Return-path: Received: from venema.h4ckr.net ([217.24.1.135]:56443 "EHLO venema.h4ckr.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752041AbZAaCbx (ORCPT ); Fri, 30 Jan 2009 21:31:53 -0500 Date: Sat, 31 Jan 2009 04:31:47 +0200 From: Nick Kossifidis To: ath5k-devel@lists.ath5k.org, linux-wireless@vger.kernel.org Cc: linville@tuxdriver.com, jirislaby@gmail.com, mcgrof@gmail.com, me@bobcopeland.com, nbd@openwrt.org Subject: [PATCH 5/5] ath5k: Update reset code Message-ID: <20090131023147.GE3342@makis> (sfid-20090131_033158_457462_00DEACCD) MIME-Version: 1.0 Content-Type: text/plain; charset=us-ascii Sender: linux-wireless-owner@vger.kernel.org List-ID: * Update reset and sync with HALs * Clean up eeprom settings and tweaking of initvals and put them on separate functions * Set/Restore 32KHz ref clk operation * Add some more documentation TODO: Spur mitigation, tpc, half/quarter rate, compression etc Signed-Off-by: Nick Kossifidis --- drivers/net/wireless/ath5k/ath5k.h | 12 +- drivers/net/wireless/ath5k/attach.c | 16 +- drivers/net/wireless/ath5k/eeprom.c | 12 + drivers/net/wireless/ath5k/eeprom.h | 1 + drivers/net/wireless/ath5k/reg.h | 41 +- drivers/net/wireless/ath5k/reset.c | 901 ++++++++++++++++++++++++++--------- 6 files changed, 711 insertions(+), 272 deletions(-) diff --git a/drivers/net/wireless/ath5k/ath5k.h b/drivers/net/wireless/ath5k/ath5k.h index 5b2e0da..a3313be 100644 --- a/drivers/net/wireless/ath5k/ath5k.h +++ b/drivers/net/wireless/ath5k/ath5k.h @@ -222,6 +222,8 @@ #endif /* Initial values */ +#define AR5K_INIT_RSSI_THR 0x00000781 +#define AR5K_INIT_CYCRSSI_THR1 2 #define AR5K_INIT_TX_LATENCY 502 #define AR5K_INIT_USEC 39 #define AR5K_INIT_USEC_TURBO 79 @@ -313,7 +315,7 @@ struct ath5k_srev_name { #define AR5K_SREV_AR5424 0x90 /* Condor */ #define AR5K_SREV_AR5413 0xa4 /* Eagle lite */ #define AR5K_SREV_AR5414 0xa0 /* Eagle */ -#define AR5K_SREV_AR2415 0xb0 /* Cobra */ +#define AR5K_SREV_AR2415 0xb0 /* Talon */ #define AR5K_SREV_AR5416 0xc0 /* PCI-E */ #define AR5K_SREV_AR5418 0xca /* PCI-E */ #define AR5K_SREV_AR2425 0xe0 /* Swan */ @@ -331,7 +333,7 @@ struct ath5k_srev_name { #define AR5K_SREV_RAD_2112B 0x46 #define AR5K_SREV_RAD_2413 0x50 #define AR5K_SREV_RAD_5413 0x60 -#define AR5K_SREV_RAD_2316 0x70 +#define AR5K_SREV_RAD_2316 0x70 /* Cobra SoC */ #define AR5K_SREV_RAD_2317 0x80 #define AR5K_SREV_RAD_5424 0xa0 /* Mostly same as 5413 */ #define AR5K_SREV_RAD_2425 0xa2 @@ -340,7 +342,7 @@ struct ath5k_srev_name { #define AR5K_SREV_PHY_5211 0x30 #define AR5K_SREV_PHY_5212 0x41 #define AR5K_SREV_PHY_5212A 0x42 -#define AR5K_SREV_PHY_2112B 0x43 +#define AR5K_SREV_PHY_5212B 0x43 #define AR5K_SREV_PHY_2413 0x45 #define AR5K_SREV_PHY_5413 0x61 #define AR5K_SREV_PHY_2425 0x70 @@ -1030,7 +1032,6 @@ struct ath5k_hw { u16 ah_phy_revision; u16 ah_radio_5ghz_revision; u16 ah_radio_2ghz_revision; - u32 ah_phy_spending; enum ath5k_version ah_version; enum ath5k_radio ah_radio; @@ -1156,6 +1157,7 @@ extern void ath5k_hw_update_mib_counters(struct ath5k_hw *ah, struct ieee80211_l /* EEPROM access functions */ extern int ath5k_eeprom_init(struct ath5k_hw *ah); extern int ath5k_eeprom_read_mac(struct ath5k_hw *ah, u8 *mac); +extern bool ath5k_eeprom_is_hb63(struct ath5k_hw *ah); /* Protocol Control Unit Functions */ extern int ath5k_hw_set_opmode(struct ath5k_hw *ah); @@ -1258,6 +1260,7 @@ extern int ath5k_hw_set_txpower_limit(struct ath5k_hw *ah, unsigned int power); /* * Translate usec to hw clock units + * TODO: Half/quarter rate */ static inline unsigned int ath5k_hw_htoclock(unsigned int usec, bool turbo) { @@ -1266,6 +1269,7 @@ static inline unsigned int ath5k_hw_htoclock(unsigned int usec, bool turbo) /* * Translate hw clock units to usec + * TODO: Half/quarter rate */ static inline unsigned int ath5k_hw_clocktoh(unsigned int clock, bool turbo) { diff --git a/drivers/net/wireless/ath5k/attach.c b/drivers/net/wireless/ath5k/attach.c index a3f07a4..05bc5cb 100644 --- a/drivers/net/wireless/ath5k/attach.c +++ b/drivers/net/wireless/ath5k/attach.c @@ -169,7 +169,6 @@ struct ath5k_hw *ath5k_hw_attach(struct ath5k_softc *sc, u8 mac_version) ah->ah_single_chip = false; ah->ah_radio_2ghz_revision = ath5k_hw_radio_revision(ah, CHANNEL_2GHZ); - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5111; break; case AR5K_SREV_RAD_5112: case AR5K_SREV_RAD_2112: @@ -177,38 +176,31 @@ struct ath5k_hw *ath5k_hw_attach(struct ath5k_softc *sc, u8 mac_version) ah->ah_single_chip = false; ah->ah_radio_2ghz_revision = ath5k_hw_radio_revision(ah, CHANNEL_2GHZ); - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5112; break; case AR5K_SREV_RAD_2413: ah->ah_radio = AR5K_RF2413; ah->ah_single_chip = true; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2413; break; case AR5K_SREV_RAD_5413: ah->ah_radio = AR5K_RF5413; ah->ah_single_chip = true; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5413; break; case AR5K_SREV_RAD_2316: ah->ah_radio = AR5K_RF2316; ah->ah_single_chip = true; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2316; break; case AR5K_SREV_RAD_2317: ah->ah_radio = AR5K_RF2317; ah->ah_single_chip = true; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2317; break; case AR5K_SREV_RAD_5424: if (ah->ah_mac_version == AR5K_SREV_AR2425 || ah->ah_mac_version == AR5K_SREV_AR2417){ ah->ah_radio = AR5K_RF2425; ah->ah_single_chip = true; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2425; } else { ah->ah_radio = AR5K_RF5413; ah->ah_single_chip = true; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5413; } break; default: @@ -227,29 +219,25 @@ struct ath5k_hw *ath5k_hw_attach(struct ath5k_softc *sc, u8 mac_version) ah->ah_radio = AR5K_RF2425; ah->ah_single_chip = true; ah->ah_radio_5ghz_revision = AR5K_SREV_RAD_2425; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2425; } else if (srev == AR5K_SREV_AR5213A && - ah->ah_phy_revision == AR5K_SREV_PHY_2112B) { + ah->ah_phy_revision == AR5K_SREV_PHY_5212B) { ah->ah_radio = AR5K_RF5112; ah->ah_single_chip = false; - ah->ah_radio_5ghz_revision = AR5K_SREV_RAD_2112B; + ah->ah_radio_5ghz_revision = AR5K_SREV_RAD_5112B; } else if (ah->ah_mac_version == (AR5K_SREV_AR2415 >> 4)) { ah->ah_radio = AR5K_RF2316; ah->ah_single_chip = true; ah->ah_radio_5ghz_revision = AR5K_SREV_RAD_2316; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2316; } else if (ah->ah_mac_version == (AR5K_SREV_AR5414 >> 4) || ah->ah_phy_revision == AR5K_SREV_PHY_5413) { ah->ah_radio = AR5K_RF5413; ah->ah_single_chip = true; ah->ah_radio_5ghz_revision = AR5K_SREV_RAD_5413; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF5413; } else if (ah->ah_mac_version == (AR5K_SREV_AR2414 >> 4) || ah->ah_phy_revision == AR5K_SREV_PHY_2413) { ah->ah_radio = AR5K_RF2413; ah->ah_single_chip = true; ah->ah_radio_5ghz_revision = AR5K_SREV_RAD_2413; - ah->ah_phy_spending = AR5K_PHY_SPENDING_RF2413; } else { ATH5K_ERR(sc, "Couldn't identify radio revision.\n"); ret = -ENODEV; diff --git a/drivers/net/wireless/ath5k/eeprom.c b/drivers/net/wireless/ath5k/eeprom.c index b4ec539..5f16fea 100644 --- a/drivers/net/wireless/ath5k/eeprom.c +++ b/drivers/net/wireless/ath5k/eeprom.c @@ -1412,6 +1412,7 @@ ath5k_eeprom_init(struct ath5k_hw *ah) return 0; } + /* * Read the MAC address from eeprom */ @@ -1448,3 +1449,14 @@ int ath5k_eeprom_read_mac(struct ath5k_hw *ah, u8 *mac) return 0; } +bool ath5k_eeprom_is_hb63(struct ath5k_hw *ah) +{ + u16 data; + + ath5k_hw_eeprom_read(ah, AR5K_EEPROM_IS_HB63, &data); + + if ((ah->ah_mac_version == (AR5K_SREV_AR2425 >> 4) && data)) + return true; + else + return false; +} diff --git a/drivers/net/wireless/ath5k/eeprom.h b/drivers/net/wireless/ath5k/eeprom.h index 09eb7d0..1deebc0 100644 --- a/drivers/net/wireless/ath5k/eeprom.h +++ b/drivers/net/wireless/ath5k/eeprom.h @@ -25,6 +25,7 @@ #define AR5K_EEPROM_MAGIC_5211 0x0000145b /* 5211 */ #define AR5K_EEPROM_MAGIC_5210 0x0000145a /* 5210 */ +#define AR5K_EEPROM_IS_HB63 0x000b /* Talon detect */ #define AR5K_EEPROM_REG_DOMAIN 0x00bf /* EEPROM regdom */ #define AR5K_EEPROM_CHECKSUM 0x00c0 /* EEPROM checksum */ #define AR5K_EEPROM_INFO_BASE 0x00c0 /* EEPROM header */ diff --git a/drivers/net/wireless/ath5k/reg.h b/drivers/net/wireless/ath5k/reg.h index 84f4669..d023eb5 100644 --- a/drivers/net/wireless/ath5k/reg.h +++ b/drivers/net/wireless/ath5k/reg.h @@ -187,6 +187,7 @@ #define AR5K_TXCFG_FRMPAD_DIS 0x00002000 /* [5211+] */ #define AR5K_TXCFG_RDY_CBR_DIS 0x00004000 /* Ready time CBR disable [5211+] */ #define AR5K_TXCFG_JUMBO_FRM_MODE 0x00008000 /* Jumbo frame mode [5211+] */ +#define AR5K_TXCFG_DCU_DBL_BUF_DIS 0x00008000 /* Disable doulbe buffering on DCU */ #define AR5K_TXCFG_DCU_CACHING_DIS 0x00010000 /* Disable DCU caching */ /* @@ -753,7 +754,7 @@ */ #define AR5K_DCU_SEQNUM_BASE 0x1140 #define AR5K_DCU_SEQNUM_M 0x00000fff -#define AR5K_QUEUE_DFS_SEQNUM(_q) AR5K_QUEUE_REG(AR5K_DCU_SEQNUM_BASE, _q) +#define AR5K_QUEUE_DCU_SEQNUM(_q) AR5K_QUEUE_REG(AR5K_DCU_SEQNUM_BASE, _q) /* * DCU global IFS SIFS register @@ -1679,7 +1680,7 @@ * TSF parameter register */ #define AR5K_TSF_PARM 0x8104 /* Register Address */ -#define AR5K_TSF_PARM_INC_M 0x000000ff /* Mask for TSF increment */ +#define AR5K_TSF_PARM_INC 0x000000ff /* Mask for TSF increment */ #define AR5K_TSF_PARM_INC_S 0 /* @@ -1928,8 +1929,8 @@ #define AR5K_PHY_RF_CTL2_TXF2TXD_START_S 0 #define AR5K_PHY_RF_CTL3 0x9828 /* Register Address */ -#define AR5K_PHY_RF_CTL3_TXE2XLNA_ON 0x0000000f /* TX end to XLNA on */ -#define AR5K_PHY_RF_CTL3_TXE2XLNA_ON_S 0 +#define AR5K_PHY_RF_CTL3_TXE2XLNA_ON 0x0000ff00 /* TX end to XLNA on */ +#define AR5K_PHY_RF_CTL3_TXE2XLNA_ON_S 8 #define AR5K_PHY_ADC_CTL 0x982c #define AR5K_PHY_ADC_CTL_INBUFGAIN_OFF 0x00000003 @@ -1963,7 +1964,7 @@ #define AR5K_PHY_SETTLING_AGC 0x0000007f /* AGC settling time */ #define AR5K_PHY_SETTLING_AGC_S 0 #define AR5K_PHY_SETTLING_SWITCH 0x00003f80 /* Switch settlig time */ -#define AR5K_PHY_SETTLINK_SWITCH_S 7 +#define AR5K_PHY_SETTLING_SWITCH_S 7 /* * PHY Gain registers @@ -2069,14 +2070,14 @@ * PHY sleep registers [5112+] */ #define AR5K_PHY_SCR 0x9870 -#define AR5K_PHY_SCR_32MHZ 0x0000001f #define AR5K_PHY_SLMT 0x9874 #define AR5K_PHY_SLMT_32MHZ 0x0000007f #define AR5K_PHY_SCAL 0x9878 #define AR5K_PHY_SCAL_32MHZ 0x0000000e - +#define AR5K_PHY_SCAL_32MHZ_2417 0x0000000a +#define AR5K_PHY_SCAL_32MHZ_HB63 0x00000032 /* * PHY PLL (Phase Locked Loop) control register @@ -2156,7 +2157,8 @@ #define AR5K_PHY_ANT_CTL_TXRX_EN 0x00000001 /* Enable TX/RX (?) */ #define AR5K_PHY_ANT_CTL_SECTORED_ANT 0x00000004 /* Sectored Antenna */ #define AR5K_PHY_ANT_CTL_HITUNE5 0x00000008 /* Hitune5 (?) */ -#define AR5K_PHY_ANT_CTL_SWTABLE_IDLE 0x00000010 /* Switch table idle (?) */ +#define AR5K_PHY_ANT_CTL_SWTABLE_IDLE 0x000003f9 /* Switch table idle (?) */ +#define AR5K_PHY_ANT_CTL_SWTABLE_IDLE_S 4 /* * PHY receiver delay register [5111+] @@ -2196,7 +2198,7 @@ #define AR5K_PHY_OFDM_SELFCORR 0x9924 /* Register Address */ #define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1_EN 0x00000001 /* Enable cyclic RSSI thr 1 */ #define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1 0x000000fe /* Mask for Cyclic RSSI threshold 1 */ -#define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1_S 0 +#define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1_S 1 #define AR5K_PHY_OFDM_SELFCORR_CYPWR_THR3 0x00000100 /* Cyclic RSSI threshold 3 (field) (?) */ #define AR5K_PHY_OFDM_SELFCORR_RSSI_1ATHR_EN 0x00008000 /* Enable 1A RSSI threshold (?) */ #define AR5K_PHY_OFDM_SELFCORR_RSSI_1ATHR 0x00010000 /* 1A RSSI threshold (field) (?) */ @@ -2279,6 +2281,15 @@ AR5K_PHY_FRAME_CTL_TIMING_ERR /* + * PHY Tx Power adjustment register [5212A+] + */ +#define AR5K_PHY_TX_PWR_ADJ 0x994c +#define AR5K_PHY_TX_PWR_ADJ_CCK_GAIN_DELTA 0x00000fc0 +#define AR5K_PHY_TX_PWR_ADJ_CCK_GAIN_DELTA_S 6 +#define AR5K_PHY_TX_PWR_ADJ_CCK_PCDAC_INDEX 0x00fc0000 +#define AR5K_PHY_TX_PWR_ADJ_CCK_PCDAC_INDEX_S 18 + +/* * PHY