Hello, Lorenzo et al.
I'm using MT7612 mini-PCIE cards as both AP in a home server and as a client in
a laptop. The AP works perfectly (after some fixing from your side; thanks for
that!), and so does the client modulo it has issues during system resume.
So, the card is installed in my aging Dell Vostro 3360. The system always
suspends fine, but on resume this can happen occasionally:
===
čen 15 20:21:07 spock kernel: mt76x2e 0000:01:00.0: MCU message 2 (seq 11) timed out
čen 15 20:21:07 spock kernel: mt76x2e 0000:01:00.0: MCU message 30 (seq 12) timed out
čen 15 20:21:07 spock kernel: mt76x2e 0000:01:00.0: MCU message 30 (seq 13) timed out
čen 15 20:21:07 spock kernel: mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
čen 15 20:21:07 spock kernel: mt76x2e 0000:01:00.0: Build: 1
čen 15 20:21:07 spock kernel: mt76x2e 0000:01:00.0: Build Time: 201507311614____
čen 15 20:21:07 spock kernel: mt76x2e 0000:01:00.0: Firmware running!
čen 15 20:21:07 spock kernel: ieee80211 phy0: Hardware restart was requested
čen 15 20:21:08 spock kernel: mt76x2e 0000:01:00.0: MCU message 2 (seq 1) timed out
čen 15 20:21:09 spock kernel: mt76x2e 0000:01:00.0: MCU message 30 (seq 2) timed out
čen 15 20:21:10 spock kernel: mt76x2e 0000:01:00.0: MCU message 30 (seq 3) timed out
čen 15 20:21:10 spock kernel: mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
čen 15 20:21:10 spock kernel: mt76x2e 0000:01:00.0: Build: 1
čen 15 20:21:10 spock kernel: mt76x2e 0000:01:00.0: Build Time: 201507311614____
čen 15 20:21:10 spock kernel: mt76x2e 0000:01:00.0: Firmware running!
čen 15 20:21:10 spock kernel: ieee80211 phy0: Hardware restart was requested
čen 15 20:21:11 spock kernel: mt76x2e 0000:01:00.0: MCU message 31 (seq 5) timed out
čen 15 20:21:12 spock kernel: mt76x2e 0000:01:00.0: MCU message 31 (seq 6) timed out
čen 15 20:21:13 spock kernel: mt76x2e 0000:01:00.0: MCU message 31 (seq 7) timed out
čen 15 20:21:14 spock kernel: mt76x2e 0000:01:00.0: MCU message 31 (seq 8) timed out
čen 15 20:21:15 spock kernel: mt76x2e 0000:01:00.0: MCU message 31 (seq 9) timed out
čen 15 20:21:16 spock kernel: mt76x2e 0000:01:00.0: MCU message 31 (seq 10) timed out
čen 15 20:21:17 spock kernel: mt76x2e 0000:01:00.0: MCU message 31 (seq 11) timed out
čen 15 20:21:17 spock kernel: mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
čen 15 20:21:17 spock kernel: mt76x2e 0000:01:00.0: Build: 1
čen 15 20:21:17 spock kernel: mt76x2e 0000:01:00.0: Build Time: 201507311614____
čen 15 20:21:17 spock kernel: mt76x2e 0000:01:00.0: Firmware running!
čen 15 20:21:17 spock kernel: ieee80211 phy0: Hardware restart was requested
čen 15 20:21:18 spock kernel: ------------[ cut here ]------------
čen 15 20:21:18 spock kernel: WARNING: CPU: 3 PID: 11956 at net/mac80211/util.c:2270 ieee80211_reconfig+0x234/0x1700 [mac80211]
čen 15 20:21:18 spock kernel: Modules linked in: pl2303 md4 nls_utf8 cifs dns_resolver fscache libdes cmac ccm bridge stp llc nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables tun nfnetlink msr nls_iso8859_1 nls_cp437 vfat fat snd_hda_codec_hdmi mt76x2e snd_hda_codec_cirrus snd_hda_codec_generic mt76x2_common mt76x02_lib mt76 snd_hda_intel intel_rapl_msr snd_intel_dspcfg mei_hdcp dell_wmi iTCO_wdt mac80211 iTCO_vendor_support intel_rapl_common sparse_keymap wmi_bmof snd_hda_codec x86_pkg_temp_thermal rtsx_usb_ms intel_powerclamp dell_laptop coretemp ledtrig_audio dell_smbios memstick kvm_intel kvm snd_hda_core dell_wmi_descriptor dcdbas snd_hwdep dell_smm_hwmon cfg80211 snd_pcm irqbypass mousedev intel_cstate psmouse joydev intel_uncore intel_rapl_perf input_leds snd_timer i2c_i801 snd mei_me alx rfkill mei libarc4 lpc_ich mdio soundcore battery wmi evdev mac_hid dell_smo8800 ac tcp_bbr crypto_user ip_tables x_tables xfs dm_thin_pool dm_persistent_data dm_bio_prison dm_bufio libcrc32c
čen 15 20:21:18 spock kernel: crc32c_generic dm_crypt hid_logitech_hidpp hid_logitech_dj hid_generic usbhid hid rtsx_usb_sdmmc mmc_core rtsx_usb dm_mod crct10dif_pclmul crc32_pclmul crc32c_intel raid10 ghash_clmulni_intel serio_raw atkbd libps2 md_mod aesni_intel crypto_simd cryptd glue_helper xhci_pci xhci_hcd ehci_pci ehci_hcd i8042 serio i915 intel_gtt i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops cec rc_core drm agpgart
čen 15 20:21:18 spock kernel: CPU: 3 PID: 11956 Comm: kworker/3:1 Not tainted 5.7.0-pf2 #1
čen 15 20:21:18 spock kernel: Hardware name: Dell Inc. Vostro 3360/0F5DWF, BIOS A18 09/25/2013
čen 15 20:21:18 spock kernel: Workqueue: events_freezable ieee80211_restart_work [mac80211]
čen 15 20:21:18 spock kernel: RIP: 0010:ieee80211_reconfig+0x234/0x1700 [mac80211]
čen 15 20:21:18 spock kernel: Code: 83 b8 0b 00 00 83 e0 fd 83 f8 04 74 e6 48 8b 83 90 04 00 00 a8 01 74 db 48 89 de 48 89 ef e8 03 dc fb ff 41 89 c7 85 c0 74 c9 <0f> 0b 48 8b 5b 08 4c 8b 24 24 48 3b 1c 24 75 12 e9 51 fe ff ff 48
čen 15 20:21:18 spock kernel: RSP: 0018:ffffb803c23ffdf0 EFLAGS: 00010286
čen 15 20:21:18 spock kernel: RAX: 00000000fffffff0 RBX: ffff9595a7564900 RCX: 0000000000000008
čen 15 20:21:18 spock kernel: RDX: 0000000000000000 RSI: 0000000000000100 RDI: 0000000000000100
čen 15 20:21:18 spock kernel: RBP: ffff9595a7ec07e0 R08: 0000000000000000 R09: 0000000000000001
čen 15 20:21:18 spock kernel: R10: 0000000000000001 R11: 0000000000000000 R12: ffff9595a7ec18d0
čen 15 20:21:18 spock kernel: R13: 00000000ffffffff R14: 0000000000000000 R15: 00000000fffffff0
čen 15 20:21:18 spock kernel: FS: 0000000000000000(0000) GS:ffff9595af2c0000(0000) knlGS:0000000000000000
čen 15 20:21:18 spock kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
čen 15 20:21:18 spock kernel: CR2: 000055e56d7de000 CR3: 000000042200a001 CR4: 00000000001706e0
čen 15 20:21:18 spock kernel: Call Trace:
čen 15 20:21:18 spock kernel: ieee80211_restart_work+0xb7/0xe0 [mac80211]
čen 15 20:21:18 spock kernel: process_one_work+0x1d4/0x3c0
čen 15 20:21:18 spock kernel: worker_thread+0x228/0x470
čen 15 20:21:18 spock kernel: ? process_one_work+0x3c0/0x3c0
čen 15 20:21:18 spock kernel: kthread+0x19c/0x1c0
