From: Yogesh Ashok Powar <[email protected]>
Some of the key differences between SD8897 and older chipsets
are as follows:
a) sdio mpa_rx and mpa_tx ports have been increased from 16 to 32
b) Same is the case with read/write bitmap that one receives from
mpa_reg read
c) aggregation packet count doubled from 8 to 16
d) Most of key reg addresses are changed
e) There is a separate command or control port
f) Now command rx/tx_done have new interrupts
1. 'supports_sdio_new_mode' flag is added to handle (a) and (b).
2. (c) and (d) are taken care of by filling chip specific
information in global structurei (mwifiex_sdio_sd8897).
3. For older chipsets, port 0 was cmd port and port 1->15 were
data port. Therefore we had CTRL_PORT_MASK to differentiate
port type. Now these changes are under 'has_control_mask' flag.
Signed-off-by: Yogesh Ashok Powar <[email protected]>
Signed-off-by: Amitkumar Karwar <[email protected]>
Signed-off-by: Nishant Sarmukadam <[email protected]>
Signed-off-by: Bing Zhao <[email protected]>
Signed-off-by: Frank Huang <[email protected]>
---
v2: fix cmd53 single port address overwriting
drivers/net/wireless/mwifiex/Kconfig | 4 +-
drivers/net/wireless/mwifiex/sdio.c | 267 ++++++++++++++++++++++++++++-------
drivers/net/wireless/mwifiex/sdio.h | 105 +++++++++++++-
3 files changed, 315 insertions(+), 61 deletions(-)
diff --git a/drivers/net/wireless/mwifiex/Kconfig b/drivers/net/wireless/mwifiex/Kconfig
index 4f614aa..f7ff472 100644
--- a/drivers/net/wireless/mwifiex/Kconfig
+++ b/drivers/net/wireless/mwifiex/Kconfig
@@ -3,13 +3,13 @@ config MWIFIEX
depends on CFG80211
---help---
This adds support for wireless adapters based on Marvell
- 802.11n chipsets.
+ 802.11n/ac chipsets.
If you choose to build it as a module, it will be called
mwifiex.
config MWIFIEX_SDIO
- tristate "Marvell WiFi-Ex Driver for SD8786/SD8787/SD8797"
+ tristate "Marvell WiFi-Ex Driver for SD8786/SD8787/SD8797/SD8897"
depends on MWIFIEX && MMC
select FW_LOADER
---help---
diff --git a/drivers/net/wireless/mwifiex/sdio.c b/drivers/net/wireless/mwifiex/sdio.c
index 4b196dc..5ee5ed0 100644
--- a/drivers/net/wireless/mwifiex/sdio.c
+++ b/drivers/net/wireless/mwifiex/sdio.c
@@ -84,6 +84,8 @@ mwifiex_sdio_probe(struct sdio_func *func, const struct sdio_device_id *id)
card->reg = data->reg;
card->max_ports = data->max_ports;
card->mp_agg_pkt_limit = data->mp_agg_pkt_limit;
+ card->supports_sdio_new_mode = data->supports_sdio_new_mode;
+ card->has_control_mask = data->has_control_mask;
}
sdio_claim_host(func);
@@ -260,6 +262,8 @@ static int mwifiex_sdio_resume(struct device *dev)
#define SDIO_DEVICE_ID_MARVELL_8787 (0x9119)
/* Device ID for SD8797 */
#define SDIO_DEVICE_ID_MARVELL_8797 (0x9129)
+/* Device ID for SD8897 */
+#define SDIO_DEVICE_ID_MARVELL_8897 (0x912d)
/* WLAN IDs */
static const struct sdio_device_id mwifiex_ids[] = {
@@ -269,6 +273,8 @@ static const struct sdio_device_id mwifiex_ids[] = {
.driver_data = (unsigned long) &mwifiex_sdio_sd8787},
{SDIO_DEVICE(SDIO_VENDOR_ID_MARVELL, SDIO_DEVICE_ID_MARVELL_8797),
.driver_data = (unsigned long) &mwifiex_sdio_sd8797},
+ {SDIO_DEVICE(SDIO_VENDOR_ID_MARVELL, SDIO_DEVICE_ID_MARVELL_8897),
+ .driver_data = (unsigned long) &mwifiex_sdio_sd8897},
{},
};
@@ -412,7 +418,40 @@ static int mwifiex_pm_wakeup_card_complete(struct mwifiex_adapter *adapter)
}
/*
- * This function initializes the IO ports.
