Hi folks,
Does anybody know what this message in kern.log means?
eth0: command 0x3002 did not complete! Status=0xffff
It comes up when I try to setup a pppoe connection to my provider.
The interface is a 3c59x.
Any help would be highly appreciated
Harri
Harald Dunkel wrote:
>
> Hi folks,
>
> Does anybody know what this message in kern.log means?
>
> eth0: command 0x3002 did not complete! Status=0xffff
>
There's a function in the driver which issues reset commands to the
hardware and then spins, waiting for completion. Usually it takes
a single PCI cycle. In your case it timed out.
It look to me like the NIC is powered down. Could you please
send me a bunch of info:
- Does the interface actually work after this message, or is
it dead?
- If the latter, did you warmboot from another OS?
- Does it help if you add the line
options 3c59x enable_wol=1
to /etc/modules.conf? (This is a misnomer - enable_wol
enables the driver's power management functions).
Thanks.
Hi Andrew,
Andrew Morton wrote:
>
> Harald Dunkel wrote:
> >
> > Hi folks,
> >
> > Does anybody know what this message in kern.log means?
> >
> > eth0: command 0x3002 did not complete! Status=0xffff
> >
>
> There's a function in the driver which issues reset commands to the
> hardware and then spins, waiting for completion. Usually it takes
> a single PCI cycle. In your case it timed out.
>
> It look to me like the NIC is powered down. Could you please
> send me a bunch of info:
>
> - Does the interface actually work after this message, or is
> it dead?
>
A ping to the assigned IP address works. But I cannot get a PPPoE
connection.
> - If the latter, did you warmboot from another OS?
>
I've got just Linux. The problem occurs after a warm boot as
it seems. When I do a power-down reset, then I don't get this
message, but I don't get a connection via PPPoE, either.
> - Does it help if you add the line
>
> options 3c59x enable_wol=1
>
> to /etc/modules.conf? (This is a misnomer - enable_wol
> enables the driver's power management functions).
>
No, this did not help. I found an old EMail with the suggestion
to add enable_wol=0, but this didn't help, either.
The problem came up this morning (12 hours ago). Before the it was
working, AFAICT.
Regards
Harri
PS: The message about '0x3002 did not complete' is gone. I haven't seen
it anymore since I added the 'options 3c59x enable_wol=1'.
But now I get this in my syslog:
Oct 29 20:41:19 bilbo pppd[522]: pppd 2.4.1 started by root, uid 0
Oct 29 20:41:20 bilbo pppd[522]: Sending PADI
Oct 29 20:41:20 bilbo kernel: eth0: Transmit error, Tx status register 90.
Oct 29 20:41:20 bilbo kernel: Flags; bus-master 1, dirty 0(0) current 1(1)
Oct 29 20:41:20 bilbo kernel: Transmit list 00000000 vs. df230200.
Oct 29 20:41:20 bilbo kernel: 0: @df230200 length 80000020 status 80000020
Oct 29 20:41:20 bilbo kernel: 1: @df230240 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 2: @df230280 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 3: @df2302c0 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 4: @df230300 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 5: @df230340 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 6: @df230380 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 7: @df2303c0 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 8: @df230400 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 9: @df230440 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 10: @df230480 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 11: @df2304c0 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 12: @df230500 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 13: @df230540 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 14: @df230580 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: 15: @df2305c0 length 00000000 status 00000000
Oct 29 20:41:20 bilbo kernel: scsi0: PCI error Interrupt at seqaddr = 0x9
Oct 29 20:41:20 bilbo kernel: scsi0: Data Parity Error Detected during address or write data phase
Oct 29 20:41:20 bilbo kernel: scsi1: PCI error Interrupt at seqaddr = 0x9
Oct 29 20:41:20 bilbo kernel: scsi1: Data Parity Error Detected during address or write data phase
Especially interesting is the message about the SCSI. How is this
related to the 3c59x?
Regards
Harri
Harald Dunkel wrote:
>
> PS: The message about '0x3002 did not complete' is gone. I haven't seen
> it anymore since I added the 'options 3c59x enable_wol=1'.
>
> But now I get this in my syslog:
>
> Oct 29 20:41:19 bilbo pppd[522]: pppd 2.4.1 started by root, uid 0
> Oct 29 20:41:20 bilbo pppd[522]: Sending PADI
> Oct 29 20:41:20 bilbo kernel: eth0: Transmit error, Tx status register 90.
0x90 -> Transmit underrun. The NIC wasn't able to get data
from main memory fast enough. Across PCI.
> ...
> Oct 29 20:41:20 bilbo kernel: scsi0: PCI error Interrupt at seqaddr = 0x9
I wonder what that error is?
>
> Especially interesting is the message about the SCSI. How is this
> related to the 3c59x?
The PCI bus is screwed up. I haven't seen this before.
Is the machine otherwise stable? What's special about bringing
up PPPoE? Have you tested the machine well against other hosts
on the LAN?
Andrew Morton wrote:
>
> The PCI bus is screwed up. I haven't seen this before.
> Is the machine otherwise stable? What's special about bringing
> up PPPoE? Have you tested the machine well against other hosts
> on the LAN?
The eth0 has the address 192.168.1.1 . When I do a ping 192.168.1.2,
then I get an error message, too:
Oct 29 21:28:49 bilbo kernel: scsi0: PCI error Interrupt at seqaddr = 0x8
Oct 29 21:28:49 bilbo kernel: scsi0: Data Parity Error Detected during address or write data phase
Oct 29 21:28:49 bilbo kernel: eth0: Transmit error, Tx status register ff.
Oct 29 21:28:49 bilbo kernel: Flags; bus-master 1, dirty 1(1) current 1(1)
Oct 29 21:28:49 bilbo kernel: Transmit list ffffffff vs. df231240.
Oct 29 21:28:49 bilbo kernel: 0: @df231200 length 8000002a status 8000002a
Oct 29 21:28:49 bilbo kernel: 1: @df231240 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 2: @df231280 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 3: @df2312c0 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 4: @df231300 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 5: @df231340 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 6: @df231380 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 7: @df2313c0 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 8: @df231400 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 9: @df231440 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 10: @df231480 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 11: @df2314c0 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 12: @df231500 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 13: @df231540 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 14: @df231580 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: 15: @df2315c0 length 00000000 status 00000000
Oct 29 21:28:49 bilbo kernel: eth0: Updating statistics failed, disabling stats as an interrupt source.
Oct 29 21:28:49 bilbo kernel: eth0: Host error, FIFO diagnostic register ffff.
Oct 29 21:28:49 bilbo kernel: eth0: PCI bus error, bus status ffffffff
Oct 29 21:28:49 bilbo kernel: scsi1: PCI error Interrupt at seqaddr = 0x8
Oct 29 21:28:49 bilbo kernel: scsi1: Data Parity Error Detected during address or write data phase
PPPoE was not involved in this. It wasn't even started.
Maybe the NIC is broken?
Regards
Harri
Is the NIC sharing interrupts or I/O ports with
the SCSI HBAs?
On 10/29/2001 21:34 +0100, Harald Dunkel wrote:
>> Andrew Morton wrote:
>> >
>> > The PCI bus is screwed up. I haven't seen this before.
>> > Is the machine otherwise stable? What's special about bringing
>> > up PPPoE? Have you tested the machine well against other hosts
>> > on the LAN?
>>
>> The eth0 has the address 192.168.1.1 . When I do a ping 192.168.1.2,
>> then I get an error message, too:
>>
>> Oct 29 21:28:49 bilbo kernel: scsi0: PCI error Interrupt at seqaddr = 0x8
>> Oct 29 21:28:49 bilbo kernel: scsi0: Data Parity Error Detected during address or write data phase
>> Oct 29 21:28:49 bilbo kernel: eth0: Transmit error, Tx status register ff.
>> Oct 29 21:28:49 bilbo kernel: Flags; bus-master 1, dirty 1(1) current 1(1)
>> Oct 29 21:28:49 bilbo kernel: Transmit list ffffffff vs. df231240.