čen 15 20:21:18 spock kernel: ? __kthread_init_worker+0x30/0x30
čen 15 20:21:18 spock kernel: ret_from_fork+0x35/0x40
čen 15 20:21:18 spock kernel: ---[ end trace d8e4d40f48014382 ]---
čen 15 20:21:18 spock kernel: ------------[ cut here ]------------
čen 15 20:21:18 spock kernel: wlp1s0: Failed check-sdata-in-driver check, flags: 0x0
čen 15 20:21:18 spock kernel: WARNING: CPU: 3 PID: 11956 at net/mac80211/driver-ops.h:17 drv_remove_interface+0x11f/0x130 [mac80211]
čen 15 20:21:18 spock kernel: Modules linked in: pl2303 md4 nls_utf8 cifs dns_resolver fscache libdes cmac ccm bridge stp llc nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables tun nfnetlink msr nls_iso8859_1 nls_cp437 vfat fat snd_hda_codec_hdmi mt76x2e snd_hda_codec_cirrus snd_hda_codec_generic mt76x2_common mt76x02_lib mt76 snd_hda_intel intel_rapl_msr snd_intel_dspcfg mei_hdcp dell_wmi iTCO_wdt mac80211 iTCO_vendor_support intel_rapl_common sparse_keymap wmi_bmof snd_hda_codec x86_pkg_temp_thermal rtsx_usb_ms intel_powerclamp dell_laptop coretemp ledtrig_audio dell_smbios memstick kvm_intel kvm snd_hda_core dell_wmi_descriptor dcdbas snd_hwdep dell_smm_hwmon cfg80211 snd_pcm irqbypass mousedev intel_cstate psmouse joydev intel_uncore intel_rapl_perf input_leds snd_timer i2c_i801 snd mei_me alx rfkill mei libarc4 lpc_ich mdio soundcore battery wmi evdev mac_hid dell_smo8800 ac tcp_bbr crypto_user ip_tables x_tables xfs dm_thin_pool dm_persistent_data dm_bio_prison dm_bufio libcrc32c
čen 15 20:21:18 spock kernel: crc32c_generic dm_crypt hid_logitech_hidpp hid_logitech_dj hid_generic usbhid hid rtsx_usb_sdmmc mmc_core rtsx_usb dm_mod crct10dif_pclmul crc32_pclmul crc32c_intel raid10 ghash_clmulni_intel serio_raw atkbd libps2 md_mod aesni_intel crypto_simd cryptd glue_helper xhci_pci xhci_hcd ehci_pci ehci_hcd i8042 serio i915 intel_gtt i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops cec rc_core drm agpgart
čen 15 20:21:18 spock kernel: CPU: 3 PID: 11956 Comm: kworker/3:1 Tainted: G W 5.7.0-pf2 #1
čen 15 20:21:18 spock kernel: Hardware name: Dell Inc. Vostro 3360/0F5DWF, BIOS A18 09/25/2013
čen 15 20:21:18 spock kernel: Workqueue: events_freezable ieee80211_restart_work [mac80211]
čen 15 20:21:18 spock kernel: RIP: 0010:drv_remove_interface+0x11f/0x130 [mac80211]
čen 15 20:21:18 spock kernel: Code: a0 27 d2 da e9 4b ff ff ff 48 8b 86 78 04 00 00 48 8d b6 98 04 00 00 48 c7 c7 e8 1f f7 c0 48 85 c0 48 0f 45 f0 e8 59 fe db da <0f> 0b 5b 5d 41 5c c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00
čen 15 20:21:18 spock kernel: RSP: 0018:ffffb803c23ffc80 EFLAGS: 00010282
čen 15 20:21:18 spock kernel: RAX: 0000000000000000 RBX: ffff9595a7564900 RCX: 0000000000000000
čen 15 20:21:18 spock kernel: RDX: 0000000000000001 RSI: 0000000000000082 RDI: 00000000ffffffff
čen 15 20:21:18 spock kernel: RBP: ffff9595a7ec1930 R08: 00000000000004b6 R09: 0000000000000001
čen 15 20:21:18 spock kernel: R10: 0000000000000001 R11: 0000000000006f08 R12: ffff9595a7ec1000
čen 15 20:21:18 spock kernel: R13: ffff9595a75654b8 R14: ffff9595a7ec0ca0 R15: ffff9595a7ec07e0
čen 15 20:21:18 spock kernel: FS: 0000000000000000(0000) GS:ffff9595af2c0000(0000) knlGS:0000000000000000
čen 15 20:21:18 spock kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
čen 15 20:21:18 spock kernel: CR2: 000055e56d7de000 CR3: 000000042200a001 CR4: 00000000001706e0
čen 15 20:21:18 spock kernel: Call Trace:
čen 15 20:21:18 spock kernel: ieee80211_do_stop+0x5af/0x8c0 [mac80211]
čen 15 20:21:18 spock kernel: ieee80211_stop+0x16/0x20 [mac80211]
čen 15 20:21:18 spock kernel: __dev_close_many+0xaa/0x120
čen 15 20:21:18 spock kernel: dev_close_many+0xa1/0x2b0
čen 15 20:21:18 spock kernel: dev_close+0x6d/0x90
čen 15 20:21:18 spock kernel: cfg80211_shutdown_all_interfaces+0x71/0xd0 [cfg80211]
čen 15 20:21:18 spock kernel: ieee80211_reconfig+0xa2/0x1700 [mac80211]
čen 15 20:21:18 spock kernel: ieee80211_restart_work+0xb7/0xe0 [mac80211]
čen 15 20:21:18 spock kernel: process_one_work+0x1d4/0x3c0
čen 15 20:21:18 spock kernel: worker_thread+0x228/0x470
čen 15 20:21:18 spock kernel: ? process_one_work+0x3c0/0x3c0
čen 15 20:21:18 spock kernel: kthread+0x19c/0x1c0
čen 15 20:21:18 spock kernel: ? __kthread_init_worker+0x30/0x30
čen 15 20:21:18 spock kernel: ret_from_fork+0x35/0x40
čen 15 20:21:18 spock kernel: ---[ end trace d8e4d40f48014383 ]---
===
The Wi-Fi becomes unusable from this point. If I `modprobe -r` the "mt76x2e" module
after this splat, the system hangs completely.
If the system resumes fine, the resume itself takes quite some time (more than
10 seconds).
I've found a workaround for this, though. It seems the system behaves fine if I
do `modprobe -r mt76x2e` before it goes to sleep, and then `modprobe mt76x2e`
after resume. Also, the resume time improves greatly.
I cannot say if it is some regression or not. I've installed the card
just recently, and used it with v5.7 kernel series only.
Do you have any idea what could go wrong and how to approach the issue?
Thanks.
--
Best regards,
Oleksandr Natalenko (post-factum)
Principal Software Maintenance Engineer
> Hello, Lorenzo et al.
Hi Oleksandr,
>
> I'm using MT7612 mini-PCIE cards as both AP in a home server and as a client in
> a laptop. The AP works perfectly (after some fixing from your side; thanks for
> that!), and so does the client modulo it has issues during system resume.
>
[...]
>
> The Wi-Fi becomes unusable from this point. If I `modprobe -r` the "mt76x2e" module
> after this splat, the system hangs completely.
>
> If the system resumes fine, the resume itself takes quite some time (more than
> 10 seconds).
>
> I've found a workaround for this, though. It seems the system behaves fine if I
> do `modprobe -r mt76x2e` before it goes to sleep, and then `modprobe mt76x2e`
> after resume. Also, the resume time improves greatly.
>
> I cannot say if it is some regression or not. I've installed the card
> just recently, and used it with v5.7 kernel series only.
>
> Do you have any idea what could go wrong and how to approach the issue?
