Hi all,
After merging the hwmon-staging tree, today's linux-next build (htmldocs)
produced these warnings:
Documentation/hwmon/lt7182s.rst:2: WARNING: Explicit markup ends without a blank line; unexpected unindent.
Documentation/hwmon/lt7182s.rst:75: WARNING: Malformed table.
Text in column margin in table line 33.
====================== ====================================
curr[1-2]_label "iin[12]"
curr[1-2]_input Measured input current
curr[1-2]_max Maximum input current
curr[1-2]_max_alarm Current high alarm
curr[3-4]_label "iout[1-2]"
curr[3-4]_input Measured output current
curr[3-4]_highest Highest measured output current
curr[3-4]_max Maximum output current
curr[3-4]_max_alarm Output current high alarm
in[1-2]_label "vin[12]"
in[1-2]_input Measured input voltage
in[1-2]_highest Highest measured input voltage
in[1-2]_crit Critical maximum input voltage
in[1-2]_crit_alarm Input voltage critical high alarm
in[1-2]_min Minimum input voltage
in[1-2]_min_alarm Input voltage low alarm
in[1-2]_rated_min Rated minimum input voltage
in[1-2]_rated_max Rated maximum input voltage
in1_reset_history Write to reset history for all attributes
in[3-5]_label "vmon[1-3]"
in[3-5]_input Measured voltage on ITH1/ITH2/EXTVCC pins
Only available if enabled with MFR_ADC_CONTROL_LT7182S
command.
in[3-4|6-7]_label "vout[1-2]"
in[3-4|6-7]_input Measured output voltage
in[3-4|6-7]_highest Highest measured output voltage
in[3-4|6-7]_lcrit Critical minimum output voltage
in[3-4|6-7]_lcrit_alarm Output voltage critical low alarm
in[3-4|6-7]_min Minimum output voltage
in[3-4|6-7]_max_alarm Output voltage low alarm
in[3-4|6-7]_max Maximum output voltage
in[3-4|6-7]_max_alarm Output voltage high alarm
in[3-4|6-7]_crit Critical maximum output voltage
in[3-4|6-7]_crit_alarm Output voltage critical high alarm
power[1-2]_label "pout[1-2]"
power[1-2]_input Measured output power
temp1_input Measured temperature
temp1_crit Critical high temperature
temp1_crit_alarm Chip temperature critical high alarm
temp1_max Maximum temperature
temp1_max_alarm Chip temperature high alarm
====================== ====================================
Introduced by commit
3d6bcaa21fbd ("hwmon: (pmbus) Add support for Analog Devices LT7182S")
--
Cheers,
Stephen Rothwell
On Tue, Jun 07, 2022 at 02:19:58PM +1000, Stephen Rothwell wrote:
> Hi all,
>
> After merging the hwmon-staging tree, today's linux-next build (htmldocs)
> produced these warnings:
>
> Documentation/hwmon/lt7182s.rst:2: WARNING: Explicit markup ends without a blank line; unexpected unindent.
> Documentation/hwmon/lt7182s.rst:75: WARNING: Malformed table.
> Text in column margin in table line 33.
>
> ====================== ====================================
> curr[1-2]_label "iin[12]"
> curr[1-2]_input Measured input current
> curr[1-2]_max Maximum input current
> curr[1-2]_max_alarm Current high alarm
>
> curr[3-4]_label "iout[1-2]"
> curr[3-4]_input Measured output current
> curr[3-4]_highest Highest measured output current
> curr[3-4]_max Maximum output current
> curr[3-4]_max_alarm Output current high alarm
>
> in[1-2]_label "vin[12]"
> in[1-2]_input Measured input voltage
> in[1-2]_highest Highest measured input voltage
> in[1-2]_crit Critical maximum input voltage
> in[1-2]_crit_alarm Input voltage critical high alarm
> in[1-2]_min Minimum input voltage
> in[1-2]_min_alarm Input voltage low alarm
> in[1-2]_rated_min Rated minimum input voltage
> in[1-2]_rated_max Rated maximum input voltage
> in1_reset_history Write to reset history for all attributes
>
> in[3-5]_label "vmon[1-3]"
> in[3-5]_input Measured voltage on ITH1/ITH2/EXTVCC pins
> Only available if enabled with MFR_ADC_CONTROL_LT7182S
> command.
