Ceiling value may be miss-aligned with what's actually configured into the
ARR register. This is seen after probe as currently the ARR value is zero,
whereas ceiling value is set to the maximum. So:
- reading ceiling reports zero
- in case the counter gets enabled without any prior configuration,
it won't count.
- in case the function gets set by the user 1st, (priv->ceiling) is used.
Fix it by getting rid of the cached "priv->ceiling" variable. Rather use
the ARR register value directly by using regmap read or write when needed.
There should be no drawback on performance as priv->ceiling isn't used in
performance critical path.
There's also no point in writing ARR while setting function (sms), so
it can be safely removed.
Fixes: ad29937e206f ("counter: Add STM32 Timer quadrature encoder")
Suggested-by: William Breathitt Gray <[email protected]>
Signed-off-by: Fabrice Gasnier <[email protected]>
---
Note: this applies on top of:
- "counter: stm32-timer-cnt: fix ceiling write max value"
---
drivers/counter/stm32-timer-cnt.c | 11 +++--------
1 file changed, 3 insertions(+), 8 deletions(-)
diff --git a/drivers/counter/stm32-timer-cnt.c b/drivers/counter/stm32-timer-cnt.c
index 2295be3..75bc401 100644
--- a/drivers/counter/stm32-timer-cnt.c
+++ b/drivers/counter/stm32-timer-cnt.c
@@ -31,7 +31,6 @@ struct stm32_timer_cnt {
struct counter_device counter;
struct regmap *regmap;
struct clk *clk;
- u32 ceiling;
u32 max_arr;
bool enabled;
struct stm32_timer_regs bak;
@@ -75,8 +74,10 @@ static int stm32_count_write(struct counter_device *counter,
const unsigned long val)
{
struct stm32_timer_cnt *const priv = counter->priv;
+ u32 ceiling;
- if (val > priv->ceiling)
+ regmap_read(priv->regmap, TIM_ARR, &ceiling);
+ if (val > ceiling)
return -EINVAL;
return regmap_write(priv->regmap, TIM_CNT, val);
@@ -138,10 +139,6 @@ static int stm32_count_function_set(struct counter_device *counter,
regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN, 0);
- /* TIMx_ARR register shouldn't be buffered (ARPE=0) */
- regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_ARPE, 0);
- regmap_write(priv->regmap, TIM_ARR, priv->ceiling);
-
regmap_update_bits(priv->regmap, TIM_SMCR, TIM_SMCR_SMS, sms);
/* Make sure that registers are updated */
@@ -199,7 +196,6 @@ static ssize_t stm32_count_ceiling_write(struct counter_device *counter,
regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_ARPE, 0);
regmap_write(priv->regmap, TIM_ARR, ceiling);
- priv->ceiling = ceiling;
return len;
}
@@ -374,7 +370,6 @@ static int stm32_timer_cnt_probe(struct platform_device *pdev)
priv->regmap = ddata->regmap;
priv->clk = ddata->clk;
- priv->ceiling = ddata->max_arr;
priv->max_arr = ddata->max_arr;
priv->counter.name = dev_name(dev);
--
2.7.4
On Wed, Mar 03, 2021 at 06:49:49PM +0100, Fabrice Gasnier wrote:
> Ceiling value may be miss-aligned with what's actually configured into the
> ARR register. This is seen after probe as currently the ARR value is zero,
> whereas ceiling value is set to the maximum. So:
> - reading ceiling reports zero
> - in case the counter gets enabled without any prior configuration,
> it won't count.
> - in case the function gets set by the user 1st, (priv->ceiling) is used.
>
> Fix it by getting rid of the cached "priv->ceiling" variable. Rather use
> the ARR register value directly by using regmap read or write when needed.
> There should be no drawback on performance as priv->ceiling isn't used in
> performance critical path.
> There's also no point in writing ARR while setting function (sms), so
> it can be safely removed.
>
> Fixes: ad29937e206f ("counter: Add STM32 Timer quadrature encoder")
>
> Suggested-by: William Breathitt Gray <[email protected]>
> Signed-off-by: Fabrice Gasnier <[email protected]>
Acked-by: William Breathitt Gray <[email protected]>
> ---
> Note: this applies on top of:
> - "counter: stm32-timer-cnt: fix ceiling write max value"
Note, if your patch requires prerequisite patches, please provide the
`git patch-id --stable` patch ID for it; this helps make sure the
patches are applied in the correct order. You can have `git
format-patch` generate this automatically for you by using the `--base`
option:
https://git-scm.com/docs/git-format-patch#_base_tree_information
William Breathitt Gray
> ---
> drivers/counter/stm32-timer-cnt.c | 11 +++--------
> 1 file changed, 3 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/counter/stm32-timer-cnt.c b/drivers/counter/stm32-timer-cnt.c
> index 2295be3..75bc401 100644
> --- a/drivers/counter/stm32-timer-cnt.c
> +++ b/drivers/counter/stm32-timer-cnt.c
> @@ -31,7 +31,6 @@ struct stm32_timer_cnt {
> struct counter_device counter;
> struct regmap *regmap;
> struct clk *clk;
> - u32 ceiling;
> u32 max_arr;
> bool enabled;
> struct stm32_timer_regs bak;
> @@ -75,8 +74,10 @@ static int stm32_count_write(struct counter_device *counter,
> const unsigned long val)
> {
> struct stm32_timer_cnt *const priv = counter->priv;
> + u32 ceiling;
>
> - if (val > priv->ceiling)
> + regmap_read(priv->regmap, TIM_ARR, &ceiling);