+ * This function is used to initialize IO ports for the
+ * chipsets supporting SDIO new mode eg SD8897.
+ */
+static int mwifiex_init_sdio_new_mode(struct mwifiex_adapter *adapter)
+{
+ u8 reg;
+
+ adapter->ioport = MEM_PORT;
+
+ /* enable sdio new mode */
+ if (mwifiex_read_reg(adapter, CARD_CONFIG_2_1_REG, ®))
+ return -1;
+ if (mwifiex_write_reg(adapter, CARD_CONFIG_2_1_REG,
+ reg | CMD53_NEW_MODE))
+ return -1;
+
+ /* Configure cmd port and enable reading rx length from the register */
+ if (mwifiex_read_reg(adapter, CMD_CONFIG_0, ®))
+ return -1;
+ if (mwifiex_write_reg(adapter, CMD_CONFIG_0, reg | CMD_PORT_RD_LEN_EN))
+ return -1;
+
+ /* Enable Dnld/Upld ready auto reset for cmd port after cmd53 is
+ * completed
+ */
+ if (mwifiex_read_reg(adapter, CMD_CONFIG_1, ®))
+ return -1;
+ if (mwifiex_write_reg(adapter, CMD_CONFIG_1, reg | CMD_PORT_AUTO_EN))
+ return -1;
+
+ return 0;
+}
+
+/* This function initializes the IO ports.
*
* The following operations are performed -
* - Read the IO ports (0, 1 and 2)
@@ -426,6 +465,12 @@ static int mwifiex_init_sdio_ioport(struct mwifiex_adapter *adapter)
adapter->ioport = 0;
+ if (card->supports_sdio_new_mode) {
+ if (mwifiex_init_sdio_new_mode(adapter))
+ return -1;
+ goto cont;
+ }
+
/* Read the IO port */
if (!mwifiex_read_reg(adapter, IO_PORT_0_REG, ®))
adapter->ioport |= (reg & 0xff);
@@ -441,7 +486,7 @@ static int mwifiex_init_sdio_ioport(struct mwifiex_adapter *adapter)
adapter->ioport |= ((reg & 0xff) << 16);
else
return -1;
-
+cont:
pr_debug("info: SDIO FUNC1 IO port: %#x\n", adapter->ioport);
/* Set Host interrupt reset to read to clear */
@@ -504,10 +549,16 @@ static int mwifiex_get_rd_port(struct mwifiex_adapter *adapter, u8 *port)
dev_dbg(adapter->dev, "data: mp_rd_bitmap=0x%08x\n", rd_bitmap);
- if (!(rd_bitmap & (CTRL_PORT_MASK | reg->data_port_mask)))
- return -1;
+ if (card->supports_sdio_new_mode) {
+ if (!(rd_bitmap & reg->data_port_mask))
+ return -1;
+ } else {
+ if (!(rd_bitmap & (CTRL_PORT_MASK | reg->data_port_mask)))
+ return -1;
+ }
- if (card->mp_rd_bitmap & CTRL_PORT_MASK) {
+ if ((card->has_control_mask) &&
+ (card->mp_rd_bitmap & CTRL_PORT_MASK)) {
card->mp_rd_bitmap &= (u32) (~CTRL_PORT_MASK);
*port = CTRL_PORT;
dev_dbg(adapter->dev, "data: port=%d mp_rd_bitmap=0x%08x\n",
@@ -542,24 +593,34 @@ static int mwifiex_get_rd_port(struct mwifiex_adapter *adapter, u8 *port)
static int mwifiex_get_wr_port_data(struct mwifiex_adapter *adapter, u32 *port)
{
struct sdio_mmc_card *card = adapter->card;
+ const struct mwifiex_sdio_card_reg *reg = card->reg;
u32 wr_bitmap = card->mp_wr_bitmap;
dev_dbg(adapter->dev, "data: mp_wr_bitmap=0x%08x\n", wr_bitmap);
