Return-path: Received: from devils.ext.ti.com ([198.47.26.153]:37943 "EHLO devils.ext.ti.com" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1750771AbcDFH3B convert rfc822-to-8bit (ORCPT ); Wed, 6 Apr 2016 03:29:01 -0400 From: "Reizer, Eyal" To: Eyal Reizer , "kvalo@codeaurora.org" , "linux-wireless@vger.kernel.org" , "netdev@vger.kernel.org" , "linux-kernel@vger.kernel.org" Subject: RE: [PATCH] wlcore: spi: add wl18xx support Date: Wed, 6 Apr 2016 07:28:56 +0000 Message-ID: <8665E2433BC68541A24DFFCA87B70F5B360B3C81@DFRE01.ent.ti.com> (sfid-20160406_092942_014641_834C8625) References: <1459343218-24536-1-git-send-email-eyalr@ti.com> In-Reply-To: <1459343218-24536-1-git-send-email-eyalr@ti.com> Content-Type: text/plain; charset="us-ascii" MIME-Version: 1.0 Sender: linux-wireless-owner@vger.kernel.org List-ID: Ping on this patch > -----Original Message----- > From: Eyal Reizer [mailto:eyalreizer@gmail.com] > Sent: Wednesday, March 30, 2016 4:07 PM > To: kvalo@codeaurora.org; linux-wireless@vger.kernel.org; > netdev@vger.kernel.org; linux-kernel@vger.kernel.org > Cc: Reizer, Eyal > Subject: [PATCH] wlcore: spi: add wl18xx support > > Add support for using with both wl12xx and wl18xx. > > - all wilink family needs special init command for entering wspi mode. > extra clock cycles should be sent after the spi init command while the > cs pin is high. > - switch to controling the cs pin from the spi driver for achieveing the > above. > - the selected cs gpio is read from the spi device-tree node using the > cs-gpios field and setup as a gpio. > - See the example below for specifying the cs gpio using the cs-gpios entry > > &spi0 { > status = "okay"; > pinctrl-names = "default"; > pinctrl-0 = <&spi0_pins>; > cs-gpios = <&gpio0 5 0>; > #address-cells = <1>; > #size-cells = <0>; > wlcore: wlcore@0 { > compatible = "ti,wl1835"; > vwlan-supply = <&wlan_en_reg>; > spi-max-frequency = <48000000>; > reg = <0>; /* chip select 0 on spi0, ie spi0.0 */ > interrupt-parent = <&gpio0>; > interrupts = <27 IRQ_TYPE_EDGE_RISING>; > }; > }; > > Signed-off-by: Eyal Reizer > --- > drivers/net/wireless/ti/wlcore/spi.c | 176 > ++++++++++++++++++++++++++++++---- > 1 file changed, 157 insertions(+), 19 deletions(-) > > diff --git a/drivers/net/wireless/ti/wlcore/spi.c > b/drivers/net/wireless/ti/wlcore/spi.c > index 96d9c9d..6c5a369 100644 > --- a/drivers/net/wireless/ti/wlcore/spi.c > +++ b/drivers/net/wireless/ti/wlcore/spi.c > @@ -32,6 +32,7 @@ > #include > #include > #include > +#include > > #include "wlcore.h" > #include "wl12xx_80211.h" > @@ -70,16 +71,30 @@ > #define WSPI_MAX_CHUNK_SIZE 4092 > > /* > - * only support SPI for 12xx - this code should be reworked when 18xx > - * support is introduced > + * wl18xx driver aggregation buffer size is (13 * PAGE_SIZE) compared > + to > + * (4 * PAGE_SIZE) for wl12xx, so use the larger buffer needed for > + wl18xx > */ > -#define SPI_AGGR_BUFFER_SIZE (4 * PAGE_SIZE) > +#define SPI_AGGR_BUFFER_SIZE (13 * PAGE_SIZE) > > /* Maximum number of SPI write chunks */ #define > WSPI_MAX_NUM_OF_CHUNKS \ > ((SPI_AGGR_BUFFER_SIZE / WSPI_MAX_CHUNK_SIZE) + 1) > > > +struct wilink_familiy_data { > + char name[8]; > +}; > + > +const struct wilink_familiy_data *wilink_data; > + > +static const struct wilink_familiy_data wl18xx_data = { > + .name = "wl18xx", > +}; > + > +static const struct wilink_familiy_data wl12xx_data = { > + .name = "wl12xx", > +}; > + > struct wl12xx_spi_glue { > struct device *dev; > struct platform_device *core; > @@ -120,6 +135,8 @@ static void wl12xx_spi_init(struct device *child) > struct spi_transfer t; > struct spi_message m; > u8 *cmd = kzalloc(WSPI_INIT_CMD_LEN, GFP_KERNEL); > + struct spi_device *spi = (struct spi_device *)glue->dev; > + struct spi_master *master = spi->master; > > if (!cmd) { > dev_err(child->parent, > @@ -127,6 +144,15 @@ static void wl12xx_spi_init(struct device *child) > return; > } > > + if (!master->cs_gpios) { > + dev_err(child->parent, > + "spi chip select pin missing in platform data!\n"); > + return; > + } > + > + /* Drive CS line low */ > + gpio_direction_output(master->cs_gpios[0], 0); > + > memset(&t, 0, sizeof(t)); > spi_message_init(&m); > > @@ -163,6 +189,26 @@ static void wl12xx_spi_init(struct device *child) > spi_message_add_tail(&t, &m); > > spi_sync(to_spi_device(glue->dev), &m); > + > + /* Send extra clocks with CS high. this is required by the wilink > + * family in order for successfully enter WSPI mode > + */ > + gpio_direction_output(master->cs_gpios[0], 1); > + > + memset(&m, 0, sizeof(m)); > + spi_message_init(&m); > + > + cmd[0] = 0xff; > + cmd[1] = 0xff; > + cmd[2] = 0xff; > + cmd[3] = 0xff; > + swab32s((u32 *)cmd); > + > + t.tx_buf = cmd; > + t.len = 4; > + spi_message_add_tail(&t, &m); > + spi_sync(to_spi_device(glue->dev), &m); > + > kfree(cmd); > } > > @@ -213,6 +259,16 @@ static int __must_check > wl12xx_spi_raw_read(struct device *child, int addr, > u32 *busy_buf; > u32 *cmd; > u32 chunk_len; > + struct spi_device *spi = (struct spi_device *)glue->dev; > + struct spi_master *master = spi->master; > + > + if (!master->cs_gpios) { > + dev_err(child->parent, > + "spi chip select pin missing in platform data!\n"); > + return -EINVAL; > + } > + /* Drive CS line low */ > + gpio_direction_output(master->cs_gpios[0], 0); > > while (len > 0) { > chunk_len = min_t(size_t, WSPI_MAX_CHUNK_SIZE, len); @@ > -267,25 +323,44 @@ static int __must_check wl12xx_spi_raw_read(struct > device *child, int addr, > len -= chunk_len; > } > > + /* Drive CS line high */ > + gpio_direction_output(master->cs_gpios[0], 1); > return 0; > } > > -static int __must_check wl12xx_spi_raw_write(struct device *child, int addr, > - void *buf, size_t len, bool fixed) > +static int __wl12xx_spi_raw_write(struct device *child, int addr, > + void *buf, size_t len, bool fixed) > { > struct wl12xx_spi_glue *glue = dev_get_drvdata(child->parent); > - /* SPI write buffers - 2 for each chunk */ > - struct spi_transfer t[2 * WSPI_MAX_NUM_OF_CHUNKS]; > + struct spi_transfer *t; > struct spi_message m; > u32 commands[WSPI_MAX_NUM_OF_CHUNKS]; /* 1 command per > chunk */ > u32 *cmd; > u32 chunk_len; > int i; > + struct spi_device *spi = (struct spi_device *)glue->dev; > + struct spi_master *master = spi->master; > + > + if (!master->cs_gpios) { > + dev_err(child->parent, > + "spi chip select pin missing in platform data!\n"); > + return -EINVAL; > + } > + > + /* SPI write buffers - 2 for each chunk */ > + t = kzalloc(sizeof(*t) * 2 * WSPI_MAX_NUM_OF_CHUNKS, > GFP_KERNEL); > + if (!t) { > + dev_err(child->parent, > + "could not allocate spi write buffer\n"); > + return -ENOMEM; > + } > + > + /* Drive CS line low */ > + gpio_direction_output(master->cs_gpios[0], 0); > > WARN_ON(len > SPI_AGGR_BUFFER_SIZE); > > spi_message_init(&m); > - memset(t, 0, sizeof(t)); > > cmd = &commands[0]; > i = 0; > @@ -318,9 +393,29 @@ static int __must_check > wl12xx_spi_raw_write(struct device *child, int addr, > > spi_sync(to_spi_device(glue->dev), &m); > > + /* Drive CS line high */ > + gpio_direction_output(master->cs_gpios[0], 1); > + > + kfree(t); > return 0; > } > > +static int __must_check wl12xx_spi_raw_write(struct device *child, int addr, > + void *buf, size_t len, bool fixed) { > + int ret; > + > + /* The ELP wakeup write may fail the first time due to internal > + * hardware latency. It is safer to send the wakeup command twice to > + * avoid unexpected failures. > + */ > + if (addr == HW_ACCESS_ELP_CTRL_REG) > + ret = __wl12xx_spi_raw_write(child, addr, buf, len, fixed); > + ret = __wl12xx_spi_raw_write(child, addr, buf, len, fixed); > + > + return ret; > +} > + > /** > * wl12xx_spi_set_power - power on/off the wl12xx unit > * @child: wl12xx device handle. > @@ -349,17 +444,38 @@ static int wl12xx_spi_set_power(struct device > *child, bool enable) > return ret; > } > > +/** > + * wl12xx_spi_set_block_size > + * > + * This