This patch set fixes some issues found with the Tegra CLK drivers
in testing. There are also a few patches which clean up the code
and fix some naming issues.
Andrew Bresticker (1):
clk: tegra: pll: Fix potential sleeping-while-atomic
Mark Kuo (2):
clk: tegra: pll: Do not disable PLLE when under HW control
clk: tegra: pll: Fix PLLE SS config
Rhyland Klein (6):
clk: tegra: Fix divider on VI_I2C
clk: tegra210: Remove improper flags for lock_enable
clk: tegra210: Fix naming of MISC registers
clk: tegra: Fix the misnaming of nvenc from msenc
clk: tegra210: fix pllx dyn step calculation
clk: tegra210: Initialize PLL_D2 to a sane rate
drivers/clk/tegra/clk-pll.c | 50 +++++++++++++--------
drivers/clk/tegra/clk-tegra-periph.c | 4 +-
drivers/clk/tegra/clk-tegra210.c | 87 +++++++++++++++---------------------
3 files changed, 71 insertions(+), 70 deletions(-)
--
1.9.1
VI-I2C has 16 bits available for its divider. Switch the divider
width to 16 instead of 8 so correct rates can be set.
Signed-off-by: Rhyland Klein <[email protected]>
---
drivers/clk/tegra/clk-tegra-periph.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/clk/tegra/clk-tegra-periph.c b/drivers/clk/tegra/clk-tegra-periph.c
index 6ad381a888a6..105405ca85ab 100644
--- a/drivers/clk/tegra/clk-tegra-periph.c
+++ b/drivers/clk/tegra/clk-tegra-periph.c
@@ -782,7 +782,7 @@ static struct tegra_periph_init_data periph_clks[] = {
NODIV("sor1", mux_clkm_sor1_brick_sor1_src, CLK_SOURCE_SOR1, 15, MASK(1), 183, 0, tegra_clk_sor1, &sor1_lock),
MUX8("sdmmc_legacy", mux_pllp_out3_clkm_pllp_pllc4, CLK_SOURCE_SDMMC_LEGACY, 193, TEGRA_PERIPH_ON_APB | TEGRA_PERIPH_NO_RESET, tegra_clk_sdmmc_legacy),
MUX8("qspi", mux_pllp_pllc_pllc_out1_pllc4_out2_pllc4_out1_clkm_pllc4_out0, CLK_SOURCE_QSPI, 211, TEGRA_PERIPH_ON_APB, tegra_clk_qspi),
- MUX("vii2c", mux_pllp_pllc_clkm, CLK_SOURCE_VI_I2C, 208, TEGRA_PERIPH_ON_APB, tegra_clk_vi_i2c),
+ I2C("vii2c", mux_pllp_pllc_clkm, CLK_SOURCE_VI_I2C, 208, tegra_clk_vi_i2c),
MUX("mipibif", mux_pllp_clkm, CLK_SOURCE_MIPIBIF, 173, TEGRA_PERIPH_ON_APB, tegra_clk_mipibif),
MUX("uartape", mux_pllp_pllc_clkm, CLK_SOURCE_UARTAPE, 212, TEGRA_PERIPH_ON_APB | TEGRA_PERIPH_NO_RESET, tegra_clk_uartape),
MUX8("tsecb", mux_pllp_pllc2_c_c3_clkm, CLK_SOURCE_TSECB, 206, 0, tegra_clk_tsecb),
--
1.9.1
Most PLL's don't actually have LOCK_ENABLE bits. However, most PLL's
also had that flag set, which meant that the clk code was trying to
enable locks, and inadvertantly flipping bits in other fields.
For PLLM, ensure the correct register is used for the misc_register.
PLL_MISC0 contains the EN_LCKDET bit which should be used for enabling
the lock, and PLLM_MISC1 shouldn't be used at all.
Lastly, remove some of the settings which would point to the EN_LCKDET
bits for some PLLs. There is no need to enable the locks, and that is
done as part of the set_defaults logic already.