- if (!(wr_bitmap & card->mp_data_port_mask))
+ if (card->supports_sdio_new_mode &&
+ !(wr_bitmap & reg->data_port_mask)) {
+ adapter->data_sent = true;
+ return -EBUSY;
+ } else if (!card->supports_sdio_new_mode &&
+ !(wr_bitmap & card->mp_data_port_mask)) {
return -1;
+ }
if (card->mp_wr_bitmap & (1 << card->curr_wr_port)) {
card->mp_wr_bitmap &= (u32) (~(1 << card->curr_wr_port));
*port = card->curr_wr_port;
- if (++card->curr_wr_port == card->mp_end_port)
- card->curr_wr_port = card->reg->start_wr_port;
+ if (((card->supports_sdio_new_mode) &&
+ (++card->curr_wr_port == card->max_ports)) ||
+ ((!card->supports_sdio_new_mode) &&
+ (++card->curr_wr_port == card->mp_end_port)))
+ card->curr_wr_port = reg->start_wr_port;
} else {
adapter->data_sent = true;
return -EBUSY;
}
- if (*port == CTRL_PORT) {
+ if ((card->has_control_mask) && (*port == CTRL_PORT)) {
dev_err(adapter->dev,
"invalid data port=%d cur port=%d mp_wr_bitmap=0x%08x -> 0x%08x\n",
*port, card->curr_wr_port, wr_bitmap,
@@ -904,6 +965,9 @@ static void mwifiex_interrupt_status(struct mwifiex_adapter *adapter)
if (sdio_ireg) {
/*
* DN_LD_HOST_INT_STATUS and/or UP_LD_HOST_INT_STATUS
+ * For SDIO new mode CMD port interrupts
+ * DN_LD_CMD_PORT_HOST_INT_STATUS and/or
+ * UP_LD_CMD_PORT_HOST_INT_STATUS
* Clear the interrupt status register
*/
dev_dbg(adapter->dev, "int: sdio_ireg = %#x\n", sdio_ireg);
@@ -1031,7 +1095,7 @@ static int mwifiex_sdio_card_to_host_mp_aggr(struct mwifiex_adapter *adapter,
u8 *curr_ptr;
u32 rx_len = skb->len;
- if (port == CTRL_PORT) {
+ if ((card->has_control_mask) && (port == CTRL_PORT)) {
/* Read the command Resp without aggr */
dev_dbg(adapter->dev, "info: %s: no aggregation for cmd "
"response\n", __func__);
@@ -1048,7 +1112,10 @@ static int mwifiex_sdio_card_to_host_mp_aggr(struct mwifiex_adapter *adapter,
goto rx_curr_single;
}
- if (card->mp_rd_bitmap & (~((u32) CTRL_PORT_MASK))) {
+ if ((!card->has_control_mask && (card->mp_rd_bitmap &
+ card->reg->data_port_mask)) ||
+ (card->has_control_mask && (card->mp_rd_bitmap &
+ (~((u32) CTRL_PORT_MASK))))) {
/* Some more data RX pending */
dev_dbg(adapter->dev, "info: %s: not last packet\n", __func__);
@@ -1100,8 +1167,25 @@ static int mwifiex_sdio_card_to_host_mp_aggr(struct mwifiex_adapter *adapter,
dev_dbg(adapter->dev, "info: do_rx_aggr: num of packets: %d\n",
card->mpa_rx.pkt_cnt);
- mport = (adapter->ioport | SDIO_MPA_ADDR_BASE |
- (card->mpa_rx.ports << 4)) + card->mpa_rx.start_port;
+ if (card->supports_sdio_new_mode) {
+ int i;
+ u32 port_count;
+
+ for (i = 0, port_count = 0; i < card->max_ports; i++)
+ if (card->mpa_rx.ports & BIT(i))
+ port_count++;
+
+ /* Reading data from "start_port + 0" to "start_port +
