23 deletions(-)

diff --git a/net/mac80211/ibss.c b/net/mac80211/ibss.c
index d0c27dc..6adc5af 100644
--- a/net/mac80211/ibss.c
+++ b/net/mac80211/ibss.c
@@ -51,6 +51,7 @@ static void __ieee80211_sta_join_ibss(struct ieee80211_sub_if_data *sdata,
u32 bss_change, rate_flags, rates = 0, rates_added = 0;
u8 supp_rates[IEEE80211_MAX_SUPP_RATES];
struct cfg80211_chan_def chandef;
+ enum nl80211_bss_scan_width scan_width;
struct beacon_data *presp;
int frame_len;
int shift;
@@ -267,8 +268,10 @@ static void __ieee80211_sta_join_ibss(struct ieee80211_sub_if_data *sdata,
mod_timer(&ifibss->timer,
round_jiffies(jiffies + IEEE80211_IBSS_MERGE_INTERVAL));

- bss = cfg80211_inform_bss_frame(local->hw.wiphy, chan,
- mgmt, presp->head_len, 0, GFP_KERNEL);
+ scan_width = cfg80211_chandef_to_scan_width(&chandef);
+ bss = cfg80211_inform_bss_width_frame(local->hw.wiphy, chan,
+ scan_width, mgmt,
+ presp->head_len, 0, GFP_KERNEL);
cfg80211_put_bss(local->hw.wiphy, bss);
netif_carrier_on(sdata->dev);
cfg80211_ibss_joined(sdata->dev, ifibss->bssid, GFP_KERNEL);
@@ -749,6 +752,7 @@ static int ieee80211_sta_active_ibss(struct ieee80211_sub_if_data *sdata)
static void ieee80211_sta_merge_ibss(struct ieee80211_sub_if_data *sdata)
{
struct ieee80211_if_ibss *ifibss = &sdata->u.ibss;
+ enum nl80211_bss_scan_width scan_width;

sdata_assert_lock(sdata);

@@ -770,8 +774,9 @@ static void ieee80211_sta_merge_ibss(struct ieee80211_sub_if_data *sdata)
sdata_info(sdata,
"No active IBSS STAs - trying to scan for other IBSS networks with same SSID (merge)\n");

+ scan_width = cfg80211_chandef_to_scan_width(&ifibss->chandef);
ieee80211_request_ibss_scan(sdata, ifibss->ssid, ifibss->ssid_len,
- NULL);
+ NULL, scan_width);
}

static void ieee80211_sta_create_ibss(struct ieee80211_sub_if_data *sdata)
@@ -821,6 +826,7 @@ static void ieee80211_sta_find_ibss(struct ieee80211_sub_if_data *sdata)
struct cfg80211_bss *cbss;
struct ieee80211_channel *chan = NULL;
const u8 *bssid = NULL;
+ enum nl80211_bss_scan_width scan_width;
int active_ibss;
u16 capability;

@@ -869,8 +875,10 @@ static void ieee80211_sta_find_ibss(struct ieee80211_sub_if_data *sdata)
IEEE80211_SCAN_INTERVAL)) {
sdata_info(sdata, "Trigger new scan to find an IBSS to join\n");

+ scan_width = cfg80211_chandef_to_scan_width(&ifibss->chandef);
ieee80211_request_ibss_scan(sdata, ifibss->ssid,
- ifibss->ssid_len, chan);
+ ifibss->ssid_len, chan,
+ scan_width);
} else {
int interval = IEEE80211_SCAN_INTERVAL;

diff --git a/net/mac80211/ieee80211_i.h b/net/mac80211/ieee80211_i.h
index 319ae0b..bd3ecfb 100644
--- a/net/mac80211/ieee80211_i.h
+++ b/net/mac80211/ieee80211_i.h
@@ -1053,7 +1053,7 @@ struct ieee80211_local {
struct cfg80211_ssid scan_ssid;
struct cfg80211_scan_request *int_scan_req;
struct cfg80211_scan_request *scan_req, *hw_scan_req;
- struct ieee80211_channel *scan_channel;
+ struct cfg80211_chan_def scan_chandef;
enum ieee80211_band hw_scan_band;
int scan_channel_idx;
int scan_ies_len;
@@ -1333,7 +1333,8 @@ void ieee80211_mesh_rx_queued_mgmt(struct ieee80211_sub_if_data *sdata,
void ieee80211_scan_work(struct work_struct *work);
int ieee80211_request_ibss_scan(struct ieee80211_sub_if_data *sdata,
const u8 *ssid, u8 ssid_len,
- struct ieee80211_channel *chan);
+ struct ieee80211_channel *chan,
+ enum nl80211_bss_scan_width scan_width);
int ieee80211_request_scan(struct ieee80211_sub_if_data *sdata,
struct cfg80211_scan_request *req);
void ieee80211_scan_cancel(struct ieee80211_local *local);
diff --git a/net/mac80211/main.c b/net/mac80211/main.c
index a1d51af..3e00871 100644
--- a/net/mac80211/main.c
+++ b/net/mac80211/main.c
@@ -102,17 +102,8 @@ static u32 ieee80211_hw_conf_chan(struct ieee80211_local *local)

offchannel_flag = local->hw.conf.flags & IEEE80211_CONF_OFFCHANNEL;

