Return-path: Received: from server.heaven-czfree.net ([78.108.102.201]:49598 "EHLO smtp.heaven-czfree.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1752588Ab0GBRam (ORCPT ); Fri, 2 Jul 2010 13:30:42 -0400 Received: from [10.23.202.43] (unknown [10.23.202.43]) by smtp.heaven-czfree.net (Postfix) with ESMTP id 957D5147657 for ; Fri, 2 Jul 2010 19:30:40 +0200 (CEST) From: "Jaroslav Fojtik" To: linux-wireless@vger.kernel.org Date: Fri, 02 Jul 2010 19:33:15 +0200 MIME-Version: 1.0 Subject: How to enable channels 12,13? Message-ID: <4C2E22DB.13996.20C5ABD@jafojtik.seznam.cz> Content-type: text/plain; charset=US-ASCII Sender: linux-wireless-owner@vger.kernel.org List-ID: Dears, My device ignores channels 12,13, but they are allowed in our country. Is it possible to shut down defective regdomain policy? The proper regdomain is already set: [ 5.809776] ath5k 0000:02:0a.0: registered as 'phy1' [ 6.276736] ath: EEPROM regdomain: 0x36 ..... [ 5.152196] ath5k 0000:02:08.0: registered as 'phy0' [ 5.749710] ath: EEPROM regdomain: 0x36 ..... [ 6.278376] ath5k phy1: Atheros AR5213A chip found (MAC: 0x59, PHY: 0x43) [ 6.278440] ath5k phy1: RF5112B multiband radio found (0x36) [ 6.278539] ath5k 0000:02:0b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 6.278679] ath5k 0000:02:0b.0: registered as 'phy2' [ 6.745533] ath: EEPROM regdomain: 0x36 [ 6.745538] ath: EEPROM indicates we should expect a direct regpair map [ 6.745547] ath: Country alpha2 being used: CZ [ 6.745553] ath: Regpair used: 0x36 [ 6.745661] cfg80211: Calling CRDA for country: CZ Strange ??? root@dvouramenna:~# iw reg get country 00: (2402 - 2472 @ 40), (6, 20) (2457 - 2482 @ 20), (6, 20), PASSIVE-SCAN, NO-IBSS (2474 - 2494 @ 20), (6, 20), NO-OFDM, PASSIVE-SCAN, NO-IBSS (5170 - 5250 @ 40), (6, 20), PASSIVE-SCAN, NO-IBSS (5735 - 5835 @ 40), (6, 20), PASSIVE-SCAN, NO-IBSS Hmmm?? What is it: root@dvouramenna:~# iw reg set CZ root@dvouramenna:~# iw reg get country 00: (2402 - 2472 @ 40), (6, 20) (2457 - 2482 @ 20), (6, 20), PASSIVE-SCAN, NO-IBSS (2474 - 2494 @ 20), (6, 20), NO-OFDM, PASSIVE-SCAN, NO-IBSS (5170 - 5250 @ 40), (6, 20), PASSIVE-SCAN, NO-IBSS (5735 - 5835 @ 40), (6, 20), PASSIVE-SCAN, NO-IBSS Even attempt of rewriting regdomain shows that a device has proper domain in EEPROM: root@dvouramenna:~#ath_info -g 1:0 -w 0xfdee0000 regdomain 36 ...................................... new GPIO CR 00000303 DO 00000001 DI 00000007 regdomain (0x00bf) := 0x0036 WARNING: The write function may easy brick your device or violate state regulation on frequency usage. Proceed on your own risk! Shall I write the above value(s)? (y/n) y pair 0: skipped, value already there restoring GPIO CR 303 -> 3 But channels are somehow blocked from unknown reason. regards Jara iw list: Wiphy phy1 Band 1: Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (disabled) * 2472 MHz [13] (disabled) * 2484 MHz [14] (disabled) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps Band 2: Frequencies: * 5180 MHz [36] (30.0 dBm) * 5200 MHz [40] (30.0 dBm) (passive scanning, no IBSS) * 5220 MHz [44] (30.0 dBm) (passive scanning, no IBSS) * 5240 MHz [48] (30.0 dBm) (passive scanning, no IBSS) * 5260 MHz [52] (30.0 dBm) (passive scanning, no IBSS, radar detection) * 5280 MHz [56] (30.0 dBm) (passive scanning, no IBSS, radar detection) * 5300 MHz [60] (30.0 dBm) (passive scanning, no IBSS, radar detection) * 5320 MHz [64] (30.0 dBm) (passive scanning, no IBSS, radar detection) * 5500 MHz [100] (disabled) * 5520 MHz [104] (disabled) * 5540 MHz [108] (disabled) * 5560 MHz [112] (disabled) * 5580 MHz [116] (disabled) * 5600 MHz [120] (disabled) * 5620 MHz [124] (disabled) * 5640 MHz [128] (disabled) * 5660 MHz [132] (disabled) * 5680 MHz [136] (disabled) * 5700 MHz [140] (disabled) * 5745 MHz [149] (30.0 dBm) (passive scanning, no IBSS) * 5765 MHz [153] (30.0 dBm) (passive scanning, no IBSS) * 5785 MHz [157] (30.0 dBm) (passive scanning, no IBSS) * 5805 MHz [161] (30.0 dBm) (passive scanning, no IBSS) * 5825 MHz [165] (30.0 dBm) (passive scanning, no IBSS) Bitrates (non-HT): * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 Supported interface modes: * IBSS * managed * AP * AP/VLAN * monitor * mesh point Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * Unknown command (55) * Unknown command (57) * Unknown command (59) * set_wiphy_netns * Unknown command (65) * connect * disconnect Wiphy phy0 Band 1: Frequencies: * 2412 MHz [1] (20.0 dBm) * 2417 MHz [2] (20.0 dBm) * 2422 MHz [3] (20.0 dBm) * 2427 MHz [4] (20.0 dBm) * 2432 MHz [5] (20.0 dBm) * 2437 MHz [6] (20.0 dBm) * 2442 MHz [7] (20.0 dBm) * 2447 MHz [8] (20.0 dBm) * 2452 MHz [9] (20.0 dBm) * 2457 MHz [10] (20.0 dBm) * 2462 MHz [11] (20.0 dBm) * 2467 MHz [12] (disabled) * 2472 MHz [13] (disabled) * 2484 MHz [14] (disabled) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 Supported interface modes: * IBSS * managed * AP * AP/VLAN * monitor * mesh point Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * Unknown command (55) * Unknown command (57) * Unknown command (59) * set_wiphy_netns * Unknown command (65) * connect * disconnect root@dvouramenna:~#