Return-path: Received: from eusmtp01.atmel.com ([212.144.249.242]:28249 "EHLO eusmtp01.atmel.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1756941AbbIVFcn (ORCPT ); Tue, 22 Sep 2015 01:32:43 -0400 From: Glen Lee To: CC: , , , , , , , , , , , Subject: [PATCH v3 3/4] staging: wilc1000: wilc_wlan_if.h: remove warnings line over 80 characters Date: Tue, 22 Sep 2015 14:34:45 +0900 Message-ID: <1442900086-9480-3-git-send-email-glen.lee@atmel.com> (sfid-20150922_073247_024741_32A86F39) In-Reply-To: <1442900086-9480-1-git-send-email-glen.lee@atmel.com> References: <1442900086-9480-1-git-send-email-glen.lee@atmel.com> MIME-Version: 1.0 Content-Type: text/plain Sender: linux-wireless-owner@vger.kernel.org List-ID: From: Leo Kim This patch removes the warnings reported by checkpatch.pl for line over 80 characters. And also align comments which is not over 80 but to align with them. Signed-off-by: Leo Kim Signed-off-by: Glen Lee --- drivers/staging/wilc1000/wilc_wlan_if.h | 644 ++++++++++++++++++-------------- 1 file changed, 369 insertions(+), 275 deletions(-) diff --git a/drivers/staging/wilc1000/wilc_wlan_if.h b/drivers/staging/wilc1000/wilc_wlan_if.h index e56014d..0863592 100644 --- a/drivers/staging/wilc1000/wilc_wlan_if.h +++ b/drivers/staging/wilc1000/wilc_wlan_if.h @@ -1,4 +1,4 @@ -/* ////////////////////////////////////////////////////////////////////////// */ +/* ///////////////////////////////////////////////////////////////////////// */ /* */ /* Copyright (c) Atmel Corporation. All rights reserved. */ /* */ @@ -165,7 +165,8 @@ typedef struct { int (*wlan_cfg_set)(int, u32, u8 *, u32, int, u32); int (*wlan_cfg_get)(int, u32, int, u32); int (*wlan_cfg_get_value)(u32, u8 *, u32); - int (*wlan_add_mgmt_to_tx_que)(void *, u8 *, u32, wilc_tx_complete_func_t); + int (*wlan_add_mgmt_to_tx_que)(void *, u8 *, u32, + wilc_tx_complete_func_t); } wilc_wlan_oup_t; /******************************************** @@ -213,16 +214,16 @@ typedef enum { } TX_RATE_T; typedef enum { - B_ONLY_MODE = 0, /* basic rate: 1, 2 Mbps, otherwise: 5, 11 Mbps */ - G_ONLY_MODE, /* basic rate: 6, 12, 24 Mbps, otherwise: 9, 18, 36, 48, 54 Mbps */ - G_MIXED_11B_1_MODE, /* basic rate: 1, 2, 5.5, 11 Mbps, otherwise: all on */ - G_MIXED_11B_2_MODE, /* basic rate: 1, 2, 5, 11, 6, 12, 24 Mbps, otherwise: all on */ + B_ONLY_MODE = 0, /* 1, 2 M, otherwise: 5, 11 M */ + G_ONLY_MODE, /* 6, 12, 24 M, otherwise: 9, 18, 36, 48, 54 M */ + G_MIXED_11B_1_MODE, /* 1, 2, 5.5, 11 M, otherwise: all on */ + G_MIXED_11B_2_MODE, /* 1, 2, 5, 11, 6, 12, 24 M, otherwise: all on */ } G_OPERATING_MODE_T; typedef enum { - G_SHORT_PREAMBLE = 0, /* Short Preamble */ - G_LONG_PREAMBLE = 1, /* Long Preamble */ - G_AUTO_PREAMBLE = 2, /* Auto Preamble Selection */ + G_SHORT_PREAMBLE = 0, /* Short Preamble */ + G_LONG_PREAMBLE = 1, /* Long Preamble */ + G_AUTO_PREAMBLE = 2, /* Auto Preamble Selection */ } G_PREAMBLE_T; #define MAC_CONNECTED 1 @@ -345,10 +346,10 @@ typedef enum { } N_OBSS_DETECTION_T; typedef enum { - RTS_CTS_NONHT_PROT = 0, /* RTS-CTS at non-HT rate */ - FIRST_FRAME_NONHT_PROT, /* First frame at non-HT rate */ - LSIG_TXOP_PROT, /* LSIG TXOP Protection */ - FIRST_FRAME_MIXED_PROT, /* First frame at Mixed format */ + RTS_CTS_NONHT_PROT = 0, /* RTS-CTS at non-HT rate */ + FIRST_FRAME_NONHT_PROT, /* First frame at non-HT rate */ + LSIG_TXOP_PROT, /* LSIG TXOP Protection */ + FIRST_FRAME_MIXED_PROT, /* First frame at Mixed format */ } N_PROTECTION_TYPE_T; typedef enum { @@ -383,237 +384,298 @@ typedef enum { typedef enum { WID_NIL = 0xffff, - /* BSS Type */ - /* -------------------------------------------------------------- */ - /* Configuration : Infrastructure Independent Access Point */ - /* Values to set : 0 1 2 */ - /* -------------------------------------------------------------- */ + /* + * BSS Type + * ----------------------------------------------------------- + * Configuration : Infrastructure Independent Access Point + * Values to set : 0 1 2 + * ----------------------------------------------------------- + */ WID_BSS_TYPE = 0x0000, - /* Transmit Rate */ - /* -------------------------------------------------------------- */ - /* Configuration : 1 2 5.5 11 6 9 12 18 24 36 48 54 */ - /* Values to set : 1 2 5 11 6 9 12 18 24 36 48 54 */ - /* -------------------------------------------------------------- */ + /* + * Transmit Rate + * ----------------------------------------------------------- + * Configuration : 1 2 5.5 11 6 9 12 18 24 36 48 54 + * Values to set : 1 2 5 11 6 9 12 18 24 36 48 54 + * ----------------------------------------------------------- + */ WID_CURRENT_TX_RATE = 0x0001, - /* Channel */ - /* ------------------------------------------------------------------- */ - /* Configuration(g) : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 */ - /* Values to set : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 */ - /* -------------------------------------------------------------------- */ + /* + * Channel + * ----------------------------------------------------------- + * Configuration(g) : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 + * Values to set : 1 2 3 4 5 6 7 8 9 10 11 12 13 14 + * ----------------------------------------------------------- + */ WID_CURRENT_CHANNEL = 0x0002, - /* Preamble */ - /* -------------------------------------------------------------- */ - /* Configuration : short long Auto */ - /* Values to set : 0 1 2 */ - /* -------------------------------------------------------------- */ + /* + * Preamble + * ----------------------------------------------------------- + * Configuration : short long Auto + * Values to set : 0 1 2 + * ----------------------------------------------------------- + */ WID_PREAMBLE = 0x0003, - /* 11g operating mode (ignored if 11g not present) */ - /* -------------------------------------------------------------- */ - /* Configuration : HighPerf Compat(RSet #1) Compat(RSet #2) */ - /* Values to set : 1 2 3 */ - /* -------------------------------------------------------------- */ + /* + * 11g operating mode (ignored if 11g not present) + * ----------------------------------------------------------- + * Configuration : HighPerf Compat(RSet #1) Compat(RSet #2) + * Values to set : 1 2 3 + * ----------------------------------------------------------- + */ WID_11G_OPERATING_MODE = 0x0004, - /* Mac status (response only) */ - /* -------------------------------------------------------------- */ - /* Configuration : disconnect connect */ - /* Values to get : 0 1 */ - /* -------------------------------------------------------------- */ + /* + * Mac status (response only) + * ----------------------------------------------------------- + * Configuration : disconnect connect + * Values to get : 0 1 + * ----------------------------------------------------------- + */ WID_STATUS = 0x0005, - /* Scan type */ - /* -------------------------------------------------------------- */ - /* Configuration : Passive Scanning Active Scanning */ - /* Values to set : 0 1 */ - /* -------------------------------------------------------------- */ + /* + * Scan type + * ----------------------------------------------------------- + * Configuration : Passive Scanning Active Scanning + * Values to set : 0 1 + * ----------------------------------------------------------- + */ WID_SCAN_TYPE = 0x0007, - /* Key Id (WEP default key Id) */ - /* -------------------------------------------------------------- */ - /* Configuration : Any value between 0 to 3 */ - /* Values to set : Same value. Default is 0 */ - /* -------------------------------------------------------------- */ + /* + * Key Id (WEP default key Id) + * ----------------------------------------------------------- + * Configuration : Any value between 0 to 3 + * Values to set : Same value. Default is 0 + * ----------------------------------------------------------- + */ WID_KEY_ID = 0x0009, - /* QoS Enable */ - /* -------------------------------------------------------------- */ - /* Configuration : QoS Disable WMM Enable */ - /* Values to set : 0 1 */ - /* -------------------------------------------------------------- */ + /* + * QoS Enable + * ----------------------------------------------------------- + * Configuration : QoS Disable WMM Enable + * Values to set : 0 1 + * ----------------------------------------------------------- + */ WID_QOS_ENABLE = 0x000A, - /* Power Management */ - /* ------------------------------------------------------------------ */ - /* Configuration : NO_POWERSAVE MIN_POWERSAVE MAX_POWERSAVE */ - /* Values to set : 0 1 2 */ - /* ------------------------------------------------------------------ */ + /* + * Power Management + * ----------------------------------------------------------- + * Configuration : NO_POWERSAVE MIN_POWERSAVE MAX_POWERSAVE + * Values to set : 0 1 2 + * ----------------------------------------------------------- + */ WID_POWER_MANAGEMENT = 0x000B, - /* WEP/802 11I Configuration */ - /* ------------------------------------------------------------------ */ - /* Configuration : Disable WP40 WP104 WPA-AES WPA-TKIP RSN-AES RSN-TKIP */ - /* Values (0x) : 00 03 07 29 49 31 51 */ - /* */ - /* Configuration : WPA-AES+TKIP RSN-AES+TKIP */ - /* Values (0x) : 69 71 */ - /* ------------------------------------------------------------------ */ + /* + * WEP/802 11I Configuration + * ----------------------------------------------------------- + * Configuration:Disable WP40 WP104 WPA-AES WPA-TKIP RSN-AES RSN-TKIP + * Values (0x) : 00 03 07 29 49 31 51 + * Configuration:WPA-AES+TKIP RSN-AES+TKIP + * Values (0x) : 69 71 + * ----------------------------------------------------------- + */ WID_11I_MODE = 0x000C, - /* WEP Configuration: Used in BSS STA mode only when WEP is enabled */ - /* ------------------------------------------------------------------ */ - /* Configuration : Open System Shared Key Any Type | 802.1x Auth */ - /* Values (0x) : 01 02 03 | BIT2 */ - /* ------------------------------------------------------------------ */ + /* + * WEP Configuration: Used in BSS STA mode only when WEP is enabled + * ----------------------------------------------------------- + * Configuration : Open System Shared Key Any Type | 802.1x Auth + * Values (0x) : 01 02 03 | BIT2 + * ----------------------------------------------------------- + */ WID_AUTH_TYPE = 0x000D, - /* Site Survey Type */ - /* -------------------------------------------------------------- */ - /* Configuration : Values to set */ - /* Survey 1 Channel : 0 */ - /* survey all Channels : 1 */ - /* Disable Site Survey : 2 */ - /* -------------------------------------------------------------- */ + /* + * Site Survey Type + * ----------------------------------------------------------- + * Configuration : Values to set + * Survey 1 Channel : 0 + * survey all Channels : 1 + * Disable Site Survey : 2 + * ----------------------------------------------------------- + */ WID_SITE_SURVEY = 0x000E, - /* Listen Interval */ - /* -------------------------------------------------------------- */ - /* Configuration : Any value between 1 to 255 */ - /* Values to set : Same value. Default is 3 */ - /* -------------------------------------------------------------- */ + /* + * Listen Interval + * ----------------------------------------------------------- + * Configuration : Any value between 1 to 255 + * Values to set : Same value. Default is 3 + * ----------------------------------------------------------- + */ WID_LISTEN_INTERVAL = 0x000F, - /* DTIM Period */ - /* -------------------------------------------------------------- */ - /* Configuration : Any value between 1 to 255 */ - /* Values to set : Same value. Default is 3 */ - /* -------------------------------------------------------------- */ + /* + * DTIM Period + * ----------------------------------------------------------- + * Configuration : Any value between 1 to 255 + * Values to set : Same value. Default is 3 + * ----------------------------------------------------------- + */ WID_DTIM_PERIOD = 0x0010, - /* ACK Policy */ - /* -------------------------------------------------------------- */ - /* Configuration : Normal Ack No Ack */ - /* Values to set : 0 1 */ - /* -------------------------------------------------------------- */ + /* + * ACK Policy + * ----------------------------------------------------------- + * Configuration : Normal Ack No Ack + * Values to set : 0 1 + * ----------------------------------------------------------- + */ WID_ACK_POLICY = 0x0011, - /* Reset MAC (Set only) */ - /* -------------------------------------------------------------- */ - /* Configuration : Don't Reset Reset No Request */ - /* Values to set : 0 1 2 */ - /* -------------------------------------------------------------- */ + /* + * Reset MAC (Set only) + * ----------------------------------------------------------- + * Configuration : Don't Reset Reset No Request + * Values to set : 0 1 2 + * ----------------------------------------------------------- + */ WID_RESET = 0x0012, - /* Broadcast SSID Option: Setting this will adhere to "" SSID element */ - /* ------------------------------------------------------------------ */ - /* Configuration : Enable Disable */ - /* Values to set : 1 0 */ - /* ------------------------------------------------------------------ */ + /* + * Broadcast SSID Option: Setting this will adhere to "" SSID element + * ----------------------------------------------------------- + * Configuration : Enable Disable + * Values to set : 1 0 + * ----------------------------------------------------------- + */ WID_BCAST_SSID = 0x0015, - /* Disconnect (Station) */ - /* ------------------------------------------------------------------ */ - /* Configuration : Association ID */ - /* Values to set : Association ID */ - /* ------------------------------------------------------------------ */ + /* + * Disconnect (Station) + * ----------------------------------------------------------- + * Configuration : Association ID + * Values to set : Association ID + * ----------------------------------------------------------- + */ WID_DISCONNECT = 0x0016, - /* 11a Tx Power Level */ - /* -------------------------------------------------------------------- */ - /* Configuration : Sets TX Power (Higher the value greater the power) */ - /* Values to set : Any value between 0 and 63 (inclusive; Default is 48)*/ - /* -------------------------------------------------------------------- */ + /* + * 11a Tx Power Level + * ----------------------------------------------------------- + * Configuration : Sets TX Power (Higher the value greater the power) + * Values to set : Any value between 0 and 63 (inclusive Default 48) + * ----------------------------------------------------------- + */ WID_TX_POWER_LEVEL_11A = 0x0018, - /* Group Key Update Policy Selection */ - /* -------------------------------------------------------------------- */ - /* Configuration : Disabled timeBased packetBased timePacketBased */ - /* Values to set : 1 2 3 4 */ - /* -------------------------------------------------------------------- */ + /* + * Group Key Update Policy Selection + * ----------------------------------------------------------- + * Configuration : Disabled timeBased packetBased timePacketBased + * Values to set : 1 2 3 4 + * ----------------------------------------------------------- + */ WID_REKEY_POLICY = 0x0019, - /* Allow Short Slot */ - /* -------------------------------------------------------------- */ - /* Configuration : Disallow Short Slot Allow Short Slot */ - /* (Enable Only Long Slot) (Enable Short Slot if applicable)*/ - /* Values to set : 0 1 */ - /* -------------------------------------------------------------- */ + /* + * Allow Short Slot + * ----------------------------------------------------------- + * Configuration : Disallow Short Slot Allow Short Slot + * (Enable Only Long Slot) (Enable Short Slot if applicable) + * Values to set : 0 1 + * ----------------------------------------------------------- + */ WID_SHORT_SLOT_ALLOWED = 0x001A, WID_PHY_ACTIVE_REG = 0x001B, - /* 11b Tx Power Level */ - /* -------------------------------------------------------------------- */ - /* Configuration : Sets TX Power (Higher the value greater the power) */ - /* Values to set : Any value between 0 and 63 (inclusive; Default is 48)*/ - /* -------------------------------------------------------------------- */ + /* + * 11b Tx Power Level + * ----------------------------------------------------------- + * Configuration : Sets TX Power (Higher the value greater the power) + * Values to set : Any value between 0 and 63 (inclusive Default 48) + * ----------------------------------------------------------- + */ WID_TX_POWER_LEVEL_11B = 0x001D, - /* Scan Request */ - /* -------------------------------------------------------------------- */ - /* Configuration : Request default scan */ - /* Values to set : 0 */ - /* -------------------------------------------------------------------- */ + /* + * Scan Request + * ----------------------------------------------------------- + * Configuration : Request default scan + * Values to set : 0 + * ----------------------------------------------------------- + */ WID_START_SCAN_REQ = 0x001E, - /* Rssi (get only) */ - /* -------------------------------------------------------------------- */ - /* Configuration : */ - /* Values to get : Rssi value */ - /* -------------------------------------------------------------------- */ + /* + * Rssi (get only) + * ----------------------------------------------------------- + * Configuration : + * Values to get : Rssi value + * ----------------------------------------------------------- + */ WID_RSSI = 0x001F, - /* Join Request */ - /* -------------------------------------------------------------------- */ - /* Configuration : Request to join */ - /* Values to set : index of scan result */ - /* -------------------------------------------------------------------- */ + /* + * Join Request + * ----------------------------------------------------------- + * Configuration : Request to join + * Values to set : index of scan result + * ----------------------------------------------------------- + */ WID_JOIN_REQ = 0x0020, - WID_LINKSPEED = 0x0026, + WID_LINKSPEED = 0x0026, - /* Enable User Control of TX Power */ - /* -------------------------------------------------------------------- */ - /* Configuration : Disable Enable */ - /* Values to set : 0 1 */ - /* -------------------------------------------------------------------- */ + /* + * Enable User Control of TX Power + * ----------------------------------------------------------- + * Configuration : Disable Enable + * Values to set : 0 1 + * ----------------------------------------------------------- + */ WID_USER_CONTROL_ON_TX_POWER = 0x0027, WID_MEMORY_ACCESS_8BIT = 0x0029, - /* Enable Auto RX Sensitivity feature */ - /* -------------------------------------------------------------------- */ - /* Configuration : Disable Enable */ - /* Values to set : 0 1 */ - /* -------------------------------------------------------------------- */ + /* + * Enable Auto RX Sensitivity feature + * ----------------------------------------------------------- + * Configuration : Disable Enable + * Values to set : 0 1 + * ----------------------------------------------------------- + */ WID_AUTO_RX_SENSITIVITY = 0x0032, - /* Receive Buffer Based Ack */ - /* -------------------------------------------------------------------- */ - /* Configuration : Disable Enable */ - /* Values to set : 0 1 */ - /* -------------------------------------------------------------------- */ + /* + * Receive Buffer Based Ack + * ----------------------------------------------------------- + * Configuration : Disable Enable + * Values to set : 0 1 + * ----------------------------------------------------------- + */ WID_DATAFLOW_CONTROL = 0x0033, - /* Scan Filter */ - /* -------------------------------------------------------------------- */ - /* Configuration : Class No filter AP only Station Only */ - /* Values to set : 0 1 2 */ - /* Configuration : Priority High Rssi Low Rssi Detect */ - /* Values to set : 0 0x4 0x08 */ - /* Configuration : Channel filter off filter on */ - /* Values to set : 0 0x10 */ - /* -------------------------------------------------------------------- */ + /* + * Scan Filter + * ----------------------------------------------------------- + * Configuration : Class No filter AP only Station Only + * Values to set : 0 1 2 + * Configuration : Priority High Rssi Low Rssi Detect + * Values to set : 0 0x4 0x0 + * Configuration : Channel filter off filter on + * Values to set : 0 0x10 + * ----------------------------------------------------------- + */ WID_SCAN_FILTER = 0x0036, - /* Link Loss Threshold (measure in the beacon period) */ - /* -------------------------------------------------------------------- */ - /* Configuration : Any value between 10 and 254 (Set to 255 to disable it) */ - /* Values to set : Same value. Default is 10 */ - /* -------------------------------------------------------------------- */ + /* + * Link Loss Threshold (measure in the beacon period) + * ----------------------------------------------------------- + * Configuration : Any value between 10 and 254(Set to 255 disable) + * Values to set : Same value. Default is 10 + * ----------------------------------------------------------- + */ WID_LINK_LOSS_THRESHOLD = 0x0037, WID_ABORT_RUNNING_SCAN = 0x003E, @@ -621,103 +683,127 @@ typedef enum { /* NMAC Character WID list */ WID_WPS_START = 0x0043, - /* Protection mode for MAC */ - /* -------------------------------------------------------------- */ - /* Configuration : Auto No protection ERP HT GF */ - /* Values to set : 0 1 2 3 4 */ - /* -------------------------------------------------------------- */ + /* + * Protection mode for MAC + * ----------------------------------------------------------- + * Configuration : Auto No protection ERP HT GF + * Values to set : 0 1 2 3 4 + * ----------------------------------------------------------- + */ WID_11N_PROT_MECH = 0x0080, - /* ERP Protection type for MAC */ - /* -------------------------------------------------------------- */ - /* Configuration : Self-CTS RTS-CTS */ - /* Values to set : 0 1 */ - /* -------------------------------------------------------------- */ + /* + * ERP Protection type for MAC + * ----------------------------------------------------------- + * Configuration : Self-CTS RTS-CTS + * Values to set : 0 1 + * ----------------------------------------------------------- + */ WID_11N_ERP_PROT_TYPE = 0x0081, - /* HT Option Enable */ - /* -------------------------------------------------------------- */ - /* Configuration : HT Enable HT Disable */ - /* Values to set : 1 0 */ - /* -------------------------------------------------------------- */ + /* + * HT Option Enable + * ----------------------------------------------------------- + * Configuration : HT Enable HT Disable + * Values to set : 1 0 + * ----------------------------------------------------------- + */ WID_11N_ENABLE = 0x0082, - /* 11n Operating mode (Note that 11g operating mode will also be */ - /* used in addition to this, if this is set to HT Mixed mode) */ - /* -------------------------------------------------------------- */ - /* Configuration : HT Mixed HT Only-20MHz HT Only-20/40MHz */ - /* Values to set : 1 2 3 */ - /* -------------------------------------------------------------- */ + /* + * 11n Operating mode (Note that 11g operating mode will also be + * used in addition to this, if this is set to HT Mixed mode) + * ----------------------------------------------------------- + * Configuration : HT Mixed HT Only-20MHz HT Only-20/40MHz + * Values to set : 1 2 3 + * ----------------------------------------------------------- + */ WID_11N_OPERATING_MODE = 0x0083, - /* 11n OBSS non-HT STA Detection flag */ - /* -------------------------------------------------------------- */ - /* Configuration : Do not