+ * port_count -1", so decrease the count by 1
+ */
+ port_count--;
+ mport = (adapter->ioport | SDIO_MPA_ADDR_BASE |
+ (port_count << 8)) + card->mpa_rx.start_port;
+ } else {
+ mport = (adapter->ioport | SDIO_MPA_ADDR_BASE |
+ (card->mpa_rx.ports << 4)) +
+ card->mpa_rx.start_port;
+ }
if (mwifiex_read_data_sync(adapter, card->mpa_rx.buf,
card->mpa_rx.buf_len, mport, 1))
@@ -1200,6 +1284,8 @@ static int mwifiex_process_int_status(struct mwifiex_adapter *adapter)
u32 rx_blocks;
u16 rx_len;
unsigned long flags;
+ u32 bitmap;
+ u8 cr;
spin_lock_irqsave(&adapter->int_lock, flags);
sdio_ireg = adapter->int_status;
@@ -1209,12 +1295,60 @@ static int mwifiex_process_int_status(struct mwifiex_adapter *adapter)
if (!sdio_ireg)
return ret;
+ /* Following interrupt is only for SDIO new mode */
+ if (sdio_ireg & DN_LD_CMD_PORT_HOST_INT_STATUS && adapter->cmd_sent)
+ adapter->cmd_sent = false;
+
+ /* Following interrupt is only for SDIO new mode */
+ if (sdio_ireg & UP_LD_CMD_PORT_HOST_INT_STATUS) {
+ u32 pkt_type;
+
+ /* read the len of control packet */
+ rx_len = card->mp_regs[CMD_RD_LEN_1] << 8;
+ rx_len |= (u16) card->mp_regs[CMD_RD_LEN_0];
+ rx_blocks = DIV_ROUND_UP(rx_len, MWIFIEX_SDIO_BLOCK_SIZE);
+ if (rx_len <= INTF_HEADER_LEN ||
+ (rx_blocks * MWIFIEX_SDIO_BLOCK_SIZE) >
+ MWIFIEX_RX_DATA_BUF_SIZE)
+ return -1;
+ rx_len = (u16) (rx_blocks * MWIFIEX_SDIO_BLOCK_SIZE);
+
+ skb = dev_alloc_skb(rx_len);
+ if (!skb)
+ return -1;
+
+ skb_put(skb, rx_len);
+
+ if (mwifiex_sdio_card_to_host(adapter, &pkt_type, skb->data,
+ skb->len, adapter->ioport |
+ CMD_PORT_SLCT)) {
+ dev_err(adapter->dev,
+ "%s: failed to card_to_host", __func__);
+ dev_kfree_skb_any(skb);
+ goto term_cmd;
+ }
+
+ if ((pkt_type != MWIFIEX_TYPE_CMD) &&
+ (pkt_type != MWIFIEX_TYPE_EVENT))
+ dev_err(adapter->dev,
+ "%s:Received wrong packet on cmd port",
+ __func__);
+
+ mwifiex_decode_rx_packet(adapter, skb, pkt_type);
+ }
+
if (sdio_ireg & DN_LD_HOST_INT_STATUS) {
- card->mp_wr_bitmap =
- ((u32) card->mp_regs[reg->wr_bitmap_u]) << 8;
- card->mp_wr_bitmap |=
- (u32) card->mp_regs[reg->wr_bitmap_l];
- dev_dbg(adapter->dev, "int: DNLD: wr_bitmap=0x%08x\n",
+ bitmap = (u32) card->mp_regs[reg->wr_bitmap_l];
+ bitmap |= ((u32) card->mp_regs[reg->wr_bitmap_u]) << 8;
+ if (card->supports_sdio_new_mode) {
+ bitmap |=
+ ((u32) card->mp_regs[reg->wr_bitmap_1l]) << 16;
+ bitmap |=
+ ((u32) card->mp_regs[reg->wr_bitmap_1u]) << 24;
+ }
+ card->mp_wr_bitmap = bitmap;
+
+ dev_dbg(adapter->dev, "int: DNLD: wr_bitmap=0x%x\n",
card->mp_wr_bitmap);
if (adapter->data_sent &&
(card->mp_wr_bitmap & card->mp_data_port_mask)) {
