Return-path: Received: from mail-gw0-f46.google.com ([74.125.83.46]:62742 "EHLO mail-gw0-f46.google.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1754062Ab1GQSkS (ORCPT ); Sun, 17 Jul 2011 14:40:18 -0400 Received: by gwaa18 with SMTP id a18so1060694gwa.19 for ; Sun, 17 Jul 2011 11:40:18 -0700 (PDT) MIME-Version: 1.0 Date: Sun, 17 Jul 2011 12:40:18 -0600 Message-ID: (sfid-20110717_204025_373769_797A62C0) Subject: Help with Atheros AR9285 Rev:2 Fails to initialize radio UBNT AirRouter From: Kelly Hogan To: linux-wireless@vger.kernel.org Content-Type: text/plain; charset=ISO-8859-1 Sender: linux-wireless-owner@vger.kernel.org List-ID: Hello All, We're compiling latest openwrt trunk, and attempting to get it to run on the UBNT AirRouter. This is an AR9285 chipset, and all looks good until we try to initialize the radio device and get: ath: Unable to reset hardware; reset status -5 (freq 2412 MHz) dmesg shows that root@OpenWrt:/etc/config# dmesg | grep ath ath: EEPROM regdomain: 0x0 ath: EEPROM indicates default country code should be used ath: doing EEPROM country->regdmn map search ath: country maps to regdmn code: 0x3a ath: Country alpha2 being used: US ath: Regpair used: 0x3a Registered led device: ath9k-phy0 and iw list (below) shows the device, but any attempts to bring it or vifs up fail. It seems that the problem is in the calibration/initialization process, but any network attempts give the: ath: Unable to reset hardware; reset status -5 (freq 2412 MHz) Were new to this, but will dive in if a few pointers of where to look would give us some initial direction. Thanks! root@OpenWrt:/etc/config# iw list Wiphy phy0 Band 1: Capabilities: 0x11ce HT20/HT40 SM Power Save disabled RX HT40 SGI TX STBC RX STBC 1-stream Max AMSDU length: 3839 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 8 usec (0x06) HT RX MCS rate indexes supported: 0-15 TX unequal modulation not supported HT TX Max spatial streams: 1 HT TX MCS rate indexes supported may differ Frequencies: * 2412 MHz [1] (27.0 dBm) * 2417 MHz [2] (27.0 dBm) * 2422 MHz [3] (27.0 dBm) * 2427 MHz [4] (27.0 dBm) * 2432 MHz [5] (27.0 dBm) * 2437 MHz [6] (27.0 dBm) * 2442 MHz [7] (27.0 dBm) * 2447 MHz [8] (27.0 dBm) * 2452 MHz [9] (27.0 dBm) * 2457 MHz [10] (27.0 dBm) * 2462 MHz [11] (27.0 dBm) * 2467 MHz [12] (disabled) * 2472 MHz [13] (disabled) * 2484 MHz [14] (disabled) Bitrates (non-HT): * 1.0 Mbps * 2.0 Mbps (short preamble supported) * 5.5 Mbps (short preamble supported) * 11.0 Mbps (short preamble supported) * 6.0 Mbps * 9.0 Mbps * 12.0 Mbps * 18.0 Mbps * 24.0 Mbps * 36.0 Mbps * 48.0 Mbps * 54.0 Mbps max # scan SSIDs: 4 max scan IEs length: 2257 bytes Coverage class: 0 (up to 0m) Available Antennas: TX 0 RX 0 Supported interface modes: * IBSS * managed * AP * AP/VLAN * WDS * monitor * mesh point * P2P-client * P2P-GO Supported commands: * new_interface * set_interface * new_key * new_beacon * new_station * new_mpath * set_mesh_params * set_bss * authenticate * associate * deauthenticate * disassociate * join_ibss * join_mesh * remain_on_channel * set_tx_bitrate_mask * action * frame_wait_cancel * set_wiphy_netns * set_channel * set_wds_peer * connect * disconnect Supported TX frame types: * IBSS: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * managed: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * AP/VLAN: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * mesh point: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-client: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 * P2P-GO: 0x0000 0x0010 0x0020 0x0030 0x0040 0x0050 0x0060 0x0070 0x0080 0x0090 0x00a0 0x00b0 0x00c0 0x00d0 0x00e0 0x00f0 Supported RX frame types: * IBSS: 0x00d0 * managed: 0x0040 0x00d0 * AP: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * AP/VLAN: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0 * mesh point: 0x00b0 0x00c0 0x00d0 * P2P-client: 0x0040 0x00d0 * P2P-GO: 0x0000 0x0020 0x0040 0x00a0 0x00b0 0x00c0 0x00d0