Signed-off-by: Rhyland Klein <[email protected]>
---
drivers/clk/tegra/clk-tegra210.c | 42 ++++++++++++++--------------------------
1 file changed, 14 insertions(+), 28 deletions(-)
diff --git a/drivers/clk/tegra/clk-tegra210.c b/drivers/clk/tegra/clk-tegra210.c
index 58514c44ea83..f45c9adf7fb2 100644
--- a/drivers/clk/tegra/clk-tegra210.c
+++ b/drivers/clk/tegra/clk-tegra210.c
@@ -1386,7 +1386,7 @@ static struct tegra_clk_pll_params pll_c_params = {
.mdiv_default = 3,
.div_nmp = &pllc_nmp,
.freq_table = pll_cx_freq_table,
- .flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+ .flags = TEGRA_PLL_USE_LOCK,
.set_defaults = _pllc_set_defaults,
.calc_rate = tegra210_pll_fixed_mdiv_cfg,
};
@@ -1425,7 +1425,7 @@ static struct tegra_clk_pll_params pll_c2_params = {
.ext_misc_reg[2] = PLLC2_MISC2,
.ext_misc_reg[3] = PLLC2_MISC3,
.freq_table = pll_cx_freq_table,
- .flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+ .flags = TEGRA_PLL_USE_LOCK,
.set_defaults = _pllc2_set_defaults,
.calc_rate = tegra210_pll_fixed_mdiv_cfg,
};
@@ -1455,7 +1455,7 @@ static struct tegra_clk_pll_params pll_c3_params = {
.ext_misc_reg[2] = PLLC3_MISC2,
.ext_misc_reg[3] = PLLC3_MISC3,
.freq_table = pll_cx_freq_table,
- .flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+ .flags = TEGRA_PLL_USE_LOCK,
.set_defaults = _pllc3_set_defaults,
.calc_rate = tegra210_pll_fixed_mdiv_cfg,
};
@@ -1505,7 +1505,6 @@ static struct tegra_clk_pll_params pll_c4_vco_params = {
.base_reg = PLLC4_BASE,
.misc_reg = PLLC4_MISC0,
.lock_mask = PLL_BASE_LOCK,
- .lock_enable_bit_idx = PLLSS_MISC_LOCK_ENABLE,
.lock_delay = 300,
.max_p = PLL_QLIN_PDIV_MAX,
.ext_misc_reg[0] = PLLC4_MISC0,
@@ -1517,8 +1516,7 @@ static struct tegra_clk_pll_params pll_c4_vco_params = {
.div_nmp = &pllss_nmp,
.freq_table = pll_c4_vco_freq_table,
.set_defaults = tegra210_pllc4_set_defaults,
- .flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE |
- TEGRA_PLL_VCO_OUT,
+ .flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_VCO_OUT,
.calc_rate = tegra210_pll_fixed_mdiv_cfg,
};
@@ -1559,7 +1557,7 @@ static struct tegra_clk_pll_params pll_m_params = {
.vco_min = 800000000,
.vco_max = 1866000000,
.base_reg = PLLM_BASE,
- .misc_reg = PLLM_MISC1,
+ .misc_reg = PLLM_MISC0,
.lock_mask = PLL_BASE_LOCK,
.lock_enable_bit_idx = PLLM_MISC_LOCK_ENABLE,
.lock_delay = 300,
@@ -1588,7 +1586,6 @@ static struct tegra_clk_pll_params pll_mb_params = {
.base_reg = PLLMB_BASE,
.misc_reg = PLLMB_MISC0,
.lock_mask = PLL_BASE_LOCK,
- .lock_enable_bit_idx = PLLMB_MISC_LOCK_ENABLE,
.lock_delay = 300,
.iddq_reg = PLLMB_MISC0,
.iddq_bit_idx = PLLMB_IDDQ_BIT,
@@ -1598,7 +1595,7 @@ static struct tegra_clk_pll_params pll_mb_params = {
.pdiv_tohw = pll_qlin_pdiv_to_hw,
.div_nmp = &pllm_nmp,
.freq_table = pll_m_freq_table,
- .flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+ .flags = TEGRA_PLL_USE_LOCK,
.set_defaults = tegra210_pllmb_set_defaults,
.calc_rate = tegra210_pll_fixed_mdiv_cfg,
};
@@ -1671,7 +1668,6 @@ static struct tegra_clk_pll_params pll_re_vco_params = {
.base_reg = PLLRE_BASE,
.misc_reg = PLLRE_MISC0,
.lock_mask = PLLRE_MISC_LOCK,
- .lock_enable_bit_idx = PLLRE_MISC_LOCK_ENABLE,
.lock_delay = 300,
.max_p = PLL_QLIN_PDIV_MAX,
.ext_misc_reg[0] = PLLRE_MISC0,
@@ -1681,8 +1677,7 @@ static struct tegra_clk_pll_params pll_re_vco_params = {
