From: Eliad Peller <[email protected]>
* enable mmc3 used for wlan
* configure the gpios used for wlan
* add fixed voltage regulator used for wlan power control
Signed-off-by: Eliad Peller <[email protected]>
Signed-off-by: Yaniv Machani <[email protected]>
---
arch/arm/boot/dts/am335x-evm.dts | 68 ++++++++++++++++++++++++++++++++++++++
1 files changed, 68 insertions(+), 0 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index dd03a2b..b690674 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -8,6 +8,7 @@
/dts-v1/;
#include "am33xx.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "TI AM335x EVM";
@@ -38,6 +39,20 @@
regulator-boot-on;
};
+ wlan_en_reg: fixedregulator@2 {
+ compatible = "regulator-fixed";
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ /* WLAN_EN GPIO for this board - Bank3, pin16 */
+ gpio = <&gpio1 16 0>;
+
+ /* WLAN card specific delay */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+
matrix_keypad: matrix_keypad@0 {
compatible = "gpio-matrix-keypad";
debounce-delay-ms = <5>;
@@ -266,6 +281,27 @@
>;
};
+ /* wl12xx/wl18xx card on mmc3 */
+ mmc3_pins: pinmux_mmc3_pins {
+ pinctrl-single,pins = <
+ 0x44 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a1.mmc2_dat0, INPUT_PULLUP | MODE3 */
+ 0x48 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a2.mmc2_dat1, INPUT_PULLUP | MODE3 */
+ 0x4C (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a3.mmc2_dat2, INPUT_PULLUP | MODE3 */
+ 0x78 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_ben1.mmc2_dat3, INPUT_PULLUP | MODE3 */
+ 0x88 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_csn3.mmc2_cmd, INPUT_PULLUP | MODE3 */
+ 0x8C (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_clk.mmc2_clk, INPUT_PULLUP | MODE3 */
+ >;
+ };
+
+ /* wl12xx/wl18xx card enable/irq GPIOs. */
+ wlan_pins: pinmux_wlan_pins {
+ pinctrl-single,pins = <
+ 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a0.gpio1_16 */
+ 0x19C (PIN_INPUT | MUX_MODE7) /* mcasp0_ahclkr.gpio3_17 */
+ 0x1AC (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* mcasp0_ahclkx.gpio3_21 */
+ >;
+ };
+
lcd_pins_s0: lcd_pins_s0 {
pinctrl-single,pins = <
0x20 (PIN_OUTPUT | MUX_MODE1) /* gpmc_ad8.lcd_data23 */
@@ -665,6 +701,38 @@
cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
};
+&mmc3 {
+ /* these are on the crossbar and are outlined in the
+ xbar-event-map element */
+ dmas = <&edma 12
+ &edma 13>;
+ dma-names = "tx", "rx";
+ status = "okay";
+ vmmc-supply = <&wlan_en_reg>;
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins &wlan_pins>;
+ ti,non-removable;
+ ti,needs-special-hs-handling;
+ cap-power-off-card;
+ keep-power-in-suspend;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wlcore: wlcore@2 {
+ compatible = "ti,wl1835";
+ reg = <2>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
+ ref-clock-frequency = <38400000>;
+ };
+};
+
+&edma {
+ ti,edma-xbar-event-map = /bits/ 16 <1 12
+ 2 13>;
+};
+
&sham {
status = "okay";
};
--
1.7.9
From: Eliad Peller <[email protected]>
uart1 is used for shared transport (used for multiplexing
bluetooth and nfc data). add the needed muxes and definitions.
Signed-off-by: Eliad Peller <[email protected]>
Signed-off-by: Eyal Reizer <[email protected]>
---
arch/arm/boot/dts/am335x-evm.dts | 29 +++++++++++++++++++++++++++++
1 files changed, 29 insertions(+), 0 deletions(-)
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index b690674..a0a3f72 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -135,6 +135,18 @@
};
};
+ kim {
+ compatible = "kim";
+ nshutdown_gpio = <117>; /* Bank3, pin21 */
+ dev_name = "/dev/ttyO1";
+ flow_cntrl = <1>;
+ baud_rate = <3000000>;
+ };
+
+ btwilink {
+ compatible = "btwilink";
+ };
+
sound {
compatible = "ti,da830-evm-audio";
ti,model = "AM335x-EVM";
@@ -191,6 +203,16 @@
>;
};
+ uart1_pins: pinmux_uart1_pins {
+ pinctrl-single,pins = <
+ 0x178 (PIN_INPUT | MUX_MODE0) /* uart1_ctsn.uart1_ctsn */
+ 0x17C (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_rtsn.uart1_rtsn */
+ 0x180 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart1_rxd.uart1_rxd */
+ 0x184 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* uart1_txd.uart1_txd */
+ >;
+ };
+
+
clkout2_pin: pinmux_clkout2_pin {
pinctrl-single,pins = <
0x1b4 (PIN_OUTPUT_PULLDOWN | MUX_MODE3) /* xdma_event_intr1.clkout2 */
@@ -359,6 +381,13 @@
status = "okay";
};
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+
+ status = "okay";
+};
+
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
--
1.7.9