There are unexpected processes when enabling autosuspend.
These patches are used to fix them.
Hayes Wang (3):
r8152: clear SELECTIVE_SUSPEND when autoresuming
r8152: reset tp->speed before autoresuming in open function
r8152: check WORK_ENABLE in suspend function
drivers/net/usb/r8152.c | 14 +++++++++-----
1 file changed, 9 insertions(+), 5 deletions(-)
--
1.9.3
If (tp->speed & LINK_STATUS) is not zero, the rtl8152_resume()
would call rtl_start_rx() before enabling the tx/rx. Avoid this
by resetting it to zero.
Signed-off-by: Hayes Wang <[email protected]>
---
drivers/net/usb/r8152.c | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c
index a17ca58..f224231 100644
--- a/drivers/net/usb/r8152.c
+++ b/drivers/net/usb/r8152.c
@@ -2891,6 +2891,9 @@ static int rtl8152_open(struct net_device *netdev)
if (res)
goto out;
+ /* set speed to 0 to avoid autoresume try to submit rx */
+ tp->speed = 0;
+
res = usb_autopm_get_interface(tp->intf);
if (res < 0) {
free_all_mem(tp);
@@ -2904,6 +2907,8 @@ static int rtl8152_open(struct net_device *netdev)
clear_bit(WORK_ENABLE, &tp->flags);
usb_kill_urb(tp->intr_urb);
cancel_delayed_work_sync(&tp->schedule);
+
+ /* disable the tx/rx, if the workqueue has enabled them. */
if (tp->speed & LINK_STATUS)
tp->rtl_ops.disable(tp);
}
--
1.9.3
Avoid unnecessary behavior when autosuspend occurs during open().
The relative processes should only be run after finishing open().
Signed-off-by: Hayes Wang <[email protected]>
---
drivers/net/usb/r8152.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c
index f224231..ca3c5d5 100644
--- a/drivers/net/usb/r8152.c
+++ b/drivers/net/usb/r8152.c
@@ -3207,7 +3207,7 @@ static int rtl8152_suspend(struct usb_interface *intf, pm_message_t message)
netif_device_detach(netdev);
}
- if (netif_running(netdev)) {
+ if (netif_running(netdev) && test_bit(WORK_ENABLE, &tp->flags)) {
clear_bit(WORK_ENABLE, &tp->flags);
usb_kill_urb(tp->intr_urb);
tasklet_disable(&tp->tl);
--
1.9.3
The flag of SELECTIVE_SUSPEND should be cleared when autoresuming.
Otherwise, when the system suspend and resume occur, it may have
the wrong flow.
Besides, because the flag of SELECTIVE_SUSPEND couldn't be used
to check if the hw enables the relative feature, it should alwayes
be disabled in close().
Signed-off-by: Hayes Wang <[email protected]>
---
drivers/net/usb/r8152.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
diff --git a/drivers/net/usb/r8152.c b/drivers/net/usb/r8152.c
index e3d84c3..a17ca58 100644
--- a/drivers/net/usb/r8152.c
+++ b/drivers/net/usb/r8152.c
@@ -2955,10 +2955,7 @@ static int rtl8152_close(struct net_device *netdev)
* be disable when autoresume occurs, because the
* netif_running() would be false.
*/
- if (test_bit(SELECTIVE_SUSPEND, &tp->flags)) {
- rtl_runtime_suspend_enable(tp, false);
- clear_bit(SELECTIVE_SUSPEND, &tp->flags);
- }
+ rtl_runtime_suspend_enable(tp, false);
tasklet_disable(&tp->tl);
tp->rtl_ops.down(tp);
@@ -3253,6 +3250,8 @@ static int rtl8152_resume(struct usb_interface *intf)
set_bit(WORK_ENABLE, &tp->flags);
}
usb_submit_urb(tp->intr_urb, GFP_KERNEL);
+ } else if (test_bit(SELECTIVE_SUSPEND, &tp->flags)) {
+ clear_bit(SELECTIVE_SUSPEND, &tp->flags);
}
mutex_unlock(&tp->control);
--
1.9.3
From: Hayes Wang <[email protected]>
Date: Wed, 29 Oct 2014 11:12:14 +0800
> There are unexpected processes when enabling autosuspend.
> These patches are used to fix them.
Series applied, thank you.