@@ -1227,7 +1361,7 @@ static int mwifiex_process_int_status(struct mwifiex_adapter *adapter)
/* As firmware will not generate download ready interrupt if the port
updated is command port only, cmd_sent should be done for any SDIO
interrupt. */
- if (adapter->cmd_sent) {
+ if (card->has_control_mask && adapter->cmd_sent) {
/* Check if firmware has attach buffer at command port and
update just that in wr_bit_map. */
card->mp_wr_bitmap |=
@@ -1239,10 +1373,16 @@ static int mwifiex_process_int_status(struct mwifiex_adapter *adapter)
dev_dbg(adapter->dev, "info: cmd_sent=%d data_sent=%d\n",
adapter->cmd_sent, adapter->data_sent);
if (sdio_ireg & UP_LD_HOST_INT_STATUS) {
- card->mp_rd_bitmap =
- ((u32) card->mp_regs[reg->rd_bitmap_u]) << 8;
- card->mp_rd_bitmap |= (u32) card->mp_regs[reg->rd_bitmap_l];
- dev_dbg(adapter->dev, "int: UPLD: rd_bitmap=0x%08x\n",
+ bitmap = (u32) card->mp_regs[reg->rd_bitmap_l];
+ bitmap |= ((u32) card->mp_regs[reg->rd_bitmap_u]) << 8;
+ if (card->supports_sdio_new_mode) {
+ bitmap |=
+ ((u32) card->mp_regs[reg->rd_bitmap_1l]) << 16;
+ bitmap |=
+ ((u32) card->mp_regs[reg->rd_bitmap_1u]) << 24;
+ }
+ card->mp_rd_bitmap = bitmap;
+ dev_dbg(adapter->dev, "int: UPLD: rd_bitmap=0x%x\n",
card->mp_rd_bitmap);
while (true) {
@@ -1285,37 +1425,33 @@ static int mwifiex_process_int_status(struct mwifiex_adapter *adapter)
if (mwifiex_sdio_card_to_host_mp_aggr(adapter, skb,
port)) {
- u8 cr = 0;
-
dev_err(adapter->dev, "card_to_host_mpa failed:"
" int status=%#x\n", sdio_ireg);
- if (mwifiex_read_reg(adapter,
- CONFIGURATION_REG, &cr))
- dev_err(adapter->dev,
- "read CFG reg failed\n");
-
- dev_dbg(adapter->dev,
- "info: CFG reg val = %d\n", cr);
- if (mwifiex_write_reg(adapter,
- CONFIGURATION_REG,
- (cr | 0x04)))
- dev_err(adapter->dev,
- "write CFG reg failed\n");
-
- dev_dbg(adapter->dev, "info: write success\n");
- if (mwifiex_read_reg(adapter,
- CONFIGURATION_REG, &cr))
- dev_err(adapter->dev,
- "read CFG reg failed\n");
-
- dev_dbg(adapter->dev,
- "info: CFG reg val =%x\n", cr);
- return -1;
+ goto term_cmd;
}
}
}
return 0;
+
+term_cmd:
+ /* terminate cmd */
+ if (mwifiex_read_reg(adapter, CONFIGURATION_REG, &cr))
+ dev_err(adapter->dev, "read CFG reg failed\n");
+ else
+ dev_dbg(adapter->dev, "info: CFG reg val = %d\n", cr);
+
+ if (mwifiex_write_reg(adapter, CONFIGURATION_REG, (cr | 0x04)))
+ dev_err(adapter->dev, "write CFG reg failed\n");
+ else
+ dev_dbg(adapter->dev, "info: write success\n");
+
+ if (mwifiex_read_reg(adapter, CONFIGURATION_REG, &cr))
+ dev_err(adapter->dev, "read CFG reg failed\n");
+ else
+ dev_dbg(adapter->dev, "info: CFG reg val =%x\n", cr);
+
+ return -1;
}
/*
@@ -1344,7 +1480,9 @@ static int mwifiex_host_to_card_mp_aggr(struct mwifiex_adapter *adapter,