- if (local->scan_channel) {
- chandef.chan = local->scan_channel;
- /* If scanning on oper channel, use whatever channel-type
- * is currently in use.
- */
- if (chandef.chan == local->_oper_chandef.chan) {
- chandef = local->_oper_chandef;
- } else {
- chandef.width = NL80211_CHAN_WIDTH_20_NOHT;
- chandef.center_freq1 = chandef.chan->center_freq;
- }
+ if (local->scan_chandef.chan) {
+ chandef = local->scan_chandef;
} else if (local->tmp_channel) {
chandef.chan = local->tmp_channel;
chandef.width = NL80211_CHAN_WIDTH_20_NOHT;
diff --git a/net/mac80211/scan.c b/net/mac80211/scan.c
index b1bfb05..7285361 100644
--- a/net/mac80211/scan.c
+++ b/net/mac80211/scan.c
@@ -66,6 +66,7 @@ ieee80211_bss_info_update(struct ieee80211_local *local,
struct cfg80211_bss *cbss;
struct ieee80211_bss *bss;
int clen, srlen;
+ enum nl80211_bss_scan_width scan_width;
s32 signal = 0;

if (local->hw.flags & IEEE80211_HW_SIGNAL_DBM)
@@ -73,8 +74,15 @@ ieee80211_bss_info_update(struct ieee80211_local *local,
else if (local->hw.flags & IEEE80211_HW_SIGNAL_UNSPEC)
signal = (rx_status->signal * 100) / local->hw.max_signal;

- cbss = cfg80211_inform_bss_frame(local->hw.wiphy, channel,
- mgmt, len, signal, GFP_ATOMIC);
+ scan_width = NL80211_BSS_CHAN_WIDTH_20;
+ if (rx_status->flag & RX_FLAG_5MHZ)
+ scan_width = NL80211_BSS_CHAN_WIDTH_5;
+ if (rx_status->flag & RX_FLAG_10MHZ)
+ scan_width = NL80211_BSS_CHAN_WIDTH_10;
+
+ cbss = cfg80211_inform_bss_width_frame(local->hw.wiphy, channel,
+ scan_width, mgmt, len, signal,
+ GFP_ATOMIC);
if (!cbss)
return NULL;

@@ -291,7 +299,7 @@ static void __ieee80211_scan_completed(struct ieee80211_hw *hw, bool aborted,
rcu_assign_pointer(local->scan_sdata, NULL);

local->scanning = 0;
- local->scan_channel = NULL;
+ local->scan_chandef.chan = NULL;

/* Set power back to normal operating levels. */
ieee80211_hw_config(local, 0);
@@ -626,11 +634,34 @@ static void ieee80211_scan_state_set_channel(struct ieee80211_local *local,
{
int skip;
struct ieee80211_channel *chan;
+ enum nl80211_bss_scan_width oper_scan_width;

skip = 0;
chan = local->scan_req->channels[local->scan_channel_idx];

- local->scan_channel = chan;
+ local->scan_chandef.chan = chan;
+ local->scan_chandef.center_freq1 = chan->center_freq;
+ local->scan_chandef.center_freq2 = 0;
+ switch (local->scan_req->scan_width) {
+ case NL80211_BSS_CHAN_WIDTH_5:
+ local->scan_chandef.width = NL80211_CHAN_WIDTH_5;
+ break;
+ case NL80211_BSS_CHAN_WIDTH_10:
+ local->scan_chandef.width = NL80211_CHAN_WIDTH_10;
+ break;
+ case NL80211_BSS_CHAN_WIDTH_20:
+ /* If scanning on oper channel, use whatever channel-type
+ * is currently in use.
+ */
+ oper_scan_width = cfg80211_chandef_to_scan_width(
+ &local->_oper_chandef);
+ if (chan == local->_oper_chandef.chan &&
+ oper_scan_width == local->scan_req->scan_width)
+ local->scan_chandef = local->_oper_chandef;
+ else
+ local->scan_chandef.width = NL80211_CHAN_WIDTH_20_NOHT;
+ break;
+ }

if (ieee80211_hw_config(local, IEEE80211_CONF_CHANGE_CHANNEL))
skip = 1;
@@ -670,7 +701,7 @@ static void ieee80211_scan_state_suspend(struct ieee80211_local *local,
unsigned long *next_delay)
{
/* switch back to the operating channel */
- local->scan_channel = NULL;
+ local->scan_chandef.chan = NULL;
ieee80211_hw_config(local, IEEE80211_CONF_CHANGE_CHANNEL);

/* disable PS */
@@ -812,7 +843,8 @@ int ieee80211_request_scan(struct ieee80211_sub_if_data *sdata,

int ieee80211_request_ibss_scan(struct ieee80211_sub_if_data *sdata,
const u8 *ssid, u8 ssid_len,
- struct ieee80211_channel *chan)
+ struct ieee80211_channel *chan,
+ enum nl80211_bss_scan_width scan_width)
{
struct ieee80211_local *local = sdata->local;
int ret = -EBUSY;
@@ -862,6 +894,7 @@ int ieee80211_request_ibss_scan(struct ieee80211_sub_if_data *sdata,

local->int_scan_req->ssids = &local->scan_ssid;
local->int_scan_req->n_ssids = 1;
+ local->int_scan_req->scan_width = scan_width;
memcpy(local->int_scan_req->ssids[0].ssid, ssid, IEEE80211_MAX_SSID_LEN);
local->int_scan_req->ssids[0].ssid_len = ssid_len;

--
1.7.10.4


2013-06-27 16:59:15

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 11/18] ath9k: always use SIFS times from OFDM for 5/10 MHz

5/10 MHz channels should always use SIFS times as defined in IEEE
802.11-2012 18.4.4 (OFDM PHY characteristics). This makes it compatible
to ath5k, which does the same.

