Changes from v1
---------------
v1: https://lore.kernel.org/all/[email protected]/
- fix node name DT schema problems
- removed "simple-bus" compatible from /clocks node
- use common "-clk" suffix for divclk1/4 node names
- use common "-regulator" suffix for wlan-en regulator node name
- move status properties last in all nodes
- fixed copyright to be assigned to myself, since I don't work for LF
- add Krzysztof's Rb tag to bindings patch
This patch series adds support for the OnePlus 3 and OnePlus 3T mobile
phones based on the Qualcomm MSM8996 SoC. Currently includes support for
the following:
- UART console via PCB test pads
- Qualcomm Atheros QCA6174 WiFi and Bluetooth
- NXP TFA9890 Speaker Amplifier
- TI BQ27541 Battery Fuel Gauge
- Synaptics RMI4 Touchscreen
- UFS Storage
Harry Austen (4):
arm64: dts: qcom: msm8996: standardize blsp indexing
arm64: boot: dts: msm8996: add blsp1_i2c6 node
dt-bindings: arm: qcom: add oneplus3(t) devices
arm64: dts: qcom: msm8996: add support for oneplus3(t)
.../devicetree/bindings/arm/qcom.yaml | 2 +
arch/arm64/boot/dts/qcom/Makefile | 2 +
.../boot/dts/qcom/msm8996-oneplus-common.dtsi | 787 ++++++++++++++++++
arch/arm64/boot/dts/qcom/msm8996-oneplus3.dts | 44 +
.../arm64/boot/dts/qcom/msm8996-oneplus3t.dts | 45 +
arch/arm64/boot/dts/qcom/msm8996.dtsi | 49 +-
6 files changed, 920 insertions(+), 9 deletions(-)
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-oneplus-common.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-oneplus3.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-oneplus3t.dts
--
2.38.1
Use one-based indexing throughout the file for BLSP devices to avoid
confusion. Most of the node names and labels are consistent already.
This patch just fixes a few pinconf node names to match the one-based
indexing used in the label names.
Signed-off-by: Harry Austen <[email protected]>
---
v1 -> v2: no changes
arch/arm64/boot/dts/qcom/msm8996.dtsi | 18 +++++++++---------
1 file changed, 9 insertions(+), 9 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 5ff8de3e3de7..39afd8a99488 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -1304,14 +1304,14 @@ blsp1_spi1_sleep: blsp1-spi1-sleep {
bias-pull-down;
};
- blsp2_uart2_2pins_default: blsp2-uart1-2pins {
+ blsp2_uart2_2pins_default: blsp2-uart2-2pins {
pins = "gpio4", "gpio5";
function = "blsp_uart8";
drive-strength = <16>;
bias-disable;
};
- blsp2_uart2_2pins_sleep: blsp2-uart1-2pins-sleep {
+ blsp2_uart2_2pins_sleep: blsp2-uart2-2pins-sleep {
pins = "gpio4", "gpio5";
function = "gpio";
drive-strength = <2>;
@@ -1478,28 +1478,28 @@ blsp1_uart2_sleep: blsp1-uart2-sleep {
bias-disable;
};
- blsp1_i2c3_default: blsp1-i2c2-default {
+ blsp1_i2c3_default: blsp1-i2c3-default {
pins = "gpio47", "gpio48";
function = "blsp_i2c3";
drive-strength = <16>;
bias-disable;
};
- blsp1_i2c3_sleep: blsp1-i2c2-sleep {
+ blsp1_i2c3_sleep: blsp1-i2c3-sleep {
pins = "gpio47", "gpio48";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
- blsp2_uart3_4pins_default: blsp2-uart2-4pins {
+ blsp2_uart3_4pins_default: blsp2-uart3-4pins {
pins = "gpio49", "gpio50", "gpio51", "gpio52";
function = "blsp_uart9";
drive-strength = <16>;
bias-disable;
};
- blsp2_uart3_4pins_sleep: blsp2-uart2-4pins-sleep {
+ blsp2_uart3_4pins_sleep: blsp2-uart3-4pins-sleep {
pins = "gpio49", "gpio50", "gpio51", "gpio52";
function = "blsp_uart9";
drive-strength = <2>;
@@ -1535,7 +1535,7 @@ blsp2_i2c1_default: blsp2-i2c1 {
bias-disable;
};
- blsp2_i2c1_sleep: blsp2-i2c0-sleep {
+ blsp2_i2c1_sleep: blsp2-i2c1-sleep {
pins = "gpio55", "gpio56";
function = "gpio";
drive-strength = <2>;
@@ -1567,7 +1567,7 @@ cdc_reset_sleep: cdc-reset-sleep {
output-low;