radar detection register [5111+] */ #define AR5K_PHY_RADAR 0x9954 @@ -2459,17 +2470,7 @@ #define AR5K_PHY_SDELAY 0x99f4 #define AR5K_PHY_SDELAY_32MHZ 0x000000ff #define AR5K_PHY_SPENDING 0x99f8 -#define AR5K_PHY_SPENDING_14 0x00000014 -#define AR5K_PHY_SPENDING_18 0x00000018 -#define AR5K_PHY_SPENDING_RF5111 0x00000018 -#define AR5K_PHY_SPENDING_RF5112 0x00000014 -/* #define AR5K_PHY_SPENDING_RF5112A 0x0000000e */ -/* #define AR5K_PHY_SPENDING_RF5424 0x00000012 */ -#define AR5K_PHY_SPENDING_RF5413 0x00000018 -#define AR5K_PHY_SPENDING_RF2413 0x00000018 -#define AR5K_PHY_SPENDING_RF2316 0x00000018 -#define AR5K_PHY_SPENDING_RF2317 0x00000018 -#define AR5K_PHY_SPENDING_RF2425 0x00000014 + /* * PHY PAPD I (power?) table (?) diff --git a/drivers/net/wireless/ath5k/reset.c b/drivers/net/wireless/ath5k/reset.c index 579c64c..34dc2d5 100644 --- a/drivers/net/wireless/ath5k/reset.c +++ b/drivers/net/wireless/ath5k/reset.c @@ -37,10 +37,14 @@ * @ah: the &struct ath5k_hw * @channel: the currently set channel upon reset * - * Write the OFDM timings for the AR5212 upon reset. This is a helper for - * ath5k_hw_reset(). This seems to tune the PLL a specified frequency - * depending on the bandwidth of the channel. + * Write the delta slope coefficient (used on pilot tracking ?) for OFDM + * operration on the AR5212 upon reset. This is a helper for ath5k_hw_reset(). * + * Since delta slope is floating point we split it on it's exponent and + * mantissa and provide these values on hw. + * + * For more infos i think this pattent is related + * http://www.freepatentsonline.com/7184495.html */ static inline int ath5k_hw_write_ofdm_timings(struct ath5k_hw *ah, struct ieee80211_channel *channel) @@ -53,13 +57,20 @@ static inline int ath5k_hw_write_ofdm_timings(struct ath5k_hw *ah, !(channel->hw_value & CHANNEL_OFDM)) BUG(); - /* Seems there are two PLLs, one for baseband sampling and one - * for tuning. Tuning basebands are 40 MHz or 80MHz when in - * turbo. */ - clock = channel->hw_value & CHANNEL_TURBO ? 80 : 40; + /* Get coefficient + * ALGO: coef = (5 * clock * carrier_freq) / 2) + * we scale coef by shifting clock value by 24 for + * better precision since we use integers */ + /* TODO: Half/quarter rate */ + clock = channel->hw_value & CHANNEL_TURBO ? + ath5k_hw_htoclock(1, true) : + ath5k_hw_htoclock(1, false); + coef_scaled = ((5 * (clock << 24)) / 2) / channel->center_freq; + /* Get exponent + * ALGO: coe_exp = 14 - highest set bit position */ for (coef_exp = 31; coef_exp > 0; coef_exp--) if ((coef_scaled >> coef_exp) & 0x1) break; @@ -68,8 +79,14 @@ static inline int ath5k_hw_write_ofdm_timings(struct ath5k_hw *ah, return -EINVAL; coef_exp = 14 - (coef_exp - 24); + + /* Get mantissa (significant digits) + * ALGO: coef_mant = floor(coef_scaled* 2^coef_exp+0.5) */ coef_man = coef_scaled + (1 << (24 - coef_exp - 1)); + + /* Calculate delta slope coefficient exponent + * and mantissa (remove scaling) and set them on hw */ ds_coef_man = coef_man >> (24 - coef_exp); ds_coef_exp = coef_exp - 16; @@ -90,16 +107,22 @@ static int control_rates[] = { 0, 1, 1, 1, 4, 4, 6, 6, 8, 8, 8, 8 }; /** - * ath5k_hw_write_rate_duration - set rate duration during hw resets + * ath5k_hw_write_rate_duration - set rate code to duration table during hw resets * * @ah: the &struct ath5k_hw * @mode: one of enum ath5k_driver_mode * - * Write the rate duration table upon hw reset. This is a helper for - * ath5k_hw_reset(). It seems all this is doing is setting an ACK timeout for - * the hardware for the current mode for each rate. The rates which are capable - * of short preamble (802.11b rates 2Mbps, 5.5Mbps, and 11Mbps) have another - * register for the short preamble ACK timeout calculation. + * Write the rate code to duration table upon hw reset. This is a helper for + * ath5k_hw_reset(). It seems all this is doing is setting an ACK timeout on + * the hardware, based on current mode, for each rate. The rates which are capable + * of short preamble (802.11b rates 2Mbps, 5.5Mbps, and 11Mbps) have different + * rate code so we write their value twice (one for long preample and one for short). + * + * Note: Band doesn't matter here, if we set the values for OFDM it works + * on both a and g modes. So all we have to do is set values for all g rates + * that include all OFDM and CCK rates. If we operate in turbo or xr/half/quarter + * rate mode, we need to use another set of bitrates (that's why we need the mode + * parameter) but we don't handle these proprietary modes yet. */ static inline void ath5k_hw_write_rate_duration(struct ath5k_hw *ah, unsigned int mode) @@ -275,7 +298,8 @@ commit: } /* - * Bring up MAC + PHY Chips + * Bring up MAC + PHY Chips and program PLL + * TODO: Half/Quarter rate support */ int ath5k_hw_nic_wakeup(struct ath5k_hw *ah, int flags, bool initial) { @@ -333,7 +357,11 @@ int ath5k_hw_nic_wakeup(struct ath5k_hw *ah, int flags, bool initial) } } else if (flags & CHANNEL_5GHZ) { mode |= AR5K_PHY_MODE_FREQ_5GHZ; - clock |= AR5K_PHY_PLL_40MHZ; + + if (ah->ah_radio == AR5K_RF5413) + clock |= AR5K_PHY_PLL_40MHZ_5413; + else + clock |= AR5K_PHY_PLL_40MHZ; if (flags & CHANNEL_OFDM) mode |= AR5K_PHY_MODE_MOD_OFDM; @@ -391,10 +419,14 @@ int ath5k_hw_nic_wakeup(struct ath5k_hw *ah, int flags, bool initial) } if (ah->ah_version != AR5K_AR5210) { - /* ...set the PHY operating mode */ - ath5k_hw_reg_write(ah, clock, AR5K_PHY_PLL); - udelay(300); + /* ...program PLL if it needs change */ + if (ath5k_hw_reg_read(ah, AR5K_PHY_PLL) != clock) { + ath5k_hw_reg_write(ah, clock, AR5K_PHY_PLL); + udelay(300); + } + + /* ...set the PHY operating mode */ ath5k_hw_reg_write(ah, mode, AR5K_PHY_MODE); ath5k_hw_reg_write(ah, turbo, AR5K_PHY_TURBO); } @@ -403,22 +435,397 @@ int ath5k_hw_nic_wakeup(struct ath5k_hw *ah, int flags, bool initial) } /* + * If there is an external 32KHz crystal available, use it + * as ref. clock instead of 32/40MHz clock and baseband clocks + * to save power durring sleep or restore normal 32/40MHz + * operation. + * + * XXX: When operating on 32KHz certain PHY registers (27 - 31, + * 123 - 127) require delay on access. + */ +void ath5k_hw_set_sleep_clock(struct ath5k_hw *ah, bool enable) +{ + struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; + u32 scal, spending, usec32; + + /* No 32KHz clock available, stick to the default + * settings we got from initvals */ + if (!