>
> in[3-4|6-7]_label "vout[1-2]"
> in[3-4|6-7]_input Measured output voltage
> in[3-4|6-7]_highest Highest measured output voltage
> in[3-4|6-7]_lcrit Critical minimum output voltage
> in[3-4|6-7]_lcrit_alarm Output voltage critical low alarm
> in[3-4|6-7]_min Minimum output voltage
> in[3-4|6-7]_max_alarm Output voltage low alarm
> in[3-4|6-7]_max Maximum output voltage
> in[3-4|6-7]_max_alarm Output voltage high alarm
> in[3-4|6-7]_crit Critical maximum output voltage
> in[3-4|6-7]_crit_alarm Output voltage critical high alarm
>
> power[1-2]_label "pout[1-2]"
> power[1-2]_input Measured output power
>
> temp1_input Measured temperature
> temp1_crit Critical high temperature
> temp1_crit_alarm Chip temperature critical high alarm
> temp1_max Maximum temperature
> temp1_max_alarm Chip temperature high alarm
> ====================== ====================================
>
> Introduced by commit
>
> 3d6bcaa21fbd ("hwmon: (pmbus) Add support for Analog Devices LT7182S")
>
Hi Stephen,
The warning above doesn't appear when doing htmldocs build using Sphinx
installed from pip on my system.
Cc-ing linux-doc list.
--
An old man doll... just what I always wanted! - Clara
On 6/7/22 02:37, Bagas Sanjaya wrote:
> On Tue, Jun 07, 2022 at 02:19:58PM +1000, Stephen Rothwell wrote:
>> Hi all,
>>
>> After merging the hwmon-staging tree, today's linux-next build (htmldocs)
>> produced these warnings:
>>
>> Documentation/hwmon/lt7182s.rst:2: WARNING: Explicit markup ends without a blank line; unexpected unindent.
>> Documentation/hwmon/lt7182s.rst:75: WARNING: Malformed table.
>> Text in column margin in table line 33.
>>
>> ====================== ====================================
>> curr[1-2]_label "iin[12]"
>> curr[1-2]_input Measured input current
>> curr[1-2]_max Maximum input current
>> curr[1-2]_max_alarm Current high alarm
>>
>> curr[3-4]_label "iout[1-2]"
>> curr[3-4]_input Measured output current
>> curr[3-4]_highest Highest measured output current
>> curr[3-4]_max Maximum output current
>> curr[3-4]_max_alarm Output current high alarm
>>
>> in[1-2]_label "vin[12]"
>> in[1-2]_input Measured input voltage
>> in[1-2]_highest Highest measured input voltage
>> in[1-2]_crit Critical maximum input voltage
>> in[1-2]_crit_alarm Input voltage critical high alarm
>> in[1-2]_min Minimum input voltage
>> in[1-2]_min_alarm Input voltage low alarm
>> in[1-2]_rated_min Rated minimum input voltage
>> in[1-2]_rated_max Rated maximum input voltage
>> in1_reset_history Write to reset history for all attributes
>>
>> in[3-5]_label "vmon[1-3]"
>> in[3-5]_input Measured voltage on ITH1/ITH2/EXTVCC pins
>> Only available if enabled with MFR_ADC_CONTROL_LT7182S
>> command.
>>
>> in[3-4|6-7]_label "vout[1-2]"
>> in[3-4|6-7]_input Measured output voltage
>> in[3-4|6-7]_highest Highest measured output voltage
>> in[3-4|6-7]_lcrit Critical minimum output voltage
>> in[3-4|6-7]_lcrit_alarm Output voltage critical low alarm
^
>> in[3-4|6-7]_min Minimum output voltage
>> in[3-4|6-7]_max_alarm Output voltage low alarm
>> in[3-4|6-7]_max Maximum output voltage
>> in[3-4|6-7]_max_alarm Output voltage high alarm
>> in[3-4|6-7]_crit Critical maximum output voltage
>> in[3-4|6-7]_crit_alarm Output voltage critical high alarm
>>
>> power[1-2]_label "pout[1-2]"
>> power[1-2]_input Measured output power
>>
>> temp1_input Measured temperature
>> temp1_crit Critical high temperature
>> temp1_crit_alarm Chip temperature critical high alarm
>> temp1_max Maximum temperature
>> temp1_max_alarm Chip temperature high alarm
>> ====================== ====================================
>>
>> Introduced by commit
>>
>> 3d6bcaa21fbd ("hwmon: (pmbus) Add support for Analog Devices LT7182S")
>>
>
> Hi Stephen,
>
> The warning above doesn't appear when doing htmldocs build using Sphinx
> installed from pip on my system.
>
I already fixed it up.
Guenter