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
drivers/net/wireless/ath/ath9k/hw.c | 5 ++---
1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c
index 5324c33..b12cca4 100644
--- a/drivers/net/wireless/ath/ath9k/hw.c
+++ b/drivers/net/wireless/ath/ath9k/hw.c
@@ -1069,7 +1069,7 @@ void ath9k_hw_init_global_settings(struct ath_hw *ah)
if (IS_CHAN_A_FAST_CLOCK(ah, chan))
tx_lat += 11;

- sifstime *= 2;
+ sifstime = 32;
ack_offset = 16;
slottime = 13;
} else if (IS_CHAN_QUARTER_RATE(chan)) {
@@ -1079,7 +1079,7 @@ void ath9k_hw_init_global_settings(struct ath_hw *ah)
if (IS_CHAN_A_FAST_CLOCK(ah, chan))
tx_lat += 22;

- sifstime *= 4;
+ sifstime = 64;
ack_offset = 32;
slottime = 21;
} else {
@@ -1116,7 +1116,6 @@ void ath9k_hw_init_global_settings(struct ath_hw *ah)
ctstimeout += 48 - sifstime - ah->slottime;
}

-
ath9k_hw_set_sifs_time(ah, sifstime);
ath9k_hw_setslottime(ah, slottime);
ath9k_hw_set_ack_timeout(ah, acktimeout);
--
1.7.10.4


2013-06-27 16:59:15

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 07/18] mac80211: add radiotap flag and handling for 5/10 MHz

Wireshark already defines radiotap channel flags for 5 and 10 MHz, so
just use them in Linux radiotap too. Furthermore, add rx status flags to
allow drivers to report when they received data on 5 or 10 MHz channels.

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
include/net/ieee80211_radiotap.h | 4 ++++
include/net/mac80211.h | 4 ++++
net/mac80211/rx.c | 21 ++++++++++++---------
3 files changed, 20 insertions(+), 9 deletions(-)

diff --git a/include/net/ieee80211_radiotap.h b/include/net/ieee80211_radiotap.h
index c6d07cb..8b5b714 100644
--- a/include/net/ieee80211_radiotap.h
+++ b/include/net/ieee80211_radiotap.h
@@ -230,6 +230,10 @@ enum ieee80211_radiotap_type {
#define IEEE80211_CHAN_PASSIVE 0x0200 /* Only passive scan allowed */
#define IEEE80211_CHAN_DYN 0x0400 /* Dynamic CCK-OFDM channel */
#define IEEE80211_CHAN_GFSK 0x0800 /* GFSK channel (FHSS PHY) */
+#define IEEE80211_CHAN_GSM 0x1000 /* GSM (900 MHz) */
+#define IEEE80211_CHAN_STURBO 0x2000 /* Static Turbo */
+#define IEEE80211_CHAN_HALF 0x4000 /* Half channel (10 MHz wide) */
+#define IEEE80211_CHAN_QUARTER 0x8000 /* Quarter channel (5 MHz wide) */

/* For IEEE80211_RADIOTAP_FLAGS */
#define IEEE80211_RADIOTAP_F_CFP 0x01 /* sent/received
diff --git a/include/net/mac80211.h b/include/net/mac80211.h
index 9445f38..ed3dd96 100644
--- a/include/net/mac80211.h
+++ b/include/net/mac80211.h
@@ -809,6 +809,8 @@ ieee80211_tx_info_clear_status(struct ieee80211_tx_info *info)
* @RX_FLAG_AMPDU_DELIM_CRC_KNOWN: The delimiter CRC field is known (the CRC
* is stored in the @ampdu_delimiter_crc field)
* @RX_FLAG_STBC_MASK: STBC 2 bit bitmask. 1 - Nss=1, 2 - Nss=2, 3 - Nss=3
+ * @RX_FLAG_10MHZ: 10 MHz (half channel) was used
+ * @RX_FLAG_5MHZ: 5 MHz (quarter channel) was used
*/
enum mac80211_rx_flags {
RX_FLAG_MMIC_ERROR = BIT(0),
@@ -837,6 +839,8 @@ enum mac80211_rx_flags {
RX_FLAG_80P80MHZ = BIT(24),
RX_FLAG_160MHZ = BIT(25),
RX_FLAG_STBC_MASK = BIT(26) | BIT(27),
+ RX_FLAG_10MHZ = BIT(28),
+ RX_FLAG_5MHZ = BIT(29),
};

#define RX_FLAG_STBC_SHIFT 26
diff --git a/net/mac80211/rx.c b/net/mac80211/rx.c
index 90ab888..e62aca1 100644
--- a/net/mac80211/rx.c
+++ b/net/mac80211/rx.c
@@ -146,6 +146,7 @@ ieee80211_add_rx_radiotap_header(struct ieee80211_local *local,
struct ieee80211_radiotap_header *rthdr;
unsigned char *pos;
u16 rx_flags = 0;
+ u16 channel_flags = 0;
int mpdulen;

mpdulen = skb->len;
@@ -220,20 +221,22 @@ ieee80211_add_rx_radiotap_header(struct ieee80211_local *local,
/* IEEE80211_RADIOTAP_CHANNEL */
put_unaligned_le16(status->freq, pos);
pos += 2;
+ if (status->flag & RX_FLAG_10MHZ)
+ channel_flags |= IEEE80211_CHAN_HALF;
+ else if (status->flag & RX_FLAG_5MHZ)
+ channel_flags |= IEEE80211_CHAN_QUARTER;
+
if (status->band == IEEE80211_BAND_5GHZ)
- put_unaligned_le16(IEEE80211_CHAN_OFDM | IEEE80211_CHAN_5GHZ,
- pos);
+ channel_flags |= IEEE80211_CHAN_OFDM | IEEE80211_CHAN_5GHZ;
else if (status->flag & (RX_FLAG_HT | RX_FLAG_VHT))
- put_unaligned_le16(IEEE80211_CHAN_DYN | IEEE80211_CHAN_2GHZ,
- pos);
+ channel_flags |= IEEE80211_CHAN_DYN | IEEE80211_CHAN_2GHZ;
else if (rate && rate->flags & IEEE80211_RATE_ERP_G)
- put_unaligned_le16(IEEE80211_CHAN_OFDM | IEEE80211_CHAN_2GHZ,
- pos);
+ channel_flags |= IEEE80211_CHAN_OFDM | IEEE80211_CHAN_2GHZ;
else if (rate)
- put_unaligned_le16(IEEE80211_CHAN_CCK | IEEE80211_CHAN_2GHZ,
- pos);
+ channel_flags |= IEEE80211_CHAN_OFDM | IEEE80211_CHAN_2GHZ;
else
- put_unaligned_le16(IEEE80211_CHAN_2GHZ, pos);
+ channel_flags |= IEEE80211_CHAN_2GHZ;
+ put_unaligned_le16(channel_flags, pos);
pos += 2;

