Return-path: Received: from mail-fx0-f213.google.com ([209.85.220.213]:39182 "EHLO mail-fx0-f213.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751373AbZK2Q7w convert rfc822-to-8bit (ORCPT ); Sun, 29 Nov 2009 11:59:52 -0500 Received: by fxm5 with SMTP id 5so2966921fxm.28 for ; Sun, 29 Nov 2009 08:59:57 -0800 (PST) MIME-Version: 1.0 In-Reply-To: <4B127E9E.1090008@klingt.org> References: <4AE43028.30703@klingt.org> <4B127E9E.1090008@klingt.org> From: =?ISO-8859-1?Q?G=E1bor_Stefanik?= Date: Sun, 29 Nov 2009 17:59:36 +0100 Message-ID: <69e28c910911290859mc1da58ree7b2d3fa8dc371d@mail.gmail.com> Subject: Re: rt61pci bug To: Tim Blechmann Cc: linux-wireless@vger.kernel.org Content-Type: text/plain; charset=ISO-8859-1 Sender: linux-wireless-owner@vger.kernel.org List-ID: On Sun, Nov 29, 2009 at 3:01 PM, Tim Blechmann wrote: > On 11/04/2009 07:00 PM, Tim Blechmann wrote: >>> running the rt61pci module on 2.6.31.5 works fine, but using the recent >>> linus/master (2.6.32-rc5) results in this: >> >> same issue with 2.6.32-rc5 ... new bootlog with more debugging info >> attached ... > > i was still able to reproduce this issue with 2.6.32-rc8 ... it would > be nice, if someone could have a look into this issue before 2.6.32 is > released ... > > dmesg from 2.6.32-rc8: > [ ? 10.249098] rt61pci 0000:06:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 > [ ? 10.257182] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - NIC: 0xff80 > [ ? 10.257184] phy0 -> rt61pci_validate_eeprom: EEPROM recovery - Led: 0xe0ff > [ ? 10.257187] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 0302, rf: 0003, rev: 0002561c. > [ ? 10.351794] Registered led device: rt61pci-phy0::radio > [ ? 10.351839] Registered led device: rt61pci-phy0::assoc > [ ? 14.342046] rt61pci 0000:06:00.0: firmware: requesting rt2561.bin > [ ? 14.395533] phy0 -> rt2x00lib_request_firmware: Info - Firmware detected - version: 0.8. > [ ? 14.421238] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 102. > [ ? 14.421245] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 4, CWmax: 5, Aifs: 2, TXop: 188. > [ ? 14.421252] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 5, CWmax: 10, Aifs: 3, TXop: 0. > [ ? 14.421258] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 5, CWmax: 10, Aifs: 7, TXop: 0. > [ ?273.404685] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2. > [ ?273.404687] Please file bug report to http://rt2x00.serialmonkey.com. > [ ?282.143549] wlan0: no IPv6 routers present > [ ?357.304908] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 2 > [ ?357.333806] phy0 -> rt61pci_txdone: Warning - TX status report missed for entry 9 > [ ?360.172776] phy0 -> rt2x00queue_write_tx_frame: Error - Arrived at non-free entry in the non-full queue 2. > [ ?360.172778] Please file bug report to http://rt2x00.serialmonkey.com. > [ ?360.172782] phy0 -> rt2x00mac_tx_rts_cts: Warning - Failed to send RTS/CTS frame. > [ ?383.880010] No probe response from AP 00:24:fe:09:94:18 after 500ms, disconnecting. > [ ?383.880026] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 0 - CWmin: 2, CWmax: 3, Aifs: 2, TXop: 47. > [ ?383.880034] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 1 - CWmin: 3, CWmax: 4, Aifs: 2, TXop: 94. > [ ?383.880042] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 2 - CWmin: 4, CWmax: 10, Aifs: 3, TXop: 0. > [ ?383.880050] phy0 -> rt2x00mac_conf_tx: Info - Configured TX queue 3 - CWmin: 4, CWmax: 10, Aifs: 7, TXop: 0. > [ ?385.220460] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 1) > [ ?385.421337] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 2) > [ ?385.621304] wlan0: direct probe to AP 00:24:fe:09:94:18 (try 3) > [ ?385.821264] wlan0: direct probe to AP 00:24:fe:09:94:18 timed out > > > lspci -vvv: > > 06:00.0 Network controller: RaLink RT2561/RT61 rev B 802.11g > ? ? ? ?Subsystem: D-Link System Inc Device 3c09 > ? ? ? ?Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- > ? ? ? ?Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- SERR- ? ? ? ?Latency: 64, Cache Line Size: 64 bytes > ? ? ? ?Interrupt: pin A routed to IRQ 16 > ? ? ? ?Region 0: Memory at fb6f8000 (32-bit, non-prefetchable) [size=32K] > ? ? ? ?Capabilities: [40] Power Management version 2 > ? ? ? ? ? ? ? ?Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) > ? ? ? ? ? ? ? ?Status: D0 PME-Enable- DSel=0 DScale=0 PME- > ? ? ? ?Kernel driver in use: rt61pci > ? ? ? ?Kernel modules: rt61pci > > thanks, tim Could you please try a bisect between 2.6.31 and 2.6.32-rc5? That should reveal the faulty commit. > > -- > tim@klingt.org > http://tim.klingt.org > > Happiness is a byproduct of function, purpose, and conflict; those who > seek happiness for itself seek victory without war. > ?William S. Burroughs > > -- Vista: [V]iruses, [I]ntruders, [S]pyware, [T]rojans and [A]dware. :-)