s32 f_postcopy_cur_buf = 0;
u32 mport;
- if ((!card->mpa_tx.enabled) || (port == CTRL_PORT)) {
+ if (!card->mpa_tx.enabled ||
+ (card->has_control_mask && (port == CTRL_PORT)) ||
+ (card->supports_sdio_new_mode && (port == CMD_PORT_SLCT))) {
dev_dbg(adapter->dev, "info: %s: tx aggregation disabled\n",
__func__);
@@ -1419,8 +1557,26 @@ static int mwifiex_host_to_card_mp_aggr(struct mwifiex_adapter *adapter,
dev_dbg(adapter->dev, "data: %s: send aggr buffer: %d %d\n",
__func__,
card->mpa_tx.start_port, card->mpa_tx.ports);
- mport = (adapter->ioport | SDIO_MPA_ADDR_BASE |
- (card->mpa_tx.ports << 4)) + card->mpa_tx.start_port;
+ if (card->supports_sdio_new_mode) {
+ u32 port_count;
+ int i;
+
+ for (i = 0, port_count = 0; i < card->max_ports; i++)
+ if (card->mpa_tx.ports & BIT(i))
+ port_count++;
+
+ /* Writing data from "start_port + 0" to "start_port +
+ * port_count -1", so decrease the count by 1
+ */
+ port_count--;
+ mport = (adapter->ioport | SDIO_MPA_ADDR_BASE |
+ (port_count << 8)) + card->mpa_tx.start_port;
+ } else {
+ mport = (adapter->ioport | SDIO_MPA_ADDR_BASE |
+ (card->mpa_tx.ports << 4)) +
+ card->mpa_tx.start_port;
+ }
+
ret = mwifiex_write_data_to_card(adapter, card->mpa_tx.buf,
card->mpa_tx.buf_len, mport);
@@ -1493,6 +1649,9 @@ static int mwifiex_sdio_host_to_card(struct mwifiex_adapter *adapter,
pkt_len > MWIFIEX_UPLD_SIZE)
dev_err(adapter->dev, "%s: payload=%p, nb=%d\n",
__func__, payload, pkt_len);
+
+ if (card->supports_sdio_new_mode)
+ port = CMD_PORT_SLCT;
}
/* Transfer data to card */
@@ -1748,8 +1907,11 @@ mwifiex_update_mp_end_port(struct mwifiex_adapter *adapter, u16 port)
card->mp_data_port_mask = reg->data_port_mask;
- for (i = 1; i <= card->max_ports - card->mp_end_port; i++)
- card->mp_data_port_mask &= ~(1 << (card->max_ports - i));
+ if (reg->start_wr_port) {
+ for (i = 1; i <= card->max_ports - card->mp_end_port; i++)
+ card->mp_data_port_mask &=
+ ~(1 << (card->max_ports - i));
+ }
card->curr_wr_port = reg->start_wr_port;
@@ -1857,3 +2019,4 @@ MODULE_LICENSE("GPL v2");
MODULE_FIRMWARE(SD8786_DEFAULT_FW_NAME);
MODULE_FIRMWARE(SD8787_DEFAULT_FW_NAME);
MODULE_FIRMWARE(SD8797_DEFAULT_FW_NAME);
+MODULE_FIRMWARE(SD8897_DEFAULT_FW_NAME);
diff --git a/drivers/net/wireless/mwifiex/sdio.h b/drivers/net/wireless/mwifiex/sdio.h
index 597db37..6d51dfd 100644
--- a/drivers/net/wireless/mwifiex/sdio.h
+++ b/drivers/net/wireless/mwifiex/sdio.h
@@ -32,6 +32,7 @@
#define SD8786_DEFAULT_FW_NAME "mrvl/sd8786_uapsta.bin"
#define SD8787_DEFAULT_FW_NAME "mrvl/sd8787_uapsta.bin"
#define SD8797_DEFAULT_FW_NAME "mrvl/sd8797_uapsta.bin"
+#define SD8897_DEFAULT_FW_NAME "mrvl/sd8897_uapsta.bin"
