2022-01-12 22:19:54

by Baochen Qiang

Subject: [PATCH v2] ath11k: Reconfigure hardware rate for WCN6855 after vdev is started

There is an issue that WCN6855 tries to connect to an AP using
a hardware rate of 1Mb/s , even though the AP has announced
expected rates as [24, 36, 48, 54] in Probe Response frame.

The reason is that WCN6855 firmware clears hardware rate info
of management frames when vdev starts and uses 1Mb/s as default.
To solve it, reconfigure the rate after vdev is started.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1

Signed-off-by: Baochen Qiang <[email protected]>
---
v2:
Rebased on latest ath.git.

drivers/net/wireless/ath/ath11k/core.h | 1 +
drivers/net/wireless/ath/ath11k/mac.c | 18 ++++++++++++++++++
2 files changed, 19 insertions(+)

diff --git a/drivers/net/wireless/ath/ath11k/core.h b/drivers/net/wireless/ath/ath11k/core.h
index 9e88ccca5ca7..4eda15c56b04 100644
--- a/drivers/net/wireless/ath/ath11k/core.h
+++ b/drivers/net/wireless/ath/ath11k/core.h
@@ -603,6 +603,7 @@ struct ath11k {
struct completion finish_11d_ch_list;
bool pending_11d;
bool regdom_set_by_user;
+ int hw_rate_code;
};

struct ath11k_band_cap {
diff --git a/drivers/net/wireless/ath/ath11k/mac.c b/drivers/net/wireless/ath/ath11k/mac.c
index 07f499d5ec92..0d8e20d89988 100644
--- a/drivers/net/wireless/ath/ath11k/mac.c
+++ b/drivers/net/wireless/ath/ath11k/mac.c
@@ -2862,6 +2862,11 @@ static void ath11k_recalculate_mgmt_rate(struct ath11k *ar,
if (ret)
ath11k_warn(ar->ab, "failed to set mgmt tx rate %d\n", ret);

+ /* For WCN6855, firmware will clear this param when vdev starts, hence
+ * cache it here so that we can reconfigure it once vdev starts.
+ */
+ ar->hw_rate_code = hw_rate_code;
+
vdev_param = WMI_VDEV_PARAM_BEACON_RATE;
ret = ath11k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id, vdev_param,
hw_rate_code);
@@ -6955,6 +6960,19 @@ static int ath11k_start_vdev_delay(struct ieee80211_hw *hw,
return ret;
}

+ /* Reconfigure hardware rate code since it is cleared by firmware.
+ */
+ if (ar->hw_rate_code > 0) {
+ u32 vdev_param = WMI_VDEV_PARAM_MGMT_RATE;
+
+ ret = ath11k_wmi_vdev_set_param_cmd(ar, arvif->vdev_id, vdev_param,
+ ar->hw_rate_code);
+ if (ret) {
+ ath11k_warn(ar->ab, "failed to set mgmt tx rate %d\n", ret);
+ return ret;
+ }
+ }
+
if (arvif->vdev_type == WMI_VDEV_TYPE_MONITOR) {
ret = ath11k_wmi_vdev_up(ar, arvif->vdev_id, 0, ar->mac_addr);
if (ret) {
--
2.25.1

2022-01-18 02:25:04

by Kalle Valo

Subject: Re: [PATCH v2] ath11k: Reconfigure hardware rate for WCN6855 after vdev is started

Baochen Qiang <[email protected]> wrote:

> There is an issue that WCN6855 tries to connect to an AP using
> a hardware rate of 1Mb/s , even though the AP has announced
> expected rates as [24, 36, 48, 54] in Probe Response frame.
>
> The reason is that WCN6855 firmware clears hardware rate info
> of management frames when vdev starts and uses 1Mb/s as default.
> To solve it, reconfigure the rate after vdev is started.
>
> Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
>
> Signed-off-by: Baochen Qiang <[email protected]>
> Signed-off-by: Kalle Valo <[email protected]>

Patch applied to ath-next branch of ath.git, thanks.

dc7ff75690ea ath11k: Reconfigure hardware rate for WCN6855 after vdev is started

--
https://patchwork.kernel.org/project/linux-wireless/patch/[email protected]/

https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches