I plug in usb devices and nothing shows up. I reboot the system with the
devices attached, nothing shows up. If I modeprobe ov511 nothing. If I
modrobe usb-storage nothing. I am using the standard kernel with -aa5
patchset and supermount-ng. I tried going back to 2.6.5, 2.6.4, and 2.6.3
without the patches, the same problem. USB worked under 2.4.25. Any ideas
and suggestions would be helpful, if more information is needed, please let
me know and I will provide it.
Here is the data.
cat /proc/interrrupts - output
CPU0 CPU1
0: 139683637 37 IO-APIC-edge timer
1: 510 1 IO-APIC-edge i8042
2: 0 0 XT-PIC cascade
3: 94944 1 IO-APIC-edge serial
4: 168 1 IO-APIC-edge serial
7: 0 0 IO-APIC-edge parport0
8: 0 1 IO-APIC-edge rtc
9: 466512 0 IO-APIC-level megaraid
11: 1163951 1 IO-APIC-level eth0, eth1, eth2, eth3
15: 24533 1 IO-APIC-level aic7xxx, aic7xxx
NMI: 139683139 139683025
LOC: 139689481 139689629
ERR: 0
MIS: 0
lspci - output
00:13.0 USB Controller: OPTi Inc. 82C861 (rev 10)
00:13.0 USB Controller: OPTi Inc. 82C861 (rev 10) (prog-if 10 [OHCI])
Subsystem: OPTi Inc. 82C861
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, cache line size 08
Interrupt: pin A routed to IRQ 14
Region 0: Memory at fdfff000 (32-bit, non-prefetchable) [size=4K]
ls /sys/bus/usb/devices - output
[blank]
ls /sys/bus/usb/drivers - output
hub usb usbfs
syslog - output
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
USB Universal Host Controller Interface driver v2.2
linux_ver - output
Linux server 2.6.5-lfs-3 #1 SMP Sat Apr 10 20:25:01 PDT 2004 i686 pentium2
i386 GNU/Linux
Gnu C 3.3.3
Gnu make 3.80
binutils 2.15.90.0.1.1
util-linux 2.12a
mount 2.12a
module-init-tools 3.0
e2fsprogs 1.35
PPP 2.4.2
nfs-utils 1.0.6
Linux C Library 2.3.3
Dynamic linker (ldd) 2.3.3
Linux C++ Library 5.0.5
Procps 3.2.1
Net-tools 1.60
Kbd 1.12
Sh-utils 5.2.1
Modules Loaded uhci_hcd usbcore videodev hfs vfat fat isofs
zlib_inflate floppy ext2 nfsd exportfs lockd sunrpc parport_pc lp parport
ipt_TOS ipt_TCPMSS ipt_state ipt_REJECT ipt_LOG ipt_limit iptable_mangle
iptable_nat ip_conntrack_irc ip_conntrack_ftp ip_conntrack iptable_filter
ip_tables af_packet bonding 8250 serial_core tulip crc32 rtc supermount unix
aic7xxx megaraid sd_mod scsi_mod
Config file is attached
----
Jim Gifford
[email protected]
On Mon, Apr 12, 2004 at 04:24:07PM -0700, Jim Gifford wrote:
> cat /proc/interrrupts - output
>
> CPU0 CPU1
> 0: 139683637 37 IO-APIC-edge timer
> 1: 510 1 IO-APIC-edge i8042
> 2: 0 0 XT-PIC cascade
> 3: 94944 1 IO-APIC-edge serial
> 4: 168 1 IO-APIC-edge serial
> 7: 0 0 IO-APIC-edge parport0
> 8: 0 1 IO-APIC-edge rtc
> 9: 466512 0 IO-APIC-level megaraid
> 11: 1163951 1 IO-APIC-level eth0, eth1, eth2, eth3
> 15: 24533 1 IO-APIC-level aic7xxx, aic7xxx
Hm, no usb driver there...
> 00:13.0 USB Controller: OPTi Inc. 82C861 (rev 10) (prog-if 10 [OHCI])
Looks like a OHCI controller...
> Modules Loaded uhci_hcd usbcore videodev hfs vfat fat isofs
> zlib_inflate floppy ext2 nfsd exportfs lockd sunrpc parport_pc lp parport
> ipt_TOS ipt_TCPMSS ipt_state ipt_REJECT ipt_LOG ipt_limit iptable_mangle
> iptable_nat ip_conntrack_irc ip_conntrack_ftp ip_conntrack iptable_filter
> ip_tables af_packet bonding 8250 serial_core tulip crc32 rtc supermount unix
> aic7xxx megaraid sd_mod scsi_mod
Yup, no ohci module either. How about building the usb ohci module
(ohci-hcd) and trying that? It should fix your problem.
Hope this helps,
greg k-h