#define BLOCK_MODE 1
#define BYTE_MODE 0
@@ -46,6 +47,23 @@
#define CTRL_PORT 0
#define CTRL_PORT_MASK 0x0001
+#define CMD_PORT_UPLD_INT_MASK (0x1U<<6)
+#define CMD_PORT_DNLD_INT_MASK (0x1U<<7)
+#define HOST_TERM_CMD53 (0x1U << 2)
+#define REG_PORT 0
+#define MEM_PORT 0x10000
+#define CMD_RD_LEN_0 0xB4
+#define CMD_RD_LEN_1 0xB5
+#define CARD_CONFIG_2_1_REG 0xCD
+#define CMD53_NEW_MODE (0x1U << 0)
+#define CMD_CONFIG_0 0xB8
+#define CMD_PORT_RD_LEN_EN (0x1U << 2)
+#define CMD_CONFIG_1 0xB9
+#define CMD_PORT_AUTO_EN (0x1U << 0)
+#define CMD_PORT_SLCT 0x8000
+#define UP_LD_CMD_PORT_HOST_INT_STATUS (0x40U)
+#define DN_LD_CMD_PORT_HOST_INT_STATUS (0x80U)
+
#define SDIO_MP_TX_AGGR_DEF_BUF_SIZE (8192) /* 8K */
/* Multi port RX aggregation buffer size */
@@ -73,6 +91,7 @@
#define UP_LD_HOST_INT_MASK (0x1U)
/* Host Control Registers : Download host interrupt mask */
#define DN_LD_HOST_INT_MASK (0x2U)
+
/* Disable Host interrupt mask */
#define HOST_INT_DISABLE 0xff
@@ -196,8 +215,12 @@ struct mwifiex_sdio_card_reg {
u8 max_mp_regs;
u8 rd_bitmap_l;
u8 rd_bitmap_u;
+ u8 rd_bitmap_1l;
+ u8 rd_bitmap_1u;
u8 wr_bitmap_l;
u8 wr_bitmap_u;
+ u8 wr_bitmap_1l;
+ u8 wr_bitmap_1u;
u8 rd_len_p0_l;
u8 rd_len_p0_u;
u8 card_misc_cfg_reg;
@@ -211,6 +234,8 @@ struct sdio_mmc_card {
const struct mwifiex_sdio_card_reg *reg;
u8 max_ports;
u8 mp_agg_pkt_limit;
+ bool supports_sdio_new_mode;
+ bool has_control_mask;
u32 mp_rd_bitmap;
u32 mp_wr_bitmap;
@@ -232,6 +257,8 @@ struct mwifiex_sdio_device {
const struct mwifiex_sdio_card_reg *reg;
u8 max_ports;
u8 mp_agg_pkt_limit;
+ bool supports_sdio_new_mode;
+ bool has_control_mask;
};
static const struct mwifiex_sdio_card_reg mwifiex_reg_sd87xx = {
@@ -255,11 +282,39 @@ static const struct mwifiex_sdio_card_reg mwifiex_reg_sd87xx = {
.card_misc_cfg_reg = 0x6c,
};
+static const struct mwifiex_sdio_card_reg mwifiex_reg_sd8897 = {
+ .start_rd_port = 0,
+ .start_wr_port = 0,
+ .base_0_reg = 0x60,
+ .base_1_reg = 0x61,
+ .poll_reg = 0x50,
+ .host_int_enable = UP_LD_HOST_INT_MASK | DN_LD_HOST_INT_MASK |
+ CMD_PORT_UPLD_INT_MASK | CMD_PORT_DNLD_INT_MASK,
+ .status_reg_0 = 0xc0,
+ .status_reg_1 = 0xc1,
+ .sdio_int_mask = 0xff,
+ .data_port_mask = 0xffffffff,
+ .max_mp_regs = 184,
+ .rd_bitmap_l = 0x04,
+ .rd_bitmap_u = 0x05,
+ .rd_bitmap_1l = 0x06,
+ .rd_bitmap_1u = 0x07,
+ .wr_bitmap_l = 0x08,
+ .wr_bitmap_u = 0x09,
+ .wr_bitmap_1l = 0x0a,
+ .wr_bitmap_1u = 0x0b,
+ .rd_len_p0_l = 0x0c,
+ .rd_len_p0_u = 0x0d,
+ .card_misc_cfg_reg = 0xcc,
+};
+
static const struct mwifiex_sdio_device mwifiex_sdio_sd8786 = {
.firmware = SD8786_DEFAULT_FW_NAME,
.reg = &mwifiex_reg_sd87xx,
.max_ports = 16,
