Received-SPF: pass (google.com: domain of linux-wireless-owner@vger.kernel.org designates 23.128.96.18 as permitted sender) client-ip=23.128.96.18;
From:   greearb@candelatech.com
To:     linux-wireless@vger.kernel.org
Cc:     Ben Greear <greearb@candelatech.com>
Subject: [PATCH 07/11] mt76: mt7915:  Add support for tx-overrides.
Date:   Tue, 20 Jul 2021 11:22:51 -0700
Message-Id: <20210720182256.30536-7-greearb@candelatech.com>
In-Reply-To: <20210720182256.30536-1-greearb@candelatech.com>
References: <20210720182256.30536-1-greearb@candelatech.com>
MIME-Version: 1.0
Content-Transfer-Encoding: 8bit
Precedence: bulk

From: Ben Greear <greearb@candelatech.com>

Allow setting fix rate on transmit without using full testmode
logic.

txpower, dynbw, retry count is not currently supported.
And, probably later need additional logic to not apply this
txo to non-data frames and to smaller frames, to allow
ARP and such to go through while also forcing test data frames
to arbitrary tx-rates (rates which very well may not be
received by peer.)

Signed-off-by: Ben Greear <greearb@candelatech.com>
---
 drivers/net/wireless/mediatek/mt76/mt76.h     |   4 +
 .../wireless/mediatek/mt76/mt7915/debugfs.c   | 223 ++++++++++++++++++
 .../net/wireless/mediatek/mt76/mt7915/mac.c   | 100 ++++++--
 .../wireless/mediatek/mt76/mt7915/mt7915.h    |   2 +
 4 files changed, 303 insertions(+), 26 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt76.h b/drivers/net/wireless/mediatek/mt76/mt76.h
index c7c33d8f984a..b4cafe0a55f8 100644
--- a/drivers/net/wireless/mediatek/mt76/mt76.h
+++ b/drivers/net/wireless/mediatek/mt76/mt76.h
@@ -567,6 +567,7 @@ struct mt76_testmode_ops {
 
 struct mt76_testmode_data {
 	enum mt76_testmode_state state;
+	u8 txo_active; /* tx overrides are active */
 
 	u32 param_set[DIV_ROUND_UP(NUM_MT76_TM_ATTRS, 32)];
 	struct sk_buff *tx_skb;
@@ -581,6 +582,9 @@ struct mt76_testmode_data {
 	u8 tx_rate_ldpc;
 	u8 tx_rate_stbc;
 	u8 tx_ltf;
+	u8 txbw; /* specify TX bandwidth: 0 20Mhz, 1 40Mhz, 2 80Mhz, 3 160Mhz */
+	u8 tx_xmit_count; /* 0 means no-ack, 1 means one transmit, etc */
+	u8 tx_dynbw; /* 0:  dynamic bw disabled, 1: dynamic bw enabled */
 
 	u8 tx_antenna_mask;
 	u8 tx_spe_idx;
diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c b/drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c
index 3c0c667430c5..6a2810006975 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/debugfs.c
@@ -109,6 +109,227 @@ mt7915_fw_debug_get(void *data, u64 *val)
 DEFINE_DEBUGFS_ATTRIBUTE(fops_fw_debug, mt7915_fw_debug_get,
 			 mt7915_fw_debug_set, "%lld\n");
 
