I'm trying to troubleshoot a failure with my Maxtor hard drive that I have
experienced consistantly, even in the 2.2.x kernels (I'm now running
2.2.1-test10, .config is attached). It detects all of my drives fine:
block: queued sectors max/low 126786kB/95090kB, 384 slots per queue
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c586b IDE UDMA33 controller on pci0:7.1
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
hda: Maxtor 52049U4, ATA DISK drive
hdb: WDC AC31200F, ATA DISK drive
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
hdc: Maxtor 90680D4, ATA DISK drive
hdd: ATAPI 40X CDROM DRIVE, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 40020624 sectors (20491 MB) w/2048KiB Cache, CHS=2491/255/63,
UDMA(33)
hdb: 2503872 sectors (1282 MB) w/64KiB Cache, CHS=621/64/63, DMA
hdc: 13281408 sectors (6800 MB) w/256KiB Cache, CHS=13176/16/63, UDMA(33)
hdd: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33)
And then all the services load up, etc. Once I log in, though, either in
gdm or on the console, it will pause for around 10-15 seconds, and then
display this:
hdc: timeout waiting for DMA
ide_dmaproc: chipset supported ide_dma_timeout func only: 14
hdc: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
hdc: status timeout: status=0xd0 { Busy }
hdc: DMA disabled
hdd: DMA disabled
hdc: drive not ready for command
ide1: reset: success
(hdc is the problem, obviously) Once this occurs, the system appears to
run normally. I don't really care about hdd (cdrom), although I figure
they are probably related somehow.
Windows is able to use UDMA fine on this drive. Also note that this isn't
a UDMA66 drive, and I'm not trying to use it (most of the other posts
I've seen with similar problems were related to 66).
Drives on ide0 seem to run in udma mode just fine, also...
Here's /proc/ide/via:
----------VIA BusMastering IDE Configuration----------------
Driver Version: 2.1e
South Bridge: VIA vt82c586b rev 0x47
Command register: 0x7
Latency timer: 64
PCI clock: 33MHz
Master Read Cycle IRDY: 1ws
Master Write Cycle IRDY: 1ws
FIFO Output Data 1/2 Clock Advance: off
BM IDE Status Register Read Retry: on
Max DRDY Pulse Width: No limit
-----------------------Primary IDE-------Secondary IDE------
Read DMA FIFO flush: on on
End Sect. FIFO flush: on on
Prefetch Buffer: on on
Post Write Buffer: on on
FIFO size: 8 8
Threshold Prim.: 1/2 1/2
Bytes Per Sector: 512 512
Both channels togth: yes yes
-------------------drive0----drive1----drive2----drive3-----
BMDMA enabled: yes yes no no
Transfer Mode: UDMA DMA/PIO UDMA UDMA
Address Setup: 30ns 60ns 30ns 30ns
Active Pulse: 90ns 90ns 90ns 90ns
Recovery Time: 30ns 60ns 30ns 30ns
Cycle Time: 60ns 150ns 60ns 60ns
Transfer Rate: 33.0MB/s 13.2MB/s 33.0MB/s 33.0MB/s
What I don't understand is, the transfer mode still seems to be "UDMA",
but "BMDMA" is not enabled. Aren't they inter-dependant? One in the
same? I'm obviously no expert, so any help would be appreciated.
Thanks in advance,
Ryan
Hey Vojtech,
Thanks for your response. I tried using 2.4.2-pre3 and the same problem
occurs, in exactly the same manner. The only other problem I can identify
is a boot message:
IRQ routing conflict in pirq table for device 00:0a.0
lspci reveals that 00:0a.0 is my network card:
00:0a.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone]
But I'm not sure why that would have any problem, as it works perfectly,
and I don't see any conflicts:
/proc/interrupts:
CPU0
0: 416389 XT-PIC timer
1: 18840 XT-PIC keyboard
2: 0 XT-PIC cascade
8: 1 XT-PIC rtc
9: 135491 XT-PIC soundblaster
10: 83005 XT-PIC eth0
11: 386543 XT-PIC nvidia
12: 121397 XT-PIC PS/2 Mouse
14: 3967 XT-PIC ide0
15: 249701 XT-PIC ide1
NMI: 0
ERR: 0
If you would like any other info, or have any ideas, please let me
know. The cable seems to be fine, and like I said it works okay in
Windows.
Thanks again,
Ryan
On Fri, 9 Feb 2001, Vojtech Pavlik wrote:
> Hi!
>
> Please try 2.4.2-pre kernels, they have a newer VIA IDE driver.