>> Oct 29 21:28:49 bilbo kernel: 0: @df231200 length 8000002a status 8000002a
>> Oct 29 21:28:49 bilbo kernel: 1: @df231240 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 2: @df231280 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 3: @df2312c0 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 4: @df231300 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 5: @df231340 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 6: @df231380 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 7: @df2313c0 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 8: @df231400 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 9: @df231440 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 10: @df231480 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 11: @df2314c0 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 12: @df231500 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 13: @df231540 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 14: @df231580 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: 15: @df2315c0 length 00000000 status 00000000
>> Oct 29 21:28:49 bilbo kernel: eth0: Updating statistics failed, disabling stats as an interrupt source.
>> Oct 29 21:28:49 bilbo kernel: eth0: Host error, FIFO diagnostic register ffff.
>> Oct 29 21:28:49 bilbo kernel: eth0: PCI bus error, bus status ffffffff
>> Oct 29 21:28:49 bilbo kernel: scsi1: PCI error Interrupt at seqaddr = 0x8
>> Oct 29 21:28:49 bilbo kernel: scsi1: Data Parity Error Detected during address or write data phase
>>
>>
>> PPPoE was not involved in this. It wasn't even started.
>>
>> Maybe the NIC is broken?
>>
>>
>> Regards
>>
>> Harri
>> -
>> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>> the body of a message to [email protected]
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>> Please read the FAQ at http://www.tux.org/lkml/
End of included message
--
[email protected]
Tim Walberg wrote:
>
> Is the NIC sharing interrupts or I/O ports with
> the SCSI HBAs?
>
Nope:
Bus 0, device 10, function 0:
SCSI storage controller: Adaptec 7899A (rev 1).
IRQ 15.
Master Capable. Latency=32. Min Gnt=40.Max Lat=25.
I/O at 0xa000 [0xa0ff].
Non-prefetchable 64 bit memory at 0xd5000000 [0xd5000fff].
Bus 0, device 10, function 1:
SCSI storage controller: Adaptec 7899A (#2) (rev 1).
IRQ 9.
Master Capable. Latency=32. Min Gnt=40.Max Lat=25.
I/O at 0x9800 [0x98ff].
Non-prefetchable 64 bit memory at 0xd4800000 [0xd4800fff].
Bus 0, device 11, function 0:
Ethernet controller: 3Com Corporation 3c900 Combo [Boomerang] (rev 0).
IRQ 10.
Master Capable. Latency=32. Min Gnt=3.Max Lat=8.
I/O at 0x9400 [0x943f].
The SCSI controller is an Adaptec 39160, so it allocates 2 IRQs, 2 I/Os,
etc.
Regards
Harri
On Monday 29 October 2001 20:58, Andrew Morton wrote:
> > scsi0: PCI error Interrupt at seqaddr = 0x9
> > scsi0: Data Parity Error Detected during address or write data phase>
> The PCI bus is screwed up. I haven't seen this before.
> Is the machine otherwise stable? What's special about bringing
> up PPPoE? Have you tested the machine well against other hosts
> on the LAN?
I have exactly the same error message when trying to use my Davicom card,
actually an endless number of them. I just don't use that card anymore.
Last kernel I tried was 2.4.8-ac10
Both drivers dmfe and tulip give same error. Network traffic on this
card is extremely slow, otherwise the machine is as solid as a rock
since 2 years. MB Asus P2B-S, PII 300
I already tried enabling X86_UP_IOAPIC (was disabled before),
but that didn't change anything.
Davicom DM9xxx net driver, version 1.36p1 (May 12, 2001)
PCI: Found IRQ 9 for device 00:09.0
PCI: Sharing IRQ 9 with 00:04.2
PCI: Sharing IRQ 9 with 00:06.0
PCI: Setting latency timer of device 00:09.0 to 64
eth0: Davicom DM9102 at 0xb800, 00:80:ad:03:34:0a, IRQ 9
scsi0: PCI error Interrupt at seqaddr = 0x8
scsi0: Data Parity Error Detected during address or write data phase
scsi0: PCI error Interrupt at seqaddr = 0x8
scsi0: Data Parity Error Detected during address or write data phase
scsi0: PCI error Interrupt at seqaddr = 0x8
scsi0: Data Parity Error Detected during address or write data phase
scsi0: PCI error Interrupt at seqaddr = 0x8
scsi0: Data Parity Error Detected during address or write data phase
scsi0: PCI error Interrupt at seqaddr = 0x8
scsi0: Data Parity Error Detected during address or write data phase
ne.c:v1.10 9/23/94 Donald Becker ([email protected])
Last modified Nov 1, 2000 by Paul Gortmaker
NE*000 ethercard probe at 0x300: 00 00 e8 a4 1f 36
eth1: NE2000 found at 0x300, using IRQ 5.
cat /proc/interrupts
? ? ? ? ? ?CPU0
? 0: ? ? 134033 ? ? ? ? ?XT-PIC ?timer
? 1: ? ? ? 2971 ? ? ? ? ?XT-PIC ?keyboard
? 2: ? ? ? ? ?0 ? ? ? ? ?XT-PIC ?cascade
? 5: ? ? ? ? 50 ? ? ? ? ?XT-PIC ?NE2000
? 8: ? ? ? ? 21 ? ? ? ? ?XT-PIC ?rtc
? 9: ? ? 141554 ? ? ? ? ?XT-PIC ?aic7xxx, usb-uhci, HiSax, eth0, es1371
?12: ? ? ?28437 ? ? ? ? ?XT-PIC ?PS/2 Mouse
?14: ? ? ?19072 ? ? ? ? ?XT-PIC ?ide0
?15: ? ? ? ?213 ? ? ? ? ?XT-PIC ?ide1
NMI: ? ? ? ? ?0
LOC: ? ? 133993
ERR: ? ? ? ? ?0
MIS: ? ? ? ? ?0
cat /proc/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 04 Lun: 00
? Vendor: TEAC ? ? Model: CD-R58S ? ? ? ? ?Rev: 1.0P
? Type: ? CD-ROM ? ? ? ? ? ? ? ? ? ? ? ? ? ANSI SCSI revision: 02
cat /proc/scsi/aic7xxx/0
Adaptec AIC7xxx driver version: 6.2.1
aic7890/91: Ultra2 Wide Channel A, SCSI Id=7, 32/255 SCBs
Channel A Target 0 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 1 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 2 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 3 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 4 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
? ? ? ? Goal: 40.000MB/s transfers (40.000MHz, offset 127)
? ? ? ? Curr: 3.300MB/s transfers
? ? ? ? Channel A Target 4 Lun 0 Settings
? ? ? ? ? ? ? ? Commands Queued 1
? ? ? ? ? ? ? ? Commands Active 0
? ? ? ? ? ? ? ? Command Openings 1
? ? ? ? ? ? ? ? Max Tagged Openings 0
? ? ? ? ? ? ? ? Device Queue Frozen Count 0
Channel A Target 5 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 6 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 7 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 8 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 9 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 10 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 11 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 12 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 13 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 14 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
Channel A Target 15 Negotiation Settings
? ? ? ? User: 80.000MB/s transfers (40.000MHz, offset 255, 16bit)
/usr/src/linux$ lspci -vv
00:00.0 Host bridge: Intel Corporation 440BX/ZX - 82443BX/ZX Host bridge (rev 02)
? ? ? ? Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
? ? ? ? Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR+
? ? ? ? Latency: 64
? ? ? ? Region 0: Memory at e4000000 (32-bit, prefetchable) [size=64M]
? ? ? ? Capabilities: <available only to root>
00:01.0 PCI bridge: Intel Corporation 440BX/ZX - 82443BX/ZX AGP bridge (rev 02) (prog-if 00 [Normal decode])
? ? ? ? Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
? ? ? ? Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
? ? ? ? Latency: 64
? ? ? ? Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
? ? ? ? Memory behind bridge: d6000000-d7dfffff
? ? ? ? Prefetchable memory behind bridge: d7f00000-e3ffffff
? ? ? ? BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
?
00:04.0 ISA bridge: Intel Corporation 82371AB PIIX4 ISA (rev 02)
? ? ? ? Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
? ? ? ? Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
? ? ? ? Latency: 0
?
00:04.1 IDE interface: Intel Corporation 82371AB PIIX4 IDE (rev 01) (prog-if 80 [Master])
? ? ? ? Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
? ? ? ? Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
? ? ? ? Latency: 0
? ? ? ? Region 4: I/O ports at d800 [size=16]
?
00:04.2 USB Controller: Intel Corporation 82371AB PIIX4 USB (rev 01) (prog-if 00 [UHCI])
? ? ? ? Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
? ? ? ? Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
? ? ? ? Latency: 64
? ? ? ? Interrupt: pin D routed to IRQ 9
? ? ? ? Region 4: I/O ports at d400 [size=32]
?
00:04.3 Bridge: Intel Corporation 82371AB PIIX4 ACPI (rev 02)
? ? ? ? Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
? ? ? ? Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
? ? ? ? Interrupt: pin ? routed to IRQ 9
?
00:06.0 SCSI storage controller: Adaptec AHA-2940U2/W / 7890
? ? ? ? Subsystem: Adaptec 2940U2W SCSI Controller
? ? ? ? Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
? ? ? ? Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
? ? ? ? Latency: 64 (9750ns min, 6250ns max), cache line size 08
? ? ? ? Interrupt: pin A routed to IRQ 9
? ? ? ? BIST result: 00
? ? ? ? Region 0: I/O ports at d000 [disabled] [size=256]
? ? ? ? Region 1: Memory at d5800000 (64-bit, non-prefetchable) [size=4K]
? ? ? ? Expansion ROM at <unassigned> [disabled] [size=128K]
? ? ? ? Capabilities: <available only to root>
?
00:09.0 Ethernet controller: Davicom Semiconductor, Inc. Ethernet 100/10 MBit (rev 31)
? ? ? ? Subsystem: Unknown device 3030:5032
? ? ? ? Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
? ? ? ? Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR+
? ? ? ? Latency: 64 (5000ns min, 10000ns max)
? ? ? ? Interrupt: pin A routed to IRQ 9
? ? ? ? Region 0: I/O ports at b800 [size=256]
? ? ? ? Region 1: Memory at d5000000 (32-bit, non-prefetchable) [size=256]
? ? ? ? Expansion ROM at <unassigned> [disabled] [size=256K]
? ? ? ? Capabilities: <available only to root>
?
00:0a.0 Network controller: AVM Audiovisuelles MKTG & Computer System GmbH A1 ISDN [Fritz] (rev 02)
? ? ? ? Subsystem: AVM Audiovisuelles MKTG & Computer System GmbH FRITZ!Card ISDN Controller
? ? ? ? Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
? ? ? ? Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
? ? ? ? Interrupt: pin A routed to IRQ 9
? ? ? ? Region 0: Memory at d4800000 (32-bit, non-prefetchable) [size=32]
? ? ? ? Region 1: I/O ports at b400 [size=32]
?
00:0b.0 Multimedia audio controller: Ensoniq ES1371 [AudioPCI-97] (rev 06)
? ? ? ? Subsystem: Ensoniq Creative Sound Blaster AudioPCI64V, AudioPCI128
? ? ? ? Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
? ? ? ? Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort+ <MAbort+ >SERR- <PERR-
? ? ? ? Latency: 64 (3000ns min, 32000ns max)
? ? ? ? Interrupt: pin A routed to IRQ 9
? ? ? ? Region 0: I/O ports at b000 [size=64]
? ? ? ? Capabilities: <available only to root>
?
01:00.0 VGA compatible controller: nVidia Corporation NV11 (rev b2) (prog-if 00 [VGA])
? ? ? ? Subsystem: Micro-star International Co Ltd: Unknown device 8826
? ? ? ? Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
? ? ? ? Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
? ? ? ? Latency: 64 (1250ns min, 250ns max)
? ? ? ? Interrupt: pin A routed to IRQ 11
? ? ? ? Region 0: Memory at d6000000 (32-bit, non-prefetchable) [size=16M]
? ? ? ? Region 1: Memory at d8000000 (32-bit, prefetchable) [size=128M]
? ? ? ? Expansion ROM at d7ff0000 [disabled] [size=64K]
? ? ? ? Capabilities: <available only to root>
#
# Automatically generated by make menuconfig: don't edit
#
CONFIG_X86=y
CONFIG_ISA=y
# CONFIG_SBUS is not set
CONFIG_UID16=y
#
# Code maturity level options
#
CONFIG_EXPERIMENTAL=y
#
# Loadable module support
#
CONFIG_MODULES=y
CONFIG_MODVERSIONS=y
CONFIG_KMOD=y
#
# Processor type and features
#
# CONFIG_M386 is not set
# CONFIG_M486 is not set
CONFIG_M586=y
# CONFIG_M586TSC is not set
# CONFIG_M586MMX is not set
# CONFIG_M686 is not set
# CONFIG_MPENTIUMIII is not set
# CONFIG_MPENTIUM4 is not set
# CONFIG_MK6 is not set
# CONFIG_MK7 is not set
# CONFIG_MCRUSOE is not set
# CONFIG_MWINCHIPC6 is not set
# CONFIG_MWINCHIP2 is not set
# CONFIG_MWINCHIP3D is not set
# CONFIG_MCYRIXIII is not set
CONFIG_X86_WP_WORKS_OK=y
CONFIG_X86_INVLPG=y
CONFIG_X86_CMPXCHG=y
CONFIG_X86_XADD=y
CONFIG_X86_BSWAP=y
CONFIG_X86_POPAD_OK=y
# CONFIG_RWSEM_GENERIC_SPINLOCK is not set
CONFIG_RWSEM_XCHGADD_ALGORITHM=y
CONFIG_X86_L1_CACHE_SHIFT=5
CONFIG_X86_USE_STRING_486=y
CONFIG_X86_ALIGNMENT_16=y
CONFIG_TOSHIBA=m
CONFIG_MICROCODE=m
CONFIG_X86_MSR=m
CONFIG_X86_CPUID=m
CONFIG_NOHIGHMEM=y
# CONFIG_HIGHMEM4G is not set
# CONFIG_HIGHMEM64G is not set
# CONFIG_MATH_EMULATION is not set
CONFIG_MTRR=y