/* IEEE80211_RADIOTAP_DBM_ANTSIGNAL */
--
1.7.10.4


2013-06-27 16:59:12

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 03/18] mac80211: fix timing for 5 MHz and 10 MHz channels

according to IEEE 802.11-2012 section 18, various timings change
when using 5 MHz and 10 MHz. Reflect this by using a "shift" when
calculating durations.

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
Changes to PATCHv4:
* remove obsolete ieee80211_local_get_divisor()
* change divisor to shift to avoid unnecesary integer divisions

Changes to PATCHv3:
* don't use hw.conf
* remove net/mac80211/rc80211_minstrel_ht.c modifications
---
net/mac80211/ieee80211_i.h | 31 +++++++++++++++++++++++++++-
net/mac80211/rc80211_minstrel.c | 30 +++++++++++++++++++++------
net/mac80211/rc80211_minstrel_ht.c | 5 +++--
net/mac80211/tx.c | 10 ++++++---
net/mac80211/util.c | 39 ++++++++++++++++++++++++------------
5 files changed, 90 insertions(+), 25 deletions(-)

diff --git a/net/mac80211/ieee80211_i.h b/net/mac80211/ieee80211_i.h
index 0ccaaeb..45b19cc 100644
--- a/net/mac80211/ieee80211_i.h
+++ b/net/mac80211/ieee80211_i.h
@@ -808,6 +808,34 @@ ieee80211_get_sdata_band(struct ieee80211_sub_if_data *sdata)
return band;
}

+static inline int
+ieee80211_chandef_get_shift(struct cfg80211_chan_def *chandef)
+{
+ switch (local->hw.conf.chandef.width) {
+ case NL80211_CHAN_WIDTH_5:
+ return 2;
+ case NL80211_CHAN_WIDTH_10:
+ return 1;
+ default:
+ return 0;
+ }
+}
+
+static inline int
+ieee80211_vif_get_shift(struct ieee80211_vif *vif)
+{
+ struct ieee80211_chanctx_conf *chanctx_conf;
+ int shift = 0;
+
+ rcu_read_lock();
+ chanctx_conf = rcu_dereference(vif->chanctx_conf);
+ if (chanctx_conf)
+ shift = ieee80211_chandef_get_shift(&chanctx_conf->def);
+ rcu_read_unlock();
+
+ return shift;
+}
+
enum sdata_queue_type {
IEEE80211_SDATA_QUEUE_TYPE_FRAME = 0,
IEEE80211_SDATA_QUEUE_AGG_START = 1,
@@ -1464,7 +1492,8 @@ extern void *mac80211_wiphy_privid; /* for wiphy privid */
u8 *ieee80211_get_bssid(struct ieee80211_hdr *hdr, size_t len,
enum nl80211_iftype type);
int ieee80211_frame_duration(enum ieee80211_band band, size_t len,
- int rate, int erp, int short_preamble);
+ int rate, int erp, int short_preamble,
+ int shift);
void mac80211_ev_michael_mic_failure(struct ieee80211_sub_if_data *sdata, int keyidx,
struct ieee80211_hdr *hdr, const u8 *tsc,
gfp_t gfp);
diff --git a/net/mac80211/rc80211_minstrel.c b/net/mac80211/rc80211_minstrel.c
index 5b25966..a507376 100644
--- a/net/mac80211/rc80211_minstrel.c
+++ b/net/mac80211/rc80211_minstrel.c
@@ -382,14 +382,18 @@ minstrel_get_rate(void *priv, struct ieee80211_sta *sta,
static void
calc_rate_durations(enum ieee80211_band band,
struct minstrel_rate *d,
- struct ieee80211_rate *rate)
+ struct ieee80211_rate *rate,
+ struct cfg80211_chan_def *chandef)
{
int erp = !!(rate->flags & IEEE80211_RATE_ERP_G);
+ int shift = ieee80211_chandef_get_shift(chandef);

d->perfect_tx_time = ieee80211_frame_duration(band, 1200,
- rate->bitrate, erp, 1);
+ DIV_ROUND_UP(rate->bitrate, 1 << shift), erp, 1,
+ shift);
d->ack_time = ieee80211_frame_duration(band, 10,
- rate->bitrate, erp, 1);
+ DIV_ROUND_UP(rate->bitrate, 1 << shift), erp, 1,
+ shift);
}

static void
@@ -425,14 +429,17 @@ minstrel_rate_init(void *priv, struct ieee80211_supported_band *sband,
struct ieee80211_rate *ctl_rate;
unsigned int i, n = 0;
unsigned int t_slot = 9; /* FIXME: get real slot time */
+ u32 rate_flags;

mi->sta = sta;
mi->lowest_rix = rate_lowest_index(sband, sta);
ctl_rate = &sband->bitrates[mi->lowest_rix];
mi->sp_ack_dur = ieee80211_frame_duration(sband->band, 10,
ctl_rate->bitrate,
- !!(ctl_rate->flags & IEEE80211_RATE_ERP_G), 1);
+ !!(ctl_rate->flags & IEEE80211_RATE_ERP_G), 1,
+ ieee80211_chandef_get_shift(chandef));