>
> Vojtech
>
> On Wed, Feb 07, 2001 at 03:37:49PM -0600, Ryan Hayle wrote:
> > I'm trying to troubleshoot a failure with my Maxtor hard drive that I have
> > experienced consistantly, even in the 2.2.x kernels (I'm now running
> > 2.2.1-test10, .config is attached). It detects all of my drives fine:
> >
> > block: queued sectors max/low 126786kB/95090kB, 384 slots per queue
> > Uniform Multi-Platform E-IDE driver Revision: 6.31
> > ide: Assuming 33MHz system bus speed for PIO modes; override with
> > idebus=xx
> > VP_IDE: IDE controller on PCI bus 00 dev 39
> > VP_IDE: chipset revision 6
> > VP_IDE: not 100% native mode: will probe irqs later
> > VP_IDE: VIA vt82c586b IDE UDMA33 controller on pci0:7.1
> > ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:DMA, hdb:DMA
> > ide1: BM-DMA at 0xe008-0xe00f, BIOS settings: hdc:DMA, hdd:DMA
> > hda: Maxtor 52049U4, ATA DISK drive
> > hdb: WDC AC31200F, ATA DISK drive
> > ide: Assuming 33MHz system bus speed for PIO modes; override with
> > idebus=xx
> > hdc: Maxtor 90680D4, ATA DISK drive
> > hdd: ATAPI 40X CDROM DRIVE, ATAPI CD/DVD-ROM drive
> > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> > ide1 at 0x170-0x177,0x376 on irq 15
> > hda: 40020624 sectors (20491 MB) w/2048KiB Cache, CHS=2491/255/63,
> > UDMA(33)
> > hdb: 2503872 sectors (1282 MB) w/64KiB Cache, CHS=621/64/63, DMA
> > hdc: 13281408 sectors (6800 MB) w/256KiB Cache, CHS=13176/16/63, UDMA(33)
> > hdd: ATAPI 40X CD-ROM drive, 128kB Cache, UDMA(33)
> >
> > And then all the services load up, etc. Once I log in, though, either in
> > gdm or on the console, it will pause for around 10-15 seconds, and then
> > display this:
> >
> > hdc: timeout waiting for DMA
> > ide_dmaproc: chipset supported ide_dma_timeout func only: 14
> > hdc: irq timeout: status=0x58 { DriveReady SeekComplete DataRequest }
> > hdc: status timeout: status=0xd0 { Busy }
> > hdc: DMA disabled
> > hdd: DMA disabled
> > hdc: drive not ready for command
> > ide1: reset: success
> >
> > (hdc is the problem, obviously) Once this occurs, the system appears to
> > run normally. I don't really care about hdd (cdrom), although I figure
> > they are probably related somehow.
> >
> > Windows is able to use UDMA fine on this drive. Also note that this isn't
> > a UDMA66 drive, and I'm not trying to use it (most of the other posts
> > I've seen with similar problems were related to 66).
> >
> > Drives on ide0 seem to run in udma mode just fine, also...
> >
> > Here's /proc/ide/via:
> >
> > ----------VIA BusMastering IDE Configuration----------------
> > Driver Version: 2.1e
> > South Bridge: VIA vt82c586b rev 0x47
> > Command register: 0x7
> > Latency timer: 64
> > PCI clock: 33MHz
> > Master Read Cycle IRDY: 1ws
> > Master Write Cycle IRDY: 1ws
> > FIFO Output Data 1/2 Clock Advance: off
> > BM IDE Status Register Read Retry: on
> > Max DRDY Pulse Width: No limit
> > -----------------------Primary IDE-------Secondary IDE------
> > Read DMA FIFO flush: on on
> > End Sect. FIFO flush: on on
> > Prefetch Buffer: on on
> > Post Write Buffer: on on
> > FIFO size: 8 8
> > Threshold Prim.: 1/2 1/2
> > Bytes Per Sector: 512 512
> > Both channels togth: yes yes
> > -------------------drive0----drive1----drive2----drive3-----
> > BMDMA enabled: yes yes no no
> > Transfer Mode: UDMA DMA/PIO UDMA UDMA
> > Address Setup: 30ns 60ns 30ns 30ns
> > Active Pulse: 90ns 90ns 90ns 90ns
> > Recovery Time: 30ns 60ns 30ns 30ns
> > Cycle Time: 60ns 150ns 60ns 60ns
> > Transfer Rate: 33.0MB/s 13.2MB/s 33.0MB/s 33.0MB/s
> >
> > What I don't understand is, the transfer mode still seems to be "UDMA",
> > but "BMDMA" is not enabled. Aren't they inter-dependant? One in the
> > same? I'm obviously no expert, so any help would be appreciated.