};
- blsp2_spi6_default: blsp2-spi5-default {
+ blsp2_spi6_default: blsp2-spi6-default {
spi {
pins = "gpio85", "gpio86", "gpio88";
function = "blsp_spi12";
@@ -1584,7 +1584,7 @@ cs {
};
};
- blsp2_spi6_sleep: blsp2-spi5-sleep {
+ blsp2_spi6_sleep: blsp2-spi6-sleep {
pins = "gpio85", "gpio86", "gpio87", "gpio88";
function = "gpio";
drive-strength = <2>;
--
2.38.1
Add compatible strings for the OnePlus 3 and 3T phones which utilise the
Qualcomm MSM8996 SoC.
Signed-off-by: Harry Austen <[email protected]>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
---
v1 -> v2: add Krzysztof's Rb tag
Documentation/devicetree/bindings/arm/qcom.yaml | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 207e28260206..aa441918f314 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -222,6 +222,8 @@ properties:
- items:
- enum:
+ - oneplus,oneplus3
+ - oneplus,oneplus3t
- qcom,msm8996-mtp
- sony,dora-row
- sony,kagura-row
--
2.38.1
Add initial support for OnePlus 3 and 3T mobile phones. They are based
on the MSM8996 SoC.
Co-developed-by: Yassine Oudjana <[email protected]>
Signed-off-by: Yassine Oudjana <[email protected]>
Signed-off-by: Harry Austen <[email protected]>
---
v1 -> v2: address Krzysztof's review comments
arch/arm64/boot/dts/qcom/Makefile | 2 +
.../boot/dts/qcom/msm8996-oneplus-common.dtsi | 787 ++++++++++++++++++
arch/arm64/boot/dts/qcom/msm8996-oneplus3.dts | 44 +
.../arm64/boot/dts/qcom/msm8996-oneplus3t.dts | 45 +
4 files changed, 878 insertions(+)
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-oneplus-common.dtsi
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-oneplus3.dts
create mode 100644 arch/arm64/boot/dts/qcom/msm8996-oneplus3t.dts
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index b0558d3389e5..bc0d93a0dad3 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -33,6 +33,8 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-satsuki.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-sumire.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8994-sony-xperia-kitakami-suzuran.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8996-oneplus3.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8996-oneplus3t.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-sony-xperia-tone-dora.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-sony-xperia-tone-kagura.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8996-sony-xperia-tone-keyaki.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8996-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/msm8996-oneplus-common.dtsi
new file mode 100644
index 000000000000..20f5c103c63b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-oneplus-common.dtsi
@@ -0,0 +1,787 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2022, Harry Austen <[email protected]>
+ */
+
+#include "msm8996.dtsi"
+#include "pm8994.dtsi"
+#include "pmi8994.dtsi"
+#include "pmi8996.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+#include <dt-bindings/sound/qcom,wcd9335.h>
+
+/ {
+ aliases {
+ serial0 = &blsp1_uart2;
+ serial1 = &blsp2_uart2;
+ };
+
+ battery: battery {
+ compatible = "simple-battery";
+
+ constant-charge-current-max-microamp = <3000000>;
+ voltage-min-design-microvolt = <3400000>;
+ };
+
+ chosen {
+ stdout-path = "serial1:115200n8";
+ };
+
+ clocks {
+ div1_mclk: div1-clk {
+ compatible = "gpio-gate-clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&audio_mclk>;
+ #clock-cells = <0>;
+ clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
+ enable-gpios = <&pm8994_gpios 15 GPIO_ACTIVE_HIGH>;
+ };
+
+ divclk4: div4-clk {
+ compatible = "fixed-clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&divclk4_pin_a>;