# CONFIG_SMP is not set
CONFIG_X86_UP_APIC=y
CONFIG_X86_UP_IOAPIC=y
CONFIG_X86_LOCAL_APIC=y
CONFIG_X86_IO_APIC=y
#
# General setup
#
CONFIG_NET=y
# CONFIG_VISWS is not set
CONFIG_PCI=y
# CONFIG_PCI_GOBIOS is not set
# CONFIG_PCI_GODIRECT is not set
CONFIG_PCI_GOANY=y
CONFIG_PCI_BIOS=y
CONFIG_PCI_DIRECT=y
CONFIG_PCI_NAMES=y
CONFIG_EISA=y
# CONFIG_MCA is not set
CONFIG_HOTPLUG=y
#
# PCMCIA/CardBus support
#
# CONFIG_PCMCIA is not set
CONFIG_SYSVIPC=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_SYSCTL=y
CONFIG_KCORE_ELF=y
# CONFIG_KCORE_AOUT is not set
CONFIG_BINFMT_AOUT=m
CONFIG_BINFMT_ELF=y
CONFIG_BINFMT_MISC=m
CONFIG_PM=y
# CONFIG_ACPI is not set
CONFIG_APM=y
# CONFIG_APM_IGNORE_USER_SUSPEND is not set
CONFIG_APM_DO_ENABLE=y
CONFIG_APM_CPU_IDLE=y
# CONFIG_APM_DISPLAY_BLANK is not set
CONFIG_APM_RTC_IS_GMT=y
# CONFIG_APM_ALLOW_INTS is not set
# CONFIG_APM_REAL_MODE_POWER_OFF is not set
#
# Binary emulation of other systems
#
CONFIG_ABI=m
CONFIG_ABI_SVR4=m
# CONFIG_ABI_UW7 is not set
# CONFIG_ABI_SOLARIS is not set
CONFIG_ABI_IBCS=m
# CONFIG_ABI_ISC is not set
# CONFIG_ABI_XENIX is not set
CONFIG_ABI_SCO=m
CONFIG_ABI_WYSE=m
CONFIG_ABI_CXENIX=m
CONFIG_BINFMT_COFF=m
CONFIG_BINFMT_XOUT=m
# CONFIG_BINFMT_XOUT_X286 is not set
CONFIG_ABI_VERBOSE_ERRORS=y
CONFIG_ABI_SPX=y
CONFIG_ABI_XTI=y
CONFIG_ABI_TLI_OPTMGMT=y
# CONFIG_ABI_XTI_OPTMGMT is not set
#
# Memory Technology Devices (MTD)
#
# CONFIG_MTD is not set
#
# Parallel port support
#
CONFIG_PARPORT=m
CONFIG_PARPORT_PC=m
CONFIG_PARPORT_PC_CML1=m
# CONFIG_PARPORT_SERIAL is not set
CONFIG_PARPORT_PC_FIFO=y
CONFIG_PARPORT_PC_SUPERIO=y
# CONFIG_PARPORT_AMIGA is not set
# CONFIG_PARPORT_MFC3 is not set
# CONFIG_PARPORT_ATARI is not set
# CONFIG_PARPORT_GSC is not set
# CONFIG_PARPORT_SUNBPP is not set
CONFIG_PARPORT_OTHER=y
CONFIG_PARPORT_1284=y
#
# Plug and Play configuration
#
CONFIG_PNP=y
CONFIG_ISAPNP=y
# CONFIG_PNPBIOS is not set
#
# Block devices
#
CONFIG_BLK_DEV_FD=m
# CONFIG_BLK_DEV_XD is not set
# CONFIG_PARIDE is not set
# CONFIG_BLK_CPQ_DA is not set
# CONFIG_BLK_CPQ_CISS_DA is not set
# CONFIG_BLK_DEV_DAC960 is not set
CONFIG_BLK_DEV_LOOP=m
CONFIG_BLK_DEV_NBD=m
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=4096
CONFIG_BLK_DEV_INITRD=y
#
# Multi-device support (RAID and LVM)
#
# CONFIG_MD is not set
# CONFIG_BLK_DEV_MD is not set
# CONFIG_MD_LINEAR is not set
# CONFIG_MD_RAID0 is not set
# CONFIG_MD_RAID1 is not set
# CONFIG_MD_RAID5 is not set
# CONFIG_BLK_DEV_LVM is not set
#
# Networking options
#
CONFIG_PACKET=m
CONFIG_PACKET_MMAP=y
CONFIG_NETLINK=y
CONFIG_RTNETLINK=y
CONFIG_NETLINK_DEV=m
CONFIG_NETFILTER=y
# CONFIG_NETFILTER_DEBUG is not set
CONFIG_FILTER=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_ADVANCED_ROUTER=y
CONFIG_RTNETLINK=y
CONFIG_NETLINK=y
# CONFIG_IP_MULTIPLE_TABLES is not set
# CONFIG_IP_ROUTE_MULTIPATH is not set
# CONFIG_IP_ROUTE_TOS is not set
# CONFIG_IP_ROUTE_VERBOSE is not set
# CONFIG_IP_ROUTE_LARGE_TABLES is not set
# CONFIG_IP_PNP is not set
CONFIG_NET_IPIP=m
CONFIG_NET_IPGRE=m
CONFIG_NET_IPGRE_BROADCAST=y
CONFIG_IP_MROUTE=y
CONFIG_IP_PIMSM_V1=y
CONFIG_IP_PIMSM_V2=y
# CONFIG_ARPD is not set
# CONFIG_INET_ECN is not set
# CONFIG_SYN_COOKIES is not set
#
# ? IP: Netfilter Configuration
#
CONFIG_IP_NF_CONNTRACK=m
CONFIG_IP_NF_FTP=m
CONFIG_IP_NF_QUEUE=m
CONFIG_IP_NF_IPTABLES=m
CONFIG_IP_NF_MATCH_LIMIT=m
CONFIG_IP_NF_MATCH_MAC=m
CONFIG_IP_NF_MATCH_MARK=m
CONFIG_IP_NF_MATCH_MULTIPORT=m
CONFIG_IP_NF_MATCH_TOS=m
CONFIG_IP_NF_MATCH_TCPMSS=m
CONFIG_IP_NF_MATCH_STATE=m
CONFIG_IP_NF_MATCH_UNCLEAN=m
CONFIG_IP_NF_MATCH_OWNER=m
CONFIG_IP_NF_FILTER=m
CONFIG_IP_NF_TARGET_REJECT=m
CONFIG_IP_NF_TARGET_MIRROR=m
CONFIG_IP_NF_NAT=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_TARGET_MASQUERADE=m
CONFIG_IP_NF_TARGET_REDIRECT=m
CONFIG_IP_NF_NAT_FTP=m
CONFIG_IP_NF_MANGLE=m
CONFIG_IP_NF_TARGET_TOS=m
CONFIG_IP_NF_TARGET_MARK=m
CONFIG_IP_NF_TARGET_LOG=m
CONFIG_IP_NF_TARGET_TCPMSS=m
CONFIG_IP_NF_COMPAT_IPCHAINS=m
CONFIG_IP_NF_NAT_NEEDED=y
CONFIG_IP_NF_COMPAT_IPFWADM=m
CONFIG_IP_NF_NAT_NEEDED=y
# CONFIG_IPV6 is not set
# CONFIG_KHTTPD is not set
# CONFIG_ATM is not set
CONFIG_IPX=m
# CONFIG_IPX_INTERN is not set
# CONFIG_ATALK is not set
# CONFIG_DECNET is not set
CONFIG_BRIDGE=m
# CONFIG_X25 is not set
# CONFIG_LAPB is not set
# CONFIG_LLC is not set
# CONFIG_NET_DIVERT is not set
# CONFIG_ECONET is not set
# CONFIG_WAN_ROUTER is not set
# CONFIG_NET_FASTROUTE is not set
# CONFIG_NET_HW_FLOWCONTROL is not set
#
# QoS and/or fair queueing
#
CONFIG_NET_SCHED=y
CONFIG_NETLINK=y
CONFIG_RTNETLINK=y
CONFIG_NET_SCH_CBQ=m
CONFIG_NET_SCH_CSZ=m
CONFIG_NET_SCH_PRIO=m
CONFIG_NET_SCH_RED=m
CONFIG_NET_SCH_SFQ=m
CONFIG_NET_SCH_TEQL=m
CONFIG_NET_SCH_TBF=m
CONFIG_NET_SCH_GRED=m
CONFIG_NET_SCH_DSMARK=m
CONFIG_NET_SCH_INGRESS=m
CONFIG_NET_QOS=y
CONFIG_NET_ESTIMATOR=y
CONFIG_NET_CLS=y
CONFIG_NET_CLS_TCINDEX=m
CONFIG_NET_CLS_ROUTE4=m
CONFIG_NET_CLS_ROUTE=y
CONFIG_NET_CLS_FW=m