+static ssize_t mt7915_read_set_rate_override(struct file *file,
+					     char __user *user_buf,
+					     size_t count, loff_t *ppos)
+{
+	struct mt7915_dev *dev = file->private_data;
+	struct mt7915_sta *msta;
+	struct ieee80211_vif *vif;
+	struct wireless_dev *wdev;
+	struct mt76_wcid *wcid;
+	struct mt7915_vif *mvif;
+	struct mt76_phy *mphy = &dev->mt76.phy;
+	char* buf2;
+	int size=8000;
+	int rv, i, j, sofar;
+	const char buf[] =
+		"This allows specify specif tx rate parameters for all DATA frames on a vdev\n"
+		"To set a value, you specify the dev-name and key-value pairs:\n"
+		"tpc=10 sgi=1 mcs=x nss=x pream=x retries=x dynbw=0|1 bw=x enable=0|1\n"
+		"pream: 0=cck, 1=ofdm, 2=HT, 3=VHT, 4=HE_SU\n"
+		"cck-mcs: 0=1Mbps, 1=2Mbps, 3=5.5Mbps, 3=11Mbps\n"
+		"ofdm-mcs: 0=6Mbps, 1=9Mbps, 2=12Mbps, 3=18Mbps, 4=24Mbps, 5=36Mbps, 6=48Mbps, 7=54Mbps\n"
+		"tpc is not implemented currently, bw is 0-3 for 20-160\n"
+		" For example, wlan0:  echo \"wlan0 tpc=255 sgi=1 mcs=0 nss=1 pream=3 retries=1 dynbw=0 bw=0 active=1\" > ...mt76/set_rate_override\n";
+
+	buf2 = kzalloc(size, GFP_KERNEL);
+	if (buf2 == NULL)
+		return -ENOMEM;
+	strcpy(buf2, buf);
+	sofar = strlen(buf2);
+
+	mutex_lock(&mphy->dev->mutex);
+
+	for (i = 0; i < ARRAY_SIZE(dev->mt76.wcid_mask); i++) {
+		u32 mask = dev->mt76.wcid_mask[i];
+		u32 phy_mask = dev->mt76.wcid_phy_mask[i];
+
+		if (!mask)
+			continue;
+
+		for (j = i * 32; mask; j++, mask >>= 1, phy_mask >>= 1) {
+			struct mt76_testmode_data *td;
+
+			if (!(mask & 1))
+				continue;
+
+			wcid = rcu_dereference(dev->mt76.wcid[j]);
+			if (!wcid)
+				continue;
+
+			msta = container_of(wcid, struct mt7915_sta, wcid);
+
+			if (msta->vif != mvif)
+				continue;
+
+			td = &msta->test;
+			vif = container_of((void *)msta->vif, struct ieee80211_vif, drv_priv);
+
+			wdev = ieee80211_vif_to_wdev(vif);
+
+			if (!wdev)
+				continue;
+
+			sofar += scnprintf(buf2 + sofar, size - sofar,
+					   "vdev %i(%s) active=%d tpc=%d sgi=%d mcs=%d nss=%d pream=%d retries=%d dynbw=%d bw=%d\n",
+					   j, wdev->netdev->name,
+					   td->txo_active, td->tx_power[0], td->tx_rate_sgi, td->tx_rate_idx,
+					   td->tx_rate_nss, td->tx_rate_mode, td->tx_xmit_count, td->tx_dynbw,
+					   td->txbw);
+			if (sofar >= size)
+				break;
+		}
+	}
+
+	mutex_unlock(&mphy->dev->mutex);
+
+	rv = simple_read_from_buffer(user_buf, count, ppos, buf2, sofar);
+	kfree(buf2);
+	return rv;
+}
+
+/* Set the rates for specific types of traffic.
+ */
+static ssize_t mt7915_write_set_rate_override(struct file *file,
+					      const char __user *user_buf,
+					      size_t count, loff_t *ppos)
+{
+	struct mt7915_dev *dev = file->private_data;
+	struct mt7915_sta *msta;
+	struct ieee80211_vif *vif;
+	struct mt76_testmode_data *td = NULL;
+	struct wireless_dev *wdev;
+	struct mt76_wcid *wcid;
+	struct mt76_phy *mphy = &dev->mt76.phy;
+	char buf[180];
+	char tmp[20];
+	char* tok;
+	int ret, i, j;
+	unsigned int vdev_id = 0xFFFF;
+	char* bufptr = buf;
+	long rc;
+	char dev_name_match[IFNAMSIZ + 2];
+
+	memset(buf, 0, sizeof(buf));
+
+	simple_write_to_buffer(buf, sizeof(buf) - 1, ppos, user_buf, count);
+
+	/* make sure that buf is null terminated */
+	buf[sizeof(buf) - 1] = 0;
+
+	/* drop the possible '\n' from the end */
+	if (buf[count - 1] == '\n')