.pdiv_tohw = pll_qlin_pdiv_to_hw,
.div_nmp = &pllre_nmp,
.freq_table = pll_re_vco_freq_table,
- .flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_LOCK_MISC |
- TEGRA_PLL_HAS_LOCK_ENABLE | TEGRA_PLL_VCO_OUT,
+ .flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_LOCK_MISC | TEGRA_PLL_VCO_OUT,
.set_defaults = tegra210_pllre_set_defaults,
.calc_rate = tegra210_pll_fixed_mdiv_cfg,
};
@@ -1712,7 +1707,6 @@ static struct tegra_clk_pll_params pll_p_params = {
.base_reg = PLLP_BASE,
.misc_reg = PLLP_MISC0,
.lock_mask = PLL_BASE_LOCK,
- .lock_enable_bit_idx = PLLP_MISC_LOCK_ENABLE,
.lock_delay = 300,
.iddq_reg = PLLP_MISC0,
.iddq_bit_idx = PLLXP_IDDQ_BIT,
@@ -1721,8 +1715,7 @@ static struct tegra_clk_pll_params pll_p_params = {
.div_nmp = &pllp_nmp,
.freq_table = pll_p_freq_table,
.fixed_rate = 408000000,
- .flags = TEGRA_PLL_FIXED | TEGRA_PLL_USE_LOCK |
- TEGRA_PLL_HAS_LOCK_ENABLE | TEGRA_PLL_VCO_OUT,
+ .flags = TEGRA_PLL_FIXED | TEGRA_PLL_USE_LOCK | TEGRA_PLL_VCO_OUT,
.set_defaults = tegra210_pllp_set_defaults,
.calc_rate = tegra210_pll_fixed_mdiv_cfg,
};
@@ -1750,7 +1743,7 @@ static struct tegra_clk_pll_params pll_a1_params = {
.ext_misc_reg[2] = PLLA1_MISC2,
.ext_misc_reg[3] = PLLA1_MISC3,
.freq_table = pll_cx_freq_table,
- .flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+ .flags = TEGRA_PLL_USE_LOCK,
.set_defaults = _plla1_set_defaults,
.calc_rate = tegra210_pll_fixed_mdiv_cfg,
};
@@ -1787,7 +1780,6 @@ static struct tegra_clk_pll_params pll_a_params = {
.base_reg = PLLA_BASE,
.misc_reg = PLLA_MISC0,
.lock_mask = PLL_BASE_LOCK,
- .lock_enable_bit_idx = PLLA_MISC_LOCK_ENABLE,
.lock_delay = 300,
.round_p_to_pdiv = pll_qlin_p_to_pdiv,
.pdiv_tohw = pll_qlin_pdiv_to_hw,
@@ -1802,8 +1794,7 @@ static struct tegra_clk_pll_params pll_a_params = {
.ext_misc_reg[1] = PLLA_MISC1,
.ext_misc_reg[2] = PLLA_MISC2,
.freq_table = pll_a_freq_table,
- .flags = TEGRA_PLL_USE_LOCK | TEGRA_MDIV_NEW |
- TEGRA_PLL_HAS_LOCK_ENABLE,
+ .flags = TEGRA_PLL_USE_LOCK | TEGRA_MDIV_NEW,
.set_defaults = tegra210_plla_set_defaults,
.calc_rate = tegra210_pll_fixed_mdiv_cfg,
.set_gain = tegra210_clk_pll_set_gain,
@@ -1836,7 +1827,6 @@ static struct tegra_clk_pll_params pll_d_params = {
.base_reg = PLLD_BASE,
.misc_reg = PLLD_MISC0,
.lock_mask = PLL_BASE_LOCK,
- .lock_enable_bit_idx = PLLD_MISC_LOCK_ENABLE,
.lock_delay = 1000,
.iddq_reg = PLLD_MISC0,
.iddq_bit_idx = PLLD_IDDQ_BIT,
@@ -1850,7 +1840,7 @@ static struct tegra_clk_pll_params pll_d_params = {
.ext_misc_reg[0] = PLLD_MISC0,
.ext_misc_reg[1] = PLLD_MISC1,
.freq_table = pll_d_freq_table,
- .flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+ .flags = TEGRA_PLL_USE_LOCK,
.mdiv_default = 1,
.set_defaults = tegra210_plld_set_defaults,
.calc_rate = tegra210_pll_fixed_mdiv_cfg,
@@ -1876,7 +1866,6 @@ static struct tegra_clk_pll_params pll_d2_params = {
.base_reg = PLLD2_BASE,
.misc_reg = PLLD2_MISC0,
.lock_mask = PLL_BASE_LOCK,
- .lock_enable_bit_idx = PLLSS_MISC_LOCK_ENABLE,
.lock_delay = 300,
.iddq_reg = PLLD2_BASE,
.iddq_bit_idx = PLLSS_IDDQ_BIT,
@@ -1897,7 +1886,7 @@ static struct tegra_clk_pll_params pll_d2_params = {
.mdiv_default = 1,
.freq_table = tegra210_pll_d2_freq_table,
.set_defaults = tegra210_plld2_set_defaults,