CONFIG_NET_CLS_U32=m
CONFIG_NET_CLS_RSVP=m
CONFIG_NET_CLS_RSVP6=m
CONFIG_NET_CLS_POLICE=y
#
# Telephony Support
#
# CONFIG_PHONE is not set
# CONFIG_PHONE_IXJ is not set
# CONFIG_PHONE_IXJ_PCMCIA is not set
#
# ATA/IDE/MFM/RLL support
#
CONFIG_IDE=y
#
# IDE, ATA and ATAPI Block devices
#
CONFIG_BLK_DEV_IDE=y
# CONFIG_BLK_DEV_HD_IDE is not set
# CONFIG_BLK_DEV_HD is not set
CONFIG_BLK_DEV_IDEDISK=y
# CONFIG_IDEDISK_MULTI_MODE is not set
# CONFIG_BLK_DEV_IDEDISK_VENDOR is not set
# CONFIG_BLK_DEV_IDEDISK_FUJITSU is not set
# CONFIG_BLK_DEV_IDEDISK_IBM is not set
# CONFIG_BLK_DEV_IDEDISK_MAXTOR is not set
# CONFIG_BLK_DEV_IDEDISK_QUANTUM is not set
# CONFIG_BLK_DEV_IDEDISK_SEAGATE is not set
# CONFIG_BLK_DEV_IDEDISK_WD is not set
# CONFIG_BLK_DEV_COMMERIAL is not set
# CONFIG_BLK_DEV_TIVO is not set
# CONFIG_BLK_DEV_IDECS is not set
CONFIG_BLK_DEV_IDECD=y
CONFIG_BLK_DEV_IDETAPE=m
CONFIG_BLK_DEV_IDEFLOPPY=y
CONFIG_BLK_DEV_IDESCSI=m
CONFIG_BLK_DEV_CMD640=y
CONFIG_BLK_DEV_CMD640_ENHANCED=y
CONFIG_BLK_DEV_ISAPNP=y
CONFIG_BLK_DEV_RZ1000=y
CONFIG_BLK_DEV_IDEPCI=y
CONFIG_IDEPCI_SHARE_IRQ=y
CONFIG_BLK_DEV_IDEDMA_PCI=y
CONFIG_BLK_DEV_ADMA=y
CONFIG_BLK_DEV_OFFBOARD=y
CONFIG_IDEDMA_PCI_AUTO=y
CONFIG_BLK_DEV_IDEDMA=y
# CONFIG_IDEDMA_PCI_WIP is not set
# CONFIG_IDEDMA_NEW_DRIVE_LISTINGS is not set
CONFIG_BLK_DEV_AEC62XX=y
CONFIG_AEC62XX_TUNING=y
CONFIG_BLK_DEV_ALI15X3=y
CONFIG_WDC_ALI15X3=y
# CONFIG_BLK_DEV_AMD74XX is not set
# CONFIG_AMD74XX_OVERRIDE is not set
CONFIG_BLK_DEV_CMD64X=y
CONFIG_BLK_DEV_CY82C693=y
CONFIG_BLK_DEV_CS5530=y
CONFIG_BLK_DEV_HPT34X=y
# CONFIG_HPT34X_AUTODMA is not set
CONFIG_BLK_DEV_HPT366=y
CONFIG_BLK_DEV_PIIX=y
# CONFIG_PIIX_TUNING is not set
CONFIG_BLK_DEV_NS87415=y
CONFIG_BLK_DEV_OPTI621=y
CONFIG_BLK_DEV_PDC202XX=y
CONFIG_PDC202XX_BURST=y
# CONFIG_PDC202XX_FORCE is not set
# CONFIG_BLK_DEV_SVWKS is not set
CONFIG_BLK_DEV_SIS5513=y
CONFIG_BLK_DEV_SLC90E66=y
CONFIG_BLK_DEV_TRM290=y
CONFIG_BLK_DEV_VIA82CXXX=y
CONFIG_IDE_CHIPSETS=y
CONFIG_BLK_DEV_4DRIVES=y
CONFIG_BLK_DEV_ALI14XX=y
CONFIG_BLK_DEV_DTC2278=y
CONFIG_BLK_DEV_HT6560B=y
CONFIG_BLK_DEV_PDC4030=y
# CONFIG_BLK_DEV_QD65XX is not set
CONFIG_BLK_DEV_UMC8672=y
CONFIG_IDEDMA_AUTO=y
CONFIG_IDEDMA_IVB=y
# CONFIG_DMA_NONPCI is not set
CONFIG_BLK_DEV_IDE_MODES=y
# CONFIG_BLK_DEV_ATARAID is not set
# CONFIG_BLK_DEV_ATARAID_PDC is not set
# CONFIG_BLK_DEV_ATARAID_HPT is not set
#
# SCSI support
#
CONFIG_SCSI=m
CONFIG_BLK_DEV_SD=m
CONFIG_SD_EXTRA_DEVS=40
CONFIG_CHR_DEV_ST=m
# CONFIG_CHR_DEV_OSST is not set
CONFIG_BLK_DEV_SR=m
CONFIG_BLK_DEV_SR_VENDOR=y
CONFIG_SR_EXTRA_DEVS=2
CONFIG_CHR_DEV_SG=m
# CONFIG_SCSI_DEBUG_QUEUES is not set
# CONFIG_SCSI_MULTI_LUN is not set
CONFIG_SCSI_CONSTANTS=y
CONFIG_SCSI_LOGGING=y
#
# SCSI low-level drivers
#
# CONFIG_BLK_DEV_3W_XXXX_RAID is not set
# CONFIG_SCSI_7000FASST is not set
# CONFIG_SCSI_ACARD is not set
# CONFIG_SCSI_AHA152X is not set
CONFIG_SCSI_AHA1542=m
# CONFIG_SCSI_AHA1740 is not set
CONFIG_SCSI_AIC7XXX=m
CONFIG_AIC7XXX_CMDS_PER_DEVICE=8
CONFIG_AIC7XXX_RESET_DELAY_MS=15000
CONFIG_AIC7XXX_BUILD_FIRMWARE=y
# CONFIG_SCSI_AIC7XXX_OLD is not set
# CONFIG_SCSI_DPT_I2O is not set
# CONFIG_SCSI_ADVANSYS is not set
# CONFIG_SCSI_IN2000 is not set
# CONFIG_SCSI_AM53C974 is not set
# CONFIG_SCSI_MEGARAID is not set
# CONFIG_SCSI_BUSLOGIC is not set
# CONFIG_SCSI_CPQFCTS is not set
# CONFIG_SCSI_DMX3191D is not set
# CONFIG_SCSI_DTC3280 is not set
CONFIG_SCSI_EATA=m
CONFIG_SCSI_EATA_TAGGED_QUEUE=y
# CONFIG_SCSI_EATA_LINKED_COMMANDS is not set
CONFIG_SCSI_EATA_MAX_TAGS=16
# CONFIG_SCSI_EATA_DMA is not set
# CONFIG_SCSI_EATA_PIO is not set
# CONFIG_SCSI_FUTURE_DOMAIN is not set
# CONFIG_SCSI_GDTH is not set
# CONFIG_SCSI_GENERIC_NCR5380 is not set
# CONFIG_SCSI_IPS is not set
# CONFIG_SCSI_INITIO is not set
# CONFIG_SCSI_INIA100 is not set
# CONFIG_SCSI_PPA is not set
# CONFIG_SCSI_IMM is not set
# CONFIG_SCSI_NCR53C406A is not set
# CONFIG_SCSI_NCR_D700 is not set
# CONFIG_SCSI_NCR53C7xx is not set
# CONFIG_SCSI_NCR53C8XX is not set
# CONFIG_SCSI_SYM53C8XX is not set
# CONFIG_SCSI_PAS16 is not set
# CONFIG_SCSI_PCI2000 is not set
# CONFIG_SCSI_PCI2220I is not set
# CONFIG_SCSI_PSI240I is not set
# CONFIG_SCSI_QLOGIC_FAS is not set
# CONFIG_SCSI_QLOGIC_ISP is not set
# CONFIG_SCSI_QLOGIC_FC is not set
# CONFIG_SCSI_QLOGIC_FC_FIRMWARE is not set
# CONFIG_SCSI_QLOGIC_1280 is not set
# CONFIG_SCSI_SEAGATE is not set
# CONFIG_SCSI_SIM710 is not set
# CONFIG_SCSI_SYM53C416 is not set
# CONFIG_SCSI_DC390T is not set
# CONFIG_SCSI_T128 is not set
# CONFIG_SCSI_U14_34F is not set
# CONFIG_SCSI_ULTRASTOR is not set
# CONFIG_SCSI_DEBUG is not set
#
# Fusion MPT device support
#
# CONFIG_FUSION is not set
# CONFIG_FUSION_BOOT is not set
# CONFIG_FUSION_ISENSE is not set
# CONFIG_FUSION_CTL is not set
# CONFIG_FUSION_LAN is not set
#
# IEEE 1394 (FireWire) support (EXPERIMENTAL)
#
# CONFIG_IEEE1394 is not set
#
# I2O device support
#
# CONFIG_I2O is not set
# CONFIG_I2O_PCI is not set
# CONFIG_I2O_BLOCK is not set
# CONFIG_I2O_LAN is not set
# CONFIG_I2O_SCSI is not set
# CONFIG_I2O_PROC is not set
#
# Network device support
#
CONFIG_NETDEVICES=y