(AR5K_EEPROM_HAS32KHZCRYSTAL(ee->ee_misc1) || + AR5K_EEPROM_HAS32KHZCRYSTAL_OLD(ee->ee_misc1))) + return; + + if (enable) { + + /* 1 usec/cycle */ + AR5K_REG_WRITE_BITS(ah, AR5K_USEC_5211, AR5K_USEC_32, 1); + /* Set up tsf increment on each cycle */ + AR5K_REG_WRITE_BITS(ah, AR5K_TSF_PARM, AR5K_TSF_PARM_INC, 61); + + /* Set baseband sleep control registers + * and sleep control rate */ + ath5k_hw_reg_write(ah, 0x1f, AR5K_PHY_SCR); + + if ((ah->ah_radio == AR5K_RF5112) || + (ah->ah_radio == AR5K_RF5413) || + (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4))) + spending = 0x14; + else + spending = 0x18; + ath5k_hw_reg_write(ah, spending, AR5K_PHY_SPENDING); + + if ((ah->ah_radio == AR5K_RF5112) || + (ah->ah_radio == AR5K_RF5413) || + (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4))) { + ath5k_hw_reg_write(ah, 0x26, AR5K_PHY_SLMT); + ath5k_hw_reg_write(ah, 0x0d, AR5K_PHY_SCAL); + ath5k_hw_reg_write(ah, 0x07, AR5K_PHY_SCLOCK); + ath5k_hw_reg_write(ah, 0x3f, AR5K_PHY_SDELAY); + AR5K_REG_WRITE_BITS(ah, AR5K_PCICFG, + AR5K_PCICFG_SLEEP_CLOCK_RATE, 0x02); + } else { + ath5k_hw_reg_write(ah, 0x0a, AR5K_PHY_SLMT); + ath5k_hw_reg_write(ah, 0x0c, AR5K_PHY_SCAL); + ath5k_hw_reg_write(ah, 0x03, AR5K_PHY_SCLOCK); + ath5k_hw_reg_write(ah, 0x20, AR5K_PHY_SDELAY); + AR5K_REG_WRITE_BITS(ah, AR5K_PCICFG, + AR5K_PCICFG_SLEEP_CLOCK_RATE, 0x03); + } + + /* Enable sleep clock operation */ + AR5K_REG_ENABLE_BITS(ah, AR5K_PCICFG, + AR5K_PCICFG_SLEEP_CLOCK_EN); + + } else { + + /* Disable sleep clock operation and + * restore default parameters */ + AR5K_REG_DISABLE_BITS(ah, AR5K_PCICFG, + AR5K_PCICFG_SLEEP_CLOCK_EN); + + AR5K_REG_WRITE_BITS(ah, AR5K_PCICFG, + AR5K_PCICFG_SLEEP_CLOCK_RATE, 0); + + ath5k_hw_reg_write(ah, 0x1f, AR5K_PHY_SCR); + ath5k_hw_reg_write(ah, AR5K_PHY_SLMT_32MHZ, AR5K_PHY_SLMT); + + if (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4)) + scal = AR5K_PHY_SCAL_32MHZ_2417; + else if (ath5k_eeprom_is_hb63(ah)) + scal = AR5K_PHY_SCAL_32MHZ_HB63; + else + scal = AR5K_PHY_SCAL_32MHZ; + ath5k_hw_reg_write(ah, scal, AR5K_PHY_SCAL); + + ath5k_hw_reg_write(ah, AR5K_PHY_SCLOCK_32MHZ, AR5K_PHY_SCLOCK); + ath5k_hw_reg_write(ah, AR5K_PHY_SDELAY_32MHZ, AR5K_PHY_SDELAY); + + if ((ah->ah_radio == AR5K_RF5112) || + (ah->ah_radio == AR5K_RF5413) || + (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4))) + spending = 0x14; + else + spending = 0x18; + ath5k_hw_reg_write(ah, spending, AR5K_PHY_SPENDING); + + if ((ah->ah_radio == AR5K_RF5112) || + (ah->ah_radio == AR5K_RF5413)) + usec32 = 39; + else + usec32 = 31; + AR5K_REG_WRITE_BITS(ah, AR5K_USEC_5211, AR5K_USEC_32, usec32); + + AR5K_REG_WRITE_BITS(ah, AR5K_TSF_PARM, AR5K_TSF_PARM_INC, 1); + } + return; +} + +static bool ath5k_hw_chan_has_spur_noise(struct ath5k_hw *ah, + struct ieee80211_channel *channel) +{ + u8 refclk_freq; + + if ((ah->ah_radio == AR5K_RF5112) || + (ah->ah_radio == AR5K_RF5413) || + (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4))) + refclk_freq = 40; + else + refclk_freq = 32; + + if ((channel->center_freq % refclk_freq != 0) && + ((channel->center_freq % refclk_freq < 10) || + (channel->center_freq % refclk_freq > 22))) + return true; + else + return false; +} + +/* TODO: Half/Quarter rate */ +static void ath5k_hw_tweak_initval_settings(struct ath5k_hw *ah, + struct ieee80211_channel *channel) +{ + u32 data; + + if (ah->ah_version == AR5K_AR5212 && + ah->ah_phy_revision > AR5K_SREV_PHY_5212A) { + + /* Setup ADC control */ + ath5k_hw_reg_write(ah, + (AR5K_REG_SM(2, + AR5K_PHY_ADC_CTL_INBUFGAIN_OFF) | + AR5K_REG_SM(2, + AR5K_PHY_ADC_CTL_INBUFGAIN_ON) | + AR5K_PHY_ADC_CTL_PWD_DAC_OFF | + AR5K_PHY_ADC_CTL_PWD_ADC_OFF), + AR5K_PHY_ADC_CTL); + + + + /* Disable barker RSSI threshold */ + AR5K_REG_DISABLE_BITS(ah, AR5K_PHY_DAG_CCK_CTL, + AR5K_PHY_DAG_CCK_CTL_EN_RSSI_THR); + + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_DAG_CCK_CTL, + AR5K_PHY_DAG_CCK_CTL_RSSI_THR, 2); + + /* Set the mute mask */ + ath5k_hw_reg_write(ah, 0x0000000f, AR5K_SEQ_MASK); + } + + /* Clear PHY_BLUETOOTH to allow RX_CLEAR line debug */ + if (ah->ah_phy_revision >= AR5K_SREV_PHY_5212B) + ath5k_hw_reg_write(ah, 0, AR5K_PHY_BLUETOOTH); + + /* Enable DCU double buffering */ + if (ah->ah_phy_revision > AR5K_SREV_PHY_5212B) + AR5K_REG_DISABLE_BITS(ah, AR5K_TXCFG, + AR5K_TXCFG_DCU_DBL_BUF_DIS); + + /* Set DAC/ADC delays */ + if (ah->ah_version == AR5K_AR5212) { + if (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4)) + data = AR5K_PHY_SCAL_32MHZ_2417; + else if (ath5k_eeprom_is_hb63(ah)) + data = AR5K_PHY_SCAL_32MHZ_HB63; + else + data = AR5K_PHY_SCAL_32MHZ; + ath5k_hw_reg_write(ah, data, AR5K_PHY_SCAL); + data = 0; + } + + /* Set fast ADC */ + if ((ah->ah_radio == AR5K_RF5413) || + (ah->ah_mac_version == (AR5K_SREV_AR2417 >> 4))) { + data = 1; + + if (channel->center_freq == 2462 || + channel->center_freq == 2467) + data = 0; + + if (ath5k_hw_reg_read(ah, AR5K_PHY_FAST_ADC) != data) + ath5k_hw_reg_write(ah, data, + AR5K_PHY_FAST_ADC); + data = 0; + } + + /* Fix for first revision of the RF5112 RF chipset */ + if (ah->ah_radio >= AR5K_RF5112 && + ah->ah_radio_5ghz_revision < + AR5K_SREV_RAD_5112A) { + ath5k_hw_reg_write(ah, AR5K_PHY_CCKTXCTL_WORLD, + AR5K_PHY_CCKTXCTL); + if (channel->hw_value & CHANNEL_5GHZ) + data = 0xffb81020; + else + data = 0xffb80d20; + ath5k_hw_reg_write(ah, data, AR5K_PHY_FRAME_CTL); + data = 0; + } + + if (ah->ah_mac_srev < AR5K_SREV_AR5211) { + /* 5311 has different tx/rx latency masks + * from 5211, since we deal 5311 the same + * as 5211 when setting