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "divclk4";
+ };
+ };
+
+ reserved-memory {
+ ramoops@ac000000 {
+ compatible = "ramoops";
+ reg = <0 0xac000000 0 0x200000>;
+ record-size = <0x20000>;
+ console-size = <0x100000>;
+ pmsg-size = <0x80000>;
+ };
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ wlan_en: wlan-en-regulator {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wlan_en_gpios>;
+ regulator-name = "wlan-en-regulator";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&pm8994_gpios 8 GPIO_ACTIVE_HIGH>;
+
+ /* WLAN card specific delay */
+ startup-delay-us = <70000>;
+ enable-active-high;
+ };
+};
+
+&adsp_pil {
+ status = "okay";
+};
+
+&blsp1_i2c3 {
+ status = "okay";
+
+ tfa9890_amp: audio-codec@36 {
+ compatible = "nxp,tfa9890";
+ reg = <0x36>;
+ #sound-dai-cells = <0>;
+ };
+};
+
+&blsp1_i2c6 {
+ status = "okay";
+
+ bq27541: fuel-gauge@55 {
+ compatible = "ti,bq27541";
+ reg = <0x55>;
+ };
+};
+
+&blsp1_uart2 {
+ label = "BT-UART";
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,qca6174-bt";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_en_gpios>;
+ enable-gpios = <&pm8994_gpios 19 GPIO_ACTIVE_HIGH>;
+ clocks = <&divclk4>;
+ };
+};
+
+&blsp2_i2c1 {
+ status = "okay";
+};
+
+&blsp2_i2c6 {
+ status = "okay";
+
+ synaptics_rmi4_i2c: touchscreen@20 {
+ compatible = "syna,rmi4-i2c";
+ reg = <0x20>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&touch_default>;
+ pinctrl-1 = <&touch_suspend>;
+ vdd-supply = <&vreg_l22a_3p0>;
+ vio-supply = <&vreg_s4a_1p8>;
+ syna,reset-delay-ms = <200>;
+ syna,startup-delay-ms = <200>;
+
+ rmi4-f01@1 {
+ reg = <0x1>;
+ syna,nosleep-mode = <1>;
+ };
+
+ rmi4-f12@12 {
+ reg = <0x12>;
+ syna,sensor-type = <1>;
+ touchscreen-x-mm = <68>;
+ touchscreen-y-mm = <122>;
+ };
+ };
+};
+
+&blsp2_uart2 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp2_uart2_2pins_default>;
+ pinctrl-1 = <&blsp2_uart2_2pins_sleep>;
+ status = "okay";
+};
+
+&camss {
+ vdda-supply = <&vreg_l2a_1p25>;
+};
+
+&dsi0 {
+ vdda-supply = <&vreg_l2a_1p25>;
+ vcca-supply = <&vreg_l22a_3p0>;
+ status = "okay";
+};
+
+&dsi0_out {
+ data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+ vdda-supply = <&vreg_l2a_1p25>;
+ vcca-supply = <&vreg_l28a_0p925>;
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+};
+
+&hsusb_phy1 {
+ vdd-supply = <&vreg_l28a_0p925>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+ status = "okay";
+};
+
+&hsusb_phy2 {
+ vdd-supply = <&vreg_l28a_0p925>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+ status = "okay";
+};
+
+&mdp {
+ status = "okay";
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mmcc {
+ vdd-gfx-supply = <&vdd_gfx>;
+};
+
+&mss_pil {
+ pll-supply = <&vreg_l12a_1p8>;
+ status = "okay";
+};
+
+&pcie0 {
+ perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+ vddpe-3v3-supply = <&wlan_en>;
+ vdda-supply = <&vreg_l28a_0p925>;
+ status = "okay";
+};
+
+&pcie_phy {
+ vdda-phy-supply = <&vreg_l28a_0p925>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ status = "okay";
+};
+
+&pm8994_gpios {
+ bt_en_gpios: bt-en-gpios-state {
+ pins = "gpio19";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ output-low;
+ power-source = <PM8994_GPIO_S4>;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ bias-pull-down;
+ };
+
+ wlan_en_gpios: wlan-en-gpios-state {
+ pins = "gpio8";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ output-low;
+ power-source = <PM8994_GPIO_S4>;
+ qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+ bias-pull-down;
+ };
+
+ audio_mclk: divclk1-state {
+ pins = "gpio15";
+ function = PMIC_GPIO_FUNC_FUNC1;
+ power-source = <PM8994_GPIO_S4>;
+ };
+
