- The DMA error interrupt bit is in a different position as
compared to the sdhci standard. This is accounted for in
many cases, but not handled in the case of clearing the
INT_STATUS register by writing a 1 to that location.
- The HOST_CONTROL register is very different as compared to
the sdhci standard. This is accounted for in the write
case, but not when read back out (which it is in the sdhci
code).
Signed-off-by: Dave Russell <[email protected]>
Signed-off-by: Aaron Brice <[email protected]>
---
drivers/mmc/host/sdhci-esdhc-imx.c | 23 ++++++++++++++++++++++-
1 file changed, 22 insertions(+), 1 deletion(-)
diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
index 1f54fd8..d61ef16 100644
--- a/drivers/mmc/host/sdhci-esdhc-imx.c
+++ b/drivers/mmc/host/sdhci-esdhc-imx.c
@@ -346,7 +346,8 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
u32 data;
- if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE)) {
+ if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE ||
+ reg == SDHCI_INT_STATUS)) {
if ((val & SDHCI_INT_CARD_INT) && !esdhc_is_usdhc(imx_data)) {
/*
* Clear and then set D3CD bit to avoid missing the
@@ -555,6 +556,25 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
esdhc_clrset_le(host, 0xffff, val, reg);
}
+static u8 esdhc_readb_le(struct sdhci_host *host, int reg)
+{
+ u8 ret;
+ u32 long_val;
+
+ switch (reg) {
+ case SDHCI_HOST_CONTROL:
+ long_val = readl(host->ioaddr + reg);
+
+ ret = long_val & SDHCI_CTRL_LED;
+ ret |= (long_val >> 5) & SDHCI_CTRL_DMA_MASK;
+ ret |= (long_val & ESDHC_CTRL_4BITBUS);
+ ret |= (long_val & ESDHC_CTRL_8BITBUS) << 3;
+ return ret;
+ }
+
+ return readb(host->ioaddr + reg);
+}
+
static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg)
{
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
@@ -947,6 +967,7 @@ static void esdhc_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
static struct sdhci_ops sdhci_esdhc_ops = {
.read_l = esdhc_readl_le,
.read_w = esdhc_readw_le,
+ .read_b = esdhc_readb_le,
.write_l = esdhc_writel_le,
.write_w = esdhc_writew_le,
.write_b = esdhc_writeb_le,
--
2.7.4
On Fri, Oct 7, 2016 at 6:54 AM, Aaron Brice <[email protected]> wrote:
> - The DMA error interrupt bit is in a different position as
> compared to the sdhci standard. This is accounted for in
> many cases, but not handled in the case of clearing the
> INT_STATUS register by writing a 1 to that location.
> - The HOST_CONTROL register is very different as compared to
> the sdhci standard. This is accounted for in the write
> case, but not when read back out (which it is in the sdhci
> code).
>
> Signed-off-by: Dave Russell <[email protected]>
> Signed-off-by: Aaron Brice <[email protected]>
> ---
> drivers/mmc/host/sdhci-esdhc-imx.c | 23 ++++++++++++++++++++++-
> 1 file changed, 22 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
> index 1f54fd8..d61ef16 100644
> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> @@ -346,7 +346,8 @@ static void esdhc_writel_le(struct sdhci_host *host, u32 val, int reg)
> struct pltfm_imx_data *imx_data = sdhci_pltfm_priv(pltfm_host);
> u32 data;
>
> - if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE)) {
> + if (unlikely(reg == SDHCI_INT_ENABLE || reg == SDHCI_SIGNAL_ENABLE ||
> + reg == SDHCI_INT_STATUS)) {
> if ((val & SDHCI_INT_CARD_INT) && !esdhc_is_usdhc(imx_data)) {
> /*
> * Clear and then set D3CD bit to avoid missing the
> @@ -555,6 +556,25 @@ static void esdhc_writew_le(struct sdhci_host *host, u16 val, int reg)
> esdhc_clrset_le(host, 0xffff, val, reg);
> }
>
> +static u8 esdhc_readb_le(struct sdhci_host *host, int reg)
> +{
> + u8 ret;
> + u32 long_val;
> +
> + switch (reg) {
> + case SDHCI_HOST_CONTROL:
> + long_val = readl(host->ioaddr + reg);
> +
> + ret = long_val & SDHCI_CTRL_LED;
> + ret |= (long_val >> 5) & SDHCI_CTRL_DMA_MASK;
> + ret |= (long_val & ESDHC_CTRL_4BITBUS);
> + ret |= (long_val & ESDHC_CTRL_8BITBUS) << 3;
> + return ret;
Thanks for the effort.
One nitpick: would be more like to use 'val' instead of 'long_val' to
be consistent with exist using.
(i saw a few 'new_val' as well, maybe we could clean up them in the future,
but at least we could avoid inventing more from now)
Otherwise,
Acked-by: Dong Aisheng <[email protected]>
Regards
Dong Aisheng
> + }
> +
> + return readb(host->ioaddr + reg);
> +}
> +
> static void esdhc_writeb_le(struct sdhci_host *host, u8 val, int reg)
> {
> struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> @@ -947,6 +967,7 @@ static void esdhc_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
> static struct sdhci_ops sdhci_esdhc_ops = {
> .read_l = esdhc_readl_le,
> .read_w = esdhc_readw_le,
> + .read_b = esdhc_readb_le,
> .write_l = esdhc_writel_le,
> .write_w = esdhc_writew_le,
> .write_b = esdhc_writeb_le,
> --
> 2.7.4
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> [email protected]
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel