Update the vkms documentation to contain steps to:
- setup the vkms driver
- run tests using igt
Signed-off-by: Sumera Priyadarsini <[email protected]>
---
Documentation/gpu/vkms.rst | 47 ++++++++++++++++++++++++++++++++++++++
1 file changed, 47 insertions(+)
diff --git a/Documentation/gpu/vkms.rst b/Documentation/gpu/vkms.rst
index 13bab1d93bb3..d6782174d23f 100644
--- a/Documentation/gpu/vkms.rst
+++ b/Documentation/gpu/vkms.rst
@@ -7,6 +7,53 @@
.. kernel-doc:: drivers/gpu/drm/vkms/vkms_drv.c
:doc: vkms (Virtual Kernel Modesetting)
+SETUP
+=====
+
+The VKMS driver can be setup with the following steps:
+
+To check if VKMS is loaded, run::
+
+ lsmod | grep vkms
+
+This should list the VKMS driver. If no output is obtained, then
+you need to enable and/or load the VKMS driver.
+Ensure that the VKMS driver has been set as a loadable module in your
+kernel config file. The following line should be present in the .config
+file in your kernel root::
+
+ CONFIG_DRM_VKMS=m
+
+Compile and build the kernel for the changes to get reflected.
+If your existing config already has VKMS available as a loadable module,
+then there is no need to build the kernel again.
+Now, to load the driver, use::
+
+ sudo modprobe vkms
+
+On running the lsmod command now, the VKMS driver will appear listed.
+You can also observe the driver being loaded in the dmesg logs.
+
+To disable the driver, use ::
+
+ sudo modprobe -r vkms
+
+TESTING WITH IGT
+================
+
+The IGT GPU Tools is a test suite used specifically for debugging and
+development of the DRM drivers.
+The IGT Tools can be installed from
+`here <https://gitlab.freedesktop.org/drm/igt-gpu-tools>`_ .
+Once you have installed IGT, you can run tests using::
+
+ ./scripts/run-tests.sh -t <name of test>
+
+For example, to test the functionality of the igt_draw library,
+we can run the kms_draw_crc test::
+
+ ./scripts/run-tests.sh -t kms_draw_crc
+
TODO
====
--
2.25.1
On Thu, Dec 3, 2020 at 8:13 PM Sumera Priyadarsini
<[email protected]> wrote:
>
> Update the vkms documentation to contain steps to:
>
> - setup the vkms driver
> - run tests using igt
>
> Signed-off-by: Sumera Priyadarsini <[email protected]>
> ---
> Documentation/gpu/vkms.rst | 47 ++++++++++++++++++++++++++++++++++++++
> 1 file changed, 47 insertions(+)
>
> diff --git a/Documentation/gpu/vkms.rst b/Documentation/gpu/vkms.rst
> index 13bab1d93bb3..d6782174d23f 100644
> --- a/Documentation/gpu/vkms.rst
> +++ b/Documentation/gpu/vkms.rst
> @@ -7,6 +7,53 @@
> .. kernel-doc:: drivers/gpu/drm/vkms/vkms_drv.c
> :doc: vkms (Virtual Kernel Modesetting)
>
> +SETUP
Absolute bikeshed, but we generally stick to titlecase for titles, so
just "Setup" and "Testing with IGT".
> +=====
> +
> +The VKMS driver can be setup with the following steps:
> +
> +To check if VKMS is loaded, run::
> +
> + lsmod | grep vkms
> +
> +This should list the VKMS driver. If no output is obtained, then
> +you need to enable and/or load the VKMS driver.
> +Ensure that the VKMS driver has been set as a loadable module in your
> +kernel config file. The following line should be present in the .config
> +file in your kernel root::
> +
> + CONFIG_DRM_VKMS=m
> +
> +Compile and build the kernel for the changes to get reflected.
> +If your existing config already has VKMS available as a loadable module,
> +then there is no need to build the kernel again.
> +Now, to load the driver, use::
> +
> + sudo modprobe vkms
> +
> +On running the lsmod command now, the VKMS driver will appear listed.
> +You can also observe the driver being loaded in the dmesg logs.
> +
> +To disable the driver, use ::
> +
> + sudo modprobe -r vkms
> +
> +TESTING WITH IGT
> +================
> +
> +The IGT GPU Tools is a test suite used specifically for debugging and
> +development of the DRM drivers.
> +The IGT Tools can be installed from
> +`here <https://gitlab.freedesktop.org/drm/igt-gpu-tools>`_ .
> +Once you have installed IGT, you can run tests using::
> +
> + ./scripts/run-tests.sh -t <name of test>
> +
> +For example, to test the functionality of the igt_draw library,
> +we can run the kms_draw_crc test::
> +
> + ./scripts/run-tests.sh -t kms_draw_crc
If we run igt tests directly, there's an option to select the right
device. This is important if you have more than one gpu driver
(usually the case if you run this directly, but even on virtual
machines there should usually be a drm driver around). E.g. when I
run a test directly:
# tests/kms_flip --device drm:/dev/dri/card0
I'm not sure whether there's an option that's always going to select
the vkms device. I'm also not sure you can pass these options to
run-tests.sh, I kinda don't use that one myself ...
Aside from that looks all good to me.
-Daniel
> +
> TODO
> ====
>
> --
> 2.25.1
>
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
Hi Sumera,
Thanks for the doc improvements.
Please see some complimentary comments below.
On 12/03, Daniel Vetter wrote:
> On Thu, Dec 3, 2020 at 8:13 PM Sumera Priyadarsini
> <[email protected]> wrote:
> >
> > Update the vkms documentation to contain steps to:
> >
> > - setup the vkms driver
> > - run tests using igt
> >
> > Signed-off-by: Sumera Priyadarsini <[email protected]>
> > ---
> > Documentation/gpu/vkms.rst | 47 ++++++++++++++++++++++++++++++++++++++
> > 1 file changed, 47 insertions(+)
> >
> > diff --git a/Documentation/gpu/vkms.rst b/Documentation/gpu/vkms.rst
> > index 13bab1d93bb3..d6782174d23f 100644
> > --- a/Documentation/gpu/vkms.rst
> > +++ b/Documentation/gpu/vkms.rst
> > @@ -7,6 +7,53 @@
> > .. kernel-doc:: drivers/gpu/drm/vkms/vkms_drv.c
> > :doc: vkms (Virtual Kernel Modesetting)
> >
> > +SETUP
>
> Absolute bikeshed, but we generally stick to titlecase for titles, so
> just "Setup" and "Testing with IGT".
> > +=====
> > +
> > +The VKMS driver can be setup with the following steps:
> > +
> > +To check if VKMS is loaded, run::
> > +
> > + lsmod | grep vkms
> > +
> > +This should list the VKMS driver. If no output is obtained, then
> > +you need to enable and/or load the VKMS driver.
> > +Ensure that the VKMS driver has been set as a loadable module in your
> > +kernel config file. The following line should be present in the .config
> > +file in your kernel root::
> > +
> > + CONFIG_DRM_VKMS=m
> > +
Considering the target audience, I would make it clearer to explore the
configuration options using "make *config". As in
https://kernelnewbies.org/FirstKernelPatch#Recompiling_the_driver
> > +Compile and build the kernel for the changes to get reflected.
> > +If your existing config already has VKMS available as a loadable module,
> > +then there is no need to build the kernel again.
> > +Now, to load the driver, use::
> > +
> > + sudo modprobe vkms
> > +
> > +On running the lsmod command now, the VKMS driver will appear listed.
> > +You can also observe the driver being loaded in the dmesg logs.
> > +
> > +To disable the driver, use ::
s/disable/unload/
> > +
> > + sudo modprobe -r vkms
> > +
> > +TESTING WITH IGT
> > +================
> > +
> > +The IGT GPU Tools is a test suite used specifically for debugging and
> > +development of the DRM drivers.
> > +The IGT Tools can be installed from
> > +`here <https://gitlab.freedesktop.org/drm/igt-gpu-tools>`_ .
> > +Once you have installed IGT, you can run tests using::
> > +
> > + ./scripts/run-tests.sh -t <name of test>
> > +
> > +For example, to test the functionality of the igt_draw library,
> > +we can run the kms_draw_crc test::
> > +
> > + ./scripts/run-tests.sh -t kms_draw_crc
>
> If we run igt tests directly, there's an option to select the right
> device. This is important if you have more than one gpu driver
> (usually the case if you run this directly, but even on virtual
> machines there should usually be a drm driver around). E.g. when I
> run a test directly:
>
> # tests/kms_flip --device drm:/dev/dri/card0
>
> I'm not sure whether there's an option that's always going to select
> the vkms device. I'm also not sure you can pass these options to
> run-tests.sh, I kinda don't use that one myself ...
I also run a test directly. Some cases have many subtests, therefore I
can pass --run-subtest to specify one.
And, to select vkms, I use IGT_FORCE_DRIVER. For example:
# IGT_FORCE_DRIVER=vkms tests/kms_flip --run-subtest basic-plain-flip
>
> Aside from that looks all good to me.
+1
Melissa
> -Daniel
>
> > +
> > TODO
> > ====
> >
> > --
> > 2.25.1
> >
>
>
> --
> Daniel Vetter
> Software Engineer, Intel Corporation
> http://blog.ffwll.ch