> >
> > Thanks in advance,
> > Ryan
> >
>
> > #
> > # Automatically generated make config: don't edit
> > #
> > CONFIG_X86=y
> > CONFIG_ISA=y
> > # CONFIG_SBUS is not set
> > CONFIG_UID16=y
> >
> > #
> > # Code maturity level options
> > #
> > CONFIG_EXPERIMENTAL=y
> >
> > #
> > # Loadable module support
> > #
> > CONFIG_MODULES=y
> > CONFIG_MODVERSIONS=y
> > CONFIG_KMOD=y
> >
> > #
> > # Processor type and features
> > #
> > # CONFIG_M386 is not set
> > # CONFIG_M486 is not set
> > # CONFIG_M586 is not set
> > # CONFIG_M586TSC is not set
> > # CONFIG_M586MMX is not set
> > # CONFIG_M686 is not set
> > # CONFIG_MPENTIUMIII is not set
> > # CONFIG_MPENTIUM4 is not set
> > CONFIG_MK6=y
> > # CONFIG_MK7 is not set
> > # CONFIG_MCRUSOE is not set
> > # CONFIG_MWINCHIPC6 is not set
> > # CONFIG_MWINCHIP2 is not set
> > # CONFIG_MWINCHIP3D is not set
> > CONFIG_X86_WP_WORKS_OK=y
> > CONFIG_X86_INVLPG=y
> > CONFIG_X86_CMPXCHG=y
> > CONFIG_X86_BSWAP=y
> > CONFIG_X86_POPAD_OK=y
> > CONFIG_X86_L1_CACHE_SHIFT=5
> > CONFIG_X86_ALIGNMENT_16=y
> > CONFIG_X86_TSC=y
> > CONFIG_X86_USE_PPRO_CHECKSUM=y
> > # CONFIG_TOSHIBA is not set
> > # CONFIG_MICROCODE is not set
> > # CONFIG_X86_MSR is not set
> > # CONFIG_X86_CPUID is not set
> > CONFIG_NOHIGHMEM=y
> > # CONFIG_HIGHMEM4G is not set
> > # CONFIG_HIGHMEM64G is not set
> > # CONFIG_MATH_EMULATION is not set
> > CONFIG_MTRR=y
> > # CONFIG_SMP is not set
> > # CONFIG_X86_UP_IOAPIC is not set
> >
> > #
> > # General setup
> > #
> > CONFIG_NET=y
> > # CONFIG_VISWS is not set
> > CONFIG_PCI=y
> > # CONFIG_PCI_GOBIOS is not set
> > # CONFIG_PCI_GODIRECT is not set
> > CONFIG_PCI_GOANY=y
> > CONFIG_PCI_BIOS=y
> > CONFIG_PCI_DIRECT=y
> > CONFIG_PCI_NAMES=y
> > # CONFIG_EISA is not set
> > # CONFIG_MCA is not set
> > # CONFIG_HOTPLUG is not set
> > # CONFIG_PCMCIA is not set
> > CONFIG_SYSVIPC=y
> > # CONFIG_BSD_PROCESS_ACCT is not set
> > CONFIG_SYSCTL=y
> > CONFIG_KCORE_ELF=y
> > # CONFIG_KCORE_AOUT is not set
> > CONFIG_BINFMT_AOUT=m
> > CONFIG_BINFMT_ELF=y
> > CONFIG_BINFMT_MISC=m
> > CONFIG_PM=y
> > # CONFIG_ACPI is not set
> > # CONFIG_APM is not set
> >
> > #
> > # Memory Technology Devices (MTD)
> > #
> > # CONFIG_MTD is not set
> >
> > #
> > # Parallel port support
> > #
> > CONFIG_PARPORT=m
> > CONFIG_PARPORT_PC=m
> > # CONFIG_PARPORT_PC_FIFO is not set
> > # CONFIG_PARPORT_PC_SUPERIO is not set
> > # CONFIG_PARPORT_AMIGA is not set
> > # CONFIG_PARPORT_MFC3 is not set
> > # CONFIG_PARPORT_ATARI is not set
> > # CONFIG_PARPORT_SUNBPP is not set
> > # CONFIG_PARPORT_OTHER is not set
> > CONFIG_PARPORT_1284=y
> >
> > #
> > # Plug and Play configuration
> > #
> > CONFIG_PNP=y
> > CONFIG_ISAPNP=y
> >
> > #
> > # Block devices
> > #
> > CONFIG_BLK_DEV_FD=y
> > # CONFIG_BLK_DEV_XD is not set
> > # CONFIG_PARIDE is not set
> > # CONFIG_BLK_CPQ_DA is not set