+ divclk4_pin_a: divclk4-state {
+ pins = "gpio18";
+ function = PMIC_GPIO_FUNC_FUNC2;
+ bias-disable;
+ power-source = <PM8994_GPIO_S4>;
+ };
+};
+
+&pm8994_spmi_regulators {
+ qcom,saw-reg = <&saw3>;
+
+ s9 {
+ qcom,saw-slave;
+ };
+
+ s10 {
+ qcom,saw-slave;
+ };
+
+ s11 {
+ qcom,saw-leader;
+ regulator-min-microvolt = <1140000>;
+ regulator-max-microvolt = <1140000>;
+ regulator-max-step-microvolt = <150000>;
+ regulator-always-on;
+ };
+};
+
+&pmi8994_spmi_regulators {
+ vdd_gfx: s2 {
+ regulator-name = "vdd-gfx";
+ regulator-min-microvolt = <980000>;
+ regulator-max-microvolt = <1230000>;
+ };
+};
+
+&q6asmdai {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ dai@0 {
+ reg = <0>;
+ };
+
+ dai@1 {
+ reg = <1>;
+ };
+
+ dai@2 {
+ reg = <2>;
+ };
+};
+
+&rpm_requests {
+ regulators {
+ compatible = "qcom,rpm-pm8994-regulators";
+
+ vreg_s3a_1p3: s3 {
+ regulator-name = "vreg_s3a_1p3";
+ regulator-min-microvolt = <1300000>;
+ regulator-max-microvolt = <1300000>;
+ };
+
+ vreg_s4a_1p8: s4 {
+ regulator-name = "vreg_s4a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vreg_s5a_2p15: s5 {
+ regulator-name = "vreg_s5a_2p15";
+ regulator-min-microvolt = <2150000>;
+ regulator-max-microvolt = <2150000>;
+ };
+
+ vreg_s7a_0p8: s7 {
+ regulator-name = "vreg_s7a_0p8";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ };
+
+ vreg_l1a_1p0: l1 {
+ regulator-name = "vreg_l1a_1p0";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ vreg_l2a_1p25: l2 {
+ regulator-name = "vreg_l2a_1p25";
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l3a_1p1: l3 {
+ regulator-name = "vreg_l3a_1p1";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ };
+
+ vreg_l4a_1p225: l4 {
+ regulator-name = "vreg_l4a_1p225";
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ };
+
+ vreg_l6a_1p2: l6 {
+ regulator-name = "vreg_l6a_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vreg_l7a_1p8: l7 {
+ regulator-name = "vreg_l7a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_l9a_1p8: l9 {
+ regulator-name = "vreg_l9a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_l10a_1p8: l10 {
+ regulator-name = "vreg_l10a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_l11a_1p15: l11 {
+ regulator-name = "vreg_l11a_1p15";
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+ };
+
+ vreg_l12a_1p8: l12 {
+ regulator-name = "vreg_l12a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l13a_2p95: l13 {
+ regulator-name = "vreg_l13a_2p95";
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ vreg_l16a_2p7: l16 {
+ regulator-name = "vreg_l16a_2p7";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ vreg_l17a_2p6: l17 {
+ regulator-name = "vreg_l17a_2p6";
+ regulator-min-microvolt = <2600000>;
+ regulator-max-microvolt = <2600000>;
+ };
+
+ vreg_l18a_3p3: l18 {
+ regulator-name = "vreg_l18a_3p3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vreg_l19a_3p0: l19 {
+ regulator-name = "vreg_l19a_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ vreg_l20a_2p95: l20 {
+ regulator-name = "vreg_l20a_2p95";
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l21a_2p95: l21 {
+ regulator-name = "vreg_l21a_2p95";
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-allow-set-load;
+ regulator-system-load = <200000>;
+ };
+
+ vreg_l22a_3p0: l22 {
+ regulator-name = "vreg_l22a_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vreg_l23a_2p8: l23 {
+ regulator-name = "vreg_l23a_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ vreg_l24a_3p075: l24 {
+ regulator-name = "vreg_l24a_3p075";
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+
+ vreg_l25a_1p2: l25 {
+ regulator-name = "vreg_l25a_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-allow-set-load;