function is not needed for spi mode, but need to be present. > + * Without it defined the wlcore fallback to use the wrong packet > + * allignment on tx. > + */ > +static void wl12xx_spi_set_block_size(struct device *child, > + unsigned int blksz) > +{ > +} > + > static struct wl1271_if_operations spi_ops = { > .read = wl12xx_spi_raw_read, > .write = wl12xx_spi_raw_write, > .reset = wl12xx_spi_reset, > .init = wl12xx_spi_init, > .power = wl12xx_spi_set_power, > - .set_block_size = NULL, > + .set_block_size = wl12xx_spi_set_block_size, > }; > > static const struct of_device_id wlcore_spi_of_match_table[] = { > - { .compatible = "ti,wl1271" }, > + { .compatible = "ti,wl1271", .data = &wl12xx_data}, > + { .compatible = "ti,wl1273", .data = &wl12xx_data}, > + { .compatible = "ti,wl1281", .data = &wl12xx_data}, > + { .compatible = "ti,wl1283", .data = &wl12xx_data}, > + { .compatible = "ti,wl1801", .data = &wl18xx_data}, > + { .compatible = "ti,wl1805", .data = &wl18xx_data}, > + { .compatible = "ti,wl1807", .data = &wl18xx_data}, > + { .compatible = "ti,wl1831", .data = &wl18xx_data}, > + { .compatible = "ti,wl1835", .data = &wl18xx_data}, > + { .compatible = "ti,wl1837", .data = &wl18xx_data}, > { } > }; > MODULE_DEVICE_TABLE(of, wlcore_spi_of_match_table); @@ -375,18 > +491,24 @@ static int wlcore_probe_of(struct spi_device *spi, struct > wl12xx_spi_glue *glue, > struct wlcore_platdev_data *pdev_data) { > struct device_node *dt_node = spi->dev.of_node; > - int ret; > + const struct of_device_id *of_id; > + > + of_id = of_match_node(wlcore_spi_of_match_table, dt_node); > + if (!of_id) > + return -ENODEV; > + > + wilink_data = of_id->data; > + dev_info(&spi->dev, "selected chip familiy is %s\n", > + wilink_data->name); > > if (of_find_property(dt_node, "clock-xtal", NULL)) > pdev_data->ref_clock_xtal = true; > > - ret = of_property_read_u32(dt_node, "ref-clock-frequency", > - &pdev_data->ref_clock_freq); > - if (IS_ERR_VALUE(ret)) { > - dev_err(glue->dev, > - "can't get reference clock frequency (%d)\n", ret); > - return ret; > - } > + /* optional clock frequency params */ > + of_property_read_u32(dt_node, "ref-clock-frequency", > + &pdev_data->ref_clock_freq); > + of_property_read_u32(dt_node, "tcxo-clock-frequency", > + &pdev_data->tcxo_clock_freq); > > return 0; > } > @@ -397,6 +519,7 @@ static int wl1271_probe(struct spi_device *spi) > struct wlcore_platdev_data pdev_data; > struct resource res[1]; > int ret; > + struct spi_master *master = spi->master; > > memset(&pdev_data, 0x00, sizeof(pdev_data)); > > @@ -410,6 +533,12 @@ static int wl1271_probe(struct spi_device *spi) > > glue->dev = &spi->dev; > > + if (!master->cs_gpios) { > + dev_err(glue->dev, > + "spi chip select pin missing in platform data!\n"); > + return -EINVAL; > + } > + > spi_set_drvdata(spi, glue); > > /* This is the only SPI value that we need to set here, the rest @@ - > 431,15 +560,21 @@ static int wl1271_probe(struct spi_device *spi) > return ret; > } > > + if (gpio_request(master->cs_gpios[0], "spi1-cs0")) > + return -EINVAL; > + > ret = spi_setup(spi); > if (ret < 0) { > dev_err(glue->dev, "spi_setup failed\n"); > + gpio_free(master->cs_gpios[0]); > return ret; > } > > - glue->core = platform_device_alloc("wl12xx", > PLATFORM_DEVID_AUTO); > + glue->core = platform_device_alloc(wilink_data->name, > + PLATFORM_DEVID_AUTO); > if (!glue->core) { > dev_err(glue->dev, "can't allocate platform_device\n"); > + gpio_free(master->cs_gpios[0]); > return -ENOMEM; > } > > @@ -474,14 +609,17 @@ static int wl1271_probe(struct spi_device *spi) > > out_dev_put: > platform_device_put(glue->core); > + gpio_free(master->cs_gpios[0]); > return ret; > } > > static int wl1271_remove(struct spi_device *spi) { > struct wl12xx_spi_glue *glue = spi_get_drvdata(spi); > + struct spi_master *master = spi->master; > > platform_device_unregister(glue->core); > + gpio_free(master->cs_gpios[0]); > > return 0; > } > -- > 1.7.9.5