+		buf[count - 1] = 0;
+
+	mutex_lock(&mphy->dev->mutex);
+
+	/* Ignore empty lines, 'echo' appends them sometimes at least. */
+	if (buf[0] == 0) {
+		ret = count;
+		goto exit;
+	}
+
+	/* String starts with vdev name, ie 'wlan0'  Find the proper vif that
+	 * matches the name.
+	 */
+	for (i = 0; i < ARRAY_SIZE(dev->mt76.wcid_mask); i++) {
+		u32 mask = dev->mt76.wcid_mask[i];
+		u32 phy_mask = dev->mt76.wcid_phy_mask[i];
+
+		if (!mask)
+			continue;
+
+		for (j = i * 32; mask; j++, mask >>= 1, phy_mask >>= 1) {
+
+			if (!(mask & 1))
+				continue;
+
+			wcid = rcu_dereference(dev->mt76.wcid[j]);
+			if (!wcid)
+				continue;
+
+			msta = container_of(wcid, struct mt7915_sta, wcid);
+
+			vif = container_of((void *)msta->vif, struct ieee80211_vif, drv_priv);
+
+			wdev = ieee80211_vif_to_wdev(vif);
+
+			if (!wdev)
+				continue;
+
+			snprintf(dev_name_match, sizeof(dev_name_match) - 1, "%s ", wdev->netdev->name);
+
+			if (strncmp(dev_name_match, buf, strlen(dev_name_match)) == 0) {
+				vdev_id = j;
+				td = &msta->test;
+				bufptr = buf + strlen(dev_name_match) - 1;
+				break;
+			}
+		}
+	}
+
+	if (vdev_id == 0xFFFF) {
+		if (strstr(buf, "active=0")) {
+			/* Ignore, we are disabling it anyway */
+			ret = count;
+			goto exit;
+		}
+		else {
+			pr_info("mt7915: set-rate-override, unknown netdev name: %s\n", buf);
+		}
+		ret = -EINVAL;
+		goto exit;
+	}
+
+#define MT7915_PARSE_LTOK(a, b)						\
+	if ((tok = strstr(bufptr, " " #a "="))) {			\
+		char* tspace;						\
+		tok += 1; /* move past initial space */			\
+		strncpy(tmp, tok + strlen(#a "="), sizeof(tmp) - 1);	\
+		tmp[sizeof(tmp) - 1] = 0;				\
+		tspace = strstr(tmp, " ");				\
+		if (tspace) { *tspace = 0; }				\
+		if (kstrtol(tmp, 0, &rc) != 0) {			\
+			pr_info("mt7915: set-rate-override: " #a "= could not be parsed, tmp: %s\n", tmp); \
+		}							\
+		else {							\
+			td->b = rc;					\
+		}							\
+	}
+
+	MT7915_PARSE_LTOK(tpc, tx_power[0]);
+	MT7915_PARSE_LTOK(sgi, tx_rate_sgi);
+	MT7915_PARSE_LTOK(mcs, tx_rate_idx);
+	MT7915_PARSE_LTOK(nss, tx_rate_nss);
+	MT7915_PARSE_LTOK(pream, tx_rate_mode);
+	MT7915_PARSE_LTOK(retries, tx_xmit_count);
+	MT7915_PARSE_LTOK(dynbw, tx_dynbw);
+	MT7915_PARSE_LTOK(bw, txbw);
+	MT7915_PARSE_LTOK(active, txo_active);
+
+	pr_info("mt7915: set-rate-overrides, vdev %i(%s) active=%d tpc=%d sgi=%d mcs=%d nss=%d pream=%d retries=%d dynbw=%d bw=%d\n",
+		vdev_id, dev_name_match,
+		td->txo_active, td->tx_power[0], td->tx_rate_sgi, td->tx_rate_idx,
+		td->tx_rate_nss, td->tx_rate_mode, td->tx_xmit_count, td->tx_dynbw,
+		td->txbw);
+
+	ret = count;
+
+exit:
+	mutex_unlock(&mphy->dev->mutex);
+	return ret;
+}
+
+static const struct file_operations fops_set_rate_override = {
+	.read = mt7915_read_set_rate_override,
+	.write = mt7915_write_set_rate_override,
+	.open = simple_open,
+	.owner = THIS_MODULE,
+	.llseek = default_llseek,
+};
+
+
 static int
 mt7915_txs_for_no_skb_set(void *data, u64 val)
 {
@@ -377,6 +598,8 @@ int mt7915_init_debugfs(struct mt7915_dev *dev)
 	debugfs_create_file("ser_trigger", 0200, dir, dev, &fops_ser_trigger);
 	debugfs_create_devm_seqfile(dev->mt76.dev, "txpower_sku", dir,
 				    mt7915_read_rate_txpower);
+	debugfs_create_file("set_rate_override", 0600, dir,
+			    dev, &fops_set_rate_override);
 