+ rate_flags = ieee80211_chandef_rate_flags(&mp->hw->conf.chandef);
memset(mi->max_tp_rate, 0, sizeof(mi->max_tp_rate));
mi->max_prob_rate = 0;

@@ -441,15 +448,22 @@ minstrel_rate_init(void *priv, struct ieee80211_supported_band *sband,
unsigned int tx_time = 0, tx_time_cts = 0, tx_time_rtscts = 0;
unsigned int tx_time_single;
unsigned int cw = mp->cw_min;
+ int shift;

if (!rate_supported(sta, sband->band, i))
continue;
+ if ((rate_flags & sband->bitrates[i].flags) != rate_flags)
+ continue;
+
n++;
memset(mr, 0, sizeof(*mr));

mr->rix = i;
- mr->bitrate = sband->bitrates[i].bitrate / 5;
- calc_rate_durations(sband->band, mr, &sband->bitrates[i]);
+ shift = ieee80211_chandef_get_shift(chandef);
+ mr->bitrate = DIV_ROUND_UP(sband->bitrates[i].bitrate,
+ (1 << shift) * 5);
+ calc_rate_durations(sband->band, mr, &sband->bitrates[i],
+ chandef);

/* calculate maximum number of retransmissions before
* fallback (based on maximum segment size) */
@@ -547,6 +561,7 @@ minstrel_init_cck_rates(struct minstrel_priv *mp)
{
static const int bitrates[4] = { 10, 20, 55, 110 };
struct ieee80211_supported_band *sband;
+ u32 rate_flags = ieee80211_chandef_rate_flags(&mp->hw->conf.chandef);
int i, j;

sband = mp->hw->wiphy->bands[IEEE80211_BAND_2GHZ];
@@ -559,6 +574,9 @@ minstrel_init_cck_rates(struct minstrel_priv *mp)
if (rate->flags & IEEE80211_RATE_ERP_G)
continue;

+ if ((rate_flags & sband->bitrates[i].flags) != rate_flags)
+ continue;
+
for (j = 0; j < ARRAY_SIZE(bitrates); j++) {
if (rate->bitrate != bitrates[j])
continue;
diff --git a/net/mac80211/rc80211_minstrel_ht.c b/net/mac80211/rc80211_minstrel_ht.c
index 5256297..7475a7a 100644
--- a/net/mac80211/rc80211_minstrel_ht.c
+++ b/net/mac80211/rc80211_minstrel_ht.c
@@ -862,8 +862,9 @@ minstrel_ht_update_caps(void *priv, struct ieee80211_supported_band *sband,
mi->sta = sta;
mi->stats_update = jiffies;

- ack_dur = ieee80211_frame_duration(sband->band, 10, 60, 1, 1);
- mi->overhead = ieee80211_frame_duration(sband->band, 0, 60, 1, 1) + ack_dur;
+ ack_dur = ieee80211_frame_duration(sband->band, 10, 60, 1, 1, 0);
+ mi->overhead = ieee80211_frame_duration(sband->band, 0, 60, 1, 1, 0);
+ mi->overhead += ack_dur;
mi->overhead_rtscts = mi->overhead + 2 * ack_dur;

mi->avg_ampdu_len = MINSTREL_FRAC(1, 1);
diff --git a/net/mac80211/tx.c b/net/mac80211/tx.c
index 4105d0c..3523daa 100644
--- a/net/mac80211/tx.c
+++ b/net/mac80211/tx.c
@@ -40,7 +40,7 @@ static __le16 ieee80211_duration(struct ieee80211_tx_data *tx,
struct sk_buff *skb, int group_addr,
int next_frag_len)
{
- int rate, mrate, erp, dur, i;
+ int rate, mrate, erp, dur, i, shift;
struct ieee80211_rate *txrate;
struct ieee80211_local *local = tx->local;
struct ieee80211_supported_band *sband;
@@ -153,6 +153,8 @@ static __le16 ieee80211_duration(struct ieee80211_tx_data *tx,
rate = mrate;
}

+ shift = ieee80211_vif_get_shift(&tx->sdata->vif);
+
/* Don't calculate ACKs for QoS Frames with NoAck Policy set */
if (ieee80211_is_data_qos(hdr->frame_control) &&
*(ieee80211_get_qos_ctl(hdr)) & IEEE80211_QOS_CTL_ACK_POLICY_NOACK)
@@ -162,7 +164,8 @@ static __le16 ieee80211_duration(struct ieee80211_tx_data *tx,
* (10 bytes + 4-byte FCS = 112 bits) plus SIFS; rounded up
* to closest integer */
dur = ieee80211_frame_duration(sband->band, 10, rate, erp,
- tx->sdata->vif.bss_conf.use_short_preamble);
+ tx->sdata->vif.bss_conf.use_short_preamble,
+ shift);

if (next_frag_len) {
/* Frame is fragmented: duration increases with time needed to
@@ -171,7 +174,8 @@ static __le16 ieee80211_duration(struct ieee80211_tx_data *tx,
/* next fragment */
dur += ieee80211_frame_duration(sband->band, next_frag_len,
txrate->bitrate, erp,
- tx->sdata->vif.bss_conf.use_short_preamble);
+ tx->sdata->vif.bss_conf.use_short_preamble,
+ shift);
}

return cpu_to_le16(dur);
diff --git a/net/mac80211/util.c b/net/mac80211/util.c
index 2265445..61856e1 100644
--- a/net/mac80211/util.c
+++ b/net/mac80211/util.c
@@ -107,7 +107,8 @@ void ieee80211_tx_set_protected(struct ieee80211_tx_data *tx)
}

int ieee80211_frame_duration(enum ieee80211_band band, size_t len,
- int rate, int erp, int short_preamble)
+ int rate, int erp, int short_preamble,
+ int shift)
{
int dur;