#
# ARCnet devices
#
# CONFIG_ARCNET is not set
CONFIG_DUMMY=m
# CONFIG_BONDING is not set
# CONFIG_EQUALIZER is not set
CONFIG_TUN=m
# CONFIG_ETHERTAP is not set
# CONFIG_NET_SB1000 is not set
#
# Ethernet (10 or 100Mbit)
#
CONFIG_NET_ETHERNET=y
# CONFIG_SUNLANCE is not set
# CONFIG_HAPPYMEAL is not set
# CONFIG_SUNBMAC is not set
# CONFIG_SUNQE is not set
# CONFIG_SUNLANCE is not set
# CONFIG_SUNGEM is not set
# CONFIG_NET_VENDOR_3COM is not set
# CONFIG_LANCE is not set
# CONFIG_NET_VENDOR_SMC is not set
# CONFIG_NET_VENDOR_RACAL is not set
# CONFIG_AT1700 is not set
# CONFIG_DEPCA is not set
# CONFIG_HP100 is not set
CONFIG_NET_ISA=y
# CONFIG_E2100 is not set
# CONFIG_EWRK3 is not set
# CONFIG_EEXPRESS is not set
# CONFIG_EEXPRESS_PRO is not set
# CONFIG_HPLAN_PLUS is not set
# CONFIG_HPLAN is not set
# CONFIG_LP486E is not set
# CONFIG_ETH16I is not set
CONFIG_NE2000=m
CONFIG_NET_PCI=y
# CONFIG_PCNET32 is not set
# CONFIG_ADAPTEC_STARFIRE is not set
# CONFIG_AC3200 is not set
# CONFIG_APRICOT is not set
# CONFIG_CS89x0 is not set
# CONFIG_TULIP is not set
# CONFIG_DE4X5 is not set
# CONFIG_DGRS is not set
CONFIG_DM9102=m
# CONFIG_EEPRO100 is not set
# CONFIG_LNE390 is not set
# CONFIG_FEALNX is not set
# CONFIG_NATSEMI is not set
# CONFIG_NE2K_PCI is not set
# CONFIG_NE3210 is not set
# CONFIG_ES3210 is not set
# CONFIG_8139TOO is not set
# CONFIG_8139TOO_PIO is not set
# CONFIG_8139TOO_TUNE_TWISTER is not set
# CONFIG_8139TOO_8129 is not set
# CONFIG_SIS900 is not set
# CONFIG_EPIC100 is not set
# CONFIG_SUNDANCE is not set
# CONFIG_TLAN is not set
# CONFIG_VIA_RHINE is not set
# CONFIG_WINBOND_840 is not set
# CONFIG_NET_POCKET is not set
#
# Ethernet (1000 Mbit)
#
# CONFIG_ACENIC is not set
# CONFIG_DL2K is not set
# CONFIG_MYRI_SBUS is not set
# CONFIG_NS83820 is not set
# CONFIG_HAMACHI is not set
# CONFIG_YELLOWFIN is not set
# CONFIG_SK98LIN is not set
# CONFIG_FDDI is not set
# CONFIG_HIPPI is not set
# CONFIG_PLIP is not set
CONFIG_PPP=m
# CONFIG_PPP_MULTILINK is not set
# CONFIG_PPP_FILTER is not set
CONFIG_PPP_ASYNC=m
CONFIG_PPP_SYNC_TTY=m
CONFIG_PPP_DEFLATE=m
CONFIG_PPP_BSDCOMP=m
CONFIG_PPPOE=m
# CONFIG_SLIP is not set
#
# Wireless LAN (non-hamradio)
#
# CONFIG_NET_RADIO is not set
#
# Token Ring devices
#
# CONFIG_TR is not set
# CONFIG_NET_FC is not set
# CONFIG_RCPCI is not set
# CONFIG_SHAPER is not set
#
# Wan interfaces
#
# CONFIG_WAN is not set
#
# Amateur Radio support
#
# CONFIG_HAMRADIO is not set
#
# IrDA (infrared) support
#
# CONFIG_IRDA is not set
#
# ISDN subsystem
#
CONFIG_ISDN=m
CONFIG_ISDN_PPP=y
CONFIG_ISDN_PPP_VJ=y
CONFIG_ISDN_MPP=y
CONFIG_ISDN_PPP_BSDCOMP=m
CONFIG_ISDN_AUDIO=y
CONFIG_ISDN_TTY_FAX=y
#
# ISDN feature submodules
#
CONFIG_ISDN_DRV_LOOP=m
CONFIG_ISDN_DIVERSION=m
#
# Passive ISDN cards
#
CONFIG_ISDN_DRV_HISAX=m
CONFIG_HISAX_EURO=y
CONFIG_DE_AOC=y
# CONFIG_HISAX_NO_SENDCOMPLETE is not set
# CONFIG_HISAX_NO_LLC is not set
# CONFIG_HISAX_NO_KEYPAD is not set
# CONFIG_HISAX_1TR6 is not set
# CONFIG_HISAX_NI1 is not set
# CONFIG_HISAX_16_0 is not set
# CONFIG_HISAX_16_3 is not set
# CONFIG_HISAX_TELESPCI is not set
# CONFIG_HISAX_S0BOX is not set
# CONFIG_HISAX_AVM_A1 is not set
CONFIG_HISAX_FRITZPCI=y
# CONFIG_HISAX_AVM_A1_PCMCIA is not set
# CONFIG_HISAX_ELSA is not set
# CONFIG_HISAX_IX1MICROR2 is not set
# CONFIG_HISAX_DIEHLDIVA is not set
# CONFIG_HISAX_ASUSCOM is not set
# CONFIG_HISAX_TELEINT is not set
# CONFIG_HISAX_HFCS is not set
# CONFIG_HISAX_SEDLBAUER is not set
# CONFIG_HISAX_SPORTSTER is not set
# CONFIG_HISAX_MIC is not set
# CONFIG_HISAX_NETJET is not set
# CONFIG_HISAX_NETJET_U is not set
# CONFIG_HISAX_NICCY is not set
# CONFIG_HISAX_ISURF is not set
# CONFIG_HISAX_HSTSAPHIR is not set
# CONFIG_HISAX_BKM_A4T is not set
# CONFIG_HISAX_SCT_QUADRO is not set
# CONFIG_HISAX_GAZEL is not set
# CONFIG_HISAX_HFC_PCI is not set
# CONFIG_HISAX_W6692 is not set
# CONFIG_HISAX_HFC_SX is not set
# CONFIG_HISAX_SEDLBAUER_CS is not set
# CONFIG_HISAX_ELSA_CS is not set
#
# Active ISDN cards
#
# CONFIG_ISDN_DRV_ICN is not set
# CONFIG_ISDN_DRV_PCBIT is not set
# CONFIG_ISDN_DRV_SC is not set
# CONFIG_ISDN_DRV_ACT2000 is not set
# CONFIG_ISDN_DRV_EICON is not set
# CONFIG_ISDN_DRV_TPAM is not set
# CONFIG_ISDN_CAPI is not set
# CONFIG_HYSDN is not set
# CONFIG_HYSDN_CAPI is not set
#
# Old CD-ROM drivers (not SCSI, not IDE)
#
# CONFIG_CD_NO_IDESCSI is not set
#
# Input core support
#
CONFIG_INPUT=m
CONFIG_INPUT_KEYBDEV=m
CONFIG_INPUT_MOUSEDEV=m
CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
# CONFIG_INPUT_JOYDEV is not set
# CONFIG_INPUT_EVDEV is not set
#
# Character devices
#
CONFIG_VT=y
CONFIG_VT_CONSOLE=y
CONFIG_SERIAL=y
CONFIG_SERIAL_CONSOLE=y
CONFIG_SERIAL_EXTENDED=y
CONFIG_SERIAL_MANY_PORTS=y
CONFIG_SERIAL_SHARE_IRQ=y
