Changes the obsolete Scsi_Cmnd to struct scsi_cmnd and remove the trailing
whitespaces.
Signed-off-by: Henrik Kretzschmar <[email protected]>
---
diff --git a/drivers/scsi/t128.h b/drivers/scsi/t128.h
index 646e840..76a069b 100644
--- a/drivers/scsi/t128.h
+++ b/drivers/scsi/t128.h
@@ -8,20 +8,20 @@
* [email protected]
* +1 (303) 440-4894
*
- * DISTRIBUTION RELEASE 3.
+ * DISTRIBUTION RELEASE 3.
*
- * For more information, please consult
+ * For more information, please consult
*
* Trantor Systems, Ltd.
* T128/T128F/T228 SCSI Host Adapter
* Hardware Specifications
- *
- * Trantor Systems, Ltd.
+ *
+ * Trantor Systems, Ltd.
* 5415 Randall Place
* Fremont, CA 94538
* 1+ (415) 770-1400, FAX 1+ (415) 770-9910
- *
- * and
+ *
+ * and
*
* NCR 5380 Family
* SCSI Protocol Controller
@@ -48,15 +48,15 @@ #define TDEBUG_INIT 0x1
#define TDEBUG_TRANSFER 0x2
/*
- * The trantor boards are memory mapped. They use an NCR5380 or
+ * The trantor boards are memory mapped. They use an NCR5380 or
* equivalent (my sample board had part second sourced from ZILOG).
- * NCR's recommended "Pseudo-DMA" architecture is used, where
+ * NCR's recommended "Pseudo-DMA" architecture is used, where
* a PAL drives the DMA signals on the 5380 allowing fast, blind
- * transfers with proper handshaking.
+ * transfers with proper handshaking.
*/
/*
- * Note : a boot switch is provided for the purpose of informing the
+ * Note : a boot switch is provided for the purpose of informing the
* firmware to boot or not boot from attached SCSI devices. So, I imagine
* there are fewer people who've yanked the ROM like they do on the Seagate
* to make bootup faster, and I'll probably use this for autodetection.
@@ -92,19 +92,20 @@ #define T_5380_OFFSET 0x1d00 /* 8 regis
#define T_DATA_REG_OFFSET 0x1e00 /* rw 512 bytes long */
#ifndef ASM
-static int t128_abort(Scsi_Cmnd *);
+static int t128_abort(struct scsi_cmnd *);
static int t128_biosparam(struct scsi_device *, struct block_device *,
sector_t, int*);
static int t128_detect(struct scsi_host_template *);
-static int t128_queue_command(Scsi_Cmnd *, void (*done)(Scsi_Cmnd *));
-static int t128_bus_reset(Scsi_Cmnd *);
+static int t128_queue_command(struct scsi_cmnd *,
+ void (*done)(struct scsi_cmnd *));
+static int t128_bus_reset(struct scsi_cmnd *);
#ifndef CMD_PER_LUN
#define CMD_PER_LUN 2
#endif
#ifndef CAN_QUEUE
-#define CAN_QUEUE 32
+#define CAN_QUEUE 32
#endif
#ifndef HOSTS_C
@@ -120,7 +121,7 @@ #define NCR5380_setup(instance) \
#define T128_address(reg) (base + T_5380_OFFSET + ((reg) * 0x20))
-#if !(TDEBUG & TDEBUG_TRANSFER)
+#if !(TDEBUG & TDEBUG_TRANSFER)
#define NCR5380_read(reg) readb(T128_address(reg))
#define NCR5380_write(reg, value) writeb((value),(T128_address(reg)))
#else
@@ -129,7 +130,7 @@ #define NCR5380_read(reg) \
, instance->hostno, (reg), T128_address(reg))), readb(T128_address(reg)))
#define NCR5380_write(reg, value) { \
- printk("scsi%d : write %02x to register %d at address %08x\n", \
+ printk("scsi%d : write %02x to register %d at address %08x\n", \
instance->hostno, (value), (reg), T128_address(reg)); \
writeb((value), (T128_address(reg))); \
}
@@ -142,10 +143,10 @@ #define NCR5380_abort t128_abort
#define NCR5380_bus_reset t128_bus_reset
#define NCR5380_proc_info t128_proc_info
-/* 15 14 12 10 7 5 3
+/* 15 14 12 10 7 5 3
1101 0100 1010 1000 */
-
-#define T128_IRQS 0xc4a8
+
+#define T128_IRQS 0xc4a8
#endif /* else def HOSTS_C */
#endif /* ndef ASM */