I have not reproduced the issue myself yet, but I guess we can try:
1- update to latest Felix's tree [1]
2- could you please try to apply the patch below? (compile-test only)
Regards,
Lorenzo
[1] https://github.com/nbd168/wireless
From 400268a0ee5843cf736308504dfbd2f20a291eaf Mon Sep 17 00:00:00 2001
Message-Id: <400268a0ee5843cf736308504dfbd2f20a291eaf.1592478809.git.lorenzo@kernel.org>
From: Lorenzo Bianconi <[email protected]>
Date: Thu, 18 Jun 2020 13:10:11 +0200
Subject: [PATCH] mt76: mt76x2: fix pci suspend
Signed-off-by: Lorenzo Bianconi <[email protected]>
---
.../net/wireless/mediatek/mt76/mt76x02_dma.h | 1 +
.../net/wireless/mediatek/mt76/mt76x02_mmio.c | 15 +++++
.../net/wireless/mediatek/mt76/mt76x2/pci.c | 58 +++++++++++++++++++
3 files changed, 74 insertions(+)
diff --git a/drivers/net/wireless/mediatek/mt76/mt76x02_dma.h b/drivers/net/wireless/mediatek/mt76/mt76x02_dma.h
index 4aff4f8e87b6..6262f2ecded5 100644
--- a/drivers/net/wireless/mediatek/mt76/mt76x02_dma.h
+++ b/drivers/net/wireless/mediatek/mt76/mt76x02_dma.h
@@ -62,5 +62,6 @@ mt76x02_wait_for_wpdma(struct mt76_dev *dev, int timeout)
int mt76x02_dma_init(struct mt76x02_dev *dev);
void mt76x02_dma_disable(struct mt76x02_dev *dev);
void mt76x02_dma_cleanup(struct mt76x02_dev *dev);
+void mt76x02_dma_reset(struct mt76x02_dev *dev);
#endif /* __MT76x02_DMA_H */
diff --git a/drivers/net/wireless/mediatek/mt76/mt76x02_mmio.c b/drivers/net/wireless/mediatek/mt76/mt76x02_mmio.c
index cbbe986655fe..e2631c964331 100644
--- a/drivers/net/wireless/mediatek/mt76/mt76x02_mmio.c
+++ b/drivers/net/wireless/mediatek/mt76/mt76x02_mmio.c
@@ -348,6 +348,21 @@ void mt76x02_dma_disable(struct mt76x02_dev *dev)
}
EXPORT_SYMBOL_GPL(mt76x02_dma_disable);
+void mt76x02_dma_reset(struct mt76x02_dev *dev)
+{
+ int i;
+
+ mt76x02_dma_disable(dev);
+ usleep_range(1000, 2000);
+
+ for (i = 0; i < __MT_TXQ_MAX; i++)
+ mt76_queue_tx_cleanup(dev, i, true);
+ mt76_for_each_q_rx(&dev->mt76, i)
+ mt76_queue_rx_reset(dev, i);
+
+ mt76x02_dma_enable(dev);
+}
+
void mt76x02_mac_start(struct mt76x02_dev *dev)
{
mt76x02_mac_reset_counters(dev);
diff --git a/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c b/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
index 53ca0cedf026..5543e242fb9b 100644
--- a/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
+++ b/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
@@ -103,6 +103,60 @@ mt76pci_remove(struct pci_dev *pdev)
mt76_free_device(mdev);
}
+static int __maybe_unused
+mt76x2e_suspend(struct pci_dev *pdev, pm_message_t state)
+{
+ struct mt76_dev *mdev = pci_get_drvdata(pdev);
+ struct mt76x02_dev *dev = container_of(mdev, struct mt76x02_dev, mt76);
+ int i, err;
+
+ napi_disable(&mdev->tx_napi);
+ tasklet_kill(&mdev->pre_tbtt_tasklet);
+ tasklet_kill(&mdev->tx_tasklet);
+
+ mt76_for_each_q_rx(mdev, i)
+ napi_disable(&mdev->napi[i]);
+
+ mt76x02_dma_reset(dev);
+
+ pci_enable_wake(pdev, pci_choose_state(pdev, state), true);
+ pci_save_state(pdev);
+ err = pci_set_power_state(pdev, pci_choose_state(pdev, state));
+ if (err)
+ goto restore;
+
+ return 0;
+
+restore:
+ mt76_for_each_q_rx(mdev, i)
+ napi_enable(&mdev->napi[i]);
+ napi_enable(&mdev->tx_napi);
+
+ return err;
+}
+
+static int __maybe_unused
+mt76x2e_resume(struct pci_dev *pdev)
+{
+ struct mt76_dev *mdev = pci_get_drvdata(pdev);
+ int i, err;
+
+ err = pci_set_power_state(pdev, PCI_D0);
+ if (err)
+ return err;
+
+ pci_restore_state(pdev);
+
+ mt76_for_each_q_rx(mdev, i) {
+ napi_enable(&mdev->napi[i]);
+ napi_schedule(&mdev->napi[i]);
+ }
+ napi_enable(&mdev->tx_napi);
+ napi_schedule(&mdev->tx_napi);
+
+ return 0;
+}
+
MODULE_DEVICE_TABLE(pci, mt76pci_device_table);
MODULE_FIRMWARE(MT7662_FIRMWARE);
MODULE_FIRMWARE(MT7662_ROM_PATCH);
@@ -113,6 +167,10 @@ static struct pci_driver mt76pci_driver = {
.id_table = mt76pci_device_table,
.probe = mt76pci_probe,
.remove = mt76pci_remove,
+#ifdef CONFIG_PM
+ .suspend = mt76x2e_suspend,
+ .resume = mt76x2e_resume,
+#endif /* CONFIG_PM */
};
module_pci_driver(mt76pci_driver);
--
2.26.2
>
> Thanks.
>
> --
> Best regards,
> Oleksandr Natalenko (post-factum)
> Principal Software Maintenance Engineer
>
Hello, Lorenzo.
Thanks for the quick reply. Please see my observation below.
On Thu, Jun 18, 2020 at 01:18:59PM +0200, Lorenzo Bianconi wrote:
> I have not reproduced the issue myself yet, but I guess we can try:
> 1- update to latest Felix's tree [1]
> 2- could you please try to apply the patch below? (compile-test only)
I've started with trying your patch first (apllied to v5.7.4). Please
see my comments on it inline.
> [1] https://github.com/nbd168/wireless
>
> From 400268a0ee5843cf736308504dfbd2f20a291eaf Mon Sep 17 00:00:00 2001
> Message-Id: <400268a0ee5843cf736308504dfbd2f20a291eaf.1592478809.git.lorenzo@kernel.org>
> From: Lorenzo Bianconi <[email protected]>
> Date: Thu, 18 Jun 2020 13:10:11 +0200
> Subject: [PATCH] mt76: mt76x2: fix pci suspend
>
> Signed-off-by: Lorenzo Bianconi <[email protected]>
> ---
> .../net/wireless/mediatek/mt76/mt76x02_dma.h | 1 +
> .../net/wireless/mediatek/mt76/mt76x02_mmio.c | 15 +++++
> .../net/wireless/mediatek/mt76/mt76x2/pci.c | 58 +++++++++++++++++++
> 3 files changed, 74 insertions(+)
>
> diff --git a/drivers/net/wireless/mediatek/mt76/mt76x02_dma.h b/drivers/net/wireless/mediatek/mt76/mt76x02_dma.h
> index 4aff4f8e87b6..6262f2ecded5 100644
> --- a/drivers/net/wireless/mediatek/mt76/mt76x02_dma.h
> +++ b/drivers/net/wireless/mediatek/mt76/mt76x02_dma.h
> @@ -62,5 +62,6 @@ mt76x02_wait_for_wpdma(struct mt76_dev *dev, int timeout)
> int mt76x02_dma_init(struct mt76x02_dev *dev);
> void mt76x02_dma_disable(struct mt76x02_dev *dev);
> void mt76x02_dma_cleanup(struct mt76x02_dev *dev);
> +void mt76x02_dma_reset(struct mt76x02_dev *dev);
>
> #endif /* __MT76x02_DMA_H */
> diff --git a/drivers/net/wireless/mediatek/mt76/mt76x02_mmio.c b/drivers/net/wireless/mediatek/mt76/mt76x02_mmio.c
> index cbbe986655fe..e2631c964331 100644
> --- a/drivers/net/wireless/mediatek/mt76/mt76x02_mmio.c
> +++ b/drivers/net/wireless/mediatek/mt76/mt76x02_mmio.c
> @@ -348,6 +348,21 @@ void mt76x02_dma_disable(struct mt76x02_dev *dev)
> }
> EXPORT_SYMBOL_GPL(mt76x02_dma_disable);
>
> +void mt76x02_dma_reset(struct mt76x02_dev *dev)
> +{
> + int i;
> +
> + mt76x02_dma_disable(dev);
> + usleep_range(1000, 2000);
> +
> + for (i = 0; i < __MT_TXQ_MAX; i++)
> + mt76_queue_tx_cleanup(dev, i, true);
> + mt76_for_each_q_rx(&dev->mt76, i)
Since v5.7.4 doesn't have this macro, I've pulled it manually.