+ regulator-always-on;
+ };
+
+ vreg_l27a_1p2: l27 {
+ regulator-name = "vreg_l27a_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vreg_l28a_0p925: l28 {
+ regulator-name = "vreg_l28a_0p925";
+ regulator-min-microvolt = <925000>;
+ regulator-max-microvolt = <925000>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l29a_2p8: l29 {
+ regulator-name = "vreg_l29a_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ vreg_l30a_1p8: l30 {
+ regulator-name = "vreg_l30a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_l32a_1p8: l32 {
+ regulator-name = "vreg_l32a_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+};
+
+&slpi_pil {
+ status = "okay";
+};
+
+&sound {
+ compatible = "qcom,apq8096-sndcard";
+ model = "OnePlus3";
+ audio-routing = "RX_BIAS", "MCLK",
+ "AMIC2", "MIC BIAS2",
+ "MIC BIAS2", "Headset Mic",
+ "AMIC4", "MIC BIAS1",
+ "MIC BIAS1", "Primary Mic",
+ "AMIC5", "MIC BIAS3",
+ "MIC BIAS3", "Noise Mic";
+
+ mm1-dai-link {
+ link-name = "MultiMedia1";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
+ };
+ };
+
+ mm2-dai-link {
+ link-name = "MultiMedia2";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
+ };
+ };
+
+ mm3-dai-link {
+ link-name = "MultiMedia3";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
+ };
+ };
+
+ mm4-dai-link {
+ link-name = "MultiMedia4";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA4>;
+ };
+ };
+
+ mm5-dai-link {
+ link-name = "MultiMedia5";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA5>;
+ };
+ };
+
+ mm6-dai-link {
+ link-name = "MultiMedia6";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA6>;
+ };
+ };
+
+ mm7-dai-link {
+ link-name = "MultiMedia7";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA7>;
+ };
+ };
+
+ mm8-dai-link {
+ link-name = "MultiMedia8";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA8>;
+ };
+ };
+
+ mm9-dai-link {
+ link-name = "MultiMedia9";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA9>;
+ };
+ };
+
+ mm10-dai-link {
+ link-name = "MultiMedia10";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA10>;
+ };
+ };
+
+ mm11-dai-link {
+ link-name = "MultiMedia11";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA11>;
+ };
+ };
+
+ mm12-dai-link {
+ link-name = "MultiMedia12";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA12>;
+ };
+ };
+
+ mm13-dai-link {
+ link-name = "MultiMedia13";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA13>;
+ };
+ };
+
+ mm14-dai-link {
+ link-name = "MultiMedia14";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA14>;
+ };
+ };
+
+ mm15-dai-link {
+ link-name = "MultiMedia15";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA15>;
+ };
+ };
+
+ mm16-dai-link {
+ link-name = "MultiMedia16";
+
+ cpu {
+ sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA16>;
+ };
+ };
+
+ slim-dai-link {
+ link-name = "SLIM Playback";
+
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_6_RX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&wcd9335 AIF4_PB>;
+ };
+ };
+
+ slimcap-dai-link {
+ link-name = "SLIM Capture";
+
+ cpu {
+ sound-dai = <&q6afedai SLIMBUS_0_TX>;
+ };
+
+ platform {
+ sound-dai = <&q6routing>;
+ };
+
+ codec {
+ sound-dai = <&wcd9335 AIF1_CAP>;
+ };
+ };
+
+ speaker-dai-link {
+ link-name = "Speaker";
+
+ cpu {
+ sound-dai = <&q6afedai QUATERNARY_MI2S_RX>;
+ };
+
+ codec {
+ sound-dai = <&tfa9890_amp>;
+ };
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <81 4>;
+
+ mdss_dsi_active: mdss-dsi-active-state {
+ pins = "gpio8";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ mdss_dsi_suspend: mdss-dsi-suspend-state {
+ pins = "gpio8";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ mdss_te_active: mdss-te-active-state {
+ pins = "gpio10";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ mdss_te_suspend: mdss-te-suspend-state {
+ pins = "gpio10";
+ function = "mdp_vsync";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ touch_default: touch-default-state {
+ pins = "gpio89", "gpio125", "gpio49";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ touch_suspend: touch-suspend-state {
+ pins = "gpio89", "gpio125", "gpio49";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+};
+
+&ufsphy {
+ vdda-phy-supply = <&vreg_l28a_0p925>;
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vddp-ref-clk-supply = <&vreg_l25a_1p2>;
+
+ status = "okay";
+};
+
+&ufshc {
+ vcc-supply = <&vreg_l20a_2p95>;
+ vccq-supply = <&vreg_l25a_1p2>;
+ vccq2-supply = <&vreg_s4a_1p8>;
+
+ vcc-max-microamp = <600000>;
+ vccq-max-microamp = <450000>;
+ vccq2-max-microamp = <450000>;
+
+ status = "okay";
+};
+
+&usb3 {
+ status = "okay";
+};
+
+&usb3_dwc3 {
+ phys = <&hsusb_phy1>;
+ phy-names = "usb2-phy";
+
+ maximum-speed = "high-speed";
+};
+
+&venus {
+ status = "okay";
+};
+
+&wcd9335 {
+ clock-names = "mclk", "slimbus";
+ clocks = <&div1_mclk>,
+ <&rpmcc RPM_SMD_BB_CLK1>;
+
+ vdd-buck-supply = <&vreg_s4a_1p8>;
+ vdd-buck-sido-supply = <&vreg_s4a_1p8>;
+ vdd-tx-supply = <&vreg_s4a_1p8>;
+ vdd-rx-supply = <&vreg_s4a_1p8>;
+ vdd-io-supply = <&vreg_s4a_1p8>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-oneplus3.dts b/arch/arm64/boot/dts/qcom/msm8996-oneplus3.dts
new file mode 100644
index 000000000000..1bdc1b134305
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-oneplus3.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2022, Harry Austen <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "msm8996-oneplus-common.dtsi"
+
+/ {
+ model = "OnePlus 3";
+ compatible = "oneplus,oneplus3", "qcom,msm8996";
+ chassis-type = "handset";
+ qcom,board-id = <8 0 15801 15>, <8 0 15801 16>;
+ qcom,msm-id = <246 0x30001>;
+};
+
+&adsp_pil {
+ firmware-name = "qcom/msm8996/oneplus3/adsp.mbn";
+};
+
+&battery {
+ charge-full-design-microamp-hours = <3000000>;
+ voltage-max-design-microvolt = <4350000>;
+};
+
+&gpu {
+ zap-shader {
+ firmware-name = "qcom/msm8996/oneplus3/a530_zap.mbn";
+ };
+};
+
+&mss_pil {
+ firmware-name = "qcom/msm8996/oneplus3/mba.mbn",
+ "qcom/msm8996/oneplus3/modem.mbn";
+};
+
+&slpi_pil {
+ firmware-name = "qcom/msm8996/oneplus3/slpi.mbn";
+};
+
+&venus {
+ firmware-name = "qcom/msm8996/oneplus3/venus.mbn";
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-oneplus3t.dts b/arch/arm64/boot/dts/qcom/msm8996-oneplus3t.dts
new file mode 100644
index 000000000000..34f837dd0c12
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-oneplus3t.dts
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2022, Harry Austen <[email protected]>
+ */
+
+/dts-v1/;
+
+#include "msm8996-oneplus-common.dtsi"
+
+/ {
+ model = "OnePlus 3T";
+ compatible = "oneplus,oneplus3t", "qcom,msm8996";
+ chassis-type = "handset";
+ qcom,board-id = <8 0 15811 26>,
+ <8 0 15811 27>,
+ <8 0 15811 28>;
+};
+
+&adsp_pil {
+ firmware-name = "qcom/msm8996/oneplus3t/adsp.mbn";
+};
+
+&battery {
+ charge-full-design-microamp-hours = <3400000>;
+ voltage-max-design-microvolt = <4400000>;
+};
+
+&gpu {
+ zap-shader {
+ firmware-name = "qcom/msm8996/oneplus3t/a530_zap.mbn";
+ };
+};
+
+&mss_pil {
+ firmware-name = "qcom/msm8996/oneplus3t/mba.mbn",
+ "qcom/msm8996/oneplus3t/modem.mbn";
+};
+
+&slpi_pil {
+ firmware-name = "qcom/msm8996/oneplus3t/slpi.mbn";
+};
+
+&venus {
+ firmware-name = "qcom/msm8996/oneplus3t/venus.mbn";
+};
--
2.38.1
Add support for the sixth I2C interface on the MSM8996 SoC.
