Return-path: Received: from main.gmane.org ([80.91.229.2]:48695 "EHLO ciao.gmane.org" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1757952AbZACSgg (ORCPT ); Sat, 3 Jan 2009 13:36:36 -0500 Received: from list by ciao.gmane.org with local (Exim 4.43) id 1LJBMM-00046Y-Iv for linux-wireless@vger.kernel.org; Sat, 03 Jan 2009 18:36:30 +0000 Received: from 77.21.169.220 ([77.21.169.220]) by main.gmane.org with esmtp (Gmexim 0.1 (Debian)) id 1AlnuQ-0007hv-00 for ; Sat, 03 Jan 2009 18:36:30 +0000 Received: from feldmann_markus by 77.21.169.220 with local (Gmexim 0.1 (Debian)) id 1AlnuQ-0007hv-00 for ; Sat, 03 Jan 2009 18:36:30 +0000 To: linux-wireless@vger.kernel.org From: feldmaus Subject: Re: Do not get BCM4303 to work Date: Sat, 03 Jan 2009 19:37:46 +0100 Message-ID: (sfid-20090103_193640_265863_431A4321) References: Mime-Version: 1.0 Content-Type: text/plain; charset=ISO-8859-15; format=flowed In-Reply-To: Sender: linux-wireless-owner@vger.kernel.org List-ID: Hi All, My actually Sydtem is: HP Pavilion Laptop zv5000 Debian Lenny(Testing) Linux Kernel 2.6.28 from kernel.org Broadcom Wlan card BCM4303 My System doesnt work at all. My Boot Messages are: [ 21.331095] b43legacy-phy0: Broadcom 4301 WLAN found [ 21.412214] b43legacy-phy0 debug: Found PHY: Analog 0, Type 1, Revision 4 [ 21.412240] b43legacy-phy0 debug: Found Radio: Manuf 0x17F, Version 0x2050, Revision 2 [ 21.436305] b43legacy-phy0 debug: Radio initialized [ 40.529192] input: b43legacy-phy0 as /class/input/input9 [ 40.632070] b43legacy ssb0:0: firmware: requesting b43legacy/ucode2.fw [ 40.696281] b43legacy ssb0:0: firmware: requesting b43legacy/pcm4.fw [ 40.757265] b43legacy ssb0:0: firmware: requesting b43legacy/b0g0initvals2.fw [ 40.984045] b43legacy-phy0: Loading firmware version 0x127, patch level 14 (2005-04-18 02:36:27) [ 41.100298] b43legacy-phy0 debug: Chip initialized [ 41.100599] b43legacy-phy0 debug: 30-bit DMA initialized [ 41.100748] Registered led device: b43legacy-phy0:tx [ 41.109182] Registered led device: b43legacy-phy0:rx [ 41.117508] Registered led device: b43legacy-phy0:radio [ 41.125678] b43legacy-phy0 debug: Wireless interface started [ 41.125685] b43legacy-phy0 debug: Adding Interface type 2 [ 41.584048] b43legacy-phy0: Radio hardware status changed to DISABLED [ 41.593709] b43legacy-phy0 debug: Radio initialized [ 41.924035] b43legacy-phy0: Radio turned on by software [ 41.932354] b43legacy-phy0: The hardware RF-kill button still turns the radio physically off. Press the button to turn it on. Actually i am looking whether i missing some Kernel Options. As we can see in the Boot Messages i have to activate the RF-kill Button by pressing, but this does not activate my wlan. Any Ideas? Regards Markus