> + mt76_queue_rx_reset(dev, i);
> +
> + mt76x02_dma_enable(dev);
> +}
I had to add EXPORT_SYMBOL_GPL(mt76x02_dma_reset) in order to get the
kernel linked successfully.
> +
> void mt76x02_mac_start(struct mt76x02_dev *dev)
> {
> mt76x02_mac_reset_counters(dev);
> diff --git a/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c b/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> index 53ca0cedf026..5543e242fb9b 100644
> --- a/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> +++ b/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> @@ -103,6 +103,60 @@ mt76pci_remove(struct pci_dev *pdev)
> mt76_free_device(mdev);
> }
>
> +static int __maybe_unused
> +mt76x2e_suspend(struct pci_dev *pdev, pm_message_t state)
> +{
> + struct mt76_dev *mdev = pci_get_drvdata(pdev);
> + struct mt76x02_dev *dev = container_of(mdev, struct mt76x02_dev, mt76);
> + int i, err;
> +
> + napi_disable(&mdev->tx_napi);
> + tasklet_kill(&mdev->pre_tbtt_tasklet);
> + tasklet_kill(&mdev->tx_tasklet);
> +
> + mt76_for_each_q_rx(mdev, i)
> + napi_disable(&mdev->napi[i]);
> +
> + mt76x02_dma_reset(dev);
> +
> + pci_enable_wake(pdev, pci_choose_state(pdev, state), true);
> + pci_save_state(pdev);
> + err = pci_set_power_state(pdev, pci_choose_state(pdev, state));
> + if (err)
> + goto restore;
> +
> + return 0;
> +
> +restore:
> + mt76_for_each_q_rx(mdev, i)
> + napi_enable(&mdev->napi[i]);
> + napi_enable(&mdev->tx_napi);
> +
> + return err;
> +}
> +
> +static int __maybe_unused
> +mt76x2e_resume(struct pci_dev *pdev)
> +{
> + struct mt76_dev *mdev = pci_get_drvdata(pdev);
> + int i, err;
> +
> + err = pci_set_power_state(pdev, PCI_D0);
> + if (err)
> + return err;
> +
> + pci_restore_state(pdev);
> +
> + mt76_for_each_q_rx(mdev, i) {
> + napi_enable(&mdev->napi[i]);
> + napi_schedule(&mdev->napi[i]);
> + }
> + napi_enable(&mdev->tx_napi);
> + napi_schedule(&mdev->tx_napi);
> +
> + return 0;
> +}
> +
> MODULE_DEVICE_TABLE(pci, mt76pci_device_table);
> MODULE_FIRMWARE(MT7662_FIRMWARE);
> MODULE_FIRMWARE(MT7662_ROM_PATCH);
> @@ -113,6 +167,10 @@ static struct pci_driver mt76pci_driver = {
> .id_table = mt76pci_device_table,
> .probe = mt76pci_probe,
> .remove = mt76pci_remove,
> +#ifdef CONFIG_PM
> + .suspend = mt76x2e_suspend,
> + .resume = mt76x2e_resume,
> +#endif /* CONFIG_PM */
> };
>
> module_pci_driver(mt76pci_driver);
> --
> 2.26.2
Unfortunately, it seems it did little change to my setup. The resume
time shrunk it seems (but is still noticeable), and the system survived
2 suspend/resume cycles, but after the third resume the following
happened:
===
čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: MCU message 2 (seq 11) timed out
čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: MCU message 30 (seq 12) timed out
čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: MCU message 30 (seq 13) timed out
čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: Build: 1
čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: Build Time: 201507311614____
čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: Firmware running!
čen 18 23:11:58 spock kernel: ieee80211 phy0: Hardware restart was requested
čen 18 23:11:59 spock kernel: mt76x2e 0000:01:00.0: MCU message 2 (seq 1) timed out
čen 18 23:11:59 spock kernel: mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
čen 18 23:11:59 spock kernel: mt76x2e 0000:01:00.0: Build: 1
čen 18 23:11:59 spock kernel: mt76x2e 0000:01:00.0: Build Time: 201507311614____
čen 18 23:11:59 spock kernel: mt76x2e 0000:01:00.0: Firmware running!
čen 18 23:11:59 spock kernel: ieee80211 phy0: Hardware restart was requested
čen 18 23:12:00 spock kernel: mt76x2e 0000:01:00.0: MCU message 30 (seq 3) timed out
čen 18 23:12:01 spock kernel: mt76x2e 0000:01:00.0: MCU message 30 (seq 4) timed out
čen 18 23:12:01 spock kernel: mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
čen 18 23:12:01 spock kernel: mt76x2e 0000:01:00.0: Build: 1
čen 18 23:12:01 spock kernel: mt76x2e 0000:01:00.0: Build Time: 201507311614____
čen 18 23:12:01 spock kernel: mt76x2e 0000:01:00.0: Firmware running!
čen 18 23:12:01 spock kernel: ieee80211 phy0: Hardware restart was requested
čen 18 23:12:02 spock kernel: ------------[ cut here ]------------
čen 18 23:12:02 spock kernel: WARNING: CPU: 3 PID: 171 at net/mac80211/util.c:2270 ieee80211_reconfig+0x234/0x1700 [mac80211]
čen 18 23:12:02 spock kernel: Modules linked in: cmac ccm bridge stp llc nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables msr tun nfnetlink nls_iso8859_1 nls_cp437 vfat fat mt76x2e mt76x2_common mt76x02_lib mt76 mac80211 intel_rapl_msr snd_hda_codec_hdmi snd_hda_codec_cirrus mei_hdcp snd_hda_codec_generic cfg80211 intel_rapl_common x86_pkg_temp_thermal intel_powerclamp coretemp dell_laptop iTCO_wdt snd_hda_intel kvm_intel iTCO_vendor_support dell_wmi snd_intel_dspcfg sparse_keymap snd_hda_codec ledtrig_audio wmi_bmof dell_smbios snd_hda_core kvm rtsx_usb_ms dell_wmi_descriptor memstick dcdbas snd_hwdep dell_smm_hwmon irqbypass psmouse intel_cstate snd_pcm intel_uncore joydev intel_rapl_perf mousedev mei_me alx rfkill input_leds snd_timer i2c_i801 snd mei lpc_ich libarc4 mdio soundcore battery wmi evdev dell_smo8800 mac_hid ac tcp_bbr crypto_user ip_tables x_tables xfs dm_thin_pool dm_persistent_data dm_bio_prison dm_bufio libcrc32c crc32c_generic dm_crypt hid_logitech_hidpp hid_logitech_dj
čen 18 23:12:02 spock kernel: hid_generic usbhid hid rtsx_usb_sdmmc mmc_core rtsx_usb dm_mod raid10 serio_raw atkbd libps2 md_mod crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel crypto_simd cryptd glue_helper xhci_pci xhci_hcd ehci_pci ehci_hcd i8042 serio i915 intel_gtt i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops cec rc_core drm agpgart
čen 18 23:12:02 spock kernel: CPU: 3 PID: 171 Comm: kworker/3:3 Not tainted 5.7.0-pf3 #1
čen 18 23:12:02 spock kernel: Hardware name: Dell Inc. Vostro 3360/0F5DWF, BIOS A18 09/25/2013