- .flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+ .flags = TEGRA_PLL_USE_LOCK,
.calc_rate = tegra210_pll_fixed_mdiv_cfg,
.set_gain = tegra210_clk_pll_set_gain,
.adjust_vco = tegra210_clk_adjust_vco_min,
@@ -1920,7 +1909,6 @@ static struct tegra_clk_pll_params pll_dp_params = {
.base_reg = PLLDP_BASE,
.misc_reg = PLLDP_MISC,
.lock_mask = PLL_BASE_LOCK,
- .lock_enable_bit_idx = PLLSS_MISC_LOCK_ENABLE,
.lock_delay = 300,
.iddq_reg = PLLDP_BASE,
.iddq_bit_idx = PLLSS_IDDQ_BIT,
@@ -1941,7 +1929,7 @@ static struct tegra_clk_pll_params pll_dp_params = {
.mdiv_default = 1,
.freq_table = pll_dp_freq_table,
.set_defaults = tegra210_plldp_set_defaults,
- .flags = TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE,
+ .flags = TEGRA_PLL_USE_LOCK,
.calc_rate = tegra210_pll_fixed_mdiv_cfg,
.set_gain = tegra210_clk_pll_set_gain,
.adjust_vco = tegra210_clk_adjust_vco_min,
@@ -1973,7 +1961,6 @@ static struct tegra_clk_pll_params pll_u_vco_params = {
.base_reg = PLLU_BASE,
.misc_reg = PLLU_MISC0,
.lock_mask = PLL_BASE_LOCK,
- .lock_enable_bit_idx = PLLU_MISC_LOCK_ENABLE,
.lock_delay = 1000,
.iddq_reg = PLLU_MISC0,
.iddq_bit_idx = PLLU_IDDQ_BIT,
@@ -1983,8 +1970,7 @@ static struct tegra_clk_pll_params pll_u_vco_params = {
.pdiv_tohw = pll_qlin_pdiv_to_hw,
.div_nmp = &pllu_nmp,
.freq_table = pll_u_freq_table,
- .flags = TEGRA_PLLU | TEGRA_PLL_USE_LOCK | TEGRA_PLL_HAS_LOCK_ENABLE |
- TEGRA_PLL_VCO_OUT,
+ .flags = TEGRA_PLLU | TEGRA_PLL_USE_LOCK | TEGRA_PLL_VCO_OUT,
.set_defaults = tegra210_pllu_set_defaults,
.calc_rate = tegra210_pll_fixed_mdiv_cfg,
};
--
1.9.1
Some register for PLLM and PLLMB were named MISC0 but according to the
TRM, they have different names. Sync up the names to make it easier to
understand which register they are really referring to.
Signed-off-by: Rhyland Klein <[email protected]>
---
drivers/clk/tegra/clk-tegra210.c | 36 ++++++++++++++++++------------------
1 file changed, 18 insertions(+), 18 deletions(-)
diff --git a/drivers/clk/tegra/clk-tegra210.c b/drivers/clk/tegra/clk-tegra210.c
index f45c9adf7fb2..2a7faa357130 100644
--- a/drivers/clk/tegra/clk-tegra210.c
+++ b/drivers/clk/tegra/clk-tegra210.c
@@ -59,7 +59,7 @@
#define PLLC3_MISC3 0x50c
#define PLLM_BASE 0x90
-#define PLLM_MISC0 0x9c
+#define PLLM_MISC2 0x9c
#define PLLM_MISC1 0x98
#define PLLP_BASE 0xa0
#define PLLP_MISC0 0xac
@@ -99,7 +99,7 @@
#define PLLC4_MISC0 0x5a8
#define PLLC4_OUT 0x5e4
#define PLLMB_BASE 0x5e8
-#define PLLMB_MISC0 0x5ec
+#define PLLMB_MISC1 0x5ec
#define PLLA1_BASE 0x6a4
#define PLLA1_MISC0 0x6a8
#define PLLA1_MISC1 0x6ac
@@ -367,12 +367,12 @@ static const char *mux_pllmcp_clkm[] = {
/* PLLMB */
#define PLLMB_BASE_LOCK (1 << 27)
-#define PLLMB_MISC0_LOCK_OVERRIDE (1 << 18)
-#define PLLMB_MISC0_IDDQ (1 << 17)
-#define PLLMB_MISC0_LOCK_ENABLE (1 << 16)
+#define PLLMB_MISC1_LOCK_OVERRIDE (1 << 18)
+#define PLLMB_MISC1_IDDQ (1 << 17)
+#define PLLMB_MISC1_LOCK_ENABLE (1 << 16)
-#define PLLMB_MISC0_DEFAULT_VALUE 0x00030000
-#define PLLMB_MISC0_WRITE_MASK 0x0007ffff
+#define PLLMB_MISC1_DEFAULT_VALUE 0x00030000
+#define PLLMB_MISC1_WRITE_MASK 0x0007ffff
/* PLLP */
#define PLLP_BASE_OVERRIDE (1 << 28)
@@ -914,15 +914,15 @@ void tegra210_pllmb_set_defaults(struct tegra_clk_pll *pllmb)
* PLL is ON: check if defaults already set, then set those
* that can be updated in flight.