@@ -118,6 +119,9 @@ int ieee80211_frame_duration(enum ieee80211_band band, size_t len,
*
* rate is in 100 kbps, so divident is multiplied by 10 in the
* DIV_ROUND_UP() operations.
+ *
+ * shift may be 2 for 5 MHz channels or 1 for 10 MHz channels, and
+ * is assumed to be 0 otherwise.
*/

if (band == IEEE80211_BAND_5GHZ || erp) {
@@ -130,15 +134,21 @@ int ieee80211_frame_duration(enum ieee80211_band band, size_t len,
* TXTIME = T_PREAMBLE + T_SIGNAL + T_SYM x N_SYM + Signal Ext
*
* T_SYM = 4 usec
- * 802.11a - 17.5.2: aSIFSTime = 16 usec
+ * 802.11a - 18.5.2: aSIFSTime = 16 usec
* 802.11g - 19.8.4: aSIFSTime = 10 usec +
* signal ext = 6 usec
*/
dur = 16; /* SIFS + signal ext */
- dur += 16; /* 17.3.2.3: T_PREAMBLE = 16 usec */
- dur += 4; /* 17.3.2.3: T_SIGNAL = 4 usec */
+ dur += 16; /* IEEE 802.11-2012 18.3.2.4: T_PREAMBLE = 16 usec */
+ dur += 4; /* IEEE 802.11-2012 18.3.2.4: T_SIGNAL = 4 usec */
dur += 4 * DIV_ROUND_UP((16 + 8 * (len + 4) + 6) * 10,
4 * rate); /* T_SYM x N_SYM */
+
+ /* IEEE 802.11-2012 18.3.2.4: all values above are:
+ * * times 4 for 5 MHz
+ * * times 2 for 10 MHz
+ */
+ dur *= 1 << shift;
} else {
/*
* 802.11b or 802.11g with 802.11b compatibility:
@@ -168,7 +178,7 @@ __le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
{
struct ieee80211_sub_if_data *sdata;
u16 dur;
- int erp;
+ int erp, shift = 0;
bool short_preamble = false;

erp = 0;
@@ -177,10 +187,11 @@ __le16 ieee80211_generic_frame_duration(struct ieee80211_hw *hw,
short_preamble = sdata->vif.bss_conf.use_short_preamble;
if (sdata->flags & IEEE80211_SDATA_OPERATING_GMODE)
erp = rate->flags & IEEE80211_RATE_ERP_G;
+ shift = ieee80211_vif_get_shift(vif);
}

dur = ieee80211_frame_duration(band, frame_len, rate->bitrate, erp,
- short_preamble);
+ short_preamble, shift);

return cpu_to_le16(dur);
}
@@ -194,7 +205,7 @@ __le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
struct ieee80211_rate *rate;
struct ieee80211_sub_if_data *sdata;
bool short_preamble;
- int erp;
+ int erp, shift = 0;
u16 dur;
struct ieee80211_supported_band *sband;

@@ -210,17 +221,18 @@ __le16 ieee80211_rts_duration(struct ieee80211_hw *hw,
short_preamble = sdata->vif.bss_conf.use_short_preamble;
if (sdata->flags & IEEE80211_SDATA_OPERATING_GMODE)
erp = rate->flags & IEEE80211_RATE_ERP_G;
+ shift = ieee80211_vif_get_shift(vif);
}

/* CTS duration */
dur = ieee80211_frame_duration(sband->band, 10, rate->bitrate,
- erp, short_preamble);
+ erp, short_preamble, shift);
/* Data frame duration */
dur += ieee80211_frame_duration(sband->band, frame_len, rate->bitrate,
- erp, short_preamble);
+ erp, short_preamble, shift);
/* ACK duration */
dur += ieee80211_frame_duration(sband->band, 10, rate->bitrate,
- erp, short_preamble);
+ erp, short_preamble, shift);

return cpu_to_le16(dur);
}
@@ -235,7 +247,7 @@ __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
struct ieee80211_rate *rate;
struct ieee80211_sub_if_data *sdata;
bool short_preamble;
- int erp;
+ int erp, shift = 0;
u16 dur;
struct ieee80211_supported_band *sband;

@@ -250,15 +262,16 @@ __le16 ieee80211_ctstoself_duration(struct ieee80211_hw *hw,
short_preamble = sdata->vif.bss_conf.use_short_preamble;
if (sdata->flags & IEEE80211_SDATA_OPERATING_GMODE)
erp = rate->flags & IEEE80211_RATE_ERP_G;
+ shift = ieee80211_vif_get_shift(vif);
}

/* Data frame duration */
dur = ieee80211_frame_duration(sband->band, frame_len, rate->bitrate,
- erp, short_preamble);
+ erp, short_preamble, shift);
if (!(frame_txctl->flags & IEEE80211_TX_CTL_NO_ACK)) {
/* ACK duration */
dur += ieee80211_frame_duration(sband->band, 10, rate->bitrate,
- erp, short_preamble);
+ erp, short_preamble, shift);
}

return cpu_to_le16(dur);
--
1.7.10.4


2013-06-27 16:59:18

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 14/18] ath9k: set 5/10 MHz supported channels and fix bitrate