> > # CONFIG_BLK_CPQ_CISS_DA is not set
> > # CONFIG_BLK_DEV_DAC960 is not set
> > CONFIG_BLK_DEV_LOOP=m
> > # CONFIG_BLK_DEV_NBD is not set
> > # CONFIG_BLK_DEV_RAM is not set
> >
> > #
> > # Multi-device support (RAID and LVM)
> > #
> > # CONFIG_MD is not set
> >
> > #
> > # Networking options
> > #
> > CONFIG_PACKET=y
> > # CONFIG_PACKET_MMAP is not set
> > # CONFIG_NETLINK is not set
> > # CONFIG_NETFILTER is not set
> > # CONFIG_FILTER is not set
> > CONFIG_UNIX=y
> > CONFIG_INET=y
> > CONFIG_IP_MULTICAST=y
> > # CONFIG_IP_ADVANCED_ROUTER is not set
> > # CONFIG_IP_PNP is not set
> > # CONFIG_NET_IPIP is not set
> > # CONFIG_NET_IPGRE is not set
> > # CONFIG_IP_MROUTE is not set
> > # CONFIG_INET_ECN is not set
> > # CONFIG_SYN_COOKIES is not set
> > # CONFIG_IPV6 is not set
> > CONFIG_KHTTPD=m
> > # CONFIG_ATM is not set
> >
> > #
> > #
> > #
> > # CONFIG_IPX is not set
> > # CONFIG_ATALK is not set
> > # CONFIG_DECNET is not set
> > # CONFIG_BRIDGE is not set
> > # CONFIG_X25 is not set
> > # CONFIG_LAPB is not set
> > # CONFIG_LLC is not set
> > # CONFIG_NET_DIVERT is not set
> > # CONFIG_ECONET is not set
> > # CONFIG_WAN_ROUTER is not set
> > # CONFIG_NET_FASTROUTE is not set
> > # CONFIG_NET_HW_FLOWCONTROL is not set
> >
> > #
> > # QoS and/or fair queueing
> > #
> > # CONFIG_NET_SCHED is not set
> >
> > #
> > # Telephony Support
> > #
> > # CONFIG_PHONE is not set
> >
> > #
> > # ATA/IDE/MFM/RLL support
> > #
> > CONFIG_IDE=y
> >
> > #
> > # IDE, ATA and ATAPI Block devices
> > #
> > CONFIG_BLK_DEV_IDE=y
> >
> > #
> > # Please see Documentation/ide.txt for help/info on IDE drives
> > #
> > # CONFIG_BLK_DEV_HD_IDE is not set
> > # CONFIG_BLK_DEV_HD is not set
> > CONFIG_BLK_DEV_IDEDISK=y
> > CONFIG_IDEDISK_MULTI_MODE=y
> > # CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
> > # CONFIG_BLK_DEV_COMMERIAL is not set
> > CONFIG_BLK_DEV_IDECD=y
> > # CONFIG_BLK_DEV_IDETAPE is not set
> > # CONFIG_BLK_DEV_IDEFLOPPY is not set
> >
> > #
> > # IDE chipset support/bugfixes
> > #
> > # CONFIG_BLK_DEV_CMD640 is not set
> > # CONFIG_BLK_DEV_ISAPNP is not set
> > # CONFIG_BLK_DEV_RZ1000 is not set
> > CONFIG_BLK_DEV_IDEPCI=y
> > # CONFIG_IDEPCI_SHARE_IRQ is not set
> > CONFIG_BLK_DEV_IDEDMA_PCI=y
> > # CONFIG_BLK_DEV_OFFBOARD is not set
> > CONFIG_IDEDMA_PCI_AUTO=y
> > CONFIG_BLK_DEV_IDEDMA=y
> > # CONFIG_IDEDMA_PCI_WIP is not set
> > # CONFIG_BLK_DEV_AEC62XX is not set
> > # CONFIG_BLK_DEV_ALI15X3 is not set
> > # CONFIG_BLK_DEV_AMD7409 is not set
> > # CONFIG_BLK_DEV_CMD64X is not set
> > # CONFIG_BLK_DEV_CY82C693 is not set
> > # CONFIG_BLK_DEV_CS5530 is not set
> > # CONFIG_BLK_DEV_HPT34X is not set
> > # CONFIG_BLK_DEV_HPT366 is not set
> > # CONFIG_BLK_DEV_PIIX is not set
> > # CONFIG_BLK_DEV_NS87415 is not set
> > # CONFIG_BLK_DEV_OPTI621 is not set
> > # CONFIG_BLK_DEV_PDC202XX is not set
> > # CONFIG_BLK_DEV_OSB4 is not set
