Return-path: Received: from wolverine02.qualcomm.com ([199.106.114.251]:48352 "EHLO wolverine02.qualcomm.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1751151Ab2HJLSL (ORCPT ); Fri, 10 Aug 2012 07:18:11 -0400 From: Sujith Manoharan MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Message-ID: <20516.60841.53051.293378@gargle.gargle.HOWL> (sfid-20120810_131815_765315_F47F0240) Date: Fri, 10 Aug 2012 16:46:57 +0530 To: CC: Subject: [PATCH 10/15] ath9k: Fix RTS/CTS rate selection Sender: linux-wireless-owner@vger.kernel.org List-ID: The current method of assigning the RTS/CTS rate is completely broken for HT mode and breaks P2P operation. Fix this by using the basic_rates provided to the driver by mac80211. For now, choose the lowest supported basic rate for HT frames. Signed-off-by: Sujith Manoharan --- drivers/net/wireless/ath/ath9k/rc.c | 41 +++++++++++++------------------------ 1 file changed, 14 insertions(+), 27 deletions(-) diff --git a/drivers/net/wireless/ath/ath9k/rc.c b/drivers/net/wireless/ath/ath9k/rc.c index 78192c1..a94c52b 100644 --- a/drivers/net/wireless/ath/ath9k/rc.c +++ b/drivers/net/wireless/ath/ath9k/rc.c @@ -699,37 +699,25 @@ static void ath_rc_rate_set_rtscts(struct ath_softc *sc, const struct ath_rate_table *rate_table, struct ieee80211_tx_info *tx_info) { - struct ieee80211_tx_rate *rates = tx_info->control.rates; - int i = 0, rix = 0, cix, enable_g_protection = 0; + struct ieee80211_bss_conf *bss_conf; - /* get the cix for the lowest valid rix */ - for (i = 3; i >= 0; i--) { - if (rates[i].count && (rates[i].idx >= 0)) { - rix = ath_rc_get_rateindex(rate_table, &rates[i]); - break; - } - } - cix = rate_table->info[rix].ctrl_rate; + if (!tx_info->control.vif) + return; + /* + * For legacy frames, mac80211 takes care of CTS protection. + */ + if (!(tx_info->control.rates[0].flags & IEEE80211_TX_RC_MCS)) + return; + + bss_conf = &tx_info->control.vif->bss_conf; - /* All protection frames are transmited at 2Mb/s for 802.11g, - * otherwise we transmit them at 1Mb/s */ - if (sc->hw->conf.channel->band == IEEE80211_BAND_2GHZ && - !conf_is_ht(&sc->hw->conf)) - enable_g_protection = 1; + if (!bss_conf->basic_rates) + return; /* - * If 802.11g protection is enabled, determine whether to use RTS/CTS or - * just CTS. Note that this is only done for OFDM/HT unicast frames. + * For now, use the lowest allowed basic rate for HT frames. */ - if ((tx_info->control.vif && - tx_info->control.vif->bss_conf.use_cts_prot) && - (rate_table->info[rix].phy == WLAN_RC_PHY_OFDM || - WLAN_RC_PHY_HT(rate_table->info[rix].phy))) { - rates[0].flags |= IEEE80211_TX_RC_USE_CTS_PROTECT; - cix = rate_table->info[enable_g_protection].ctrl_rate; - } - - tx_info->control.rts_cts_rate_idx = cix; + tx_info->control.rts_cts_rate_idx = __ffs(bss_conf->basic_rates); } static void ath_get_rate(void *priv, struct ieee80211_sta *sta, void *priv_sta, @@ -853,7 +841,6 @@ static void ath_get_rate(void *priv, struct ieee80211_sta *sta, void *priv_sta, rates[0].count = ATH_TXMAXTRY; } - /* Setup RTS/CTS */ ath_rc_rate_set_rtscts(sc, rate_table, tx_info); } -- 1.7.11.4