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
Changes to PATCHv4:
* remove unused divisor line in the rate control
---
drivers/net/wireless/ath/ath9k/init.c | 24 ++++++++++++++++--------
drivers/net/wireless/ath/ath9k/rc.c | 5 +++++
2 files changed, 21 insertions(+), 8 deletions(-)

diff --git a/drivers/net/wireless/ath/ath9k/init.c b/drivers/net/wireless/ath/ath9k/init.c
index d0d3d2a..96b0d29 100644
--- a/drivers/net/wireless/ath/ath9k/init.c
+++ b/drivers/net/wireless/ath/ath9k/init.c
@@ -146,14 +146,22 @@ static struct ieee80211_rate ath9k_legacy_rates[] = {
RATE(20, 0x1a, IEEE80211_RATE_SHORT_PREAMBLE),
RATE(55, 0x19, IEEE80211_RATE_SHORT_PREAMBLE),
RATE(110, 0x18, IEEE80211_RATE_SHORT_PREAMBLE),
- RATE(60, 0x0b, 0),
- RATE(90, 0x0f, 0),
- RATE(120, 0x0a, 0),
- RATE(180, 0x0e, 0),
- RATE(240, 0x09, 0),
- RATE(360, 0x0d, 0),
- RATE(480, 0x08, 0),
- RATE(540, 0x0c, 0),
+ RATE(60, 0x0b, (IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ)),
+ RATE(90, 0x0f, (IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ)),
+ RATE(120, 0x0a, (IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ)),
+ RATE(180, 0x0e, (IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ)),
+ RATE(240, 0x09, (IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ)),
+ RATE(360, 0x0d, (IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ)),
+ RATE(480, 0x08, (IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ)),
+ RATE(540, 0x0c, (IEEE80211_RATE_SUPPORTS_5MHZ |
+ IEEE80211_RATE_SUPPORTS_10MHZ)),
};

#ifdef CONFIG_MAC80211_LEDS
diff --git a/drivers/net/wireless/ath/ath9k/rc.c b/drivers/net/wireless/ath/ath9k/rc.c
index e41f563..5a69d9b 100644
--- a/drivers/net/wireless/ath/ath9k/rc.c
+++ b/drivers/net/wireless/ath/ath9k/rc.c
@@ -1282,9 +1282,14 @@ static void ath_rate_init(void *priv, struct ieee80211_supported_band *sband,
struct ath_common *common = ath9k_hw_common(sc->sc_ah);
struct ath_rate_priv *ath_rc_priv = priv_sta;
int i, j = 0;
+ u32 rate_flags = ieee80211_chandef_rate_flags(&sc->hw->conf.chandef);

for (i = 0; i < sband->n_bitrates; i++) {
if (sta->supp_rates[sband->band] & BIT(i)) {
+ if ((rate_flags & sband->bitrates[i].flags)
+ != rate_flags)
+ continue;
+
ath_rc_priv->neg_rates.rs_rates[j]
= (sband->bitrates[i].bitrate * 2) / 10;
j++;
--
1.7.10.4


2013-06-27 16:59:18

by Simon Wunderlich

[permalink] [raw]
Subject: [PATCHv5 18/18] ath5k: enable support for 5 MHz and 10 MHz channels

Signed-off-by: Simon Wunderlich <[email protected]>
Signed-off-by: Mathias Kretschmer <[email protected]>
---
drivers/net/wireless/ath/ath5k/ath5k.h | 1 +
drivers/net/wireless/ath/ath5k/base.c | 25 ++++++++++++++++++++++---
drivers/net/wireless/ath/ath5k/base.h | 2 +-
drivers/net/wireless/ath/ath5k/mac80211-ops.c | 2 +-
4 files changed, 25 insertions(+), 5 deletions(-)

diff --git a/drivers/net/wireless/ath/ath5k/ath5k.h b/drivers/net/wireless/ath/ath5k/ath5k.h
index 2d691b8..74bd54d 100644
--- a/drivers/net/wireless/ath/ath5k/ath5k.h
+++ b/drivers/net/wireless/ath/ath5k/ath5k.h
@@ -29,6 +29,7 @@
#include <linux/average.h>
#include <linux/leds.h>
#include <net/mac80211.h>
+#include <net/cfg80211.h>

/* RX/TX descriptor hw structs
* TODO: Driver part should only see sw structs */
diff --git a/drivers/net/wireless/ath/ath5k/base.c b/drivers/net/wireless/ath/ath5k/base.c
index 7c298af..48161ed 100644
--- a/drivers/net/wireless/ath/ath5k/base.c
+++ b/drivers/net/wireless/ath/ath5k/base.c
@@ -56,6 +56,7 @@
#include <linux/etherdevice.h>
#include <linux/nl80211.h>

+#include <net/cfg80211.h>
#include <net/ieee80211_radiotap.h>

#include <asm/unaligned.h>
@@ -443,11 +444,27 @@ ath5k_setup_bands(struct ieee80211_hw *hw)
* Called with ah->lock.
*/
int
-ath5k_chan_set(struct ath5k_hw *ah, struct ieee80211_channel *chan)
+ath5k_chan_set(struct ath5k_hw *ah, struct cfg80211_chan_def *chandef)
{
ATH5K_DBG(ah, ATH5K_DEBUG_RESET,
"channel set, resetting (%u -> %u MHz)\n",
- ah->curchan->center_freq, chan->center_freq);
+ ah->curchan->center_freq, chandef->chan->center_freq);
+
+ switch (chandef->width) {
+ case NL80211_CHAN_WIDTH_20:
+ case NL80211_CHAN_WIDTH_20_NOHT:
+ ah->ah_bwmode = AR5K_BWMODE_DEFAULT;
+ break;
+ case NL80211_CHAN_WIDTH_5:
+ ah->ah_bwmode = AR5K_BWMODE_5MHZ;
+ break;
+ case NL80211_CHAN_WIDTH_10:
+ ah->ah_bwmode = AR5K_BWMODE_10MHZ;
+ break;
+ default:
+ WARN_ON(1);
+ return -EINVAL;
+ }