> > # CONFIG_BLK_DEV_SIS5513 is not set
> > # CONFIG_BLK_DEV_SLC90E66 is not set
> > # CONFIG_BLK_DEV_TRM290 is not set
> > CONFIG_BLK_DEV_VIA82CXXX=y
> > # CONFIG_IDE_CHIPSETS is not set
> > CONFIG_IDEDMA_AUTO=y
> > # CONFIG_IDEDMA_IVB is not set
> > # CONFIG_DMA_NONPCI is not set
> > CONFIG_BLK_DEV_IDE_MODES=y
> >
> > #
> > # SCSI support
> > #
> > # CONFIG_SCSI is not set
> >
> > #
> > # IEEE 1394 (FireWire) support
> > #
> > # CONFIG_IEEE1394 is not set
> >
> > #
> > # I2O device support
> > #
> > # CONFIG_I2O is not set
> >
> > #
> > # Network device support
> > #
> > CONFIG_NETDEVICES=y
> >
> > #
> > # ARCnet devices
> > #
> > # CONFIG_ARCNET is not set
> > CONFIG_DUMMY=m
> > # CONFIG_BONDING is not set
> > # CONFIG_EQUALIZER is not set
> > # CONFIG_TUN is not set
> > # CONFIG_NET_SB1000 is not set
> >
> > #
> > # Ethernet (10 or 100Mbit)
> > #
> > CONFIG_NET_ETHERNET=y
> > CONFIG_NET_VENDOR_3COM=y
> > # CONFIG_EL1 is not set
> > # CONFIG_EL2 is not set
> > # CONFIG_ELPLUS is not set
> > # CONFIG_EL16 is not set
> > # CONFIG_EL3 is not set
> > # CONFIG_3C515 is not set
> > CONFIG_VORTEX=y
> > # CONFIG_LANCE is not set
> > # CONFIG_NET_VENDOR_SMC is not set
> > # CONFIG_NET_VENDOR_RACAL is not set
> > # CONFIG_AT1700 is not set
> > # CONFIG_DEPCA is not set
> > # CONFIG_HP100 is not set
> > # CONFIG_NET_ISA is not set
> > # CONFIG_NET_PCI is not set
> > # CONFIG_NET_POCKET is not set
> >
> > #
> > # Ethernet (1000 Mbit)
> > #
> > # CONFIG_ACENIC is not set
> > # CONFIG_HAMACHI is not set
> > # CONFIG_YELLOWFIN is not set
> > # CONFIG_SK98LIN is not set
> > # CONFIG_FDDI is not set
> > # CONFIG_HIPPI is not set
> > # CONFIG_PLIP is not set
> > CONFIG_PPP=m
> > # CONFIG_PPP_MULTILINK is not set
> > # CONFIG_PPP_ASYNC is not set
> > # CONFIG_PPP_SYNC_TTY is not set
> > CONFIG_PPP_DEFLATE=m
> > CONFIG_PPP_BSDCOMP=m
> > # CONFIG_PPPOE is not set
> > # CONFIG_SLIP is not set
> >
> > #
> > # Wireless LAN (non-hamradio)
> > #
> > # CONFIG_NET_RADIO is not set
> >
> > #
> > # Token Ring devices
> > #
> > # CONFIG_TR is not set
> > # CONFIG_NET_FC is not set
> > # CONFIG_RCPCI is not set
> > # CONFIG_SHAPER is not set
> >
> > #
> > # Wan interfaces
> > #
> > # CONFIG_WAN is not set
> >
> > #
> > # Amateur Radio support
> > #
> > # CONFIG_HAMRADIO is not set
> >
> > #
> > # IrDA (infrared) support
> > #
> > # CONFIG_IRDA is not set
> >
> > #
> > # ISDN subsystem
> > #
> > # CONFIG_ISDN is not set
> >
> > #
> > # Old CD-ROM drivers (not SCSI, not IDE)
> > #
> > # CONFIG_CD_NO_IDESCSI is not set
> >
> > #
> > # Input core support
> > #
> > CONFIG_INPUT=m
> > # CONFIG_INPUT_KEYBDEV is not set
> > # CONFIG_INPUT_MOUSEDEV is not set
> > # CONFIG_INPUT_JOYDEV is not set
> > # CONFIG_INPUT_EVDEV is not set
> >
> > #
> > # Character devices
> > #
> > CONFIG_VT=y
> > CONFIG_VT_CONSOLE=y
> > CONFIG_SERIAL=y
