Subject: 
From: Thijs van der Kraan <thijsvanderkraan@telfort.nl>
To: linux-wireless@vger.kernel.org
Content-Type: text/plain; charset="UTF-8"
Date: Sat, 13 Mar 2010 17:33:14 +0100
Message-ID: <1268497994.2475.12.camel@desktop>
Mime-Version: 1.0
Sender: linux-wireless-owner@vger.kernel.org

The zd1211rw does not work with the Shuttle PN15G (D-Link Corp. WL54).
After the driver fails it also break the device for my windows XP
install.
To get it back in working order I have to physically re-plug it while
windows is running, this is pretty annoying as the PN15G is meant to be,
and is, built inside my shuttle box.

I tried another device that uses the same driver, the ZyAIR G-220, and
it works like a charm.

- Is there a way to get the Shuttle PN15G working ?
- Can prevent the driver from breaking my device, so it will remain
working under windows XP.


Thijs van de Kraan


lsusb:
---------------
Bus 001 Device 004: ID 0586:3401 ZyXEL Communications Corp. ZyAIR G-220
Bus 001 Device 003: ID 07b8:6001 D-Link Corp. WL54
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 04fc:05d8 Sunplus Technology Co., Ltd 
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
---------------

dmesg (Shuttle PN15G):
---------------
[    9.419022] zd1211rw 1-8:1.0: phy0
[    9.419050] usbcore: registered new interface driver zd1211rw
[   11.618783] usb 1-8: firmware: requesting zd1211/zd1211b_ub
[   11.979913] usb 1-8: firmware version 0x4810 and device bootcode
version 0x4721 differ
[   11.979919] usb 1-8: firmware: requesting zd1211/zd1211b_ur
[   12.184918] usb 1-8: firmware: requesting zd1211/zd1211b_uphr
[   12.261522] zd1211rw 1-8:1.0: RF2959 is currently not supported for
ZD1211B devices
[   12.263744] eth0: link down
[   12.263950] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   14.491044] usb 1-8: firmware: requesting zd1211/zd1211b_ub
[   14.496834] usb 1-8: firmware version 0x4810 and device bootcode
version 0x4721 differ
[   14.496841] usb 1-8: firmware: requesting zd1211/zd1211b_ur
[   15.526035] usb 1-8: USB control request for firmware upload failed.
Error number -110
[   15.526049] zd1211rw 1-8:1.0: couldn't load firmware. Error number
-110

dmesg (ZyAIR G-220):
---------------

[  283.920025] usb 1-4: new high speed USB device using ehci_hcd and
address 4
[  284.070953] usb 1-4: configuration #1 chosen from 1 choice
[  284.200081] usb 1-4: reset high speed USB device using ehci_hcd and
address 4
[  284.351553] phy1: Selected rate control algorithm 'minstrel'
[  284.352966] zd1211rw 1-4:1.0: phy1
[  284.387607] usb 1-4: firmware: requesting zd1211/zd1211_ub
[  284.422786] usb 1-4: firmware version 0x4330 and device bootcode
version 0x4810 differ
[  284.422796] usb 1-4: firmware: requesting zd1211/zd1211_ur
[  284.446550] usb 1-4: firmware: requesting zd1211/zd1211_uphr
[  284.528039] zd1211rw 1-4:1.0: firmware version 4605
[  284.568044] zd1211rw 1-4:1.0: zd1211 chip 0586:3401 v4810 high
00-13-49 AL2230_RF pa0 -----
[  284.570691] cfg80211: Calling CRDA for country: DE
[  284.574176] cfg80211: Regulatory domain changed to country: DE
[  284.574184] 	(start_freq - end_freq @ bandwidth), (max_antenna_gain,
max_eirp)
[  284.574190] 	(2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  284.574195] 	(5150000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[  284.574200] 	(5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm)
[  284.589627] ADDRCONF(NETDEV_UP): wlan1: link is not ready
[  291.145078] wlan1: authenticate with AP 00:21:29:8b:3a:49
[  291.146703] wlan1: authenticated
[  291.146708] wlan1: associate with AP 00:21:29:8b:3a:49
[  291.148944] wlan1: RX AssocResp from 00:21:29:8b:3a:49 (capab=0x411
status=0 aid=2)
[  291.148950] wlan1: associated
[  291.149928] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[  301.720021] wlan1: no IPv6 routers present