This patch series introduce nodes required for bringing remoteproc cores.
Adam Skladowski (3):
arm64: dts: MSM8953: Add wcnss nodes
arm64: dts: MSM8953: Add mpss nodes
arm64: dts: MSM8953: Add lpass nodes
arch/arm64/boot/dts/qcom/msm8953.dtsi | 358 ++++++++++++++++++++++++++
1 file changed, 358 insertions(+)
--
2.25.1
Add nodes for remoteproc, smp2p and smsm to make it possible to use
wifi/bt functionality on this platform.
Signed-off-by: Adam Skladowski <[email protected]>
---
arch/arm64/boot/dts/qcom/msm8953.dtsi | 130 ++++++++++++++++++++++++++
1 file changed, 130 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8953.dtsi b/arch/arm64/boot/dts/qcom/msm8953.dtsi
index 684668170353..df40584aafcf 100644
--- a/arch/arm64/boot/dts/qcom/msm8953.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8953.dtsi
@@ -326,6 +326,31 @@ rpmpd_opp_turbo: opp9 {
};
};
+ smp2p-wcnss {
+ compatible = "qcom,smp2p";
+ qcom,smem = <451>, <431>;
+
+ interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,ipc = <&apcs 8 18>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <4>;
+
+ smp2p_wcnss_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+
+ #qcom,smem-state-cells = <1>;
+ };
+
+ smp2p_wcnss_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
smsm {
compatible = "qcom,smsm";
@@ -340,6 +365,14 @@ apps_smsm: apps@0 {
#qcom,smem-state-cells = <1>;
};
+
+ wcnss_smsm: wcnss@6 {
+ reg = <6>;
+ interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
};
soc: soc@0 {
@@ -630,6 +663,37 @@ i2c_8_sleep: i2c-8-sleep-state {
drive-strength = <2>;
bias-disable;
};
+
+ wcnss_pin_a: wcnss-active-state {
+
+ wcss-wlan2-pins {
+ pins = "gpio76";
+ function = "wcss_wlan2";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+
+ wcss-wlan1-pins {
+ pins = "gpio77";
+ function = "wcss_wlan1";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+
+ wcss-wlan0-pins {
+ pins = "gpio78";
+ function = "wcss_wlan0";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+
+ wcss-wlan-pins {
+ pins = "gpio79", "gpio80";
+ function = "wcss_wlan";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+ };
};
gcc: clock-controller@1800000 {
@@ -1245,6 +1309,72 @@ i2c_8: i2c@7af8000 {
status = "disabled";
};
+ wcnss: remoteproc@a21b000 {
+ compatible = "qcom,pronto-v3-pil", "qcom,pronto";
+ reg = <0x0a204000 0x2000>, <0x0a202000 0x1000>, <0x0a21b000 0x3000>;
+ reg-names = "ccu", "dxe", "pmu";
+
+ memory-region = <&wcnss_fw_mem>;
+
+ interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_wcnss_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_wcnss_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_wcnss_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_wcnss_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+ power-domains = <&rpmpd MSM8953_VDDCX>,
+ <&rpmpd MSM8953_VDDMX>;
+ power-domain-names = "cx", "mx";
+
+ qcom,smem-states = <&smp2p_wcnss_out 0>;
+ qcom,smem-state-names = "stop";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&wcnss_pin_a>;
+
+ status = "disabled";
+
+ wcnss_iris: iris {
+ /* Separate chip, compatible is board-specific */
+ clocks = <&rpmcc RPM_SMD_RF_CLK2>;
+ clock-names = "xo";
+ };
+
+ smd-edge {
+ interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,ipc = <&apcs 8 17>;
+ qcom,smd-edge = <6>;
+ qcom,remote-pid = <4>;
+
+ label = "pronto";
+
+ wcnss_ctrl: wcnss {
+ compatible = "qcom,wcnss";
+ qcom,smd-channels = "WCNSS_CTRL";
+
+ qcom,mmio = <&wcnss>;
+
+ wcnss_bt: bluetooth {
+ compatible = "qcom,wcnss-bt";
+ };
+
+ wcnss_wifi: wifi {
+ compatible = "qcom,wcnss-wlan";
+
+ interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "tx", "rx";
+
+ qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
+ qcom,smem-state-names = "tx-enable",
+ "tx-rings-empty";
+ };
+ };
+ };
+ };
+
intc: interrupt-controller@b000000 {
compatible = "qcom,msm-qgic2";
interrupt-controller;
--
2.25.1
Add nodes for remoteproc, smp2p and smsm to make it possible to use
modem functionality on this platform.