Signed-off-by: Harry Austen <[email protected]>
---
v1 -> v2: use hyphens and add "-state" pinctrl node name suffix
arch/arm64/boot/dts/qcom/msm8996.dtsi | 31 +++++++++++++++++++++++++++
1 file changed, 31 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 39afd8a99488..bb49496a5413 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -1418,6 +1418,20 @@ pwdn {
};
};
+ blsp1_i2c6_default: blsp1-i2c6-state {
+ pins = "gpio27", "gpio28";
+ function = "blsp_i2c6";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ blsp1_i2c6_sleep: blsp1-i2c6-sleep-state {
+ pins = "gpio27", "gpio28";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
pcie0_state_on: pcie0-state-on {
perst {
pins = "gpio35";
@@ -3141,6 +3155,23 @@ blsp1_i2c3: i2c@7577000 {
status = "disabled";
};
+ blsp1_i2c6: i2c@757a000 {
+ compatible = "qcom,i2c-qup-v2.2.1";
+ reg = <0x757a000 0x1000>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+ <&gcc GCC_BLSP1_AHB_CLK>;
+ clock-names = "core", "iface";
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&blsp1_i2c6_default>;
+ pinctrl-1 = <&blsp1_i2c6_sleep>;
+ dmas = <&blsp1_dma 22>, <&blsp1_dma 23>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
blsp2_dma: dma-controller@7584000 {
compatible = "qcom,bam-v1.7.0";
reg = <0x07584000 0x2b000>;
--
2.38.1
On 23/10/2022 16:45, Harry Austen wrote:
> Add support for the sixth I2C interface on the MSM8996 SoC.
>
> Signed-off-by: Harry Austen <[email protected]>
> ---
> v1 -> v2: use hyphens and add "-state" pinctrl node name suffix
>
Reviewed-by: Krzysztof Kozlowski <[email protected]>
Best regards,
Krzysztof
On Sun, 23 Oct 2022 20:45:16 +0000, Harry Austen wrote:
> Changes from v1
> ---------------
> v1: https://lore.kernel.org/all/[email protected]/
> - fix node name DT schema problems
> - removed "simple-bus" compatible from /clocks node
> - use common "-clk" suffix for divclk1/4 node names
> - use common "-regulator" suffix for wlan-en regulator node name
> - move status properties last in all nodes
> - fixed copyright to be assigned to myself, since I don't work for LF
> - add Krzysztof's Rb tag to bindings patch
>
> [...]
Applied, thanks!
[1/4] arm64: dts: qcom: msm8996: standardize blsp indexing
commit: 1a94ba5b44c5448c7ec962a5ce66eb12a6042288
[2/4] arm64: boot: dts: msm8996: add blsp1_i2c6 node
commit: 18c32de673bf3ade651979be48e9a14bfe612487
[3/4] dt-bindings: arm: qcom: add oneplus3(t) devices
commit: ce5d6ba21ae6c83fc2db385f9202272ca0d403f2
[4/4] arm64: dts: qcom: msm8996: add support for oneplus3(t)
commit: 5a134c940cd368b72d5bcf24132b8f951be9a4c1
Best regards,
--
Bjorn Andersson <[email protected]>