čen 18 23:12:02 spock kernel: Workqueue: events_freezable ieee80211_restart_work [mac80211]
čen 18 23:12:02 spock kernel: RIP: 0010:ieee80211_reconfig+0x234/0x1700 [mac80211]
čen 18 23:12:02 spock kernel: Code: 83 b8 0b 00 00 83 e0 fd 83 f8 04 74 e6 48 8b 83 90 04 00 00 a8 01 74 db 48 89 de 48 89 ef e8 03 dc fb ff 41 89 c7 85 c0 74 c9 <0f> 0b 48 8b 5b 08 4c 8b 24 24 48 3b 1c 24 75 12 e9 51 fe ff ff 48
čen 18 23:12:02 spock kernel: RSP: 0018:ffffa87c40403df0 EFLAGS: 00010286
čen 18 23:12:02 spock kernel: RAX: 00000000fffffff0 RBX: ffff9fe028f6e900 RCX: 0000000000000008
čen 18 23:12:02 spock kernel: RDX: 0000000000000000 RSI: 0000000000000100 RDI: 0000000000000100
čen 18 23:12:02 spock kernel: RBP: ffff9fe0283787e0 R08: 0000000000000000 R09: 0000000000000001
čen 18 23:12:02 spock kernel: R10: 0000000000000001 R11: 0000000000000000 R12: ffff9fe0283798d0
čen 18 23:12:02 spock kernel: R13: 00000000ffffffff R14: 0000000000000000 R15: 00000000fffffff0
čen 18 23:12:02 spock kernel: FS: 0000000000000000(0000) GS:ffff9fe02f2c0000(0000) knlGS:0000000000000000
čen 18 23:12:02 spock kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
čen 18 23:12:02 spock kernel: CR2: 00007f313b33a940 CR3: 000000012ea0a002 CR4: 00000000001706e0
čen 18 23:12:02 spock kernel: Call Trace:
čen 18 23:12:02 spock kernel: ieee80211_restart_work+0xb7/0xe0 [mac80211]
čen 18 23:12:02 spock kernel: process_one_work+0x1d4/0x3c0
čen 18 23:12:02 spock kernel: worker_thread+0x228/0x470
čen 18 23:12:02 spock kernel: ? process_one_work+0x3c0/0x3c0
čen 18 23:12:02 spock kernel: kthread+0x19c/0x1c0
čen 18 23:12:02 spock kernel: ? __kthread_init_worker+0x30/0x30
čen 18 23:12:02 spock kernel: ret_from_fork+0x35/0x40
čen 18 23:12:02 spock kernel: ---[ end trace e017bc3573bd9bf2 ]---
čen 18 23:12:02 spock kernel: ------------[ cut here ]------------
čen 18 23:12:02 spock kernel: wlp1s0: Failed check-sdata-in-driver check, flags: 0x0
čen 18 23:12:02 spock kernel: WARNING: CPU: 3 PID: 171 at net/mac80211/driver-ops.h:17 drv_remove_interface+0x11f/0x130 [mac80211]
čen 18 23:12:02 spock kernel: Modules linked in: cmac ccm bridge stp llc nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables msr tun nfnetlink nls_iso8859_1 nls_cp437 vfat fat mt76x2e mt76x2_common mt76x02_lib mt76 mac80211 intel_rapl_msr snd_hda_codec_hdmi snd_hda_codec_cirrus mei_hdcp snd_hda_codec_generic cfg80211 intel_rapl_common x86_pkg_temp_thermal intel_powerclamp coretemp dell_laptop iTCO_wdt snd_hda_intel kvm_intel iTCO_vendor_support dell_wmi snd_intel_dspcfg sparse_keymap snd_hda_codec ledtrig_audio wmi_bmof dell_smbios snd_hda_core kvm rtsx_usb_ms dell_wmi_descriptor memstick dcdbas snd_hwdep dell_smm_hwmon irqbypass psmouse intel_cstate snd_pcm intel_uncore joydev intel_rapl_perf mousedev mei_me alx rfkill input_leds snd_timer i2c_i801 snd mei lpc_ich libarc4 mdio soundcore battery wmi evdev dell_smo8800 mac_hid ac tcp_bbr crypto_user ip_tables x_tables xfs dm_thin_pool dm_persistent_data dm_bio_prison dm_bufio libcrc32c crc32c_generic dm_crypt hid_logitech_hidpp hid_logitech_dj
čen 18 23:12:02 spock kernel: hid_generic usbhid hid rtsx_usb_sdmmc mmc_core rtsx_usb dm_mod raid10 serio_raw atkbd libps2 md_mod crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel crypto_simd cryptd glue_helper xhci_pci xhci_hcd ehci_pci ehci_hcd i8042 serio i915 intel_gtt i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops cec rc_core drm agpgart
čen 18 23:12:02 spock kernel: CPU: 3 PID: 171 Comm: kworker/3:3 Tainted: G W 5.7.0-pf3 #1
čen 18 23:12:02 spock kernel: Hardware name: Dell Inc. Vostro 3360/0F5DWF, BIOS A18 09/25/2013
čen 18 23:12:02 spock kernel: Workqueue: events_freezable ieee80211_restart_work [mac80211]
čen 18 23:12:02 spock kernel: RIP: 0010:drv_remove_interface+0x11f/0x130 [mac80211]
čen 18 23:12:02 spock kernel: Code: a0 57 f0 c2 e9 4b ff ff ff 48 8b 86 78 04 00 00 48 8d b6 98 04 00 00 48 c7 c7 e8 ef f8 c0 48 85 c0 48 0f 45 f0 e8 99 2e fa c2 <0f> 0b 5b 5d 41 5c c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00
čen 18 23:12:02 spock kernel: RSP: 0018:ffffa87c40403c80 EFLAGS: 00010282
čen 18 23:12:02 spock kernel: RAX: 0000000000000000 RBX: ffff9fe028f6e900 RCX: 0000000000000000
čen 18 23:12:02 spock kernel: RDX: 0000000000000001 RSI: 0000000000000082 RDI: 00000000ffffffff
čen 18 23:12:02 spock kernel: RBP: ffff9fe028379930 R08: 00000000000004c9 R09: 0000000000000001
čen 18 23:12:02 spock kernel: R10: 0000000000000001 R11: 0000000000006fc0 R12: ffff9fe028379000
čen 18 23:12:02 spock kernel: R13: ffff9fe028f6f4b8 R14: ffff9fe028378ca0 R15: ffff9fe0283787e0
čen 18 23:12:02 spock kernel: FS: 0000000000000000(0000) GS:ffff9fe02f2c0000(0000) knlGS:0000000000000000
čen 18 23:12:02 spock kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
čen 18 23:12:02 spock kernel: CR2: 00007f313b33a940 CR3: 000000012ea0a002 CR4: 00000000001706e0
čen 18 23:12:02 spock kernel: Call Trace:
čen 18 23:12:02 spock kernel: ieee80211_do_stop+0x5af/0x8c0 [mac80211]
čen 18 23:12:02 spock kernel: ieee80211_stop+0x16/0x20 [mac80211]
čen 18 23:12:02 spock kernel: __dev_close_many+0xaa/0x120
čen 18 23:12:02 spock kernel: dev_close_many+0xa1/0x2b0
čen 18 23:12:02 spock kernel: dev_close+0x6d/0x90
čen 18 23:12:02 spock kernel: cfg80211_shutdown_all_interfaces+0x71/0xd0 [cfg80211]
čen 18 23:12:02 spock kernel: ieee80211_reconfig+0xa2/0x1700 [mac80211]
čen 18 23:12:02 spock kernel: ieee80211_restart_work+0xb7/0xe0 [mac80211]
čen 18 23:12:02 spock kernel: process_one_work+0x1d4/0x3c0
čen 18 23:12:02 spock kernel: worker_thread+0x228/0x470
čen 18 23:12:02 spock kernel: ? process_one_work+0x3c0/0x3c0
čen 18 23:12:02 spock kernel: kthread+0x19c/0x1c0
čen 18 23:12:02 spock kernel: ? __kthread_init_worker+0x30/0x30
čen 18 23:12:02 spock kernel: ret_from_fork+0x35/0x40
čen 18 23:12:02 spock kernel: ---[ end trace e017bc3573bd9bf3 ]---
===
Do you still want me to try Felix's tree, or there's something else I
can try?