*/
- val = PLLMB_MISC0_DEFAULT_VALUE & (~PLLMB_MISC0_IDDQ);
- mask = PLLMB_MISC0_LOCK_ENABLE | PLLMB_MISC0_LOCK_OVERRIDE;
+ val = PLLMB_MISC1_DEFAULT_VALUE & (~PLLMB_MISC1_IDDQ);
+ mask = PLLMB_MISC1_LOCK_ENABLE | PLLMB_MISC1_LOCK_OVERRIDE;
_pll_misc_chk_default(clk_base, pllmb->params, 0, val,
- ~mask & PLLMB_MISC0_WRITE_MASK);
+ ~mask & PLLMB_MISC1_WRITE_MASK);
/* Enable lock detect */
val = readl_relaxed(clk_base + pllmb->params->ext_misc_reg[0]);
val &= ~mask;
- val |= PLLMB_MISC0_DEFAULT_VALUE & mask;
+ val |= PLLMB_MISC1_DEFAULT_VALUE & mask;
writel_relaxed(val, clk_base + pllmb->params->ext_misc_reg[0]);
udelay(1);
@@ -930,7 +930,7 @@ void tegra210_pllmb_set_defaults(struct tegra_clk_pll *pllmb)
}
/* set IDDQ, enable lock detect */
- writel_relaxed(PLLMB_MISC0_DEFAULT_VALUE,
+ writel_relaxed(PLLMB_MISC1_DEFAULT_VALUE,
clk_base + pllmb->params->ext_misc_reg[0]);
udelay(1);
}
@@ -1557,14 +1557,14 @@ static struct tegra_clk_pll_params pll_m_params = {
.vco_min = 800000000,
.vco_max = 1866000000,
.base_reg = PLLM_BASE,
- .misc_reg = PLLM_MISC0,
+ .misc_reg = PLLM_MISC2,
.lock_mask = PLL_BASE_LOCK,
.lock_enable_bit_idx = PLLM_MISC_LOCK_ENABLE,
.lock_delay = 300,
- .iddq_reg = PLLM_MISC0,
+ .iddq_reg = PLLM_MISC2,
.iddq_bit_idx = PLLM_IDDQ_BIT,
.max_p = PLL_QLIN_PDIV_MAX,
- .ext_misc_reg[0] = PLLM_MISC0,
+ .ext_misc_reg[0] = PLLM_MISC2,
.ext_misc_reg[0] = PLLM_MISC1,
.round_p_to_pdiv = pll_qlin_p_to_pdiv,
.pdiv_tohw = pll_qlin_pdiv_to_hw,
@@ -1584,13 +1584,13 @@ static struct tegra_clk_pll_params pll_mb_params = {
.vco_min = 800000000,
.vco_max = 1866000000,
.base_reg = PLLMB_BASE,
- .misc_reg = PLLMB_MISC0,
+ .misc_reg = PLLMB_MISC1,
.lock_mask = PLL_BASE_LOCK,
.lock_delay = 300,
- .iddq_reg = PLLMB_MISC0,
+ .iddq_reg = PLLMB_MISC1,
.iddq_bit_idx = PLLMB_IDDQ_BIT,
.max_p = PLL_QLIN_PDIV_MAX,
- .ext_misc_reg[0] = PLLMB_MISC0,
+ .ext_misc_reg[0] = PLLMB_MISC1,
.round_p_to_pdiv = pll_qlin_p_to_pdiv,
.pdiv_tohw = pll_qlin_pdiv_to_hw,
.div_nmp = &pllm_nmp,
--
1.9.1
When adding the nvenc clock, it was partially named msenc in
the code. Since the msenc clk isn't present in T210 where the nvenc
clk is, its misleading to see it present. Therefore, properly
rename it.
