Hello all,
Using 2.2.19pre14 with:
* software raid
* raid1 readbalancing
* i2c
* lm_sensors
* ipsec
My drives are as follows:
hda: QUANTUM FIREBALLP AS20.5, 19595MB w/1902kB Cache, CHS=2498/255/63
hdc: QUANTUM FIREBALLP AS20.5, 19595MB w/1902kB Cache, CHS=39813/16/63
hdd: IBM-DTTA-350840, 8063MB w/467kB Cache, CHS=16383/16/63
hdb: ATAPI 4X CD-ROM drive, 256kB Cache
[ Bios sees: HDA & HDC : udma5, HDD: udma2 ]
And the mainboard related stuff in lspci:
00:00.0 Host bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3] (rev 04)
00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP]
00:07.0 ISA bridge: VIA Technologies, Inc. VT82C586/A/B PCI-to-ISA [Apollo VP] (rev 47)
00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 06)
00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 02)
00:07.3 Bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
Now, if I turn on dma on hdd, and run hdparm benchmark, everything works
fine.
If I turn on dma with hdparm on hda or hdc, next disk activity will freeze
the system completely. No keyboard interaction, not anything. Only reset
helps.
Also, if I disable UDMA in bios completely on hda and hdc, hdparm will
work, but the speed is awful (only ~6 MB/s) even if DMA is enabled.
The most relevant kernel settings are, I think:
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_BLK_DEV_OFFBOARD is not set
CONFIG_IDEDMA_AUTO=y
# CONFIG_BLK_DEV_OPTI621 is not set
# CONFIG_BLK_DEV_ALI15X3 is not set
# CONFIG_BLK_DEV_TRM290 is not set
# CONFIG_BLK_DEV_NS87415 is not set
CONFIG_BLK_DEV_VIA82C586=y
# CONFIG_BLK_DEV_CMD646 is not set
# CONFIG_BLK_DEV_CS5530 is not set
# CONFIG_IDE_CHIPSETS is not set
Any ideas?
Please Cc:
--
Pekka Savola "Tell me of difficulties surmounted,
Netcore Oy not those you stumble over and fall"
Systems. Networks. Security. -- Robert Jordan: A Crown of Swords
On Sat, 24 Feb 2001, Pekka Savola wrote:
There was a suggestion to try the IDE patch. With it, the same kind of
freezing happens immediately after 'hdparm -d 1'.
With the patch, the kernel message at bootup is like:
hda: QUANTUM FIREBALLP AS20.5, 19595MB w/1902kB Cache, CHS=2498/255/63
hdc: QUANTUM FIREBALLP AS20.5, 19595MB w/1902kB Cache, CHS=39813/16/63
hdd: IBM-DTTA-350840, 8063MB w/467kB Cache, CHS=16383/16/63, UDMA(33)
hdb: ATAPI 4X CD-ROM drive, 256kB Cache
So, it'd appear Fireballs don't get UDMA enabled for some reason.
In the patch there are a few shit-listed drives:
---
const char *quirk_drives[] = {
"QUANTUM FIREBALLlct08 08",
"QUANTUM FIREBALLP KA6.4",
"QUANTUM FIREBALLP LM20.4",
"QUANTUM FIREBALLP LM20.5",
NULL
};
---
However, this is FIREBALLP AS20.5, not LM20.5.
Any idea why DMA doesn't get on ?
> Hello all,
>
> Using 2.2.19pre14 with:
> * software raid
> * raid1 readbalancing
> * i2c
> * lm_sensors
> * ipsec
>
> My drives are as follows:
>
> hda: QUANTUM FIREBALLP AS20.5, 19595MB w/1902kB Cache, CHS=2498/255/63
> hdc: QUANTUM FIREBALLP AS20.5, 19595MB w/1902kB Cache, CHS=39813/16/63
> hdd: IBM-DTTA-350840, 8063MB w/467kB Cache, CHS=16383/16/63
> hdb: ATAPI 4X CD-ROM drive, 256kB Cache
>
> [ Bios sees: HDA & HDC : udma5, HDD: udma2 ]
>
> And the mainboard related stuff in lspci:
>
> 00:00.0 Host bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3] (rev 04)
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598 [Apollo MVP3 AGP]
> 00:07.0 ISA bridge: VIA Technologies, Inc. VT82C586/A/B PCI-to-ISA [Apollo VP] (rev 47)
> 00:07.1 IDE interface: VIA Technologies, Inc. VT82C586 IDE [Apollo] (rev 06)
> 00:07.2 USB Controller: VIA Technologies, Inc. VT82C586B USB (rev 02)
> 00:07.3 Bridge: VIA Technologies, Inc. VT82C586B ACPI (rev 10)
>
> Now, if I turn on dma on hdd, and run hdparm benchmark, everything works
> fine.
>
> If I turn on dma with hdparm on hda or hdc, next disk activity will freeze
> the system completely. No keyboard interaction, not anything. Only reset
> helps.
>
> Also, if I disable UDMA in bios completely on hda and hdc, hdparm will
> work, but the speed is awful (only ~6 MB/s) even if DMA is enabled.
>
> The most relevant kernel settings are, I think:
>
> CONFIG_BLK_DEV_IDEDMA=y
> # CONFIG_BLK_DEV_OFFBOARD is not set
> CONFIG_IDEDMA_AUTO=y
> # CONFIG_BLK_DEV_OPTI621 is not set
> # CONFIG_BLK_DEV_ALI15X3 is not set
> # CONFIG_BLK_DEV_TRM290 is not set
> # CONFIG_BLK_DEV_NS87415 is not set
> CONFIG_BLK_DEV_VIA82C586=y
> # CONFIG_BLK_DEV_CMD646 is not set
> # CONFIG_BLK_DEV_CS5530 is not set
> # CONFIG_IDE_CHIPSETS is not set
>
> Any ideas?
>
> Please Cc:
>
--
Pekka Savola "Tell me of difficulties surmounted,
Netcore Oy not those you stumble over and fall"
Systems. Networks. Security. -- Robert Jordan: A Crown of Swords