Return-path: Received: from main.gmane.org ([80.91.229.2]:45868 "EHLO ciao.gmane.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752270AbYIHGOP (ORCPT ); Mon, 8 Sep 2008 02:14:15 -0400 Received: from list by ciao.gmane.org with local (Exim 4.43) id 1Kca0q-0004sx-5e for linux-wireless@vger.kernel.org; Mon, 08 Sep 2008 06:14:12 +0000 Received: from 77.21.170.83 ([77.21.170.83]) by main.gmane.org with esmtp (Gmexim 0.1 (Debian)) id 1AlnuQ-0007hv-00 for ; Mon, 08 Sep 2008 06:14:12 +0000 Received: from feldmann_markus by 77.21.170.83 with local (Gmexim 0.1 (Debian)) id 1AlnuQ-0007hv-00 for ; Mon, 08 Sep 2008 06:14:12 +0000 To: linux-wireless@vger.kernel.org From: feldmaus Subject: Do not get BCM4303 to work Date: Mon, 08 Sep 2008 08:15:51 +0200 Message-ID: (sfid-20080908_081419_189737_2796EF81) Mime-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-15; format=flowed Sender: linux-wireless-owner@vger.kernel.org List-ID: Hi All, i do not get my Wlan Card with BCM4303 Chip to work. My System is Debian Testing 32-bit with Kernel 2.6.25-2 from Debian, therefore i am using the Driver b43legacy. I tried to connect this Wlan Card with my Wireless Printer. It is a Ad-Hoc Connection with, SSID=3Dkleopatra Channel=3D10 Authentification=3Dnon Encryption=3D128-bit Wep Here it comes the Outout from , 02:02.0 Network controller: Broadcom Corporation BCM4303 802.11b Wireless LAN Controller (rev 02) Subsystem: Hewlett-Packard Company Device 12f3 Flags: bus master, fast devsel, latency 64, IRQ 17 Memory at e0104000 (32-bit, non-prefetchable) [size=3D8K] Kernel driver in use: b43-pci-bridge Kernel modules: ssb I tried some Howtos, but it didn't work. show's the following, eth0 Link encap:Ethernet Hardware Adresse 00:0f:b0:0e:57:a1 inet Adresse:77.21.170.83 Bcast:255.255.255.255 Maske:255.255.252.0 UP BROADCAST RUNNING MULTICAST MTU:576 Metrik:1 RX packets:35420 errors:0 dropped:0 overruns:0 frame:0 TX packets:1946 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenl=E4nge:1000 RX bytes:3756084 (3.5 MiB) TX bytes:245214 (239.4 KiB) Interrupt:18 Basisadresse:0x7000 lo Link encap:Lokale Schleife inet Adresse:127.0.0.1 Maske:255.0.0.0 inet6-Adresse: ::1/128 G=FCltigkeitsbereich:Maschine UP LOOPBACK RUNNING MTU:16436 Metrik:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:10 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenl=E4nge:0 RX bytes:660 (660.0 B) TX bytes:660 (660.0 B) wlan0 Link encap:Ethernet Hardware Adresse 00:90:4b:97:34:73 UP BROADCAST MULTICAST MTU:1500 Metrik:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenl=E4nge:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster0 Link encap:UNSPEC Hardware Adresse 00-90-4B-97-34-73-6C-6F-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 Kollisionen:0 Sendewarteschlangenl=E4nge:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) shows this, lo no wireless extensions. eth0 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11b ESSID:"" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=3D27 dBm Retry min limit:7 RTS thr:off Fragment thr=3D2352 B Encryption key:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I am not sure whether this Card is active, because show me, [ 409.752921] b43legacy-phy0: Radio hardware status changed to DISABLE= D Another funny Thing is, that i can execute and=20 get a Result, wlan0 Scan completed : Cell 01 - Address: 02:00:7C:81:E1:73 ESSID:"kleopatra" Mode:Ad-Hoc Channel:10 Frequency:2.457 GHz (Channel 10) Quality=3D55/100 Signal level=3D-55 dBm Noise=20 level=3D-43 dBm Encryption key:on Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s Extra:tsf=3D0000000075bb2b8d The Adress seems to change sometimes ??? I don't know why. Regards Markus -- To unsubscribe from this list: send the line "unsubscribe linux-wireles= s" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html