initvals, shift + * values here to their proper locations */ + data = ath5k_hw_reg_read(ah, AR5K_USEC_5211); + ath5k_hw_reg_write(ah, data & (AR5K_USEC_1 | + AR5K_USEC_32 | + AR5K_USEC_TX_LATENCY_5211 | + AR5K_REG_SM(29, + AR5K_USEC_RX_LATENCY_5210)), + AR5K_USEC_5211); + /* Clear QCU/DCU clock gating register */ + ath5k_hw_reg_write(ah, 0, AR5K_QCUDCU_CLKGT); + /* Set DAC/ADC delays */ + ath5k_hw_reg_write(ah, 0x08, AR5K_PHY_SCAL); + /* Enable PCU FIFO corruption ECO */ + AR5K_REG_ENABLE_BITS(ah, AR5K_DIAG_SW_5211, + AR5K_DIAG_SW_ECO_ENABLE); + data = 0; + } + + return; +} + +static void ath5k_hw_commit_eeprom_settings(struct ath5k_hw *ah, + struct ieee80211_channel *channel, u8 *ant, u8 ee_mode) +{ + struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; + int16_t cck_ofdm_pwr_delta = 0; + + /* Set CCK to OFDM power delta */ + if (ah->ah_phy_revision > AR5K_SREV_PHY_5212A) { + /* Adjust power delta for channel 14 */ + if (channel->center_freq == 2484) + cck_ofdm_pwr_delta = + ((ee->ee_cck_ofdm_power_delta - + ee->ee_scaled_cck_delta) * 2) / 10; + else + cck_ofdm_pwr_delta = + ee->ee_cck_ofdm_power_delta; + + if (channel->hw_value == CHANNEL_G) + ath5k_hw_reg_write(ah, + AR5K_REG_SM((ee->ee_cck_ofdm_power_delta * -1), + AR5K_PHY_TX_PWR_ADJ_CCK_GAIN_DELTA) | + AR5K_REG_SM((cck_ofdm_pwr_delta * -1), + AR5K_PHY_TX_PWR_ADJ_CCK_PCDAC_INDEX), + AR5K_PHY_TX_PWR_ADJ); + else + ath5k_hw_reg_write(ah, 0, AR5K_PHY_TX_PWR_ADJ); + } + + /* Set antenna idle switch table */ + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_ANT_CTL, + AR5K_PHY_ANT_CTL_SWTABLE_IDLE, + ah->ah_antenna[ee_mode][0]); + + /* Set antenna switch table */ + ath5k_hw_reg_write(ah, ah->ah_antenna[ee_mode][ant[0]], + AR5K_PHY_ANT_SWITCH_TABLE_0); + ath5k_hw_reg_write(ah, ah->ah_antenna[ee_mode][ant[1]], + AR5K_PHY_ANT_SWITCH_TABLE_1); + + /* Noise floor threshold */ + ath5k_hw_reg_write(ah, + AR5K_PHY_NF_SVAL(ee->ee_noise_floor_thr[ee_mode]), + AR5K_PHY_NFTHRES); + + if ((channel->hw_value & CHANNEL_TURBO) && + (ah->ah_ee_version >= AR5K_EEPROM_VERSION_5_0)) { + /* Switch settling time (Turbo) */ + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_SETTLING, + AR5K_PHY_SETTLING_SWITCH, + ee->ee_switch_settling_turbo[ee_mode]); + + /* Tx/Rx attenuation (Turbo) */ + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_GAIN, + AR5K_PHY_GAIN_TXRX_ATTEN, + ee->ee_atn_tx_rx_turbo[ee_mode]); + + /* ADC/PGA dezired size (Turbo) */ + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_DESIRED_SIZE, + AR5K_PHY_DESIRED_SIZE_ADC, + ee->ee_adc_desired_size_turbo[ee_mode]); + + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_DESIRED_SIZE, + AR5K_PHY_DESIRED_SIZE_PGA, + ee->ee_pga_desired_size_turbo[ee_mode]); + + /* Tx/Rx margin (Turbo) */ + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_GAIN_2GHZ, + AR5K_PHY_GAIN_2GHZ_MARGIN_TXRX, + ee->ee_margin_tx_rx_turbo[ee_mode]); + + } else { + /* Switch settling time */ + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_SETTLING, + AR5K_PHY_SETTLING_SWITCH, + ee->ee_switch_settling[ee_mode]); + + /* Tx/Rx attenuation */ + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_GAIN, + AR5K_PHY_GAIN_TXRX_ATTEN, + ee->ee_atn_tx_rx[ee_mode]); + + /* ADC/PGA dezired size */ + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_DESIRED_SIZE, + AR5K_PHY_DESIRED_SIZE_ADC, + ee->ee_adc_desired_size[ee_mode]); + + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_DESIRED_SIZE, + AR5K_PHY_DESIRED_SIZE_PGA, + ee->ee_pga_desired_size[ee_mode]); + + /* Tx/Rx margin */ + if (ah->ah_ee_version >= AR5K_EEPROM_VERSION_4_1) + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_GAIN_2GHZ, + AR5K_PHY_GAIN_2GHZ_MARGIN_TXRX, + ee->ee_margin_tx_rx[ee_mode]); + } + + /* XPA delays */ + ath5k_hw_reg_write(ah, + (ee->ee_tx_end2xpa_disable[ee_mode] << 24) | + (ee->ee_tx_end2xpa_disable[ee_mode] << 16) | + (ee->ee_tx_frm2xpa_enable[ee_mode] << 8) | + (ee->ee_tx_frm2xpa_enable[ee_mode]), AR5K_PHY_RF_CTL4); + + /* XLNA delay */ + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_RF_CTL3, + AR5K_PHY_RF_CTL3_TXE2XLNA_ON, + ee->ee_tx_end2xlna_enable[ee_mode]); + + /* Thres64 (ANI) */ + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_NF, + AR5K_PHY_NF_THRESH62, + ee->ee_thr_62[ee_mode]); + + + /* False detect backoff for channels + * that have spur noise. Write the new + * cyclic power RSSI threshold. */ + if (ath5k_hw_chan_has_spur_noise(ah, channel)) + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_OFDM_SELFCORR, + AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1, + AR5K_INIT_CYCRSSI_THR1 + + ee->ee_false_detect[ee_mode]); + else + AR5K_REG_WRITE_BITS(ah, AR5K_PHY_OFDM_SELFCORR, + AR5K_PHY_OFDM_SELFCORR_CYPWR_THR1, + AR5K_INIT_CYCRSSI_THR1); + + /* I/Q correction + * TODO: Per channel i/q infos ? */ + AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, + AR5K_PHY_IQ_CORR_ENABLE | + (ee->ee_i_cal[ee_mode] << AR5K_PHY_IQ_CORR_Q_I_COFF_S) | + ee->ee_q_cal[ee_mode]); + + /* Heavy clipping -disable for now */ + if (ah->ah_ee_version >= AR5K_EEPROM_VERSION_5_1) + ath5k_hw_reg_write(ah, 0, AR5K_PHY_HEAVY_CLIP_ENABLE); + + return; +} + +/* * Main reset function */ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, struct ieee80211_channel *channel, bool change_channel) { - struct ath5k_eeprom_info *ee = &ah->ah_capabilities.cap_eeprom; - struct pci_dev *pdev = ah->ah_sc->pdev; - u32 data, s_seq, s_ant, s_led[3], dma_size; - unsigned int i, mode, freq, ee_mode, ant[2]; - int ret; + u32 s_seq[10], s_ant, s_led[3], staid1_flags, tsf_up, tsf_lo; + u32 data, rssi_thr; + u8 mode, freq, ee_mode, ant[2]; + int i, ret; ATH5K_TRACE(ah->ah_sc); - s_seq = 0; s_ant = 0; ee_mode = 0; + staid1_flags = 0; + tsf_up = 0; + tsf_lo = 0; freq = 0; mode = 0; @@ -427,36 +834,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, */ /*DCU/Antenna selection not available on 5210*/ if (ah->ah_version != AR5K_AR5210) { - if (change_channel) { - /* Seq number for queue 0 -do this for all queues ? */ - s_seq = ath5k_hw_reg_read(ah, - AR5K_QUEUE_DFS_SEQNUM(0)); - /*Default antenna*/ - s_ant = ath5k_hw_reg_read(ah, AR5K_DEFAULT_ANTENNA); - } - } - - /*GPIOs*/ - s_led[0] = ath5k_hw_reg_read(ah, AR5K_PCICFG) & AR5K_PCICFG_LEDSTATE; - s_led[1] = ath5k_hw_reg_read(ah, AR5K_GPIOCR); - s_led[2] = ath5k_hw_reg_read(ah, AR5K_GPIODO); - - - /*Wakeup the device*/ - ret = ath5k_hw_nic_wakeup(ah, channel->hw_value, false); - if (ret) - return ret; - - /* - * Initialize operating mode - */ - ah->ah_op_mode = op_mode; - - /* - * 5111/5112 Settings - * 5210 only comes with RF5110 - */ - if (ah->ah_version != AR5K_AR5210) { switch (channel->hw_value & CHANNEL_MODES) { case CHANNEL_A: @@ -479,8 +856,12 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, freq = AR5K_INI_RFGAIN_5GHZ; ee_mode = AR5K_EEPROM_MODE_11A; break; - /*Is this ok on 5211 too ?