> > # CONFIG_SERIAL_CONSOLE is not set
> > # CONFIG_SERIAL_EXTENDED is not set
> > # CONFIG_SERIAL_NONSTANDARD is not set
> > CONFIG_UNIX98_PTYS=y
> > CONFIG_UNIX98_PTY_COUNT=512
> > CONFIG_PRINTER=m
> > # CONFIG_LP_CONSOLE is not set
> > # CONFIG_PPDEV is not set
> >
> > #
> > # I2C support
> > #
> > CONFIG_I2C=m
> > CONFIG_I2C_ALGOBIT=m
> > # CONFIG_I2C_PHILIPSPAR is not set
> > # CONFIG_I2C_ELV is not set
> > # CONFIG_I2C_VELLEMAN is not set
> > # CONFIG_I2C_ALGOPCF is not set
> > # CONFIG_I2C_CHARDEV is not set
> >
> > #
> > # Mice
> > #
> > # CONFIG_BUSMOUSE is not set
> > CONFIG_MOUSE=y
> > CONFIG_PSMOUSE=y
> > # CONFIG_82C710_MOUSE is not set
> > # CONFIG_PC110_PAD is not set
> >
> > #
> > # Joysticks
> > #
> > CONFIG_JOYSTICK=y
> >
> > #
> > # Game port support
> > #
> > # CONFIG_INPUT_NS558 is not set
> > # CONFIG_INPUT_LIGHTNING is not set
> > # CONFIG_INPUT_PCIGAME is not set
> >
> > #
> > # Gameport joysticks
> > #
> > CONFIG_INPUT_ANALOG=m
> > # CONFIG_INPUT_A3D is not set
> > # CONFIG_INPUT_ADI is not set
> > # CONFIG_INPUT_COBRA is not set
> > # CONFIG_INPUT_GF2K is not set
> > # CONFIG_INPUT_GRIP is not set
> > # CONFIG_INPUT_INTERACT is not set
> > # CONFIG_INPUT_TMDC is not set
> > # CONFIG_INPUT_SIDEWINDER is not set
> >
> > #
> > # Serial port support
> > #
> > # CONFIG_INPUT_SERPORT is not set
> >
> > #
> > # Serial port joysticks
> > #
> > # CONFIG_INPUT_WARRIOR is not set
> > # CONFIG_INPUT_MAGELLAN is not set
> > # CONFIG_INPUT_SPACEORB is not set
> > # CONFIG_INPUT_SPACEBALL is not set
> > # CONFIG_INPUT_IFORCE_232 is not set
> >
> > #
> > # Parallel port joysticks
> > #
> > # CONFIG_INPUT_DB9 is not set
> > # CONFIG_INPUT_GAMECON is not set
> > # CONFIG_INPUT_TURBOGRAFX is not set
> > # CONFIG_QIC02_TAPE is not set
> >
> > #
> > # Watchdog Cards
> > #
> > # CONFIG_WATCHDOG is not set
> > # CONFIG_INTEL_RNG is not set
> > # CONFIG_NVRAM is not set
> > CONFIG_RTC=m
> > # CONFIG_DTLK is not set
> > # CONFIG_R3964 is not set
> > # CONFIG_APPLICOM is not set
> >
> > #
> > # Ftape, the floppy tape device driver
> > #
> > # CONFIG_FTAPE is not set
> > # CONFIG_AGP is not set
> > # CONFIG_DRM is not set
> >
> > #
> > # Multimedia devices
> > #
> > CONFIG_VIDEO_DEV=m
> >
> > #
> > # Video For Linux
> > #
> > CONFIG_VIDEO_PROC_FS=y
> > # CONFIG_I2C_PARPORT is not set
> >
> > #
> > # Video Adapters
> > #
> > CONFIG_VIDEO_BT848=m
> > # CONFIG_VIDEO_PMS is not set
> > # CONFIG_VIDEO_BWQCAM is not set
> > # CONFIG_VIDEO_CQCAM is not set
> > # CONFIG_VIDEO_CPIA is not set
> > # CONFIG_VIDEO_SAA5249 is not set
> > # CONFIG_TUNER_3036 is not set
> > # CONFIG_VIDEO_STRADIS is not set
> > # CONFIG_VIDEO_ZORAN is not set
> > # CONFIG_VIDEO_ZR36120 is not set
> >
> > #
> > # Radio Adapters
> > #
> > # CONFIG_RADIO_CADET is not set
> > # CONFIG_RADIO_RTRACK is not set
> > # CONFIG_RADIO_RTRACK2 is not set
