Reorganize macro definitions into sections for each supported
device, with additional comments on their purpose. This should
make it easier to follow what report each offset is coming
from. Also, reformat per-device initializations in
aqc_probe() to organize them into sections (fan info,
temp sensors, other parameters and lastly labels).
No functional changes.
Signed-off-by: Aleksa Savic <[email protected]>
---
drivers/hwmon/aquacomputer_d5next.c | 97 +++++++++++++++++++----------
1 file changed, 63 insertions(+), 34 deletions(-)
diff --git a/drivers/hwmon/aquacomputer_d5next.c b/drivers/hwmon/aquacomputer_d5next.c
index 608f57f59cf9..49d3f9876fe8 100644
--- a/drivers/hwmon/aquacomputer_d5next.c
+++ b/drivers/hwmon/aquacomputer_d5next.c
@@ -59,7 +59,7 @@ static u8 secondary_ctrl_report[] = {
0x02, 0x00, 0x00, 0x00, 0x02, 0x00, 0x00, 0x00, 0x00, 0x34, 0xC6
};
-/* Register offsets for all Aquacomputer devices */
+/* Sensor sizes and offsets for all Aquacomputer devices */
#define AQC_TEMP_SENSOR_SIZE 0x02
#define AQC_TEMP_SENSOR_DISCONNECTED 0x7FFF
#define AQC_FAN_PERCENT_OFFSET 0x00
@@ -68,67 +68,80 @@ static u8 secondary_ctrl_report[] = {
#define AQC_FAN_POWER_OFFSET 0x06
#define AQC_FAN_SPEED_OFFSET 0x08
-/* Register offsets for the D5 Next pump */
-#define D5NEXT_POWER_CYCLES 0x18
-#define D5NEXT_COOLANT_TEMP 0x57
+/* Specs of the D5 Next pump */
#define D5NEXT_NUM_FANS 2
#define D5NEXT_NUM_SENSORS 1
#define D5NEXT_NUM_VIRTUAL_SENSORS 8
-#define D5NEXT_VIRTUAL_SENSORS_START 0x3f
+#define D5NEXT_CTRL_REPORT_SIZE 0x329
+
+/* Sensor report offsets for the D5 Next pump */
+#define D5NEXT_POWER_CYCLES 0x18
+#define D5NEXT_COOLANT_TEMP 0x57
#define D5NEXT_PUMP_OFFSET 0x6c
#define D5NEXT_FAN_OFFSET 0x5f
#define D5NEXT_5V_VOLTAGE 0x39
#define D5NEXT_12V_VOLTAGE 0x37
-#define D5NEXT_CTRL_REPORT_SIZE 0x329
-#define D5NEXT_TEMP_CTRL_OFFSET 0x2D
+#define D5NEXT_VIRTUAL_SENSORS_START 0x3f
static u8 d5next_sensor_fan_offsets[] = { D5NEXT_PUMP_OFFSET, D5NEXT_FAN_OFFSET };
-/* Pump and fan speed registers in D5 Next control report (from 0-100%) */
-static u16 d5next_ctrl_fan_offsets[] = { 0x97, 0x42 };
+/* Control report offsets for the D5 Next pump */
+#define D5NEXT_TEMP_CTRL_OFFSET 0x2D /* Temperature sensor offsets location */
+static u16 d5next_ctrl_fan_offsets[] = { 0x97, 0x42 }; /* Pump and fan speed (from 0-100%) */
-/* Register offsets for the Farbwerk RGB controller */
+/* Spec and sensor report offset for the Farbwerk RGB controller */
#define FARBWERK_NUM_SENSORS 4
#define FARBWERK_SENSOR_START 0x2f
-/* Register offsets for the Farbwerk 360 RGB controller */
+/* Specs of the Farbwerk 360 RGB controller */
#define FARBWERK360_NUM_SENSORS 4
-#define FARBWERK360_SENSOR_START 0x32
#define FARBWERK360_NUM_VIRTUAL_SENSORS 16
-#define FARBWERK360_VIRTUAL_SENSORS_START 0x3a
#define FARBWERK360_CTRL_REPORT_SIZE 0x682
+
+/* Sensor report offsets for the Farbwerk 360 */
+#define FARBWERK360_SENSOR_START 0x32
+#define FARBWERK360_VIRTUAL_SENSORS_START 0x3a
+
+/* Control report offsets for the Farbwerk 360 */
#define FARBWERK360_TEMP_CTRL_OFFSET 0x8
-/* Register offsets for the Octo fan controller */