 	return 0;
 }
diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/mac.c b/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
index 80acc07c0180..121a3cd33d70 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/mac.c
@@ -758,21 +758,32 @@ mt7915_mac_fill_rx_vector(struct mt7915_dev *dev, struct sk_buff *skb)
 }
 
 static void
-mt7915_mac_write_txwi_tm(struct mt7915_phy *phy, __le32 *txwi,
+mt7915_mac_write_txwi_tm(struct mt7915_phy *phy, struct mt76_wcid *wcid, __le32 *txwi,
 			 struct sk_buff *skb)
 {
-#ifdef CONFIG_NL80211_TESTMODE
-	struct mt76_testmode_data *td = &phy->mt76->test;
+	struct mt76_testmode_data *td;
 	const struct ieee80211_rate *r;
-	u8 bw, mode, nss = td->tx_rate_nss;
-	u8 rate_idx = td->tx_rate_idx;
+	struct mt7915_sta *msta;
+	u8 bw, mode, nss;
+	u8 rate_idx;
 	u16 rateval = 0;
 	u32 val;
 	bool cck = false;
 	int band;
 
-	if (skb != phy->mt76->test.tx_skb)
-		return;
+	msta = container_of(wcid, struct mt7915_sta, wcid);
+
+	if (msta->test.txo_active) {
+		td = &msta->test;
+	}
+	else {
+		if (skb != phy->mt76->test.tx_skb)
+			return;
+		td = &phy->mt76->test;
+	}
+
+	nss = td->tx_rate_nss;
+	rate_idx = td->tx_rate_idx;
 
 	switch (td->tx_rate_mode) {
 	case MT76_TM_TX_MODE_HT:
@@ -813,20 +824,25 @@ mt7915_mac_write_txwi_tm(struct mt7915_phy *phy, __le32 *txwi,
 		break;
 	}
 
-	switch (phy->mt76->chandef.width) {
-	case NL80211_CHAN_WIDTH_40:
-		bw = 1;
-		break;
-	case NL80211_CHAN_WIDTH_80:
-		bw = 2;
-		break;
-	case NL80211_CHAN_WIDTH_80P80:
-	case NL80211_CHAN_WIDTH_160:
-		bw = 3;
-		break;
-	default:
-		bw = 0;
-		break;
+	if (msta->test.txo_active) {
+		bw = td->txbw;
+	}
+	else {
+		switch (phy->mt76->chandef.width) {
+		case NL80211_CHAN_WIDTH_40:
+			bw = 1;
+			break;
+		case NL80211_CHAN_WIDTH_80:
+			bw = 2;
+			break;
+		case NL80211_CHAN_WIDTH_80P80:
+		case NL80211_CHAN_WIDTH_160:
+			bw = 3;
+			break;
+		default:
+			bw = 0;
+			break;
+		}
 	}
 
 	if (td->tx_rate_stbc && nss == 1) {
@@ -838,17 +854,25 @@ mt7915_mac_write_txwi_tm(struct mt7915_phy *phy, __le32 *txwi,
 		   FIELD_PREP(MT_TX_RATE_MODE, mode) |
 		   FIELD_PREP(MT_TX_RATE_NSS, nss - 1);
 
+	/* TODO:  Support per-skb txpower, p.15 of txpower doc, DW2 29:24. */
 	txwi[2] |= cpu_to_le32(MT_TXD2_FIX_RATE);
 
