Hello All,
Whenever I try to dd a cdrom to an iso image I get an I/O error. This problem
has been present for some time, and I don't know if it's because I use
ide-scsi or not (not been able to test).
Is this still an open issue, and is it likely to get fixed before 2.4.20
final?
Thanks!
DK
--
New York's got the ways and means;
Just won't let you be.
-- The Grateful Dead
More clues please (h/w, error, command, etc.)
>>> DevilKin-LKML <[email protected]> 10/21/02 02:20PM >>>
Hello All,
Whenever I try to dd a cdrom to an iso image I get an I/O error. This problem
has been present for some time, and I don't know if it's because I use
ide-scsi or not (not been able to test).
Is this still an open issue, and is it likely to get fixed before 2.4.20
final?
Thanks!
DK
--
New York's got the ways and means;
Just won't let you be.
-- The Grateful Dead
On Monday 21 October 2002 20:25, Nicholas Berry wrote:
> More clues please (h/w, error, command, etc.)
Kernel: 2.4.20-pre10-ac2. Configuration is attached.
Hardware platform: x86, AMD TBird 2000XP.
Details: the scsi cdrom (writer) fails to read the immage correctly, whereas
the other two (ide-scsi) devices read the image perfectly.
Loaded modules:
--------------------
agpgart es1371 ac97_codec soundcore usb-storage usb-uhci usbcore
via686a i2c-isa i2c-viapro i2c-proc i2c-core ide-scsi aic7xxx sg
sr_mod cdrom sd_mod scsi_mod smbfs nfs lockd sunrpc loop lp
parport_pc parport rtc 3c59x
SCSI Controller
----------------
00:0f.0 SCSI storage controller: Adaptec AHA-7850 (rev 03)
Subsystem: Adaptec AHA-2904/Integrated AIC-7850
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1000ns min, 1000ns max), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e800 [disabled] [size=256]
Region 1: Memory at fb002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
CDROM device:
------------------
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.8
<Adaptec 2902/04/10/15/20/30C SCSI adapter>
aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs
Vendor: PLEXTOR Model: CD-R PX-W4220T Rev: 1.01
Type: CD-ROM ANSI SCSI revision: 02
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 4, lun 0
(scsi0:A:4): 10.000MB/s transfers (10.000MHz, offset 8)
sr0: scsi3-mmc drive: 20x/20x writer cd/rw xa/form2 cdda tray
Device file:
-------------
devilkin@whocares:/tmp$ ls -l /dev/scd0
brw-rw-rw- 1 root disk 11, 0 Jul 18 1994 /dev/scd0
Command executed with valid cdrom in drive:
---------------------------------------------------
devilkin@whocares:/tmp$ dd if=/dev/scd0 of=/tmp/image.iso
dd: reading `/dev/writer': Input/output error
1264984+0 records in
1264984+0 records out
Errors in the system log:
---------------------------
scsi0: ERROR on channel 0, id 4, lun 0, CDB: Read (10) 00 00 04 d3 24 00 00 3f
00
Info fld=0x4d356, Current sd0b:00: sense key Medium Error
Additional sense indicates L-EC uncorrectable error
I/O error: dev 0b:00, sector 1264984
scsi0: ERROR on channel 0, id 4, lun 0, CDB: Read (10) 00 00 04 d3 57 00 00 0c
00
Info fld=0x4d357, Current sd0b:00: sense key Medium Error
I/O error: dev 0b:00, sector 1264988
scsi0: ERROR on channel 0, id 4, lun 0, CDB: Read (10) 00 00 04 d3 58 00 00 0b
00
Info fld=0x4d358, Current sd0b:00: sense key Medium Error
I/O error: dev 0b:00, sector 1264992
scsi0: ERROR on channel 0, id 4, lun 0, CDB: Read (10) 00 00 04 d3 56 00 00 01
00
Info fld=0x4d356, Current sd0b:00: sense key Medium Error
Additional sense indicates L-EC uncorrectable error
I/O error: dev 0b:00, sector 1264984
scsi0: ERROR on channel 0, id 4, lun 0, CDB: Read (10) 00 00 04 d3 57 00 00 01
00
Info fld=0x4d357, Current sd0b:00: sense key Medium Error
I/O error: dev 0b:00, sector 1264988
This happens with close to EVERY cdrom, and I can always read them perfectly
in the other drives. Just doing a file-copy from the disk in the scsi drive
also works. Writing also gives no problems at all.
Strange things are afoot...
DK
--
Bradley's Bromide:
If computers get too powerful, we can organize them into a
committee -- that will do them in.