> > # CONFIG_RADIO_AZTECH is not set
> > # CONFIG_RADIO_GEMTEK is not set
> > # CONFIG_RADIO_MAESTRO is not set
> > # CONFIG_RADIO_MIROPCM20 is not set
> > # CONFIG_RADIO_SF16FMI is not set
> > # CONFIG_RADIO_TERRATEC is not set
> > # CONFIG_RADIO_TRUST is not set
> > # CONFIG_RADIO_TYPHOON is not set
> > # CONFIG_RADIO_ZOLTRIX is not set
> >
> > #
> > # File systems
> > #
> > # CONFIG_QUOTA is not set
> > # CONFIG_AUTOFS_FS is not set
> > CONFIG_AUTOFS4_FS=y
> > # CONFIG_REISERFS_FS is not set
> > # CONFIG_ADFS_FS is not set
> > # CONFIG_AFFS_FS is not set
> > # CONFIG_HFS_FS is not set
> > # CONFIG_BFS_FS is not set
> > CONFIG_FAT_FS=y
> > # CONFIG_MSDOS_FS is not set
> > CONFIG_VFAT_FS=y
> > # CONFIG_EFS_FS is not set
> > CONFIG_JFFS_FS_VERBOSE=0
> > # CONFIG_CRAMFS is not set
> > # CONFIG_RAMFS is not set
> > CONFIG_ISO9660_FS=m
> > CONFIG_JOLIET=y
> > # CONFIG_MINIX_FS is not set
> > # CONFIG_NTFS_FS is not set
> > # CONFIG_HPFS_FS is not set
> > CONFIG_PROC_FS=y
> > # CONFIG_DEVFS_FS is not set
> > CONFIG_DEVPTS_FS=y
> > # CONFIG_QNX4FS_FS is not set
> > # CONFIG_ROMFS_FS is not set
> > CONFIG_EXT2_FS=y
> > # CONFIG_SYSV_FS is not set
> > # CONFIG_UDF_FS is not set
> > # CONFIG_UFS_FS is not set
> >
> > #
> > # Network File Systems
> > #
> > # CONFIG_CODA_FS is not set
> > # CONFIG_NFS_FS is not set
> > # CONFIG_NFSD is not set
> > # CONFIG_SUNRPC is not set
> > # CONFIG_LOCKD is not set
> > CONFIG_SMB_FS=m
> > CONFIG_SMB_NLS_DEFAULT=y
> > CONFIG_SMB_NLS_REMOTE="cp437"
> > # CONFIG_NCP_FS is not set
> >
> > #
> > # Partition Types
> > #
> > # CONFIG_PARTITION_ADVANCED is not set
> > CONFIG_MSDOS_PARTITION=y
> > CONFIG_SMB_NLS=y
> > CONFIG_NLS=y
> >
> > #
> > # Native Language Support
> > #
> > CONFIG_NLS_DEFAULT="iso8859-1"
> > CONFIG_NLS_CODEPAGE_437=m
> > # CONFIG_NLS_CODEPAGE_737 is not set
> > # CONFIG_NLS_CODEPAGE_775 is not set
> > # CONFIG_NLS_CODEPAGE_850 is not set
> > # CONFIG_NLS_CODEPAGE_852 is not set
> > # CONFIG_NLS_CODEPAGE_855 is not set
> > # CONFIG_NLS_CODEPAGE_857 is not set
> > # CONFIG_NLS_CODEPAGE_860 is not set
> > # CONFIG_NLS_CODEPAGE_861 is not set
> > # CONFIG_NLS_CODEPAGE_862 is not set
> > # CONFIG_NLS_CODEPAGE_863 is not set
> > # CONFIG_NLS_CODEPAGE_864 is not set
> > # CONFIG_NLS_CODEPAGE_865 is not set
> > # CONFIG_NLS_CODEPAGE_866 is not set
> > # CONFIG_NLS_CODEPAGE_869 is not set
> > # CONFIG_NLS_CODEPAGE_874 is not set
> > # CONFIG_NLS_CODEPAGE_932 is not set
> > # CONFIG_NLS_CODEPAGE_936 is not set
> > # CONFIG_NLS_CODEPAGE_949 is not set
> > # CONFIG_NLS_CODEPAGE_950 is not set
> > CONFIG_NLS_ISO8859_1=y
> > # CONFIG_NLS_ISO8859_2 is not set
> > # CONFIG_NLS_ISO8859_3 is not set
> > # CONFIG_NLS_ISO8859_4 is not set
> > # CONFIG_NLS_ISO8859_5 is not set
> > # CONFIG_NLS_ISO8859_6 is not set
> > # CONFIG_NLS_ISO8859_7 is not set
> > # CONFIG_NLS_ISO8859_8 is not set