+	/* Looks like this sets tx attempt to exactly 1.
+	 * TODO:  Use td->tx_xmit_count, if in txo mode.
+	 */
 	le32p_replace_bits(&txwi[3], 1, MT_TXD3_REM_TX_COUNT);
 	if (td->tx_rate_mode < MT76_TM_TX_MODE_HT)
 		txwi[3] |= cpu_to_le32(MT_TXD3_BA_DISABLE);
 
+	/* TODO:  Take tx_dynbw into account in txo mode. */
 	val = MT_TXD6_FIXED_BW |
 	      FIELD_PREP(MT_TXD6_BW, bw) |
 	      FIELD_PREP(MT_TXD6_TX_RATE, rateval) |
 	      FIELD_PREP(MT_TXD6_SGI, td->tx_rate_sgi);
 
+	/* pr_info("mt7915: txo, nss: %d bw: %d mode: %d rate_idx: %d  sgi: %d rateval: 0x%x",
+	           nss, bw, mode, rate_idx, td->tx_rate_sgi, rateval); */
+
 	/* for HE_SU/HE_EXT_SU PPDU
 	 * - 1x, 2x, 4x LTF + 0.8us GI
 	 * - 2x LTF + 1.6us GI, 4x LTF + 3.2us GI
@@ -867,9 +891,27 @@ mt7915_mac_write_txwi_tm(struct mt7915_phy *phy, __le32 *txwi,
 
 	txwi[3] &= ~cpu_to_le32(MT_TXD3_SN_VALID);
 	txwi[6] |= cpu_to_le32(val);
-	txwi[7] |= cpu_to_le32(FIELD_PREP(MT_TXD7_SPE_IDX,
-					  phy->test.spe_idx));
-#endif
+	if (msta->test.txo_active) {
+		/* see mt7915_tm_set_tx_frames */
+		static const u8 spe_idx_map[] = {0, 0, 1, 0, 3, 2, 4, 0,
+						 9, 8, 6, 10, 16, 12, 18, 0};
+		u32 spe_idx;
+		if (td->tx_spe_idx) {
+			spe_idx = td->tx_spe_idx;
+		} else {
+			u8 tx_ant = td->tx_antenna_mask;
+			if (!tx_ant) {
+				/* use antenna mask that matches our nss */
+				tx_ant = GENMASK(nss - 1, 0);
+			}
+			spe_idx = spe_idx_map[tx_ant];
+		}
+		txwi[7] |= cpu_to_le32(FIELD_PREP(MT_TXD7_SPE_IDX, spe_idx));
+	}
+	else {
+		txwi[7] |= cpu_to_le32(FIELD_PREP(MT_TXD7_SPE_IDX,
+						  phy->test.spe_idx));
+	}
 }
 
 static void
@@ -1078,8 +1120,14 @@ void mt7915_mac_write_txwi(struct mt7915_dev *dev, __le32 *txwi,
 		txwi[3] |= cpu_to_le32(MT_TXD3_BA_DISABLE);
 	}
 
-	if (mt76_testmode_enabled(mphy))
-		mt7915_mac_write_txwi_tm(mphy->priv, txwi, skb);
+#ifdef CONFIG_NL80211_TESTMODE
+	{
+		struct mt7915_sta *msta;
+		msta = container_of(wcid, struct mt7915_sta, wcid);
+		if (mt76_testmode_enabled(mphy) || msta->test.txo_active)
+			mt7915_mac_write_txwi_tm(mphy->priv, wcid, txwi, skb);
+	}
+#endif
 }
 
 int mt7915_tx_prepare_skb(struct mt76_dev *mdev, void *txwi_ptr,
diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/mt7915.h b/drivers/net/wireless/mediatek/mt76/mt7915/mt7915.h
index 9e2d547d441c..ba1d0c6e24e7 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/mt7915.h
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/mt7915.h
@@ -95,6 +95,8 @@ struct mt7915_sta {
 	struct mt7915_sta_stats stats;
 
 	struct mt7915_sta_key_conf bip;
+
+	struct mt76_testmode_data test;
 };
 
 struct mt7915_vif {
-- 
2.20.1