Thank you.
--
Best regards,
Oleksandr Natalenko (post-factum)
Principal Software Maintenance Engineer
Hi Lorenzo,
I love your patch! Yet something to improve:
[auto build test ERROR on wireless-drivers-next/master]
[also build test ERROR on v5.8-rc1 next-20200618]
[If your patch is applied to the wrong git tree, kindly drop us a note.
And when submitting patch, we suggest to use as documented in
https://git-scm.com/docs/git-format-patch]
url: https://github.com/0day-ci/linux/commits/Lorenzo-Bianconi/mt76-mt76x2-fix-pci-suspend/20200618-192056
base: https://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next.git master
config: x86_64-randconfig-a013-20200619 (attached as .config)
compiler: gcc-9 (Debian 9.3.0-13) 9.3.0
reproduce (this is a W=1 build):
# save the attached .config to linux build tree
make W=1 ARCH=x86_64
If you fix the issue, kindly add following tag as appropriate
Reported-by: kernel test robot <[email protected]>
All errors (new ones prefixed by >>, old ones prefixed by <<):
>> ERROR: modpost: "mt76x02_dma_reset" [drivers/net/wireless/mediatek/mt76/mt76x2/mt76x2e.ko] undefined!
---
0-DAY CI Kernel Test Service, Intel Corporation
https://lists.01.org/hyperkitty/list/[email protected]
> Hello, Lorenzo.
Hi Oleksandr,
>
> Thanks for the quick reply. Please see my observation below.
>
> On Thu, Jun 18, 2020 at 01:18:59PM +0200, Lorenzo Bianconi wrote:
> > I have not reproduced the issue myself yet, but I guess we can try:
> > 1- update to latest Felix's tree [1]
> > 2- could you please try to apply the patch below? (compile-test only)
>
> I've started with trying your patch first (apllied to v5.7.4). Please
> see my comments on it inline.
>
> > [1] https://github.com/nbd168/wireless
> >
> > From 400268a0ee5843cf736308504dfbd2f20a291eaf Mon Sep 17 00:00:00 2001
> > Message-Id: <400268a0ee5843cf736308504dfbd2f20a291eaf.1592478809.git.lorenzo@kernel.org>
> > From: Lorenzo Bianconi <[email protected]>
> > Date: Thu, 18 Jun 2020 13:10:11 +0200
> > Subject: [PATCH] mt76: mt76x2: fix pci suspend
> >
> > Signed-off-by: Lorenzo Bianconi <[email protected]>
> > ---
[...]
> > + for (i = 0; i < __MT_TXQ_MAX; i++)
> > + mt76_queue_tx_cleanup(dev, i, true);
> > + mt76_for_each_q_rx(&dev->mt76, i)
>
> Since v5.7.4 doesn't have this macro, I've pulled it manually.
this is why I asked to use Felix's tree :)
>
> > + mt76_queue_rx_reset(dev, i);
> > +
> > + mt76x02_dma_enable(dev);
> > +}
>
> I had to add EXPORT_SYMBOL_GPL(mt76x02_dma_reset) in order to get the
> kernel linked successfully.
ack, sorry
>
> > +
> > void mt76x02_mac_start(struct mt76x02_dev *dev)
> > {
> > mt76x02_mac_reset_counters(dev);
> > diff --git a/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c b/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> > index 53ca0cedf026..5543e242fb9b 100644
> > --- a/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> > +++ b/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> > @@ -103,6 +103,60 @@ mt76pci_remove(struct pci_dev *pdev)
> > mt76_free_device(mdev);
> > }
> >
> > +static int __maybe_unused
> > +mt76x2e_suspend(struct pci_dev *pdev, pm_message_t state)
> > +{
> > + struct mt76_dev *mdev = pci_get_drvdata(pdev);
> > + struct mt76x02_dev *dev = container_of(mdev, struct mt76x02_dev, mt76);
> > + int i, err;
can you please double-check what is the PCI state requested during suspend?
Regards,
Lorenzo
> > +
> > + napi_disable(&mdev->tx_napi);
> > + tasklet_kill(&mdev->pre_tbtt_tasklet);
> > + tasklet_kill(&mdev->tx_tasklet);
> > +
> > + mt76_for_each_q_rx(mdev, i)
> > + napi_disable(&mdev->napi[i]);
> > +
> > + mt76x02_dma_reset(dev);
> > +
> > + pci_enable_wake(pdev, pci_choose_state(pdev, state), true);
> > + pci_save_state(pdev);
> > + err = pci_set_power_state(pdev, pci_choose_state(pdev, state));
> > + if (err)
> > + goto restore;
> > +
> > + return 0;
> > +
> > +restore:
> > + mt76_for_each_q_rx(mdev, i)
> > + napi_enable(&mdev->napi[i]);
> > + napi_enable(&mdev->tx_napi);
> > +
> > + return err;
> > +}
> > +
> > +static int __maybe_unused
> > +mt76x2e_resume(struct pci_dev *pdev)
> > +{
> > + struct mt76_dev *mdev = pci_get_drvdata(pdev);
> > + int i, err;
> > +
> > + err = pci_set_power_state(pdev, PCI_D0);
> > + if (err)
> > + return err;
> > +
> > + pci_restore_state(pdev);
> > +
> > + mt76_for_each_q_rx(mdev, i) {
> > + napi_enable(&mdev->napi[i]);
> > + napi_schedule(&mdev->napi[i]);
> > + }
> > + napi_enable(&mdev->tx_napi);
> > + napi_schedule(&mdev->tx_napi);
> > +
> > + return 0;
> > +}
> > +
> > MODULE_DEVICE_TABLE(pci, mt76pci_device_table);
> > MODULE_FIRMWARE(MT7662_FIRMWARE);
> > MODULE_FIRMWARE(MT7662_ROM_PATCH);
> > @@ -113,6 +167,10 @@ static struct pci_driver mt76pci_driver = {
> > .id_table = mt76pci_device_table,
> > .probe = mt76pci_probe,
> > .remove = mt76pci_remove,
> > +#ifdef CONFIG_PM
> > + .suspend = mt76x2e_suspend,
> > + .resume = mt76x2e_resume,
> > +#endif /* CONFIG_PM */
> > };
> >
> > module_pci_driver(mt76pci_driver);
> > --
> > 2.26.2
>
> Unfortunately, it seems it did little change to my setup. The resume
> time shrunk it seems (but is still noticeable), and the system survived
> 2 suspend/resume cycles, but after the third resume the following
> happened:
>
> ===
> čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: MCU message 2 (seq 11) timed out
> čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: MCU message 30 (seq 12) timed out
> čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: MCU message 30 (seq 13) timed out
> čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
> čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: Build: 1
> čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: Build Time: 201507311614____
> čen 18 23:11:58 spock kernel: mt76x2e 0000:01:00.0: Firmware running!
> čen 18 23:11:58 spock kernel: ieee80211 phy0: Hardware restart was requested
> čen 18 23:11:59 spock kernel: mt76x2e 0000:01:00.0: MCU message 2 (seq 1) timed out
> čen 18 23:11:59 spock kernel: mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
> čen 18 23:11:59 spock kernel: mt76x2e 0000:01:00.0: Build: 1
> čen 18 23:11:59 spock kernel: mt76x2e 0000:01:00.0: Build Time: 201507311614____
> čen 18 23:11:59 spock kernel: mt76x2e 0000:01:00.0: Firmware running!
> čen 18 23:11:59 spock kernel: ieee80211 phy0: Hardware restart was requested
> čen 18 23:12:00 spock kernel: mt76x2e 0000:01:00.0: MCU message 30 (seq 3) timed out
> čen 18 23:12:01 spock kernel: mt76x2e 0000:01:00.0: MCU message 30 (seq 4) timed out
> čen 18 23:12:01 spock kernel: mt76x2e 0000:01:00.0: Firmware Version: 0.0.00
> čen 18 23:12:01 spock kernel: mt76x2e 0000:01:00.0: Build: 1
> čen 18 23:12:01 spock kernel: mt76x2e 0000:01:00.0: Build Time: 201507311614____
> čen 18 23:12:01 spock kernel: mt76x2e 0000:01:00.0: Firmware running!