detect */ - /* Values to set : 0 */ - /* Configuration : Detect, do not protect or report */ - /* Values to set : 1 */ - /* Configuration : Detect, protect and do not report */ - /* Values to set : 2 */ - /* Configuration : Detect, protect and report to other BSS */ - /* Values to set : 3 */ - /* -------------------------------------------------------------- */ + /* + * 11n OBSS non-HT STA Detection flag + * ----------------------------------------------------------- + * Configuration : Do not detect + * Values to set : 0 + * Configuration : Detect, do not protect or report + * Values to set : 1 + * Configuration : Detect, protect and do not report + * Values to set : 2 + * Configuration : Detect, protect and report to other BSS + * Values to set : 3 + * ----------------------------------------------------------- + */ WID_11N_OBSS_NONHT_DETECTION = 0x0084, - /* 11n HT Protection Type */ - /* -------------------------------------------------------------- */ - /* Configuration : RTS-CTS First Frame Exchange at non-HT-rate */ - /* Values to set : 0 1 */ - /* Configuration : LSIG TXOP First Frame Exchange in Mixed Fmt */ - /* Values to set : 2 3 */ - /* -------------------------------------------------------------- */ + /* + * 11n HT Protection Type + * ----------------------------------------------------------- + * Configuration : RTS-CTS First Frame Exchange at non-HT-rate + * Values to set : 0 1 + * Configuration : LSIG TXOP First Frame Exchange in Mixed Fmt + * Values to set : 2 3 + * ----------------------------------------------------------- + */ WID_11N_HT_PROT_TYPE = 0x0085, - /* 11n RIFS Protection Enable Flag */ - /* -------------------------------------------------------------- */ - /* Configuration : Disable Enable */ - /* Values to set : 0 1 */ - /* -------------------------------------------------------------- */ + /* + * 11n RIFS Protection Enable Flag + * ----------------------------------------------------------- + * Configuration : Disable Enable + * Values to set : 0 1 + * ----------------------------------------------------------- + */ WID_11N_RIFS_PROT_ENABLE = 0x0086, - /* SMPS Mode */ - /* -------------------------------------------------------------- */ - /* Configuration : Static Dynamic MIMO (Power Save Disabled) */ - /* Values to set : 1 2 3 */ - /* -------------------------------------------------------------- */ + /* + * SMPS Mode + * ----------------------------------------------------------- + * Configuration : Static Dynamic MIMO (Power Save Disabled) + * Values to set : 1 2 3 + * ----------------------------------------------------------- + */ WID_11N_SMPS_MODE = 0x0087, - /* Current transmit MCS */ - /* -------------------------------------------------------------- */ - /* Configuration : MCS Index for data rate */ - /* Values to set : 0 to 7 */ - /* -------------------------------------------------------------- */ + /* + * Current transmit MCS + * ----------------------------------------------------------- + * Configuration : MCS Index for data rate + * Values to set : 0 to 7 + * ----------------------------------------------------------- + */ WID_11N_CURRENT_TX_MCS = 0x0088, WID_11N_PRINT_STATS = 0x0089, - /* 11n Short GI Enable Flag */ - /* -------------------------------------------------------------- */ - /* Configuration : Disable Enable */ - /* Values to set : 0 1 */ - /* -------------------------------------------------------------- */ + /* + * 11n Short GI Enable Flag + * ----------------------------------------------------------- + * Configuration : Disable Enable + * Values to set : 0 1 + * ----------------------------------------------------------- + */ WID_11N_SHORT_GI_ENABLE = 0x008D, - /* 11n RIFS Enable Flag */ - /* -------------------------------------------------------------- */ - /* Configuration : Disable Enable */ - /* Values to set : 0 1 */ - /* -------------------------------------------------------------- */ + /* + * 11n RIFS Enable Flag + * ----------------------------------------------------------- + * Configuration : Disable Enable + * Values to set : 0 1 + * ----------------------------------------------------------- + */ WID_RIFS_MODE = 0x0094, - /* TX Abort Feature */ - /* -------------------------------------------------------------- */ - /* Configuration : Disable Self CTS Enable Self CTS */ - /* Values to set : 0 1 */ - /* Configuration : Disable TX Abort Enable TX Abort */ - /* Values to set : 2 3 */ - /* Configuration : Enable HW TX Abort Enable SW TX Abort */ - /* Values to set : 4 5 */ - /* -------------------------------------------------------------- */ + /* + * TX Abort Feature + * ----------------------------------------------------------- + * Configuration : Disable Self CTS Enable Self CTS + * Values to set : 0 1 + * Configuration : Disable TX Abort Enable TX Abort + * Values to set : 2 3 + * Configuration : Enable HW TX Abort Enable SW TX Abort + * Values to set : 4 5 + * ----------------------------------------------------------- + */ WID_TX_ABORT_CONFIG = 0x00A1, WID_REG_TSSI_11B_VALUE = 0x00A6, @@ -728,18 +814,22 @@ typedef enum { WID_DSCR_TSSI_11G_VALUE = 0x00AB, WID_DSCR_TSSI_11N_VALUE = 0x00AC, - /* Immediate Block-Ack Support */ - /* -------------------------------------------------------------- */ - /* Configuration : Disable Enable */ - /* Values to set : 0 1 */ - /* -------------------------------------------------------------- */ + /* + * Immediate Block-Ack Support + * ----------------------------------------------------------- + * Configuration : Disable Enable + * Values to set : 0 1 + * ----------------------------------------------------------- + */ WID_11N_IMMEDIATE_BA_ENABLED = 0x00AF, - /* TXOP Disable Flag */ - /* -------------------------------------------------------------- */ - /* Configuration : Disable Enable */ - /* Values to set : 1 0 */ - /* -------------------------------------------------------------- */ + /* + * TXOP Disable Flag + * ----------------------------------------------------------- + * Configuration : Disable Enable + * Values to set : 1 0 + * ----------------------------------------------------------- + */ WID_11N_TXOP_PROT_DISABLE = 0x00B0, WID_TX_POWER_LEVEL_11N = 0x00B1, @@ -752,19 +842,23 @@ typedef enum { WID_DEL_BEACON = 0x00CA, WID_LOGTerminal_Switch = 0x00CD, - /* EMAC Short WID list */ - /* RTS Threshold */ - /* -------------------------------------------------------------- */ - /* Configuration : Any value between 256 to 2347 */ - /* Values to set : Same value. Default is 2347 */ - /* -------------------------------------------------------------- */ + /* EMAC Short WID list */ + /* RTS Threshold */ + /* + * ----------------------------------------------------------- + * Configuration : Any value between 256 to 2347 + * Values to set : Same value. Default is 2347 + * ----------------------------------------------------------- + */ WID_RTS_THRESHOLD = 0x1000, - /* Fragmentation Threshold */ - /* -------------------------------------------------------------- */ - /* Configuration : Any value between 256 to 2346 */ - /* Values to set : Same value. Default is 2346 */ - /* -------------------------------------------------------------- */ + /* + * Fragmentation Threshold + * ----------------------------------------------------------- + * Configuration : Any value between 256 to 2346 + * Values to set : Same value. Default is 2346 + * ----------------------------------------------------------- + */ WID_FRAG_THRESHOLD = 0x1001, WID_SHORT_RETRY_LIMIT = 0x1002, @@ -849,9 +943,9 @@ typedef enum { WID_ASSOC_REQ_INFO = 0x301F, WID_ASSOC_RES_INFO = 0x3020, WID_MANUFACTURER = 0x3026, /*Added for CAPI tool */ - WID_MODEL_NAME = 0x3027, /*Added for CAPI tool */ + WID_MODEL_NAME = 0x3027, /*Added for CAPI tool */ WID_MODEL_NUM = 0x3028, /*Added for CAPI tool */ - WID_DEVICE_NAME = 0x3029, /*Added for CAPI tool */ + WID_DEVICE_NAME = 0x3029, /*Added for CAPI tool */ /* NMAC String WID list */ WID_11N_P_ACTION_REQ = 0x3080, -- 1.9.1