# CONFIG_SERIAL_DETECT_IRQ is not set
CONFIG_SERIAL_MULTIPORT=y
# CONFIG_HUB6 is not set
# CONFIG_SERIAL_NONSTANDARD is not set
CONFIG_UNIX98_PTYS=y
CONFIG_UNIX98_PTY_COUNT=256
CONFIG_PRINTER=m
# CONFIG_LP_CONSOLE is not set
CONFIG_PPDEV=m
#
# I2C support
#
# CONFIG_I2C is not set
#
# Mice
#
CONFIG_BUSMOUSE=m
# CONFIG_ATIXL_BUSMOUSE is not set
CONFIG_LOGIBUSMOUSE=m
CONFIG_MS_BUSMOUSE=m
CONFIG_MOUSE=m
CONFIG_PSMOUSE=y
# CONFIG_82C710_MOUSE is not set
# CONFIG_PC110_PAD is not set
#
# Joysticks
#
# CONFIG_INPUT_GAMEPORT is not set
# CONFIG_INPUT_NS558 is not set
# CONFIG_INPUT_LIGHTNING is not set
# CONFIG_INPUT_PCIGAME is not set
# CONFIG_INPUT_CS461X is not set
# CONFIG_INPUT_EMU10K1 is not set
# CONFIG_INPUT_SERIO is not set
# CONFIG_INPUT_SERPORT is not set
# CONFIG_INPUT_ANALOG is not set
# CONFIG_INPUT_A3D is not set
# CONFIG_INPUT_ADI is not set
# CONFIG_INPUT_COBRA is not set
# CONFIG_INPUT_GF2K is not set
# CONFIG_INPUT_GRIP is not set
# CONFIG_INPUT_INTERACT is not set
# CONFIG_INPUT_TMDC is not set
# CONFIG_INPUT_SIDEWINDER is not set
# CONFIG_INPUT_IFORCE_USB is not set
# CONFIG_INPUT_IFORCE_232 is not set
# CONFIG_INPUT_WARRIOR is not set
# CONFIG_INPUT_MAGELLAN is not set
# CONFIG_INPUT_SPACEORB is not set
# CONFIG_INPUT_SPACEBALL is not set
# CONFIG_INPUT_STINGER is not set
# CONFIG_INPUT_DB9 is not set
# CONFIG_INPUT_GAMECON is not set
# CONFIG_INPUT_TURBOGRAFX is not set
# CONFIG_QIC02_TAPE is not set
#
# Watchdog Cards
#
# CONFIG_WATCHDOG is not set
# CONFIG_INTEL_RNG is not set
CONFIG_NVRAM=m
CONFIG_RTC=y
# CONFIG_DTLK is not set
# CONFIG_R3964 is not set
# CONFIG_APPLICOM is not set
# CONFIG_SONYPI is not set
#
# Ftape, the floppy tape device driver
#
# CONFIG_FTAPE is not set
CONFIG_AGP=m
CONFIG_AGP_INTEL=y
# CONFIG_AGP_I810 is not set
# CONFIG_AGP_VIA is not set
# CONFIG_AGP_AMD is not set
# CONFIG_AGP_SIS is not set
# CONFIG_AGP_ALI is not set
# CONFIG_AGP_SWORKS is not set
CONFIG_DRM=y
CONFIG_DRM_NEW=y
CONFIG_DRM_TDFX=y
# CONFIG_DRM_GAMMA is not set
# CONFIG_DRM_R128 is not set
# CONFIG_DRM_RADEON is not set
# CONFIG_DRM_I810 is not set
CONFIG_DRM_MGA=m
#
# Multimedia devices
#
# CONFIG_VIDEO_DEV is not set
#
# File systems
#
CONFIG_QUOTA=y
CONFIG_AUTOFS_FS=m
CONFIG_AUTOFS4_FS=m
CONFIG_REISERFS_FS=m
# CONFIG_REISERFS_CHECK is not set
# CONFIG_REISERFS_PROC_INFO is not set
# CONFIG_ADFS_FS is not set
# CONFIG_ADFS_FS_RW is not set
# CONFIG_AFFS_FS is not set
# CONFIG_HFS_FS is not set
# CONFIG_BFS_FS is not set
# CONFIG_CMS_FS is not set
# CONFIG_EXT3_FS is not set
# CONFIG_JBD is not set
# CONFIG_JBD_DEBUG is not set
CONFIG_FAT_FS=m
CONFIG_MSDOS_FS=m
CONFIG_UMSDOS_FS=m
CONFIG_VFAT_FS=m
# CONFIG_EFS_FS is not set
# CONFIG_JFFS_FS is not set
# CONFIG_JFFS2_FS is not set
CONFIG_CRAMFS=m
# CONFIG_TMPFS is not set
CONFIG_RAMFS=m
CONFIG_ISO9660_FS=m
CONFIG_JOLIET=y
CONFIG_MINIX_FS=m
# CONFIG_FREEVXFS_FS is not set
# CONFIG_NTFS_FS is not set
# CONFIG_NTFS_RW is not set
# CONFIG_HPFS_FS is not set
CONFIG_PROC_FS=y
# CONFIG_DEVFS_FS is not set
# CONFIG_DEVFS_MOUNT is not set
# CONFIG_DEVFS_DEBUG is not set
CONFIG_DEVPTS_FS=y
CONFIG_QNX4FS_FS=m
# CONFIG_QNX4FS_RW is not set
CONFIG_ROMFS_FS=m
CONFIG_EXT2_FS=y
# CONFIG_SYSV_FS is not set
CONFIG_UDF_FS=m
# CONFIG_UDF_RW is not set
# CONFIG_UFS_FS is not set
# CONFIG_UFS_FS_WRITE is not set
#
# Network File Systems
#
# CONFIG_CODA_FS is not set
# CONFIG_INTERMEZZO_FS is not set
# CONFIG_NFS_FS is not set
# CONFIG_NFS_V3 is not set
# CONFIG_ROOT_NFS is not set
# CONFIG_NFSD is not set
# CONFIG_NFSD_V3 is not set
# CONFIG_SUNRPC is not set
# CONFIG_LOCKD is not set
CONFIG_SMB_FS=m
CONFIG_SMB_NLS_DEFAULT=y
CONFIG_SMB_NLS_REMOTE="cp437"
# CONFIG_NCP_FS is not set
# CONFIG_NCPFS_PACKET_SIGNING is not set
# CONFIG_NCPFS_IOCTL_LOCKING is not set
# CONFIG_NCPFS_STRONG is not set
# CONFIG_NCPFS_NFS_NS is not set
# CONFIG_NCPFS_OS2_NS is not set
# CONFIG_NCPFS_SMALLDOS is not set
# CONFIG_NCPFS_NLS is not set
# CONFIG_NCPFS_EXTRAS is not set
#
# Partition Types
#
CONFIG_PARTITION_ADVANCED=y
# CONFIG_ACORN_PARTITION is not set
# CONFIG_OSF_PARTITION is not set
# CONFIG_AMIGA_PARTITION is not set
# CONFIG_ATARI_PARTITION is not set
# CONFIG_MAC_PARTITION is not set
CONFIG_MSDOS_PARTITION=y
# CONFIG_BSD_DISKLABEL is not set
# CONFIG_MINIX_SUBPARTITION is not set
# CONFIG_SOLARIS_X86_PARTITION is not set
# CONFIG_UNIXWARE_DISKLABEL is not set
# CONFIG_LDM_PARTITION is not set
# CONFIG_SGI_PARTITION is not set
# CONFIG_ULTRIX_PARTITION is not set
# CONFIG_SUN_PARTITION is not set
CONFIG_SMB_NLS=y
CONFIG_NLS=y
#
# Native Language Support
#
CONFIG_NLS_DEFAULT="iso8859-1"
CONFIG_NLS_CODEPAGE_437=m
CONFIG_NLS_CODEPAGE_737=m
CONFIG_NLS_CODEPAGE_775=m
CONFIG_NLS_CODEPAGE_850=m
CONFIG_NLS_CODEPAGE_852=m
CONFIG_NLS_CODEPAGE_855=m
CONFIG_NLS_CODEPAGE_857=m
CONFIG_NLS_CODEPAGE_860=m
CONFIG_NLS_CODEPAGE_861=m
CONFIG_NLS_CODEPAGE_862=m
CONFIG_NLS_CODEPAGE_863=m
CONFIG_NLS_CODEPAGE_864=m
CONFIG_NLS_CODEPAGE_865=m
CONFIG_NLS_CODEPAGE_866=m