/*
* To switch channels clear any pending DMA operations;
@@ -455,7 +472,7 @@ ath5k_chan_set(struct ath5k_hw *ah, struct ieee80211_channel *chan)
* hardware at the new frequency, and then re-enable
* the relevant bits of the h/w.
*/
- return ath5k_reset(ah, chan, true);
+ return ath5k_reset(ah, chandef->chan, true);
}

void ath5k_vif_iter(void *data, u8 *mac, struct ieee80211_vif *vif)
@@ -2525,6 +2542,8 @@ ath5k_init_ah(struct ath5k_hw *ah, const struct ath_bus_ops *bus_ops)
/* SW support for IBSS_RSN is provided by mac80211 */
hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN;

+ hw->wiphy->flags |= WIPHY_FLAG_SUPPORTS_5_10_MHZ;
+
/* both antennas can be configured as RX or TX */
hw->wiphy->available_antennas_tx = 0x3;
hw->wiphy->available_antennas_rx = 0x3;
diff --git a/drivers/net/wireless/ath/ath5k/base.h b/drivers/net/wireless/ath/ath5k/base.h
index ca9a83c..97469d0 100644
--- a/drivers/net/wireless/ath/ath5k/base.h
+++ b/drivers/net/wireless/ath/ath5k/base.h
@@ -101,7 +101,7 @@ void ath5k_set_beacon_filter(struct ieee80211_hw *hw, bool enable);

void ath5k_update_bssid_mask_and_opmode(struct ath5k_hw *ah,
struct ieee80211_vif *vif);
-int ath5k_chan_set(struct ath5k_hw *ah, struct ieee80211_channel *chan);
+int ath5k_chan_set(struct ath5k_hw *ah, struct cfg80211_chan_def *chandef);
void ath5k_txbuf_free_skb(struct ath5k_hw *ah, struct ath5k_buf *bf);
void ath5k_rxbuf_free_skb(struct ath5k_hw *ah, struct ath5k_buf *bf);
void ath5k_tx_queue(struct ieee80211_hw *hw, struct sk_buff *skb,
diff --git a/drivers/net/wireless/ath/ath5k/mac80211-ops.c b/drivers/net/wireless/ath/ath5k/mac80211-ops.c
index 81b686c..aa9d976 100644
--- a/drivers/net/wireless/ath/ath5k/mac80211-ops.c
+++ b/drivers/net/wireless/ath/ath5k/mac80211-ops.c
@@ -202,7 +202,7 @@ ath5k_config(struct ieee80211_hw *hw, u32 changed)
mutex_lock(&ah->lock);

if (changed & IEEE80211_CONF_CHANGE_CHANNEL) {
- ret = ath5k_chan_set(ah, conf->chandef.chan);
+ ret = ath5k_chan_set(ah, &conf->chandef);
if (ret < 0)
goto unlock;
}
--
1.7.10.4


2013-07-05 13:16:01

by Johannes Berg

[permalink] [raw]
Subject: Re: [PATCHv5 03/18] mac80211: fix timing for 5 MHz and 10 MHz channels

On Thu, 2013-06-27 at 18:58 +0200, Simon Wunderlich wrote:

> * change divisor to shift to avoid unnecesary integer divisions

That didn't really do much ;-)

> d->perfect_tx_time = ieee80211_frame_duration(band, 1200,
> - rate->bitrate, erp, 1);
> + DIV_ROUND_UP(rate->bitrate, 1 << shift), erp, 1,

That's still the integer division, unless the compiler can do something
about it?

> + DIV_ROUND_UP(rate->bitrate, 1 << shift), erp, 1,

ditto

> + mr->bitrate = DIV_ROUND_UP(sband->bitrates[i].bitrate,
> + (1 << shift) * 5);

That looks even weirder?

> + /* IEEE 802.11-2012 18.3.2.4: all values above are:
> + * * times 4 for 5 MHz
> + * * times 2 for 10 MHz
> + */
> + dur *= 1 << shift;

Isn't that just "dur <<= shift"?

I think "DIV_ROUND_UP(x, 1 << shift)" can probably be written more
efficiently? Unless the compiler will do something by itself?

Something like

DIV_ROUND_UP(x, 1<<shift) == (x + (1<<shift) -1) >> shift

I think?

OK, it looks like if "x" is *unsigned* then the compiler will do this,
but with *signed* values it can't actually know because for negative
values it's obviously not actually equivalent.

johannes


2013-07-08 11:03:48

by Johannes Berg

[permalink] [raw]
Subject: Re: [PATCHv5 00/18] Add support for 5 and 10 MHz channels

On Thu, 2013-06-27 at 18:58 +0200, Simon Wunderlich wrote:

> As always, any comments are appreciated!

Compilation is broken in the middle of this series so I'm dropping this.

joahnnes


2013-07-08 14:37:20

by Simon Wunderlich

[permalink] [raw]
Subject: Re: [PATCHv5 00/18] Add support for 5 and 10 MHz channels

On Mon, Jul 08, 2013 at 01:03:41PM +0200, Johannes Berg wrote:
> On Thu, 2013-06-27 at 18:58 +0200, Simon Wunderlich wrote:
>
> > As always, any comments are appreciated!
>
> Compilation is broken in the middle of this series so I'm dropping this.

Whoops, you are right. I'll send a fixed patchset later, also including the
whitespace left-over you've noticed. I'll leave the DIV_ROUND_UP() as it is
though, as we discusseed.

Thanks,
Simon


Attachments:
(No filename) (445.00 B)
signature.asc (198.00 B)
Digital signature
Download all attachments

2013-07-05 13:17:49

by Johannes Berg

[permalink] [raw]
Subject: Re: [PATCHv5 04/18] mac80211: select and adjust bitrates according to channel mode

>
> +
> +
> +
> static int sta_apply_parameters(struct ieee80211_local *local,

Hmm? :)

johannes