changes v9:
- rebase against kernel v5.8-rc3
- prti6q: set index to default-brightness-level
- prti6q: remove regulator-always-on
- prti6q: rename mux_ssi1 and mux_pins3 to mux-ssi1, mux-pins3
- prti6q: move can1 node out of dtsi and fix alphabetical order
- prti6q: fix reg value for rgmii_phy
- prti6q: fix pinctrl_can2 and pinctrl_can1
- vt7: fix fsl,mode
- vt7: rename mux_ssi1 and mux_pins3 to mux-ssi1, mux-pins3
- vt7: remove regulator-always-on
- wd2: remove pm-ignore-notify, it is not implemented and documented
- wd2: remove duplicate non-removable
changes v8:
- resend
changes v7:
- VT7: reorder node alphabetically
- VT7: rename "reg_12v_bl: regulator-bl-12v" to "reg_bl_12v0: regulator-bl-12v0"
- VT7: remove panel and TS nodes. This drivers are currently not
mainline.
- prti6q.dtsi: move reg_1v8 to prti6q.dts
- prti6q.dtsi: remove pinctrl from the can1 node. It is done on almost
every board file.
changes v6:
- move fsl.yaml changes to separate patch
- remove partitions, they are provided by the bootloader
- update flash compatible
- rename can3 to can
- fix fsl,mode
- fix interrupt in the wlan node on PRTI6Q
changes v5:
- PRTI6Q: remove status from the pwm-backlight node
- drop the vendor-prefixes patch, it is already taken by Rob
- add Reviewed-by: Rob Herring <[email protected]>
changes v4:
- VT7: fix typo
changes v3:
- move compatible to the start of node
- move status to the end
- use generic names in compatible
- refactor dts/dtsi
- use alphabet order for pinctrl and phandels
- remove unused or currently not supported nodes
changes v2:
- squash PRTI6Q patches
Oleksij Rempel (5):
dt-bindings: arm: fsl: add different Protonic boards
ARM: dts: add Protonic PRTI6Q board
ARM: dts: add Protonic WD2 board
ARM: dts: add Protonic VT7 board
ARM: dts: add Protonic RVT board
.../devicetree/bindings/arm/fsl.yaml | 4 +
arch/arm/boot/dts/Makefile | 4 +
arch/arm/boot/dts/imx6dl-prtrvt.dts | 184 ++++++
arch/arm/boot/dts/imx6dl-prtvt7.dts | 410 +++++++++++++
arch/arm/boot/dts/imx6q-prti6q.dts | 542 ++++++++++++++++++
arch/arm/boot/dts/imx6q-prtwd2.dts | 188 ++++++
arch/arm/boot/dts/imx6qdl-prti6q.dtsi | 163 ++++++
7 files changed, 1496 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-prtrvt.dts
create mode 100644 arch/arm/boot/dts/imx6dl-prtvt7.dts
create mode 100644 arch/arm/boot/dts/imx6q-prti6q.dts
create mode 100644 arch/arm/boot/dts/imx6q-prtwd2.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-prti6q.dtsi
--
2.27.0
Protonic PRTI6Q is a development board and a base class for different
specific customer application boards based on the i.MX6 family of SoCs,
developed by Protonic Holland.