Signed-off-by: Rhyland Klein <[email protected]>
---
drivers/clk/tegra/clk-tegra-periph.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/clk/tegra/clk-tegra-periph.c b/drivers/clk/tegra/clk-tegra-periph.c
index 105405ca85ab..1860df1862dd 100644
--- a/drivers/clk/tegra/clk-tegra-periph.c
+++ b/drivers/clk/tegra/clk-tegra-periph.c
@@ -773,7 +773,7 @@ static struct tegra_periph_init_data periph_clks[] = {
XUSB("xusb_dev_src", mux_clkm_pllp_pllc_pllre, CLK_SOURCE_XUSB_DEV_SRC, 95, TEGRA_PERIPH_ON_APB | TEGRA_PERIPH_NO_RESET, tegra_clk_xusb_dev_src),
XUSB("xusb_dev_src", mux_clkm_pllp_pllre, CLK_SOURCE_XUSB_DEV_SRC, 95, TEGRA_PERIPH_ON_APB | TEGRA_PERIPH_NO_RESET, tegra_clk_xusb_dev_src_8),
MUX8("dbgapb", mux_pllp_clkm_2, CLK_SOURCE_DBGAPB, 185, TEGRA_PERIPH_NO_RESET, tegra_clk_dbgapb),
- MUX8("msenc", mux_pllc2_c_c3_pllp_plla1_clkm, CLK_SOURCE_NVENC, 219, 0, tegra_clk_nvenc),
+ MUX8("nvenc", mux_pllc2_c_c3_pllp_plla1_clkm, CLK_SOURCE_NVENC, 219, 0, tegra_clk_nvenc),
MUX8("nvdec", mux_pllc2_c_c3_pllp_plla1_clkm, CLK_SOURCE_NVDEC, 194, 0, tegra_clk_nvdec),
MUX8("nvjpg", mux_pllc2_c_c3_pllp_plla1_clkm, CLK_SOURCE_NVJPG, 195, 0, tegra_clk_nvjpg),
MUX8("ape", mux_plla_pllc4_out0_pllc_pllc4_out1_pllp_pllc4_out2_clkm, CLK_SOURCE_APE, 198, TEGRA_PERIPH_ON_APB, tegra_clk_ape),
--
1.9.1
From: Andrew Bresticker <[email protected]>
Since the ->enable() callback is called with a spinlock held, we cannot
call potentially blocking functions such as clk_get_rate() or
clk_get_parent(), so use the unlocked versions instead.
Signed-off-by: Andrew Bresticker <[email protected]>
[rklein: Adapted from ChromeOS patch, removing pllu_enable cleanup as
it isn't present upstream]
Signed-off-by: Rhyland Klein <[email protected]>
---
drivers/clk/tegra/clk-pll.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/clk/tegra/clk-pll.c b/drivers/clk/tegra/clk-pll.c
index a534bfab30b3..65156486889a 100644
--- a/drivers/clk/tegra/clk-pll.c
+++ b/drivers/clk/tegra/clk-pll.c
@@ -880,7 +880,7 @@ static int clk_plle_training(struct tegra_clk_pll *pll)
static int clk_plle_enable(struct clk_hw *hw)
{
struct tegra_clk_pll *pll = to_clk_pll(hw);
- unsigned long input_rate = clk_get_rate(clk_get_parent(hw->clk));
+ unsigned long input_rate = clk_hw_get_rate(clk_hw_get_parent(hw));
struct tegra_clk_pll_freq_table sel;
u32 val;
int err;
@@ -1378,7 +1378,7 @@ static int clk_plle_tegra114_enable(struct clk_hw *hw)
u32 val;
int ret;
unsigned long flags = 0;
- unsigned long input_rate = clk_get_rate(clk_get_parent(hw->clk));
+ unsigned long input_rate = clk_hw_get_rate(clk_hw_get_parent(hw));
if (_get_table_rate(hw, &sel, pll->params->fixed_rate, input_rate))
return -EINVAL;
@@ -2014,7 +2014,7 @@ static int clk_plle_tegra210_enable(struct clk_hw *hw)
u32 val;
int ret;
unsigned long flags = 0;
- unsigned long input_rate = clk_get_rate(clk_get_parent(hw->clk));
+ unsigned long input_rate = clk_hw_get_rate(clk_hw_get_parent(hw));
if (_get_table_rate(hw, &sel, pll->params->fixed_rate, input_rate))
return -EINVAL;
--
1.9.1
The logic for calculating the input rate used when figuring out
the proper dynamic steps for pllx was incorrect. It is supposed to
be calculated using parent_rate / m but it was just using the parent
rate directly, therefore using the wrong step values.
Signed-off-by: Rhyland Klein <[email protected]>
---
drivers/clk/tegra/clk-tegra210.c | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/drivers/clk/tegra/clk-tegra210.c b/drivers/clk/tegra/clk-tegra210.c
index 2a7faa357130..5d8fac7052f2 100644
--- a/drivers/clk/tegra/clk-tegra210.c
+++ b/drivers/clk/tegra/clk-tegra210.c
@@ -780,13 +780,13 @@ static void pllx_get_dyn_steps(struct clk_hw *hw, u32 *step_a, u32 *step_b)
{
unsigned long input_rate;
- if (!IS_ERR_OR_NULL(hw->clk)) {
+ /* cf rate */
+ if (!IS_ERR_OR_NULL(hw->clk))
input_rate = clk_hw_get_rate(clk_hw_get_parent(hw));
- /* cf rate */
- input_rate /= tegra_pll_get_fixed_mdiv(hw, input_rate);
- } else {
+ else
input_rate = 38400000;
- }
+
+ input_rate /= tegra_pll_get_fixed_mdiv(hw, input_rate);
switch (input_rate) {
case 12000000:
--
1.9.1
From: Mark Kuo <[email protected]>
SW should not disable PLLE if PLLE is already put under HW control.