> čen 18 23:12:01 spock kernel: ieee80211 phy0: Hardware restart was requested
> čen 18 23:12:02 spock kernel: ------------[ cut here ]------------
> čen 18 23:12:02 spock kernel: WARNING: CPU: 3 PID: 171 at net/mac80211/util.c:2270 ieee80211_reconfig+0x234/0x1700 [mac80211]
> čen 18 23:12:02 spock kernel: Modules linked in: cmac ccm bridge stp llc nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables msr tun nfnetlink nls_iso8859_1 nls_cp437 vfat fat mt76x2e mt76x2_common mt76x02_lib mt76 mac80211 intel_rapl_msr snd_hda_codec_hdmi snd_hda_codec_cirrus mei_hdcp snd_hda_codec_generic cfg80211 intel_rapl_common x86_pkg_temp_thermal intel_powerclamp coretemp dell_laptop iTCO_wdt snd_hda_intel kvm_intel iTCO_vendor_support dell_wmi snd_intel_dspcfg sparse_keymap snd_hda_codec ledtrig_audio wmi_bmof dell_smbios snd_hda_core kvm rtsx_usb_ms dell_wmi_descriptor memstick dcdbas snd_hwdep dell_smm_hwmon irqbypass psmouse intel_cstate snd_pcm intel_uncore joydev intel_rapl_perf mousedev mei_me alx rfkill input_leds snd_timer i2c_i801 snd mei lpc_ich libarc4 mdio soundcore battery wmi evdev dell_smo8800 mac_hid ac tcp_bbr crypto_user ip_tables x_tables xfs dm_thin_pool dm_persistent_data dm_bio_prison dm_bufio libcrc32c crc32c_generic dm_crypt hid_logitech_hidpp hid_logitech_dj
> čen 18 23:12:02 spock kernel: hid_generic usbhid hid rtsx_usb_sdmmc mmc_core rtsx_usb dm_mod raid10 serio_raw atkbd libps2 md_mod crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel crypto_simd cryptd glue_helper xhci_pci xhci_hcd ehci_pci ehci_hcd i8042 serio i915 intel_gtt i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops cec rc_core drm agpgart
> čen 18 23:12:02 spock kernel: CPU: 3 PID: 171 Comm: kworker/3:3 Not tainted 5.7.0-pf3 #1
> čen 18 23:12:02 spock kernel: Hardware name: Dell Inc. Vostro 3360/0F5DWF, BIOS A18 09/25/2013
> čen 18 23:12:02 spock kernel: Workqueue: events_freezable ieee80211_restart_work [mac80211]
> čen 18 23:12:02 spock kernel: RIP: 0010:ieee80211_reconfig+0x234/0x1700 [mac80211]
> čen 18 23:12:02 spock kernel: Code: 83 b8 0b 00 00 83 e0 fd 83 f8 04 74 e6 48 8b 83 90 04 00 00 a8 01 74 db 48 89 de 48 89 ef e8 03 dc fb ff 41 89 c7 85 c0 74 c9 <0f> 0b 48 8b 5b 08 4c 8b 24 24 48 3b 1c 24 75 12 e9 51 fe ff ff 48
> čen 18 23:12:02 spock kernel: RSP: 0018:ffffa87c40403df0 EFLAGS: 00010286
> čen 18 23:12:02 spock kernel: RAX: 00000000fffffff0 RBX: ffff9fe028f6e900 RCX: 0000000000000008
> čen 18 23:12:02 spock kernel: RDX: 0000000000000000 RSI: 0000000000000100 RDI: 0000000000000100
> čen 18 23:12:02 spock kernel: RBP: ffff9fe0283787e0 R08: 0000000000000000 R09: 0000000000000001
> čen 18 23:12:02 spock kernel: R10: 0000000000000001 R11: 0000000000000000 R12: ffff9fe0283798d0
> čen 18 23:12:02 spock kernel: R13: 00000000ffffffff R14: 0000000000000000 R15: 00000000fffffff0
> čen 18 23:12:02 spock kernel: FS: 0000000000000000(0000) GS:ffff9fe02f2c0000(0000) knlGS:0000000000000000
> čen 18 23:12:02 spock kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> čen 18 23:12:02 spock kernel: CR2: 00007f313b33a940 CR3: 000000012ea0a002 CR4: 00000000001706e0
> čen 18 23:12:02 spock kernel: Call Trace:
> čen 18 23:12:02 spock kernel: ieee80211_restart_work+0xb7/0xe0 [mac80211]
> čen 18 23:12:02 spock kernel: process_one_work+0x1d4/0x3c0
> čen 18 23:12:02 spock kernel: worker_thread+0x228/0x470
> čen 18 23:12:02 spock kernel: ? process_one_work+0x3c0/0x3c0
> čen 18 23:12:02 spock kernel: kthread+0x19c/0x1c0
> čen 18 23:12:02 spock kernel: ? __kthread_init_worker+0x30/0x30
> čen 18 23:12:02 spock kernel: ret_from_fork+0x35/0x40
> čen 18 23:12:02 spock kernel: ---[ end trace e017bc3573bd9bf2 ]---
> čen 18 23:12:02 spock kernel: ------------[ cut here ]------------
> čen 18 23:12:02 spock kernel: wlp1s0: Failed check-sdata-in-driver check, flags: 0x0
> čen 18 23:12:02 spock kernel: WARNING: CPU: 3 PID: 171 at net/mac80211/driver-ops.h:17 drv_remove_interface+0x11f/0x130 [mac80211]
> čen 18 23:12:02 spock kernel: Modules linked in: cmac ccm bridge stp llc nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables msr tun nfnetlink nls_iso8859_1 nls_cp437 vfat fat mt76x2e mt76x2_common mt76x02_lib mt76 mac80211 intel_rapl_msr snd_hda_codec_hdmi snd_hda_codec_cirrus mei_hdcp snd_hda_codec_generic cfg80211 intel_rapl_common x86_pkg_temp_thermal intel_powerclamp coretemp dell_laptop iTCO_wdt snd_hda_intel kvm_intel iTCO_vendor_support dell_wmi snd_intel_dspcfg sparse_keymap snd_hda_codec ledtrig_audio wmi_bmof dell_smbios snd_hda_core kvm rtsx_usb_ms dell_wmi_descriptor memstick dcdbas snd_hwdep dell_smm_hwmon irqbypass psmouse intel_cstate snd_pcm intel_uncore joydev intel_rapl_perf mousedev mei_me alx rfkill input_leds snd_timer i2c_i801 snd mei lpc_ich libarc4 mdio soundcore battery wmi evdev dell_smo8800 mac_hid ac tcp_bbr crypto_user ip_tables x_tables xfs dm_thin_pool dm_persistent_data dm_bio_prison dm_bufio libcrc32c crc32c_generic dm_crypt hid_logitech_hidpp hid_logitech_dj
> čen 18 23:12:02 spock kernel: hid_generic usbhid hid rtsx_usb_sdmmc mmc_core rtsx_usb dm_mod raid10 serio_raw atkbd libps2 md_mod crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel crypto_simd cryptd glue_helper xhci_pci xhci_hcd ehci_pci ehci_hcd i8042 serio i915 intel_gtt i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops cec rc_core drm agpgart
> čen 18 23:12:02 spock kernel: CPU: 3 PID: 171 Comm: kworker/3:3 Tainted: G W 5.7.0-pf3 #1
> čen 18 23:12:02 spock kernel: Hardware name: Dell Inc. Vostro 3360/0F5DWF, BIOS A18 09/25/2013
> čen 18 23:12:02 spock kernel: Workqueue: events_freezable ieee80211_restart_work [mac80211]
> čen 18 23:12:02 spock kernel: RIP: 0010:drv_remove_interface+0x11f/0x130 [mac80211]
> čen 18 23:12:02 spock kernel: Code: a0 57 f0 c2 e9 4b ff ff ff 48 8b 86 78 04 00 00 48 8d b6 98 04 00 00 48 c7 c7 e8 ef f8 c0 48 85 c0 48 0f 45 f0 e8 99 2e fa c2 <0f> 0b 5b 5d 41 5c c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00
> čen 18 23:12:02 spock kernel: RSP: 0018:ffffa87c40403c80 EFLAGS: 00010282
> čen 18 23:12:02 spock kernel: RAX: 0000000000000000 RBX: ffff9fe028f6e900 RCX: 0000000000000000
> čen 18 23:12:02 spock kernel: RDX: 0000000000000001 RSI: 0000000000000082 RDI: 00000000ffffffff
> čen 18 23:12:02 spock kernel: RBP: ffff9fe028379930 R08: 00000000000004c9 R09: 0000000000000001