Reviewed-by: Rob Herring <[email protected]>
Signed-off-by: David Jander <[email protected]>
Signed-off-by: Oleksij Rempel <[email protected]>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/imx6q-prti6q.dts | 542 ++++++++++++++++++++++++++
arch/arm/boot/dts/imx6qdl-prti6q.dtsi | 163 ++++++++
3 files changed, 706 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6q-prti6q.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-prti6q.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e6a1cac0bfc7..38ad7455ca30 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -543,6 +543,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
imx6q-pico-nymph.dtb \
imx6q-pico-pi.dtb \
imx6q-pistachio.dtb \
+ imx6q-prti6q.dtb \
imx6q-rex-pro.dtb \
imx6q-sabreauto.dtb \
imx6q-sabrelite.dtb \
diff --git a/arch/arm/boot/dts/imx6q-prti6q.dts b/arch/arm/boot/dts/imx6q-prti6q.dts
new file mode 100644
index 000000000000..190abf0b1ccc
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-prti6q.dts
@@ -0,0 +1,542 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+/dts-v1/;
+#include "imx6q.dtsi"
+#include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+ model = "Protonic PRTI6Q board";
+ compatible = "prt,prti6q", "fsl,imx6q";
+
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0xf0000000>;
+ };
+
+ backlight_lcd: backlight-lcd {
+ compatible = "pwm-backlight";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_backlight>;
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 16 64 255>;
+ num-interpolated-steps = <16>;
+ default-brightness-level = <1>;
+ power-supply = <®_3v3>;
+ enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ can_osc: can-osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <25000000>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_leds>;
+
+ led-debug0 {
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-debug1 {
+ function = LED_FUNCTION_SD;
+ gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "disk-activity";
+ };
+ };
+
+ panel {
+ compatible = "kyo,tcg121xglp";
+ backlight = <&backlight_lcd>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+
+ reg_1v8: regulator-1v8 {
+ compatible = "regulator-fixed";
+ regulator-name = "1v8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ reg_wifi: regulator-wifi {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi_npd>;
+ enable-active-high;
+ gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+ regulator-max-microvolt = <1800000>;
+ regulator-min-microvolt = <1800000>;
+ regulator-name = "regulator-WL12xx";
+ startup-delay-us = <70000>;
+ };
+
+ sound {
+ compatible = "simple-audio-card";
+ simple-audio-card,name = "prti6q-sgtl5000";
+ simple-audio-card,format = "i2s";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Line", "Line In Jack",
+ "Headphone", "Headphone Jack",
+ "Speaker", "External Speaker";
+ simple-audio-card,routing =
+ "MIC_IN", "Microphone Jack",
+ "LINE_IN", "Line In Jack",
+ "Headphone Jack", "HP_OUT",
+ "External Speaker", "LINE_OUT";
+
+ simple-audio-card,cpu {
+ sound-dai = <&ssi1>;
+ system-clock-frequency = <0>;
+ };
+
+ simple-audio-card,codec {
+ sound-dai = <&sgtl5000>;
+ bitclock-master;
+ frame-master;
+ };
+ };
+
+ sound-spdif {
+ compatible = "fsl,imx-audio-spdif";
+ model = "imx-spdif";
+ spdif-controller = <&spdif>;
+ spdif-in;
+ spdif-out;
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+
+ mux-ssi1 {
+ fsl,audmux-port = <0>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN 0
+ IMX_AUDMUX_V2_PTCR_TFSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TCSEL(2) 0
+ IMX_AUDMUX_V2_PTCR_TFSDIR 0
+ IMX_AUDMUX_V2_PTCR_TCLKDIR IMX_AUDMUX_V2_PDCR_RXDSEL(2)
+ >;
+ };
+
+ mux-pins3 {
+ fsl,audmux-port = <2>;
+ fsl,port-config = <
+ IMX_AUDMUX_V2_PTCR_SYN IMX_AUDMUX_V2_PDCR_RXDSEL(0)
+ 0 IMX_AUDMUX_V2_PDCR_TXRXEN
+ >;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can2>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>, <&gpio4 25 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>;
+ status = "okay";
+
+ can@0 {
+ compatible = "microchip,mcp2515";
+ reg = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can3>;
+ clocks = <&can_osc>;
+ interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+ spi-max-frequency = <5000000>;
+ };
+
+ adc@1 {
+ compatible = "ti,adc128s052";
+ reg = <1>;
+ spi-max-frequency = <2000000>;
+ vref-supply = <®_3v3>;
+ };
+};
+
+&ecspi3 {
+ cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi3>;
+ status = "okay";
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&rgmii_phy>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Microchip KSZ9031RNX PHY */
+ rgmii_phy: ethernet-phy@4 {
+ reg = <4>;
+ interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ };
+ };
+};
+
+&hdmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hdmi>;
+ ddc-i2c-bus = <&i2c2>;
+ status = "okay";
+};
+
+&i2c1 {
+ sgtl5000: audio-codec@a {
+ compatible = "fsl,sgtl5000";
+ reg = <0xa>;
+ #sound-dai-cells = <0>;
+ clocks = <&clks 201>;
+ VDDA-supply = <®_3v3>;
+ VDDIO-supply = <®_3v3>;
+ VDDD-supply = <®_1v8>;
+ };
+};
+
+/* DDC */
+&i2c2 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ adc@49 {
+ compatible = "ti,ads1015";
+ reg = <0x49>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* can2_l */
+ channel@4 {
+ reg = <4>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can2_h */
+ channel@5 {
+ reg = <5>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_l */
+ channel@6 {
+ reg = <6>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+
+ /* can1_h */
+ channel@7 {
+ reg = <7>;
+ ti,gain = <3>;
+ ti,datarate = <3>;
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ status = "okay";
+
+ port@4 {
+ reg = <4>;
+
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&sata {
+ status = "okay";
+};
+
+&snvs_poweroff {
+ status = "okay";
+};
+
+&spdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spdif>;
+ status = "okay";
+};
+
+&ssi1 {
+ #sound-dai-cells = <0>;
+ fsl,mode = "ac97-slave";
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart5>;
+ status = "okay";
+};
+
+&usbotg {
+ pinctrl-0 = <&pinctrl_usbotg &pinctrl_usbotg_id>;
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ non-removable;
+ vmmc-supply = <®_wifi>;
+ cap-power-off-card;
+ keep-power-in-suspend;
+ status = "okay";
+
+ wifi {