*/ case CHANNEL_TG: + if (ah->ah_version == AR5K_AR5211) { + ATH5K_ERR(ah->ah_sc, + "TurboG mode not available on 5211"); + return -EINVAL; + } mode = AR5K_MODE_11G_TURBO; freq = AR5K_INI_RFGAIN_2GHZ; ee_mode = AR5K_EEPROM_MODE_11G; @@ -501,11 +882,100 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, return -EINVAL; } + if (change_channel) { + /* + * Save frame sequence count + * For revs. after Oahu, only save + * seq num for DCU 0 (Global seq num) + */ + if (ah->ah_mac_srev < AR5K_SREV_AR5211) { + + for (i = 0; i < 10; i++) + s_seq[i] = ath5k_hw_reg_read(ah, + AR5K_QUEUE_DCU_SEQNUM(i)); + + } else { + s_seq[0] = ath5k_hw_reg_read(ah, + AR5K_QUEUE_DCU_SEQNUM(0)); + } + + /* TSF accelerates on AR5211 durring reset + * As a workaround save it here and restore + * it later so that it's back in time after + * reset. This way it'll get re-synced on the + * next beacon without breaking ad-hoc. + * + * On AR5212 TSF is almost preserved across a + * reset so it stays back in time anyway and + * we don't have to save/restore it. + * + * XXX: Since this breaks power saving we have + * to disable power saving until we receive the + * next beacon, so we can resync beacon timers */ + if (ah->ah_version == AR5K_AR5211) { + tsf_up = ath5k_hw_reg_read(ah, AR5K_TSF_U32); + tsf_lo = ath5k_hw_reg_read(ah, AR5K_TSF_L32); + } + } + + /* Save default antenna */ + s_ant = ath5k_hw_reg_read(ah, AR5K_DEFAULT_ANTENNA); + + /* AR5K_STA_ID1 flags, only preserve antenna and + * ack/cts rate mode */ + staid1_flags = ath5k_hw_reg_read(ah, AR5K_STA_ID1) & + (AR5K_STA_ID1_DEFAULT_ANTENNA | + AR5K_STA_ID1_DESC_ANTENNA | + AR5K_STA_ID1_RTS_DEF_ANTENNA | + AR5K_STA_ID1_ACKCTS_6MB | + AR5K_STA_ID1_BASE_RATE_11B | + AR5K_STA_ID1_SELFGEN_DEF_ANT); + + if (ah->ah_version == AR5K_AR5212) { + /* Restore normal 32/40MHz clock operation + * to avoid register access delay on certain + * PHY registers */ + ath5k_hw_set_sleep_clock(ah, false); + + /* Since we are going to write rf buffer + * check if we have any pending gain_F + * optimization settings */ + if (change_channel && ah->ah_rf_banks != NULL) + ath5k_hw_gainf_calibrate(ah); + } } + /*GPIOs*/ + s_led[0] = ath5k_hw_reg_read(ah, AR5K_PCICFG) & + AR5K_PCICFG_LEDSTATE; + s_led[1] = ath5k_hw_reg_read(ah, AR5K_GPIOCR); + s_led[2] = ath5k_hw_reg_read(ah, AR5K_GPIODO); + + /* Save RSSI thresholds (they 'll get zeroed from initvals) */ + rssi_thr = ath5k_hw_reg_read(ah, AR5K_RSSI_THR); + /* If they are not set, set the default value */ + if (!rssi_thr) + rssi_thr = AR5K_INIT_RSSI_THR; + + + /* Wakeup the device */ + ret = ath5k_hw_nic_wakeup(ah, channel->hw_value, false); + if (ret) + return ret; + + /* + * Initialize operating mode + */ + ah->ah_op_mode = op_mode; + /* PHY access enable */ - ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0)); + if (ah->ah_mac_srev >= AR5K_SREV_AR5211) + ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ, AR5K_PHY(0)); + else + ath5k_hw_reg_write(ah, AR5K_PHY_SHIFT_5GHZ | 0x40, + AR5K_PHY(0)); + /* Write initial settings */ ret = ath5k_hw_write_initvals(ah, mode, change_channel); if (ret) return ret; @@ -514,6 +984,7 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, * 5211/5212 Specific */ if (ah->ah_version != AR5K_AR5210) { + /* * Write initial RF gain settings * This should work for both 5111/5112 @@ -525,53 +996,11 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, mdelay(1); /* - * Write some more initial register settings for revised chips + * Tweak initval settings for revised + * chipsets and add some more config + * bits */ - if (ah->ah_version == AR5K_AR5212 && - ah->ah_phy_revision > 0x41) { - ath5k_hw_reg_write(ah, 0x0002a002, 0x982c); - - if (channel->hw_value == CHANNEL_G) - if (ah->ah_mac_srev < AR5K_SREV_AR2413) - ath5k_hw_reg_write(ah, 0x00f80d80, - 0x994c); - else if (ah->ah_mac_srev < AR5K_SREV_AR5424) - ath5k_hw_reg_write(ah, 0x00380140, - 0x994c); - else if (ah->ah_mac_srev < AR5K_SREV_AR2425) - ath5k_hw_reg_write(ah, 0x00fc0ec0, - 0x994c); - else /* 2425 */ - ath5k_hw_reg_write(ah, 0x00fc0fc0, - 0x994c); - else - ath5k_hw_reg_write(ah, 0x00000000, 0x994c); - - /* Got this from legacy-hal */ - AR5K_REG_DISABLE_BITS(ah, 0xa228, 0x200); - - AR5K_REG_MASKED_BITS(ah, 0xa228, 0x800, 0xfffe03ff); - - /* Just write 0x9b5 ? */ - /* ath5k_hw_reg_write(ah, 0x000009b5, 0xa228); */ - ath5k_hw_reg_write(ah, 0x0000000f, AR5K_SEQ_MASK); - ath5k_hw_reg_write(ah, 0x00000000, 0xa254); - ath5k_hw_reg_write(ah, 0x0000000e, AR5K_PHY_SCAL); - } - - /* Fix for first revision of the RF5112 RF chipset */ - if (ah->ah_radio >= AR5K_RF5112 && - ah->ah_radio_5ghz_revision < - AR5K_SREV_RAD_5112A) { - ath5k_hw_reg_write(ah, AR5K_PHY_CCKTXCTL_WORLD, - AR5K_PHY_CCKTXCTL); - if (channel->hw_value & CHANNEL_5GHZ) - data = 0xffb81020; - else - data = 0xffb80d20; - ath5k_hw_reg_write(ah, data, AR5K_PHY_FRAME_CTL); - data = 0; - } + ath5k_hw_tweak_initval_settings(ah, channel); /* * Set TX power (FIXME) @@ -589,15 +1018,12 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, ath5k_hw_write_rate_duration(ah, mode); /* - * Write RF registers + * Write RF buffer */ ret = ath5k_hw_rfregs_init(ah, channel, mode); if (ret) return ret; - /* - * Configure additional registers - */ /* Write OFDM timings on 5212*/ if (ah->ah_version == AR5K_AR5212 && @@ -619,17 +1045,6 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, } /* - * Set channel and calibrate the PHY - */ - ret = ath5k_hw_channel(ah, channel); - if (ret) - return ret; - - /* Set antenna mode */ - AR5K_REG_MASKED_BITS(ah, AR5K_PHY_ANT_CTL, - ah->ah_antenna[ee_mode][0], 0xfffffc06); - - /* * In case a fixed antenna was set as default * write the same settings on both AR5K_PHY_ANT_SWITCH_TABLE * registers. @@ -644,54 +1059,16 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, ant[1] = AR5K_ANT_FIXED_B; } - ath5k_hw_reg_write(ah, ah->ah_antenna[ee_mode][ant[0]], - AR5K_PHY_ANT_SWITCH_TABLE_0); - ath5k_hw_reg_write(ah, ah->ah_antenna[ee_mode][ant[1]], - AR5K_PHY_ANT_SWITCH_TABLE_1); - /* Commit values from EEPROM */ - if (ah->ah_radio == AR5K_RF5111) - AR5K_REG_WRITE_BITS(ah, AR5K_PHY_FRAME_CTL, - AR5K_PHY_FRAME_CTL_TX_CLIP, ee->ee_tx_clip); - - ath5k_hw_reg_write(ah, - AR5K_PHY_NF_SVAL(ee->ee_noise_floor_thr[ee_mode]), - AR5K_PHY_NFTHRES); - - AR5K_REG_MASKED_BITS(ah, AR5K_PHY_SETTLING, - (ee->ee_switch_settling[ee_mode] << 7) & 0x3f80, - 0xffffc07f); - AR5K_REG_MASKED_BITS(ah, AR5K_PHY_GAIN, - (ee->ee_atn_tx_rx[ee_mode] << 12) & 0x3f000, - 0xfffc0fff); - AR5K_REG_MASKED_BITS(ah, AR5K_PHY_DESIRED_SIZE, - (ee->ee_adc_desired_size[ee_mode] & 0x00ff) | - ((ee->ee_pga_desired_size[ee_mode] << 8) & 0xff00), - 0xffff0000); - - ath5k_hw_reg_write(ah, - (ee->ee_tx_end2xpa_disable[ee_mode] << 24) | - (ee->ee_tx_end2xpa_disable[ee_mode] << 16) | - (ee->ee_tx_frm2xpa_enable[ee_mode] << 8) | - (ee->ee_tx_frm2xpa_enable[ee_mode]), AR5K_PHY_RF_CTL4); - - AR5K_REG_MASKED_BITS(ah, AR5K_PHY_RF_CTL3, - ee->ee_tx_end2xlna_enable[ee_mode] << 8, 0xffff00ff); - AR5K_REG_MASKED_BITS(ah, AR5K_PHY_NF, - (ee->ee_thr_62[ee_mode] << 12) & 0x7f000, 0xfff80fff); - AR5K_REG_MASKED_BITS(ah, AR5K_PHY_OFDM_SELFCORR, 4, 0xffffff01); - - AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_IQ, - AR5K_PHY_IQ_CORR_ENABLE | - (ee->ee_i_cal[ee_mode] << AR5K_PHY_IQ_CORR_Q_I_COFF_S) | - ee->ee_q_cal[ee_mode]); - - if (ah->ah_ee_version >= AR5K_EEPROM_VERSION_4_1) - AR5K_REG_WRITE_BITS(ah, AR5K_PHY_GAIN_2GHZ, - AR5K_PHY_GAIN_2GHZ_MARGIN_TXRX, - ee->ee_margin_tx_rx[ee_mode]); + ath5k_hw_commit_eeprom_settings(ah, channel, ant, ee_mode); } else { + /* + * For 5210 we do all initialization using + * initvals, so we don't have to modify + * any settings (5210 also only supports + * a/aturbo modes) + */ mdelay(1); /* Disable phy and wait */ ath5k_hw_reg_write(ah, AR5K_PHY_ACT_DISABLE, AR5K_PHY_ACT); @@ -701,61 +1078,99 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, /* * Restore saved values */ + /*DCU/Antenna selection not available on 5210*/ if (ah->ah_version != AR5K_AR5210) { - ath5k_hw_reg_write(ah, s_seq, AR5K_QUEUE_DFS_SEQNUM(0)); + + if (ah->ah_mac_srev < AR5K_SREV_AR5211) { + for (i = 0; i < 10; i++) + ath5k_hw_reg_write(ah, s_seq[i], + AR5K_QUEUE_DCU_SEQNUM(i)); + } else { + ath5k_hw_reg_write(ah, s_seq[0], + AR5K_QUEUE_DCU_SEQNUM(0)); + } + + + if (ah->ah_version == AR5K_AR5211) { + ath5k_hw_reg_write(ah, tsf_up, AR5K_TSF_U32); + ath5k_hw_reg_write(ah, tsf_lo, AR5K_TSF_L32); + } + ath5k_hw_reg_write(ah, s_ant, AR5K_DEFAULT_ANTENNA); } + + /* Ledstate */ AR5K_REG_ENABLE_BITS(ah, AR5K_PCICFG, s_led[0]); + + /* Gpio settings */ ath5k_hw_reg_write(ah, s_led[1], AR5K_GPIOCR); ath5k_hw_reg_write(ah, s_led[2], AR5K_GPIODO); + /* RSSI thresholds */ + ath5k_hw_reg_write(ah, rssi_thr, AR5K_RSSI_THR); + + /* Restore sta_id flags and preserve our mac address*/ + ath5k_hw_reg_write(ah, AR5K_LOW_ID(ah->ah_sta_id), + AR5K_STA_ID0); + ath5k_hw_reg_write(ah, staid1_flags | AR5K_HIGH_ID(ah->ah_sta_id), + AR5K_STA_ID1); + + /* - * Misc + * Configure PCU */ + + /* Restore bssid and bssid mask */ /* XXX: add ah->aid once mac80211 gives this to us */ ath5k_hw_set_associd(ah, ah->ah_bssid, 0); + /* Set PCU config */ ath5k_hw_set_opmode(ah); - /*PISR/SISR Not available on 5210*/ + + /* Clear any pending interrupts + * PISR/SISR Not available on 5210 */ if (ah->ah_version != AR5K_AR5210) { ath5k_hw_reg_write(ah, 0xffffffff, AR5K_PISR); - /* If we later allow tuning for this, store into sc structure */ - data = AR5K_TUNE_RSSI_THRES | - AR5K_TUNE_BMISS_THRES << AR5K_RSSI_THR_BMISS_S; - ath5k_hw_reg_write(ah, data, AR5K_RSSI_THR); } + /* MIC QoS support */ + if (ah->ah_mac_srev >= AR5K_SREV_AR2413) { + ath5k_hw_reg_write(ah, 0x000100aa, AR5K_MIC_QOS_CTL); + ath5k_hw_reg_write(ah, 0x00003210, AR5K_MIC_QOS_SEL); + } + + /* QoS NOACK Policy */ + if (ah->ah_version == AR5K_AR5212) { + ath5k_hw_reg_write(ah, + AR5K_REG_SM(2, AR5K_QOS_NOACK_2BIT_VALUES) | + AR5K_REG_SM(5, AR5K_QOS_NOACK_BIT_OFFSET) | + AR5K_REG_SM(0, AR5K_QOS_NOACK_BYTE_OFFSET), + AR5K_QOS_NOACK); + } + + /* - * Set Rx/Tx DMA Configuration - * - * Set maximum DMA size (512) except for PCI-E cards since - * it causes rx overruns and tx errors (tested on 5424 but since - * rx overruns also occur on 5416/5418 with madwifi we set 128 - * for all PCI-E cards to be safe). - * - * In dumps this is 128 for allchips. - * - * XXX: need to check 5210 for this - * TODO: Check out tx triger level, it's always 64 on dumps but I - * guess we can tweak it and see how it goes ;-) + * Configure PHY */ - dma_size = (pdev->is_pcie) ? AR5K_DMASIZE_128B : AR5K_DMASIZE_512B; - if (ah->ah_version != AR5K_AR5210) { - AR5K_REG_WRITE_BITS(ah, AR5K_TXCFG, - AR5K_TXCFG_SDMAMR, dma_size); - AR5K_REG_WRITE_BITS(ah, AR5K_RXCFG, - AR5K_RXCFG_SDMAMW, dma_size); - } + + /* Set channel on PHY */ + ret = ath5k_hw_channel(ah, channel); + if (ret) + return ret; /* * Enable the PHY and wait until completion + * This includes BaseBand and Synthesizer + * activation. */ ath5k_hw_reg_write(ah, AR5K_PHY_ACT_ENABLE, AR5K_PHY_ACT); /* * On 5211+ read activation -> rx delay * and use it. + * + * TODO: Half/quarter rate support */ if (ah->ah_version != AR5K_AR5210) { data = ath5k_hw_reg_read(ah, AR5K_PHY_RX_DELAY) & @@ -770,7 +1185,8 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, } /* - * Perform ADC test (?) + * Perform ADC test to see if baseband is ready + * Set tx hold and check adc test register */ data = ath5k_hw_reg_read(ah, AR5K_PHY_TST1); ath5k_hw_reg_write(ah, AR5K_PHY_TST1_TXHOLD, AR5K_PHY_TST1); @@ -783,18 +1199,23 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, data = 0; /* - * Start automatic gain calibration + * Start automatic gain control calibration * * During AGC calibration RX path is re-routed to - * a signal detector so we don't receive anything. + * a power detector so we don't receive anything. * * This method is used to calibrate some static offsets * used together with on-the fly I/Q calibration (the * one performed via ath5k_hw_phy_calibrate), that doesn't * interrupt rx path. * + * While rx path is re-routed to the power detector we also + * start a noise floor calibration, to measure the + * card's noise floor (the noise we measure when we are not + * transmiting or receiving anything). + * * If we are in a noisy environment AGC calibration may time - * out. + * out and/or noise floor calibration might timeout. */ AR5K_REG_ENABLE_BITS(ah, AR5K_PHY_AGCCTL, AR5K_PHY_AGCCTL_CAL); @@ -816,30 +1237,37 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, AR5K_PHY_AGCCTL_CAL, 0, false)) { ATH5K_ERR(ah->ah_sc, "gain calibration timeout (%uMHz)\n", channel->center_freq); - return -EAGAIN; } /* - * Start noise floor calibration - * * If we run NF calibration before AGC, it always times out. * Binary HAL starts NF and AGC calibration at the same time - * and only waits for AGC to finish. I believe that's wrong because - * during NF calibration, rx path is also routed to a detector, so if - * it doesn't finish we won't have RX. - * - * XXX: Find an interval that's OK for all cards... + * and only waits for AGC to finish. Also if AGC or NF cal. + * times out, reset doesn't fail on binary HAL. I believe + * that's wrong because since rx path is routed to a detector, + * if cal. doesn't finish we won't have RX. Sam's HAL for AR5210/5211 + * enables noise floor calibration after offset calibration and if noise + * floor calibration fails, reset fails. I believe that's + * a better approach, we just need to find a polling interval + * that suits best, even if reset continues we need to make + * sure that rx path is ready. */ ath5k_hw_noise_floor_calibration(ah, channel->center_freq); + + /* + * Configure QCUs/DCUs + */ + + /* TODO: HW Compression support for data queues */ + /* TODO: Burst prefetch for data queues */ + /* * Reset queues and start beacon timers at the end of the reset routine + * This also sets QCU mask on each DCU for 1:1 qcu to dcu mapping + * Note: If we want we can assign multiple qcus on one dcu. */ for (i = 0; i < ah->ah_capabilities.cap_queues.q_tx_num; i++) { - /*No QCU on 5210*/ - if (ah->ah_version != AR5K_AR5210) - AR5K_REG_WRITE_Q(ah, AR5K_QUEUE_QCUMASK(i), i); - ret = ath5k_hw_reset_tx_queue(ah, i); if (ret) { ATH5K_ERR(ah->ah_sc, @@ -848,14 +1276,40 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, } } + + /* + * Configure DMA/Interrupts + */ + + /* + * Set Rx/Tx DMA Configuration + * + * Set standard DMA size (128). Note that + * a DMA size of 512 causes rx overruns and tx errors + * on pci-e cards (tested on 5424 but since rx overruns + * also occur on 5416/5418 with madwifi we set 128 + * for all PCI-E cards to be safe). + * + * XXX: need to check 5210 for this + * TODO: Check out tx triger level, it's always 64 on dumps but I + * guess we can tweak it and see how it goes ;-) + */ + if (ah->ah_version != AR5K_AR5210) { + AR5K_REG_WRITE_BITS(ah, AR5K_TXCFG, + AR5K_TXCFG_SDMAMR, AR5K_DMASIZE_128B); + AR5K_REG_WRITE_BITS(ah, AR5K_RXCFG, + AR5K_RXCFG_SDMAMW, AR5K_DMASIZE_128B); + } + /* Pre-enable interrupts on 5211/5212*/ if (ah->ah_version != AR5K_AR5210) ath5k_hw_set_imr(ah, ah->ah_imr); /* - * Set RF kill flags if supported by the device (read from the EEPROM) - * Disable gpio_intr for now since it results system hang. - * TODO: Handle this in ath5k_intr + * Setup RFKill interrupt if rfkill flag is set on eeprom. + * TODO: Use gpio pin and polarity infos from eeprom + * TODO: Handle this in ath5k_intr because it'll result + * a nasty interrupt storm. */ #if 0 if (AR5K_EEPROM_HDR_RFKILL(ah->ah_capabilities.cap_eeprom.ee_header)) { @@ -868,33 +1322,12 @@ int ath5k_hw_reset(struct ath5k_hw *ah, enum nl80211_iftype op_mode, } #endif - /* - * Set the 32MHz reference clock on 5212 phy clock sleep register - * - * TODO: Find out how to switch to external 32Khz clock to save power - */ - if (ah->ah_version == AR5K_AR5212) { - ath5k_hw_reg_write(ah, AR5K_PHY_SCR_32MHZ, AR5K_PHY_SCR); - ath5k_hw_reg_write(ah, AR5K_PHY_SLMT_32MHZ, AR5K_PHY_SLMT); - ath5k_hw_reg_write(ah, AR5K_PHY_SCAL_32MHZ, AR5K_PHY_SCAL); - ath5k_hw_reg_write(ah, AR5K_PHY_SCLOCK_32MHZ, AR5K_PHY_SCLOCK); - ath5k_hw_reg_write(ah, AR5K_PHY_SDELAY_32MHZ, AR5K_PHY_SDELAY); - ath5k_hw_reg_write(ah, ah->ah_phy_spending, AR5K_PHY_SPENDING); - - data = ath5k_hw_reg_read(ah, AR5K_USEC_5211) & 0xffffc07f ; - data |= (ah->ah_phy_spending == AR5K_PHY_SPENDING_18) ? - 0x00000f80 : 0x00001380 ; - ath5k_hw_reg_write(ah, data, AR5K_USEC_5211); - data = 0; - } - - if (ah->ah_version == AR5K_AR5212) { - ath5k_hw_reg_write(ah, 0x000100aa, 0x8118); - ath5k_hw_reg_write(ah, 0x00003210, 0x811c); - ath5k_hw_reg_write(ah, 0x00000052, 0x8108); - if (ah->ah_mac_srev >= AR5K_SREV_AR2413) - ath5k_hw_reg_write(ah, 0x00000004, 0x8120); - } + /* Enable 32KHz clock function for AR5212+ chips + * Set clocks to 32KHz operation and use an + * external 32KHz crystal when sleeping if one + * exists */ + if (ah->ah_version == AR5K_AR5212) + ath5k_hw_set_sleep_clock(ah, true); /* * Disable beacons and reset the register