> > # CONFIG_NLS_ISO8859_9 is not set
> > # CONFIG_NLS_ISO8859_14 is not set
> > # CONFIG_NLS_ISO8859_15 is not set
> > # CONFIG_NLS_KOI8_R is not set
> > # CONFIG_NLS_UTF8 is not set
> >
> > #
> > # Console drivers
> > #
> > CONFIG_VGA_CONSOLE=y
> > CONFIG_VIDEO_SELECT=y
> > # CONFIG_MDA_CONSOLE is not set
> >
> > #
> > # Frame-buffer support
> > #
> > CONFIG_FB=y
> > CONFIG_DUMMY_CONSOLE=y
> > # CONFIG_FB_RIVA is not set
> > # CONFIG_FB_CLGEN is not set
> > # CONFIG_FB_PM2 is not set
> > # CONFIG_FB_CYBER2000 is not set
> > CONFIG_FB_VESA=y
> > # CONFIG_FB_VGA16 is not set
> > # CONFIG_FB_HGA is not set
> > CONFIG_VIDEO_SELECT=y
> > # CONFIG_FB_MATROX is not set
> > # CONFIG_FB_ATY is not set
> > # CONFIG_FB_ATY128 is not set
> > # CONFIG_FB_3DFX is not set
> > # CONFIG_FB_SIS is not set
> > # CONFIG_FB_VIRTUAL is not set
> > # CONFIG_FBCON_ADVANCED is not set
> > CONFIG_FBCON_CFB8=y
> > CONFIG_FBCON_CFB16=y
> > CONFIG_FBCON_CFB24=y
> > CONFIG_FBCON_CFB32=y
> > # CONFIG_FBCON_FONTWIDTH8_ONLY is not set
> > # CONFIG_FBCON_FONTS is not set
> > CONFIG_FONT_8x8=y
> > CONFIG_FONT_8x16=y
> >
> > #
> > # Sound
> > #
> > CONFIG_SOUND=y
> > # CONFIG_SOUND_CMPCI is not set
> > # CONFIG_SOUND_EMU10K1 is not set
> > # CONFIG_SOUND_FUSION is not set
> > # CONFIG_SOUND_CS4281 is not set
> > # CONFIG_SOUND_ES1370 is not set
> > # CONFIG_SOUND_ES1371 is not set
> > # CONFIG_SOUND_ESSSOLO1 is not set
> > # CONFIG_SOUND_MAESTRO is not set
> > # CONFIG_SOUND_SONICVIBES is not set
> > # CONFIG_SOUND_TRIDENT is not set
> > # CONFIG_SOUND_MSNDCLAS is not set
> > # CONFIG_SOUND_MSNDPIN is not set
> > # CONFIG_SOUND_VIA82CXXX is not set
> > CONFIG_SOUND_OSS=y
> > # CONFIG_SOUND_TRACEINIT is not set
> > CONFIG_SOUND_DMAP=y
> > # CONFIG_SOUND_AD1816 is not set
> > # CONFIG_SOUND_SGALAXY is not set
> > # CONFIG_SOUND_ADLIB is not set
> > # CONFIG_SOUND_ACI_MIXER is not set
> > # CONFIG_SOUND_CS4232 is not set
> > # CONFIG_SOUND_SSCAPE is not set
> > # CONFIG_SOUND_GUS is not set
> > # CONFIG_SOUND_ICH is not set
> > # CONFIG_SOUND_VMIDI is not set
> > # CONFIG_SOUND_TRIX is not set
> > # CONFIG_SOUND_MSS is not set
> > # CONFIG_SOUND_MPU401 is not set
> > # CONFIG_SOUND_NM256 is not set
> > # CONFIG_SOUND_MAD16 is not set
> > # CONFIG_SOUND_PAS is not set
> > # CONFIG_SOUND_PSS is not set
> > CONFIG_SOUND_SB=y
> > CONFIG_SOUND_AWE32_SYNTH=y
> > # CONFIG_SOUND_WAVEFRONT is not set
> > # CONFIG_SOUND_MAUI is not set
> > CONFIG_SOUND_YM3812=y
> > # CONFIG_SOUND_OPL3SA1 is not set
> > # CONFIG_SOUND_OPL3SA2 is not set
> > # CONFIG_SOUND_YMPCI is not set
> > # CONFIG_SOUND_YMFPCI is not set
> > # CONFIG_SOUND_UART6850 is not set
> > # CONFIG_SOUND_AEDSP16 is not set
> > # CONFIG_SOUND_TVMIXER is not set
> >
> > #
> > # USB support
> > #
> > # CONFIG_USB is not set
> >
> > #
> > # Kernel hacking
> > #
> > CONFIG_MAGIC_SYSRQ=y
>
>
>