+ compatible = "ti,wl1271";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wifi>;
+ interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
+ ref-clock-frequency = "38400000";
+ tcxo-clock-frequency = "19200000";
+ };
+};
+
+&iomuxc {
+ pinctrl_audmux: audmuxgrp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0x030b0
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0
+ >;
+ };
+
+ pinctrl_backlight: backlightgrp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28 0x1b0b0
+ >;
+ };
+
+ pinctrl_can2: can2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b008
+ MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b008
+ >;
+ };
+
+ pinctrl_can3: can3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x1b0b1
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ /* CS */
+ MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
+ >;
+ };
+
+ pinctrl_ecspi2_cs: ecspi2csgrp {
+ fsl,pins = <
+ /* ADC128S022 CS */
+ MX6QDL_PAD_DISP0_DAT4__GPIO4_IO25 0x1b0b1
+ >;
+ };
+
+ pinctrl_ecspi3: ecspi3grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1
+ MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1
+ MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1
+ MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x000b1
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b030
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b030
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b030
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b030
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b030
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b030
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x10030
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x10030
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x10030
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x10030
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x10030
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x10030
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x10030
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x10030
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x10030
+
+ /* Phy reset */
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0
+ MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x1b0b1
+ >;
+ };
+
+ pinctrl_hdmi: hdmigrp {
+ fsl,pins = <
+ /* NOTE: DDC is done via I2C2, so DON'T
+ * configure DDC pins for HDMI!
+ */
+ MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0
+ >;
+ };
+
+ /* DDC */
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_leds: ledsgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x1b0b0
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_spdif: spdifgrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
+ MX6QDL_PAD_GPIO_19__SPDIF_OUT 0x1b0b0
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart5: uart5grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg_id: usbotgidgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1f058
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x170b9
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x100b9
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x170b9
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x170b9
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x170b9
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_wifi: wifigrp {
+ fsl,pins = <
+ /* WL12xx IRQ */
+ MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x10880
+ >;
+ };
+
+ pinctrl_wifi_npd: wifinpd {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x1b8b0
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
new file mode 100644
index 000000000000..19578f660b09
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2014 Protonic Holland
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_usb_h1_vbus: regulator-h1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "h1-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_usb_otg_vbus: regulator-otg-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "otg-vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&can1 {
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c3 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ temperature-sensor@70 {
+ compatible = "ti,tmp103";
+ reg = <0x70>;
+ };
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usb_h1_vbus>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usb_otg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ phy_type = "utmi";
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&usdhc3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc3>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_can1: can1grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x1b008
+ MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x1b008
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001f8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001f8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x100f9
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f9
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f9
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f9
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f9
+ MX6QDL_PAD_GPIO_1__GPIO1_IO01 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc3: usdhc3grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17099
+ MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10099
+ MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17099
+ MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17099
+ MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17099
+ MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17099
+ MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17099
+ MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17099
+ MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17099
+ MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17099
+ MX6QDL_PAD_SD3_RST__SD3_RESET 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b0b0
+ MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0
+ >;
+ };
+};
--
2.27.0
On Wed, Jul 01, 2020 at 03:03:25PM +0200, Oleksij Rempel wrote:
> Oleksij Rempel (5):
> dt-bindings: arm: fsl: add different Protonic boards
> ARM: dts: add Protonic PRTI6Q board
> ARM: dts: add Protonic WD2 board
> ARM: dts: add Protonic VT7 board
> ARM: dts: add Protonic RVT board
Applied all, thanks.