> čen 18 23:12:02 spock kernel: R10: 0000000000000001 R11: 0000000000006fc0 R12: ffff9fe028379000
> čen 18 23:12:02 spock kernel: R13: ffff9fe028f6f4b8 R14: ffff9fe028378ca0 R15: ffff9fe0283787e0
> čen 18 23:12:02 spock kernel: FS: 0000000000000000(0000) GS:ffff9fe02f2c0000(0000) knlGS:0000000000000000
> čen 18 23:12:02 spock kernel: CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
> čen 18 23:12:02 spock kernel: CR2: 00007f313b33a940 CR3: 000000012ea0a002 CR4: 00000000001706e0
> čen 18 23:12:02 spock kernel: Call Trace:
> čen 18 23:12:02 spock kernel: ieee80211_do_stop+0x5af/0x8c0 [mac80211]
> čen 18 23:12:02 spock kernel: ieee80211_stop+0x16/0x20 [mac80211]
> čen 18 23:12:02 spock kernel: __dev_close_many+0xaa/0x120
> čen 18 23:12:02 spock kernel: dev_close_many+0xa1/0x2b0
> čen 18 23:12:02 spock kernel: dev_close+0x6d/0x90
> čen 18 23:12:02 spock kernel: cfg80211_shutdown_all_interfaces+0x71/0xd0 [cfg80211]
> čen 18 23:12:02 spock kernel: ieee80211_reconfig+0xa2/0x1700 [mac80211]
> čen 18 23:12:02 spock kernel: ieee80211_restart_work+0xb7/0xe0 [mac80211]
> čen 18 23:12:02 spock kernel: process_one_work+0x1d4/0x3c0
> čen 18 23:12:02 spock kernel: worker_thread+0x228/0x470
> čen 18 23:12:02 spock kernel: ? process_one_work+0x3c0/0x3c0
> čen 18 23:12:02 spock kernel: kthread+0x19c/0x1c0
> čen 18 23:12:02 spock kernel: ? __kthread_init_worker+0x30/0x30
> čen 18 23:12:02 spock kernel: ret_from_fork+0x35/0x40
> čen 18 23:12:02 spock kernel: ---[ end trace e017bc3573bd9bf3 ]---
> ===
>
> Do you still want me to try Felix's tree, or there's something else I
> can try?
>
> Thank you.
>
> --
> Best regards,
> Oleksandr Natalenko (post-factum)
> Principal Software Maintenance Engineer
>
Hello, Lorenzo.
On Sun, Jun 21, 2020 at 10:54 PM Lorenzo Bianconi <[email protected]> wrote:
> > > +static int __maybe_unused
> > > +mt76x2e_suspend(struct pci_dev *pdev, pm_message_t state)
> > > +{
> > > + struct mt76_dev *mdev = pci_get_drvdata(pdev);
> > > + struct mt76x02_dev *dev = container_of(mdev, struct mt76x02_dev, mt76);
> > > + int i, err;
>
> can you please double-check what is the PCI state requested during suspend?
Do you mean ACPI S3 (this is the state the system enters)? If not,
what should I check and where?
Thanks.
--
Best regards,
Oleksandr Natalenko (post-factum)
Principal Software Maintenance Engineer
> Hello, Lorenzo.
>
> On Sun, Jun 21, 2020 at 10:54 PM Lorenzo Bianconi <[email protected]> wrote:
> > > > +static int __maybe_unused
> > > > +mt76x2e_suspend(struct pci_dev *pdev, pm_message_t state)
> > > > +{
> > > > + struct mt76_dev *mdev = pci_get_drvdata(pdev);
> > > > + struct mt76x02_dev *dev = container_of(mdev, struct mt76x02_dev, mt76);
> > > > + int i, err;
> >
> > can you please double-check what is the PCI state requested during suspend?
>
> Do you mean ACPI S3 (this is the state the system enters)? If not,
> what should I check and where?
yes, right. Just for debugging, can you please force the card in PCI_D0 during the
suspend?
Regards,
Lorenzo
>
> Thanks.
>
> --
> Best regards,
> Oleksandr Natalenko (post-factum)
> Principal Software Maintenance Engineer
>
On Mon, Jun 22, 2020 at 4:53 PM Lorenzo Bianconi
<[email protected]> wrote:
> > On Sun, Jun 21, 2020 at 10:54 PM Lorenzo Bianconi <[email protected]> wrote:
> > > > > +static int __maybe_unused
> > > > > +mt76x2e_suspend(struct pci_dev *pdev, pm_message_t state)
> > > > > +{
> > > > > + struct mt76_dev *mdev = pci_get_drvdata(pdev);
> > > > > + struct mt76x02_dev *dev = container_of(mdev, struct mt76x02_dev, mt76);
> > > > > + int i, err;
> > >
> > > can you please double-check what is the PCI state requested during suspend?
> >
> > Do you mean ACPI S3 (this is the state the system enters)? If not,
> > what should I check and where?
>
> yes, right. Just for debugging, can you please force the card in PCI_D0 during the
> suspend?
Do you want me to do this:
diff --git a/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
b/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
index 5543e242fb9b..e558342cce03 100644
--- a/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
+++ b/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
@@ -119,9 +119,8 @@ mt76x2e_suspend(struct pci_dev *pdev, pm_message_t state)
mt76x02_dma_reset(dev);
- pci_enable_wake(pdev, pci_choose_state(pdev, state), true);
pci_save_state(pdev);
- err = pci_set_power_state(pdev, pci_choose_state(pdev, state));
+ err = pci_set_power_state(pdev, PCI_D0);
if (err)
goto restore;
?
--
Best regards,
Oleksandr Natalenko (post-factum)
Principal Software Maintenance Engineer
> On Mon, Jun 22, 2020 at 4:53 PM Lorenzo Bianconi
> <[email protected]> wrote:
> > > On Sun, Jun 21, 2020 at 10:54 PM Lorenzo Bianconi <[email protected]> wrote:
> > > > > > +static int __maybe_unused
> > > > > > +mt76x2e_suspend(struct pci_dev *pdev, pm_message_t state)
> > > > > > +{
> > > > > > + struct mt76_dev *mdev = pci_get_drvdata(pdev);
> > > > > > + struct mt76x02_dev *dev = container_of(mdev, struct mt76x02_dev, mt76);
> > > > > > + int i, err;
> > > >
> > > > can you please double-check what is the PCI state requested during suspend?
> > >
> > > Do you mean ACPI S3 (this is the state the system enters)? If not,
> > > what should I check and where?
> >
> > yes, right. Just for debugging, can you please force the card in PCI_D0 during the
> > suspend?
>
> Do you want me to do this:
>
> diff --git a/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> b/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> index 5543e242fb9b..e558342cce03 100644
> --- a/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> +++ b/drivers/net/wireless/mediatek/mt76/mt76x2/pci.c
> @@ -119,9 +119,8 @@ mt76x2e_suspend(struct pci_dev *pdev, pm_message_t state)
>
> mt76x02_dma_reset(dev);
>
> - pci_enable_wake(pdev, pci_choose_state(pdev, state), true);
> pci_save_state(pdev);
> - err = pci_set_power_state(pdev, pci_choose_state(pdev, state));
> + err = pci_set_power_state(pdev, PCI_D0);
> if (err)
> goto restore;
I think you can just substitute pci_choose_state(pdev, state) with PCI_D0, not
removing pci_enable_wake()
Regards,
Lorenzo
>
> ?
>
> --
> Best regards,
> Oleksandr Natalenko (post-factum)
> Principal Software Maintenance Engineer
>