> + if (val > ceiling)
> return -EINVAL;
>
> return regmap_write(priv->regmap, TIM_CNT, val);
> @@ -138,10 +139,6 @@ static int stm32_count_function_set(struct counter_device *counter,
>
> regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN, 0);
>
> - /* TIMx_ARR register shouldn't be buffered (ARPE=0) */
> - regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_ARPE, 0);
> - regmap_write(priv->regmap, TIM_ARR, priv->ceiling);
> -
> regmap_update_bits(priv->regmap, TIM_SMCR, TIM_SMCR_SMS, sms);
>
> /* Make sure that registers are updated */
> @@ -199,7 +196,6 @@ static ssize_t stm32_count_ceiling_write(struct counter_device *counter,
> regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_ARPE, 0);
> regmap_write(priv->regmap, TIM_ARR, ceiling);
>
> - priv->ceiling = ceiling;
> return len;
> }
>
> @@ -374,7 +370,6 @@ static int stm32_timer_cnt_probe(struct platform_device *pdev)
>
> priv->regmap = ddata->regmap;
> priv->clk = ddata->clk;
> - priv->ceiling = ddata->max_arr;
> priv->max_arr = ddata->max_arr;
>
> priv->counter.name = dev_name(dev);
> --
> 2.7.4
>
On Thu, 4 Mar 2021 08:42:03 +0900
William Breathitt Gray <[email protected]> wrote:
> On Wed, Mar 03, 2021 at 06:49:49PM +0100, Fabrice Gasnier wrote:
> > Ceiling value may be miss-aligned with what's actually configured into the
> > ARR register. This is seen after probe as currently the ARR value is zero,
> > whereas ceiling value is set to the maximum. So:
> > - reading ceiling reports zero
> > - in case the counter gets enabled without any prior configuration,
> > it won't count.
> > - in case the function gets set by the user 1st, (priv->ceiling) is used.
> >
> > Fix it by getting rid of the cached "priv->ceiling" variable. Rather use
> > the ARR register value directly by using regmap read or write when needed.
> > There should be no drawback on performance as priv->ceiling isn't used in
> > performance critical path.
> > There's also no point in writing ARR while setting function (sms), so
> > it can be safely removed.
> >
> > Fixes: ad29937e206f ("counter: Add STM32 Timer quadrature encoder")
Note, I've dropped the blank line here. Fixes is part of the tag block.
> >
> > Suggested-by: William Breathitt Gray <[email protected]>
> > Signed-off-by: Fabrice Gasnier <[email protected]>
>
> Acked-by: William Breathitt Gray <[email protected]>
applied to the fixes-togreg branch of iio.git and marked for stable.
Given both this and previous are marked such they should get picked
up fine even without the clean cross reference.
Jonathan
>
> > ---
> > Note: this applies on top of:
> > - "counter: stm32-timer-cnt: fix ceiling write max value"
>
> Note, if your patch requires prerequisite patches, please provide the
> `git patch-id --stable` patch ID for it; this helps make sure the
> patches are applied in the correct order. You can have `git
> format-patch` generate this automatically for you by using the `--base`
> option:
> https://git-scm.com/docs/git-format-patch#_base_tree_information
>
> William Breathitt Gray
>
> > ---
> > drivers/counter/stm32-timer-cnt.c | 11 +++--------
> > 1 file changed, 3 insertions(+), 8 deletions(-)
> >
> > diff --git a/drivers/counter/stm32-timer-cnt.c b/drivers/counter/stm32-timer-cnt.c
> > index 2295be3..75bc401 100644
> > --- a/drivers/counter/stm32-timer-cnt.c
> > +++ b/drivers/counter/stm32-timer-cnt.c
> > @@ -31,7 +31,6 @@ struct stm32_timer_cnt {
> > struct counter_device counter;
> > struct regmap *regmap;
> > struct clk *clk;
> > - u32 ceiling;
> > u32 max_arr;
> > bool enabled;
> > struct stm32_timer_regs bak;
> > @@ -75,8 +74,10 @@ static int stm32_count_write(struct counter_device *counter,
> > const unsigned long val)
> > {
> > struct stm32_timer_cnt *const priv = counter->priv;
> > + u32 ceiling;
> >
> > - if (val > priv->ceiling)
> > + regmap_read(priv->regmap, TIM_ARR, &ceiling);
> > + if (val > ceiling)
> > return -EINVAL;
> >
> > return regmap_write(priv->regmap, TIM_CNT, val);
> > @@ -138,10 +139,6 @@ static int stm32_count_function_set(struct counter_device *counter,
> >
> > regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_CEN, 0);
> >
> > - /* TIMx_ARR register shouldn't be buffered (ARPE=0) */
> > - regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_ARPE, 0);
> > - regmap_write(priv->regmap, TIM_ARR, priv->ceiling);
> > -
> > regmap_update_bits(priv->regmap, TIM_SMCR, TIM_SMCR_SMS, sms);
> >
> > /* Make sure that registers are updated */
> > @@ -199,7 +196,6 @@ static ssize_t stm32_count_ceiling_write(struct counter_device *counter,
> > regmap_update_bits(priv->regmap, TIM_CR1, TIM_CR1_ARPE, 0);
> > regmap_write(priv->regmap, TIM_ARR, ceiling);
> >
> > - priv->ceiling = ceiling;
> > return len;
> > }
> >
> > @@ -374,7 +370,6 @@ static int stm32_timer_cnt_probe(struct platform_device *pdev)
> >
> > priv->regmap = ddata->regmap;
> > priv->clk = ddata->clk;
> > - priv->ceiling = ddata->max_arr;
> > priv->max_arr = ddata->max_arr;
> >
> > priv->counter.name = dev_name(dev);
> > --
> > 2.7.4
> >