CONFIG_NLS_CODEPAGE_869=m
CONFIG_NLS_CODEPAGE_936=m
CONFIG_NLS_CODEPAGE_950=m
CONFIG_NLS_CODEPAGE_932=m
CONFIG_NLS_CODEPAGE_949=m
CONFIG_NLS_CODEPAGE_874=m
CONFIG_NLS_ISO8859_8=m
CONFIG_NLS_CODEPAGE_1251=m
CONFIG_NLS_ISO8859_1=m
CONFIG_NLS_ISO8859_2=m
CONFIG_NLS_ISO8859_3=m
CONFIG_NLS_ISO8859_4=m
CONFIG_NLS_ISO8859_5=m
CONFIG_NLS_ISO8859_6=m
CONFIG_NLS_ISO8859_7=m
CONFIG_NLS_ISO8859_9=m
CONFIG_NLS_ISO8859_13=m
CONFIG_NLS_ISO8859_14=m
CONFIG_NLS_ISO8859_15=m
CONFIG_NLS_KOI8_R=m
CONFIG_NLS_KOI8_U=m
CONFIG_NLS_UTF8=m
#
# Console drivers
#
CONFIG_VGA_CONSOLE=y
CONFIG_VIDEO_SELECT=y
# CONFIG_MDA_CONSOLE is not set
#
# Frame-buffer support
#
CONFIG_FB=y
CONFIG_DUMMY_CONSOLE=y
CONFIG_FB_RIVA=y
# CONFIG_FB_CLGEN is not set
# CONFIG_FB_PM2 is not set
# CONFIG_FB_CYBER2000 is not set
CONFIG_FB_VESA=y
CONFIG_FB_VGA16=m
CONFIG_FB_HGA=m
CONFIG_VIDEO_SELECT=y
# CONFIG_FB_E1355 is not set
# CONFIG_FB_MATROX is not set
CONFIG_FB_ATY=m
# CONFIG_FB_ATY_GX is not set
# CONFIG_FB_ATY_CT is not set
# CONFIG_FB_RADEON is not set
# CONFIG_FB_ATY128 is not set
# CONFIG_FB_SIS is not set
# CONFIG_FB_3DFX is not set
CONFIG_FB_VIRTUAL=m
# CONFIG_FBCON_ADVANCED is not set
CONFIG_FBCON_MFB=m
CONFIG_FBCON_CFB2=m
CONFIG_FBCON_CFB4=m
CONFIG_FBCON_CFB8=y
CONFIG_FBCON_CFB16=y
CONFIG_FBCON_CFB24=y
CONFIG_FBCON_CFB32=y
CONFIG_FBCON_MAC=m
CONFIG_FBCON_VGA_PLANES=m
CONFIG_FBCON_HGA=m
# CONFIG_FBCON_FONTWIDTH8_ONLY is not set
# CONFIG_FBCON_FONTS is not set
CONFIG_FONT_8x8=y
CONFIG_FONT_8x16=y
#
# Sound
#
CONFIG_SOUND=m
# CONFIG_SOUND_BT878 is not set
# CONFIG_SOUND_CMPCI is not set
# CONFIG_SOUND_EMU10K1 is not set
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
CONFIG_SOUND_ES1370=m
CONFIG_SOUND_ES1371=m
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_MAESTRO3 is not set
# CONFIG_SOUND_ICH is not set
# CONFIG_SOUND_RME96XX is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_MIDI_VIA82CXXX is not set
CONFIG_SOUND_OSS=m
CONFIG_SOUND_TRACEINIT=y
CONFIG_SOUND_DMAP=y
# CONFIG_SOUND_AD1816 is not set
# CONFIG_SOUND_SGALAXY is not set
# CONFIG_SOUND_ADLIB is not set
# CONFIG_SOUND_ACI_MIXER is not set
# CONFIG_SOUND_CS4232 is not set
CONFIG_SOUND_SSCAPE=m
# CONFIG_SOUND_GUS is not set
CONFIG_SOUND_VMIDI=m
# CONFIG_SOUND_TRIX is not set
# CONFIG_SOUND_MSS is not set
# CONFIG_SOUND_MPU401 is not set
# CONFIG_SOUND_NM256 is not set
# CONFIG_SOUND_MAD16 is not set
# CONFIG_SOUND_PAS is not set
# CONFIG_PAS_JOYSTICK is not set
# CONFIG_SOUND_PSS is not set
CONFIG_SOUND_SB=m
CONFIG_SOUND_AWE32_SYNTH=m
# CONFIG_SOUND_WAVEFRONT is not set
# CONFIG_SOUND_MAUI is not set
# CONFIG_SOUND_YM3812 is not set
# CONFIG_SOUND_OPL3SA1 is not set
# CONFIG_SOUND_OPL3SA2 is not set
# CONFIG_SOUND_YMFPCI is not set
# CONFIG_SOUND_YMFPCI_LEGACY is not set
CONFIG_SOUND_UART6850=m
# CONFIG_SOUND_AEDSP16 is not set
# CONFIG_SOUND_TVMIXER is not set
?
#
# USB support
#
CONFIG_USB=m
# CONFIG_USB_DEBUG is not set
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_LONG_TIMEOUT is not set
# CONFIG_USB_LARGE_CONFIG is not set
CONFIG_USB_UHCI=m
# CONFIG_USB_UHCI_ALT is not set
# CONFIG_USB_OHCI is not set
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_BLUETOOTH is not set
# CONFIG_USB_STORAGE is not set
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_ACM is not set
# CONFIG_USB_PRINTER is not set
# CONFIG_USB_HID is not set
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_KBD is not set
CONFIG_USB_MOUSE=m
# CONFIG_USB_WACOM is not set
# CONFIG_USB_DC2XX is not set
# CONFIG_USB_MDC800 is not set
CONFIG_USB_SCANNER=m
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set
# CONFIG_USB_DABUSB is not set
# CONFIG_USB_PLUSB is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_CATC is not set
# CONFIG_USB_CDCETHER is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_USS720 is not set
?
#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
# CONFIG_USB_SERIAL_GENERIC is not set
# CONFIG_USB_SERIAL_BELKIN is not set
# CONFIG_USB_SERIAL_WHITEHEAT is not set
# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
# CONFIG_USB_SERIAL_EMPEG is not set
# CONFIG_USB_SERIAL_FTDI_SIO is not set
# CONFIG_USB_SERIAL_VISOR is not set
# CONFIG_USB_SERIAL_EDGEPORT is not set
# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
# CONFIG_USB_SERIAL_KEYSPAN is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28 is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA28X is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA19 is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA18X is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA19W is not set
# CONFIG_USB_SERIAL_KEYSPAN_USA49W is not set
# CONFIG_USB_SERIAL_MCT_U232 is not set
# CONFIG_USB_SERIAL_PL2303 is not set
# CONFIG_USB_SERIAL_CYBERJACK is not set
# CONFIG_USB_SERIAL_OMNINET is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_ID75 is not set
?
#
# Bluetooth support
#
# CONFIG_BLUEZ is not set
?
#
# Kernel hacking
#
# CONFIG_DEBUG_KERNEL is not set