From: Niravkumar L Rabara <[email protected]>
On architecture where reading the SRAM is slower than the pace at
controller fills it, with interrupt enabled while reading from
SRAM FIFO causes unwanted interrupt storm to CPU.
The inner "bytes to read" loop never exits and waits for the completion
so it is enough to only enable the watermark interrupt when we
are out of bytes to read, which only happens when we start the
transfer (waiting for the FIFO to fill up initially) if the SRAM
is slow.
So only using read watermark interrupt, as the current implementation
doesn't utilize the SRAM full and indirect complete read interrupt.
And disable all the read interrupts while reading from SRAM.
Signed-off-by: Niravkumar L Rabara <[email protected]>
---
drivers/spi/spi-cadence-quadspi.c | 32 ++++++++++++++++++++++++++++---
1 file changed, 29 insertions(+), 3 deletions(-)
diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
index 72b1a5a2298c..75a3cdb84fba 100644
--- a/drivers/spi/spi-cadence-quadspi.c
+++ b/drivers/spi/spi-cadence-quadspi.c
@@ -39,6 +39,7 @@
#define CQSPI_DISABLE_DAC_MODE BIT(1)
#define CQSPI_SUPPORT_EXTERNAL_DMA BIT(2)
#define CQSPI_NO_SUPPORT_WR_COMPLETION BIT(3)
+#define CQSPI_SLOW_SRAM BIT(4)
/* Capabilities */
#define CQSPI_SUPPORTS_OCTAL BIT(0)
@@ -87,6 +88,7 @@ struct cqspi_st {
bool use_dma_read;
u32 pd_dev_id;
bool wr_completion;
+ bool slow_sram;
};
struct cqspi_driver_platdata {
@@ -333,7 +335,10 @@ static irqreturn_t cqspi_irq_handler(int this_irq, void *dev)
}
}
- irq_status &= CQSPI_IRQ_MASK_RD | CQSPI_IRQ_MASK_WR;
+ else if (!cqspi->slow_sram)
+ irq_status &= CQSPI_IRQ_MASK_RD | CQSPI_IRQ_MASK_WR;
+ else
+ irq_status &= CQSPI_REG_IRQ_WATERMARK | CQSPI_IRQ_MASK_WR;
if (irq_status)
complete(&cqspi->transfer_complete);
@@ -673,7 +678,18 @@ static int cqspi_indirect_read_execute(struct cqspi_flash_pdata *f_pdata,
/* Clear all interrupts. */
writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
- writel(CQSPI_IRQ_MASK_RD, reg_base + CQSPI_REG_IRQMASK);
+ /*
+ * On SoCFPGA platform reading the SRAM is slow due to
+ * hardware limitation and causing read interrupt storm to CPU,
+ * so enabling only watermark interrupt to disable all read
+ * interrupts later as we want to run "bytes to read" loop with
+ * all the read interrupts disabled for max performance.
+ */
+
+ if (!cqspi->slow_sram)
+ writel(CQSPI_IRQ_MASK_RD, reg_base + CQSPI_REG_IRQMASK);
+ else
+ writel(CQSPI_REG_IRQ_WATERMARK, reg_base + CQSPI_REG_IRQMASK);
reinit_completion(&cqspi->transfer_complete);
writel(CQSPI_REG_INDIRECTRD_START_MASK,
@@ -684,6 +700,13 @@ static int cqspi_indirect_read_execute(struct cqspi_flash_pdata *f_pdata,
msecs_to_jiffies(CQSPI_READ_TIMEOUT_MS)))
ret = -ETIMEDOUT;
+ /*
+ * Disable all read interrupts until
+ * we are out of "bytes to read"
+ */
+ if (cqspi->slow_sram)
+ writel(0x0, reg_base + CQSPI_REG_IRQMASK);
+
bytes_to_read = cqspi_get_rd_sram_level(cqspi);
if (ret && bytes_to_read == 0) {
@@ -715,8 +738,11 @@ static int cqspi_indirect_read_execute(struct cqspi_flash_pdata *f_pdata,
bytes_to_read = cqspi_get_rd_sram_level(cqspi);
}
- if (remaining > 0)
+ if (remaining > 0) {
reinit_completion(&cqspi->transfer_complete);
+ if (cqspi->slow_sram)
+ writel(CQSPI_REG_IRQ_WATERMARK, reg_base + CQSPI_REG_IRQMASK);
+ }
}
/* Check indirect done status */
--
2.25.1