.mp_agg_pkt_limit = 8,
+ .supports_sdio_new_mode = false,
+ .has_control_mask = true,
};
static const struct mwifiex_sdio_device mwifiex_sdio_sd8787 = {
@@ -267,6 +322,8 @@ static const struct mwifiex_sdio_device mwifiex_sdio_sd8787 = {
.reg = &mwifiex_reg_sd87xx,
.max_ports = 16,
.mp_agg_pkt_limit = 8,
+ .supports_sdio_new_mode = false,
+ .has_control_mask = true,
};
static const struct mwifiex_sdio_device mwifiex_sdio_sd8797 = {
@@ -274,6 +331,17 @@ static const struct mwifiex_sdio_device mwifiex_sdio_sd8797 = {
.reg = &mwifiex_reg_sd87xx,
.max_ports = 16,
.mp_agg_pkt_limit = 8,
+ .supports_sdio_new_mode = false,
+ .has_control_mask = true,
+};
+
+static const struct mwifiex_sdio_device mwifiex_sdio_sd8897 = {
+ .firmware = SD8897_DEFAULT_FW_NAME,
+ .reg = &mwifiex_reg_sd8897,
+ .max_ports = 32,
+ .mp_agg_pkt_limit = 16,
+ .supports_sdio_new_mode = true,
+ .has_control_mask = false,
};
/*
@@ -302,13 +370,23 @@ mp_rx_aggr_port_limit_reached(struct sdio_mmc_card *card)
u8 tmp;
if (card->curr_rd_port < card->mpa_rx.start_port) {
- tmp = card->mp_agg_pkt_limit;
+ if (card->supports_sdio_new_mode)
+ tmp = card->mp_end_port >> 1;
+ else
+ tmp = card->mp_agg_pkt_limit;
if (((card->max_ports - card->mpa_rx.start_port) +
card->curr_rd_port) >= tmp)
return true;
}
+ if (!card->supports_sdio_new_mode)
+ return false;
+
+ if ((card->curr_rd_port - card->mpa_rx.start_port) >=
+ (card->mp_end_port >> 1))
+ return true;
+
return false;
}
@@ -318,13 +396,23 @@ mp_tx_aggr_port_limit_reached(struct sdio_mmc_card *card)
u16 tmp;
if (card->curr_wr_port < card->mpa_tx.start_port) {
- tmp = card->mp_agg_pkt_limit;
+ if (card->supports_sdio_new_mode)
+ tmp = card->mp_end_port >> 1;
+ else
+ tmp = card->mp_agg_pkt_limit;
if (((card->max_ports - card->mpa_tx.start_port) +
card->curr_wr_port) >= tmp)
return true;
}
+ if (!card->supports_sdio_new_mode)
+ return false;
+
+ if ((card->curr_wr_port - card->mpa_tx.start_port) >=
+ (card->mp_end_port >> 1))
+ return true;
+
return false;
}
@@ -337,11 +425,14 @@ static inline void mp_rx_aggr_setup(struct sdio_mmc_card *card,
if (!card->mpa_rx.pkt_cnt)
card->mpa_rx.start_port = port;
- if (card->mpa_rx.start_port <= port)
- card->mpa_rx.ports |= 1 << (card->mpa_rx.pkt_cnt);
- else
- card->mpa_rx.ports |= 1 << (card->mpa_rx.pkt_cnt + 1);
-
+ if (card->supports_sdio_new_mode) {
+ card->mpa_rx.ports |= (1 << port);
+ } else {
+ if (card->mpa_rx.start_port <= port)
+ card->mpa_rx.ports |= 1 << (card->mpa_rx.pkt_cnt);
+ else
+ card->mpa_rx.ports |= 1 << (card->mpa_rx.pkt_cnt + 1);
+ }
card->mpa_rx.skb_arr[card->mpa_rx.pkt_cnt] = skb;
card->mpa_rx.len_arr[card->mpa_rx.pkt_cnt] = skb->len;
card->mpa_rx.pkt_cnt++;
--
1.8.2.3