Linux version 2.6.14-rc3 (root@abg4507s) (gcc version 3.3.3 (SuSE Linux)) #1 SMP Tue Oct 11 11:34:10 CEST 2005
... snip ...
SCSI subsystem initialized
Fusion MPT base driver 3.03.03
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SPI Host driver 3.03.03
ACPI: PCI Interrupt 0000:02:08.0[A] -> GSI 24 (level, low) -> IRQ 19
mptbase: Initiating ioc0 bringup
ioc0: 53C1030: Capabilities={Initiator}
scsi0 : ioc0: LSI53C1030, FwRev=01032571h, Ports=1, MaxQ=222, IRQ=19
Vendor: LSILOGIC Model: 1030 IM Rev: 1000
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 142131200 512-byte hdwr sectors (72771 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 142131200 512-byte hdwr sectors (72771 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: SDR Model: GEM318P Rev: 1
Type: Processor ANSI SCSI revision: 02
ACPI: PCI Interrupt 0000:02:08.1[B] -> GSI 25 (level, low) -> IRQ 20
mptbase: Initiating ioc1 bringup
mptscsih: ioc0: DV: Release failed. id 0<6>ioc1: 53C1030: Capabilities={Initiator}
scsi1 : ioc1: LSI53C1030, FwRev=01032571h, Ports=1, MaxQ=222, IRQ=20
mptscsih: ioc0: attempting task abort! (sc=f748b380)
scsi0 : destination target 0, lun 0
command: Read (10): 28 00 00 80 34 4d 00 00 02 00
mptscsih: ioc0: task abort: SUCCESS (sc=f748b380)
mptscsih: ioc0: attempting task abort! (sc=f748b380)
scsi0 : destination target 0, lun 0
command: Test Unit Ready: 00 00 00 00 00 00
mptscsih: ioc0: task abort: SUCCESS (sc=f748b380)
mptscsih: ioc0: attempting target reset! (sc=f748b380)
scsi0 : destination target 0, lun 0
command: Read (10): 28 00 00 80 34 4d 00 00 02 00
mptbase: ioc0: IOCStatus(0x0048): SCSI Task Terminated
mptbase: ioc0: IOCStatus(0x0048): SCSI Task Terminated
mptscsih: ioc0: target reset: SUCCESS (sc=f748b380)
mptscsih: ioc0: attempting task abort! (sc=f748b380)
scsi0 : destination target 0, lun 0
command: Test Unit Ready: 00 00 00 00 00 00
mptscsih: ioc0: task abort: SUCCESS (sc=f748b380)
mptscsih: ioc0: attempting bus reset! (sc=f748b380)
scsi0 : destination target 0, lun 0
command: Read (10): 28 00 00 80 34 4d 00 00 02 00
mptbase: ioc0: IOCStatus(0x0048): SCSI Task Terminated
mptscsih: ioc0: bus reset: SUCCESS (sc=f748b380)
mptscsih: ioc0: attempting task abort! (sc=f748b380)
scsi0 : destination target 0, lun 0
command: Test Unit Ready: 00 00 00 00 00 00
mptscsih: ioc0: task abort: SUCCESS (sc=f748b380)
mptscsih: ioc0: Attempting host reset! (sc=f748b380)
mptbase: Initiating ioc0 recovery
EXT2-fs warning (device sda2): ext2_fill_super: mounting ext3 filesystem as ext2
... snip ... (now the system runs fine! AFAICS ...)