Signed-off-by: Adam Skladowski <[email protected]>
---
arch/arm64/boot/dts/qcom/msm8953.dtsi | 87 +++++++++++++++++++++++++++
1 file changed, 87 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8953.dtsi b/arch/arm64/boot/dts/qcom/msm8953.dtsi
index df40584aafcf..257b1946372c 100644
--- a/arch/arm64/boot/dts/qcom/msm8953.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8953.dtsi
@@ -326,6 +326,31 @@ rpmpd_opp_turbo: opp9 {
};
};
+ smp2p-modem {
+ compatible = "qcom,smp2p";
+ qcom,smem = <435>, <428>;
+
+ interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,ipc = <&apcs 8 14>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <1>;
+
+ smp2p_modem_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+
+ #qcom,smem-state-cells = <1>;
+ };
+
+ smp2p_modem_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
smp2p-wcnss {
compatible = "qcom,smp2p";
qcom,smem = <451>, <431>;
@@ -366,6 +391,14 @@ apps_smsm: apps@0 {
#qcom,smem-state-cells = <1>;
};
+ modem_smsm: modem@1 {
+ reg = <1>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
wcnss_smsm: wcnss@6 {
reg = <6>;
interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>;
@@ -995,6 +1028,60 @@ spmi_bus: spmi@200f000 {
#size-cells = <0>;
};
+ mpss: remoteproc@4080000 {
+ compatible = "qcom,msm8953-mss-pil";
+ reg = <0x04080000 0x100>,
+ <0x04020000 0x040>;
+ reg-names = "qdsp6", "rmb";
+
+ interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_modem_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_modem_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_modem_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_modem_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+
+ power-domains = <&rpmpd MSM8953_VDDCX>,
+ <&rpmpd MSM8953_VDDMX>,
+ <&rpmpd MSM8953_VDDMD>;
+ power-domain-names = "cx", "mx","mss";
+
+ clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+ <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
+ <&gcc GCC_BOOT_ROM_AHB_CLK>,
+ <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "iface", "bus", "mem", "xo";
+
+ qcom,smem-states = <&smp2p_modem_out 0>;
+ qcom,smem-state-names = "stop";
+
+ resets = <&gcc GCC_MSS_BCR>;
+ reset-names = "mss_restart";
+
+ qcom,halt-regs = <&tcsr 0x18000 0x19000 0x1a000>;
+
+ status = "disabled";
+
+ mba {
+ memory-region = <&mba_mem>;
+ };
+
+ mpss {
+ memory-region = <&mpss_mem>;
+ };
+
+ smd-edge {
+ interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,smd-edge = <0>;
+ qcom,ipc = <&apcs 8 12>;
+ qcom,remote-pid = <1>;
+
+ label = "modem";
+ };
+ };
+
usb3: usb@70f8800 {
compatible = "qcom,msm8953-dwc3", "qcom,dwc3";
reg = <0x070f8800 0x400>;
--
2.25.1
Add nodes for remoteproc, smp2p and smsm in preparation
for audio support on this platform.