-#define OCTO_POWER_CYCLES 0x18
+/* Specs of the Octo fan controller */
#define OCTO_NUM_FANS 8
#define OCTO_NUM_SENSORS 4
-#define OCTO_SENSOR_START 0x3D
#define OCTO_NUM_VIRTUAL_SENSORS 16
-#define OCTO_VIRTUAL_SENSORS_START 0x45
#define OCTO_CTRL_REPORT_SIZE 0x65F
-#define OCTO_TEMP_CTRL_OFFSET 0xA
+
+/* Sensor report offsets for the Octo */
+#define OCTO_POWER_CYCLES 0x18
+#define OCTO_SENSOR_START 0x3D
+#define OCTO_VIRTUAL_SENSORS_START 0x45
static u8 octo_sensor_fan_offsets[] = { 0x7D, 0x8A, 0x97, 0xA4, 0xB1, 0xBE, 0xCB, 0xD8 };
-/* Fan speed registers in Octo control report (from 0-100%) */
+/* Control report offsets for the Octo */
+#define OCTO_TEMP_CTRL_OFFSET 0xA
+/* Fan speed offsets (0-100%) */
static u16 octo_ctrl_fan_offsets[] = { 0x5B, 0xB0, 0x105, 0x15A, 0x1AF, 0x204, 0x259, 0x2AE };
-/* Register offsets for the Quadro fan controller */
-#define QUADRO_POWER_CYCLES 0x18
+/* Specs of Quadro fan controller */
#define QUADRO_NUM_FANS 4
#define QUADRO_NUM_SENSORS 4
-#define QUADRO_SENSOR_START 0x34
#define QUADRO_NUM_VIRTUAL_SENSORS 16
-#define QUADRO_VIRTUAL_SENSORS_START 0x3c
#define QUADRO_CTRL_REPORT_SIZE 0x3c1
+
+/* Sensor report offsets for the Quadro */
+#define QUADRO_POWER_CYCLES 0x18
+#define QUADRO_SENSOR_START 0x34
+#define QUADRO_VIRTUAL_SENSORS_START 0x3c
#define QUADRO_FLOW_SENSOR_OFFSET 0x6e
-#define QUADRO_TEMP_CTRL_OFFSET 0xA
static u8 quadro_sensor_fan_offsets[] = { 0x70, 0x7D, 0x8A, 0x97 };
-/* Fan speed registers in Quadro control report (from 0-100%) */
-static u16 quadro_ctrl_fan_offsets[] = { 0x37, 0x8c, 0xe1, 0x136 };
+/* Control report offsets for the Quadro */
+#define QUADRO_TEMP_CTRL_OFFSET 0xA
+static u16 quadro_ctrl_fan_offsets[] = { 0x37, 0x8c, 0xe1, 0x136 }; /* Fan speed offsets (0-100%) */
-/* Register offsets for the High Flow Next */
+/* Specs of High Flow Next flow sensor */
#define HIGHFLOWNEXT_NUM_SENSORS 2
+
+/* Sensor report offsets for the High Flow Next */
#define HIGHFLOWNEXT_SENSOR_START 85
#define HIGHFLOWNEXT_FLOW 81
#define HIGHFLOWNEXT_WATER_QUALITY 89
@@ -903,14 +916,17 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
priv->num_fans = D5NEXT_NUM_FANS;
priv->fan_sensor_offsets = d5next_sensor_fan_offsets;
priv->fan_ctrl_offsets = d5next_ctrl_fan_offsets;
+
priv->num_temp_sensors = D5NEXT_NUM_SENSORS;
priv->temp_sensor_start_offset = D5NEXT_COOLANT_TEMP;
priv->num_virtual_temp_sensors = D5NEXT_NUM_VIRTUAL_SENSORS;
priv->virtual_temp_sensor_start_offset = D5NEXT_VIRTUAL_SENSORS_START;
- priv->power_cycle_count_offset = D5NEXT_POWER_CYCLES;
- priv->buffer_size = D5NEXT_CTRL_REPORT_SIZE;
priv->temp_ctrl_offset = D5NEXT_TEMP_CTRL_OFFSET;
+ priv->buffer_size = D5NEXT_CTRL_REPORT_SIZE;
+
+ priv->power_cycle_count_offset = D5NEXT_POWER_CYCLES;
+
priv->temp_label = label_d5next_temp;
priv->virtual_temp_label = label_virtual_temp_sensors;
priv->speed_label = label_d5next_speeds;
@@ -922,20 +938,25 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
priv->kind = farbwerk;
priv->num_fans = 0;
+
priv->num_temp_sensors = FARBWERK_NUM_SENSORS;
priv->temp_sensor_start_offset = FARBWERK_SENSOR_START;
+
priv->temp_label = label_temp_sensors;
break;
case USB_PRODUCT_ID_FARBWERK360:
priv->kind = farbwerk360;
priv->num_fans = 0;
+
priv->num_temp_sensors = FARBWERK360_NUM_SENSORS;
priv->temp_sensor_start_offset = FARBWERK360_SENSOR_START;
priv->num_virtual_temp_sensors = FARBWERK360_NUM_VIRTUAL_SENSORS;
priv->virtual_temp_sensor_start_offset = FARBWERK360_VIRTUAL_SENSORS_START;
- priv->buffer_size = FARBWERK360_CTRL_REPORT_SIZE;
priv->temp_ctrl_offset = FARBWERK360_TEMP_CTRL_OFFSET;
+
+ priv->buffer_size = FARBWERK360_CTRL_REPORT_SIZE;
+
priv->temp_label = label_temp_sensors;
priv->virtual_temp_label = label_virtual_temp_sensors;
break;
@@ -945,14 +966,17 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
priv->num_fans = OCTO_NUM_FANS;
priv->fan_sensor_offsets = octo_sensor_fan_offsets;
priv->fan_ctrl_offsets = octo_ctrl_fan_offsets;
+
priv->num_temp_sensors = OCTO_NUM_SENSORS;
priv->temp_sensor_start_offset = OCTO_SENSOR_START;
priv->num_virtual_temp_sensors = OCTO_NUM_VIRTUAL_SENSORS;
priv->virtual_temp_sensor_start_offset = OCTO_VIRTUAL_SENSORS_START;
- priv->power_cycle_count_offset = OCTO_POWER_CYCLES;
- priv->buffer_size = OCTO_CTRL_REPORT_SIZE;
priv->temp_ctrl_offset = OCTO_TEMP_CTRL_OFFSET;
+ priv->buffer_size = OCTO_CTRL_REPORT_SIZE;
+
+ priv->power_cycle_count_offset = OCTO_POWER_CYCLES;
+
priv->temp_label = label_temp_sensors;
priv->virtual_temp_label = label_virtual_temp_sensors;
priv->speed_label = label_fan_speed;
@@ -966,14 +990,17 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
priv->num_fans = QUADRO_NUM_FANS;
priv->fan_sensor_offsets = quadro_sensor_fan_offsets;
priv->fan_ctrl_offsets = quadro_ctrl_fan_offsets;
+
priv->num_temp_sensors = QUADRO_NUM_SENSORS;
priv->temp_sensor_start_offset = QUADRO_SENSOR_START;
priv->num_virtual_temp_sensors = QUADRO_NUM_VIRTUAL_SENSORS;
priv->virtual_temp_sensor_start_offset = QUADRO_VIRTUAL_SENSORS_START;
- priv->power_cycle_count_offset = QUADRO_POWER_CYCLES;
+ priv->temp_ctrl_offset = QUADRO_TEMP_CTRL_OFFSET;
+
priv->buffer_size = QUADRO_CTRL_REPORT_SIZE;
+
priv->flow_sensor_offset = QUADRO_FLOW_SENSOR_OFFSET;
- priv->temp_ctrl_offset = QUADRO_TEMP_CTRL_OFFSET;
+ priv->power_cycle_count_offset = QUADRO_POWER_CYCLES;
priv->temp_label = label_temp_sensors;
priv->virtual_temp_label = label_virtual_temp_sensors;
@@ -986,8 +1013,10 @@ static int aqc_probe(struct hid_device *hdev, const struct hid_device_id *id)
priv->kind = highflownext;
priv->num_fans = 0;
+
priv->num_temp_sensors = HIGHFLOWNEXT_NUM_SENSORS;
priv->temp_sensor_start_offset = HIGHFLOWNEXT_SENSOR_START;
+
priv->power_cycle_count_offset = QUADRO_POWER_CYCLES;
priv->temp_label = label_highflownext_temp_sensors;
--
2.38.1
On Mon, Nov 07, 2022 at 03:24:55PM +0100, Aleksa Savic wrote:
> Reorganize macro definitions into sections for each supported
> device, with additional comments on their purpose. This should
> make it easier to follow what report each offset is coming
> from. Also, reformat per-device initializations in
> aqc_probe() to organize them into sections (fan info,
> temp sensors, other parameters and lastly labels).
>
> No functional changes.
>
> Signed-off-by: Aleksa Savic <[email protected]>
Applied to hwmon-next.
Thanks,
Guenter