Signed-off-by: Mark Kuo <[email protected]>
Signed-off-by: Rhyland Klein <[email protected]>
---
drivers/clk/tegra/clk-pll.c | 22 +++++++++++++++-------
1 file changed, 15 insertions(+), 7 deletions(-)
diff --git a/drivers/clk/tegra/clk-pll.c b/drivers/clk/tegra/clk-pll.c
index 65156486889a..d9c3109b75bd 100644
--- a/drivers/clk/tegra/clk-pll.c
+++ b/drivers/clk/tegra/clk-pll.c
@@ -2012,7 +2012,7 @@ static int clk_plle_tegra210_enable(struct clk_hw *hw)
struct tegra_clk_pll *pll = to_clk_pll(hw);
struct tegra_clk_pll_freq_table sel;
u32 val;
- int ret;
+ int ret = 0;
unsigned long flags = 0;
unsigned long input_rate = clk_hw_get_rate(clk_hw_get_parent(hw));
@@ -2022,16 +2022,14 @@ static int clk_plle_tegra210_enable(struct clk_hw *hw)
if (pll->lock)
spin_lock_irqsave(pll->lock, flags);
+ val = pll_readl(pll->params->aux_reg, pll);
+ if (val & PLLE_AUX_SEQ_ENABLE)
+ goto out;
+
val = pll_readl_base(pll);
val &= ~BIT(30); /* Disable lock override */
pll_writel_base(val, pll);
- val = pll_readl(pll->params->aux_reg, pll);
- val |= PLLE_AUX_ENABLE_SWCTL;
- val &= ~PLLE_AUX_SEQ_ENABLE;
- pll_writel(val, pll->params->aux_reg, pll);
- udelay(1);
-
val = pll_readl_misc(pll);
val |= PLLE_MISC_LOCK_ENABLE;
val |= PLLE_MISC_IDDQ_SW_CTRL;
@@ -2104,15 +2102,25 @@ static void clk_plle_tegra210_disable(struct clk_hw *hw)
if (pll->lock)
spin_lock_irqsave(pll->lock, flags);
+ /* If PLLE HW sequencer is enabled, SW should not disable PLLE */
+ val = pll_readl(pll->params->aux_reg, pll);
+ if (val & PLLE_AUX_SEQ_ENABLE)
+ goto out;
+
val = pll_readl_base(pll);
val &= ~PLLE_BASE_ENABLE;
pll_writel_base(val, pll);
+ val = pll_readl(pll->params->aux_reg, pll);
+ val |= PLLE_AUX_ENABLE_SWCTL | PLLE_AUX_SS_SWCTL;
+ pll_writel(val, pll->params->aux_reg, pll);
+
val = pll_readl_misc(pll);
val |= PLLE_MISC_IDDQ_SW_CTRL | PLLE_MISC_IDDQ_SW_VALUE;
pll_writel_misc(val, pll);
udelay(1);
+out:
if (pll->lock)
spin_unlock_irqrestore(pll->lock, flags);
}
--
1.9.1
From: Mark Kuo <[email protected]>
Fix PLLE spread spectrum configuration so it aligns with downstream
kernel.
Signed-off-by: Mark Kuo <[email protected]>
Signed-off-by: Rhyland Klein <[email protected]>
---
drivers/clk/tegra/clk-pll.c | 22 ++++++++++++++--------
1 file changed, 14 insertions(+), 8 deletions(-)
diff --git a/drivers/clk/tegra/clk-pll.c b/drivers/clk/tegra/clk-pll.c
index d9c3109b75bd..6ac3f843e7ca 100644
--- a/drivers/clk/tegra/clk-pll.c
+++ b/drivers/clk/tegra/clk-pll.c
@@ -86,15 +86,21 @@
#define PLLE_SS_DISABLE (PLLE_SS_CNTL_BYPASS_SS | PLLE_SS_CNTL_INTERP_RESET |\
PLLE_SS_CNTL_SSC_BYP)
#define PLLE_SS_MAX_MASK 0x1ff
-#define PLLE_SS_MAX_VAL 0x25
+#define PLLE_SS_MAX_VAL_TEGRA114 0x25
+#define PLLE_SS_MAX_VAL_TEGRA210 0x21
#define PLLE_SS_INC_MASK (0xff << 16)
#define PLLE_SS_INC_VAL (0x1 << 16)
#define PLLE_SS_INCINTRV_MASK (0x3f << 24)
-#define PLLE_SS_INCINTRV_VAL (0x20 << 24)