Signed-off-by: Adam Skladowski <[email protected]>
---
arch/arm64/boot/dts/qcom/msm8953.dtsi | 141 ++++++++++++++++++++++++++
1 file changed, 141 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8953.dtsi b/arch/arm64/boot/dts/qcom/msm8953.dtsi
index 257b1946372c..855595cbb09b 100644
--- a/arch/arm64/boot/dts/qcom/msm8953.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8953.dtsi
@@ -6,6 +6,9 @@
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,apr.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
#include <dt-bindings/thermal/thermal.h>
/ {
@@ -326,6 +329,30 @@ rpmpd_opp_turbo: opp9 {
};
};
+ smp2p-adsp {
+ compatible = "qcom,smp2p";
+ qcom,smem = <443>, <429>;
+
+ interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>;
+
+ mboxes = <&apcs 10>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <2>;
+
+ smp2p_adsp_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ smp2p_adsp_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
smp2p-modem {
compatible = "qcom,smp2p";
qcom,smem = <435>, <428>;
@@ -1532,6 +1559,120 @@ frame@b128000 {
status = "disabled";
};
};
+
+ lpass: remoteproc@c200000 {
+ compatible = "qcom,msm8953-adsp-pil";
+ reg = <0x0c200000 0x100>;
+
+ interrupts-extended = <&intc 0 293 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready",
+ "handover", "stop-ack";
+ clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>;
+ clock-names = "xo";
+
+ power-domains = <&rpmpd MSM8953_VDDCX>;
+ power-domain-names = "cx";
+
+ memory-region = <&adsp_fw_mem>;
+
+ qcom,smem-states = <&smp2p_adsp_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ smd-edge {
+ interrupts = <GIC_SPI 289 IRQ_TYPE_EDGE_RISING>;
+
+ label = "lpass";
+ mboxes = <&apcs 8>;
+ qcom,smd-edge = <1>;
+ qcom,remote-pid = <2>;
+
+ apr {
+ compatible = "qcom,apr-v2";
+ qcom,smd-channels = "apr_audio_svc";
+ qcom,apr-domain = <APR_DOMAIN_ADSP>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ q6core: service@3 {
+ reg = <APR_SVC_ADSP_CORE>;
+ compatible = "qcom,q6core";
+ };
+
+ q6afe: service@4 {
+ compatible = "qcom,q6afe";
+ reg = <APR_SVC_AFE>;
+ q6afedai: dais {
+ compatible = "qcom,q6afe-dais";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #sound-dai-cells = <1>;
+
+ dai@16 {
+ reg = <PRIMARY_MI2S_RX>;
+ qcom,sd-lines = <0 1>;
+ };
+ dai@20 {
+ reg = <TERTIARY_MI2S_TX>;
+ qcom,sd-lines = <0 1>;
+ };
+ dai@127 {
+ reg = <QUINARY_MI2S_RX>;
+ qcom,sd-lines = <0>;
+ };
+ };
+
+ q6afecc: clock-controller {
+ compatible = "qcom,q6afe-clocks";
+ #clock-cells = <2>;
+ };
+ };
+
+ q6asm: service@7 {
+ compatible = "qcom,q6asm";
+ reg = <APR_SVC_ASM>;
+ q6asmdai: dais {
+ compatible = "qcom,q6asm-dais";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #sound-dai-cells = <1>;
+
+ dai@0 {
+ reg = <0>;
+ direction = <Q6ASM_DAI_RX>;
+ };
+ dai@1 {
+ reg = <1>;
+ direction = <Q6ASM_DAI_TX>;
+ };
+ dai@2 {
+ reg = <2>;
+ direction = <Q6ASM_DAI_RX>;
+ };
+ dai@3 {
+ reg = <3>;
+ direction = <Q6ASM_DAI_RX>;
+ is-compress-dai;
+ };
+ };
+ };
+
+ q6adm: service@8 {
+ compatible = "qcom,q6adm";
+ reg = <APR_SVC_ADM>;
+ q6routing: routing {
+ compatible = "qcom,q6adm-routing";
+ #sound-dai-cells = <0>;
+ };
+ };
+ };
+ };
+ };
};
thermal-zones {
--
2.25.1
On Fri, 7 Apr 2023 18:53:41 +0200, Adam Skladowski wrote:
> This patch series introduce nodes required for bringing remoteproc cores.
>
> Adam Skladowski (3):
> arm64: dts: MSM8953: Add wcnss nodes
> arm64: dts: MSM8953: Add mpss nodes
> arm64: dts: MSM8953: Add lpass nodes
>
> [...]
Applied, thanks!
[1/3] arm64: dts: MSM8953: Add wcnss nodes
commit: b12428640ebeea3ee7e7ae817e1bd345612537df
[2/3] arm64: dts: MSM8953: Add mpss nodes
commit: 2bbada24e8a6c9eaf5caf015688dba0dcc3925d7
[3/3] arm64: dts: MSM8953: Add lpass nodes
commit: e58d100fa24309291ec500f9d161ff1ade20cabd
Best regards,
--
Bjorn Andersson <[email protected]>