+#define PLLE_SS_INCINTRV_VAL_TEGRA114 (0x20 << 24)
+#define PLLE_SS_INCINTRV_VAL_TEGRA210 (0x23 << 24)
#define PLLE_SS_COEFFICIENTS_MASK \
(PLLE_SS_MAX_MASK | PLLE_SS_INC_MASK | PLLE_SS_INCINTRV_MASK)
-#define PLLE_SS_COEFFICIENTS_VAL \
- (PLLE_SS_MAX_VAL | PLLE_SS_INC_VAL | PLLE_SS_INCINTRV_VAL)
+#define PLLE_SS_COEFFICIENTS_VAL_TEGRA114 \
+ (PLLE_SS_MAX_VAL_TEGRA114 | PLLE_SS_INC_VAL |\
+ PLLE_SS_INCINTRV_VAL_TEGRA114)
+#define PLLE_SS_COEFFICIENTS_VAL_TEGRA210 \
+ (PLLE_SS_MAX_VAL_TEGRA210 | PLLE_SS_INC_VAL |\
+ PLLE_SS_INCINTRV_VAL_TEGRA210)
#define PLLE_AUX_PLLP_SEL BIT(2)
#define PLLE_AUX_USE_LOCKDET BIT(3)
@@ -1401,7 +1407,7 @@ static int clk_plle_tegra114_enable(struct clk_hw *hw)
val |= PLLE_MISC_IDDQ_SW_CTRL;
val &= ~PLLE_MISC_IDDQ_SW_VALUE;
val |= PLLE_MISC_PLLE_PTS;
- val |= PLLE_MISC_VREG_BG_CTRL_MASK | PLLE_MISC_VREG_CTRL_MASK;
+ val &= ~(PLLE_MISC_VREG_BG_CTRL_MASK | PLLE_MISC_VREG_CTRL_MASK);
pll_writel_misc(val, pll);
udelay(5);
@@ -1428,7 +1434,7 @@ static int clk_plle_tegra114_enable(struct clk_hw *hw)
val = pll_readl(PLLE_SS_CTRL, pll);
val &= ~(PLLE_SS_CNTL_CENTER | PLLE_SS_CNTL_INVERT);
val &= ~PLLE_SS_COEFFICIENTS_MASK;
- val |= PLLE_SS_COEFFICIENTS_VAL;
+ val |= PLLE_SS_COEFFICIENTS_VAL_TEGRA114;
pll_writel(val, PLLE_SS_CTRL, pll);
val &= ~(PLLE_SS_CNTL_SSC_BYP | PLLE_SS_CNTL_BYPASS_SS);
pll_writel(val, PLLE_SS_CTRL, pll);
@@ -2035,7 +2041,7 @@ static int clk_plle_tegra210_enable(struct clk_hw *hw)
val |= PLLE_MISC_IDDQ_SW_CTRL;
val &= ~PLLE_MISC_IDDQ_SW_VALUE;
val |= PLLE_MISC_PLLE_PTS;
- val |= PLLE_MISC_VREG_BG_CTRL_MASK | PLLE_MISC_VREG_CTRL_MASK;
+ val &= ~(PLLE_MISC_VREG_BG_CTRL_MASK | PLLE_MISC_VREG_CTRL_MASK);
pll_writel_misc(val, pll);
udelay(5);
@@ -2065,7 +2071,7 @@ static int clk_plle_tegra210_enable(struct clk_hw *hw)
val = pll_readl(PLLE_SS_CTRL, pll);
val &= ~(PLLE_SS_CNTL_CENTER | PLLE_SS_CNTL_INVERT);
val &= ~PLLE_SS_COEFFICIENTS_MASK;
- val |= PLLE_SS_COEFFICIENTS_VAL;
+ val |= PLLE_SS_COEFFICIENTS_VAL_TEGRA210;
pll_writel(val, PLLE_SS_CTRL, pll);
val &= ~(PLLE_SS_CNTL_SSC_BYP | PLLE_SS_CNTL_BYPASS_SS);
pll_writel(val, PLLE_SS_CTRL, pll);
--
1.9.1
Initialize PLL_D2 to a sane rate at the start of the day.
Signed-off-by: Rhyland Klein <[email protected]>
---
drivers/clk/tegra/clk-tegra210.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/clk/tegra/clk-tegra210.c b/drivers/clk/tegra/clk-tegra210.c
index 5d8fac7052f2..cc560a1f6efb 100644
--- a/drivers/clk/tegra/clk-tegra210.c
+++ b/drivers/clk/tegra/clk-tegra210.c
@@ -2749,6 +2749,7 @@ static struct tegra_clk_init_table init_table[] __initdata = {
{ TEGRA210_CLK_PLL_DP, TEGRA210_CLK_CLK_MAX, 270000000, 0 },
{ TEGRA210_CLK_SOC_THERM, TEGRA210_CLK_PLL_P, 51000000, 0 },
{ TEGRA210_CLK_CCLK_G, TEGRA210_CLK_CLK_MAX, 0, 1 },
+ { TEGRA210_CLK_PLL_D2, TEGRA210_CLK_CLK_MAX, 594000000, 0 },
/* This MUST be the last entry. */
{ TEGRA210_CLK_CLK_MAX, TEGRA210_CLK_CLK_MAX, 0, 0 },
};
--
1.9.1