This series adds support for:
- SERDES, WIZ DT nodes, Serdes lane control mux
- MAIN CPSW2G nodes
- DSS and DisplayPort-0 nodes
This series depends on DMA support patches for J784S4[1] which are
applied to linux-next.
DisplayPort has been tested on local J784S4 EVM. Test log:
<https://gist.github.com/Jayesh2000/49b11c0b62d5aecd14de1f7fd2bdca1f>
Changelog v3->v4:
- add reg property to serdes_ln_ctrl and fix the node name again to
get rid of dtbs_check error.
- reorder reg, reg-names and ranges property for main_cpsw1.
- correct the order for clocks in serdes_wiz nodes to fix dtbs_check
warnings.
- fix indentation in reg, reg-names and clock property for dss node.
- add comments for the reg type in dss registers.
Changelog v3->v2:
- fix dtc warnings for 'scm_conf' and 'serdes_ln_ctrl' nodes
(Checked all the changes of the series with W=12 option during build)
- added clock-frequency for serdes_refclk along with other EVM changes
This refclk is being used by all the instances of serdes_wiz which
are disabled by default. So configuring refclk when the serdes nodes
are used for the first time is okay.
Changelog v1->v2:
- Moved J784S4 EVM changes together to the last patch
(Suggested by Andrew)
v3 patch link:
<https://lore.kernel.org/all/[email protected]/>
[1]:
<https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=00e34c94987e4fe866f12ad8eac17268c936880c>
<https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=82e6051a48957a89066d15b17bb85d2f662f2bad>
<https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=436b288687176bf4d2c1cd25b86173e5a1649a60>
Rahul T R (2):
arm64: dts: ti: k3-j784s4-main: Add DSS and DP-bridge node
arm64: dts: ti: k3-j784s4-evm: Enable DisplayPort-0
Siddharth Vadapalli (3):
arm64: dts: ti: k3-j784s4-main: Add system controller and SERDES lane
mux
arm64: dts: ti: k3-j784s4: Add Main CPSW2G node
arm64: dts: ti: k3-j784s4: Add WIZ and SERDES PHY nodes
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 164 ++++++++++
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 335 +++++++++++++++++++++
2 files changed, 499 insertions(+)
--
2.25.1
From: Siddharth Vadapalli <[email protected]>
J784S4 SoC has 4 Serdes instances along with their respective WIZ
instances. Add device-tree nodes for them and disable them by default.
Signed-off-by: Siddharth Vadapalli <[email protected]>
[[email protected]: fix serdes_wiz clock order]
Signed-off-by: Jayesh Choudhary <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 171 +++++++++++++++++++++
1 file changed, 171 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
index b5f291eff1a3..9578c92a716a 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -7,6 +7,15 @@
#include <dt-bindings/mux/mux.h>
#include <dt-bindings/mux/ti-serdes.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/phy/phy-ti.h>
+
+/ {
+ serdes_refclk: serdes-refclk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ };
+};
&cbass_main {
msmc_ram: sram@70000000 {
@@ -441,6 +450,168 @@ main_sdhci1: mmc@4fb0000 {
status = "disabled";
};
+ serdes_wiz0: wiz@5060000 {
+ compatible = "ti,j784s4-wiz-10g";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ power-domains = <&k3_pds 404 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 404 2>, <&k3_clks 404 6>, <&serdes_refclk>, <&k3_clks 404 5>;
+ clock-names = "fck", "core_ref_clk", "ext_ref_clk", "core_ref1_clk";
+ assigned-clocks = <&k3_clks 404 6>;
+ assigned-clock-parents = <&k3_clks 404 10>;
+ num-lanes = <4>;
+ #reset-cells = <1>;
+ #clock-cells = <1>;
+ ranges = <0x5060000 0x00 0x5060000 0x10000>;
+
+ status = "disabled";
+
+ serdes0: serdes@5060000 {
+ compatible = "ti,j721e-serdes-10g";
+ reg = <0x05060000 0x010000>;
+ reg-names = "torrent_phy";
+ resets = <&serdes_wiz0 0>;
+ reset-names = "torrent_reset";
+ clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>,
+ <&serdes_wiz0 TI_WIZ_PHY_EN_REFCLK>;
+ clock-names = "refclk", "phy_en_refclk";
+ assigned-clocks = <&serdes_wiz0 TI_WIZ_PLL0_REFCLK>,
+ <&serdes_wiz0 TI_WIZ_PLL1_REFCLK>,
+ <&serdes_wiz0 TI_WIZ_REFCLK_DIG>;
+ assigned-clock-parents = <&k3_clks 404 6>,
+ <&k3_clks 404 6>,
+ <&k3_clks 404 6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <1>;
+
+ status = "disabled";
+ };
+ };
+
+ serdes_wiz1: wiz@5070000 {
+ compatible = "ti,j784s4-wiz-10g";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ power-domains = <&k3_pds 405 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 405 2>, <&k3_clks 405 6>, <&serdes_refclk>, <&k3_clks 405 5>;
+ clock-names = "fck", "core_ref_clk", "ext_ref_clk", "core_ref1_clk";
+ assigned-clocks = <&k3_clks 405 6>;
+ assigned-clock-parents = <&k3_clks 405 10>;
+ num-lanes = <4>;
+ #reset-cells = <1>;
+ #clock-cells = <1>;
+ ranges = <0x05070000 0x00 0x05070000 0x10000>;
+
+ status = "disabled";
+
+ serdes1: serdes@5070000 {
+ compatible = "ti,j721e-serdes-10g";
+ reg = <0x05070000 0x010000>;
+ reg-names = "torrent_phy";
+ resets = <&serdes_wiz1 0>;
+ reset-names = "torrent_reset";
+ clocks = <&serdes_wiz1 TI_WIZ_PLL0_REFCLK>,
+ <&serdes_wiz1 TI_WIZ_PHY_EN_REFCLK>;
+ clock-names = "refclk", "phy_en_refclk";
+ assigned-clocks = <&serdes_wiz1 TI_WIZ_PLL0_REFCLK>,
+ <&serdes_wiz1 TI_WIZ_PLL1_REFCLK>,
+ <&serdes_wiz1 TI_WIZ_REFCLK_DIG>;
+ assigned-clock-parents = <&k3_clks 405 6>,
+ <&k3_clks 405 6>,
+ <&k3_clks 405 6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <1>;
+
+ status = "disabled";
+ };
+ };
+
+ serdes_wiz2: wiz@5020000 {
+ compatible = "ti,j784s4-wiz-10g";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ power-domains = <&k3_pds 406 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 406 2>, <&k3_clks 406 6>, <&serdes_refclk>, <&k3_clks 406 5>;
+ clock-names = "fck", "core_ref_clk", "ext_ref_clk", "core_ref1_clk";
+ assigned-clocks = <&k3_clks 406 6>;
+ assigned-clock-parents = <&k3_clks 406 10>;
+ num-lanes = <4>;
+ #reset-cells = <1>;
+ #clock-cells = <1>;
+ ranges = <0x05020000 0x00 0x05020000 0x10000>;
+
+ status = "disabled";
+
+ serdes2: serdes@5020000 {
+ compatible = "ti,j721e-serdes-10g";
+ reg = <0x05020000 0x010000>;
+ reg-names = "torrent_phy";
+ resets = <&serdes_wiz2 0>;
+ reset-names = "torrent_reset";
+ clocks = <&serdes_wiz2 TI_WIZ_PLL0_REFCLK>,
+ <&serdes_wiz2 TI_WIZ_PHY_EN_REFCLK>;
+ clock-names = "refclk", "phy_en_refclk";
+ assigned-clocks = <&serdes_wiz2 TI_WIZ_PLL0_REFCLK>,
+ <&serdes_wiz2 TI_WIZ_PLL1_REFCLK>,
+ <&serdes_wiz2 TI_WIZ_REFCLK_DIG>;
+ assigned-clock-parents = <&k3_clks 406 6>,
+ <&k3_clks 406 6>,
+ <&k3_clks 406 6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <1>;
+
+ status = "disabled";
+ };
+ };
+
+ serdes_wiz4: wiz@5050000 {
+ compatible = "ti,j784s4-wiz-10g";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ power-domains = <&k3_pds 407 TI_SCI_PD_EXCLUSIVE>;
+ clocks = <&k3_clks 407 2>, <&k3_clks 407 6>, <&serdes_refclk>, <&k3_clks 407 5>;
+ clock-names = "fck", "core_ref_clk", "ext_ref_clk", "core_ref1_clk";
+ assigned-clocks = <&k3_clks 407 6>;
+ assigned-clock-parents = <&k3_clks 407 10>;
+ num-lanes = <4>;
+ #reset-cells = <1>;
+ #clock-cells = <1>;
+ ranges = <0x05050000 0x00 0x05050000 0x10000>,
+ <0xa030a00 0x00 0xa030a00 0x40>; /* DPTX PHY */
+
+ status = "disabled";
+
+ serdes4: serdes@5050000 {
+ /*
+ * Note: we also map DPTX PHY registers as the Torrent
+ * needs to manage those.
+ */
+ compatible = "ti,j721e-serdes-10g";
+ reg = <0x05050000 0x010000>,
+ <0x0a030a00 0x40>; /* DPTX PHY */
+ reg-names = "torrent_phy";
+ resets = <&serdes_wiz4 0>;
+ reset-names = "torrent_reset";
+ clocks = <&serdes_wiz4 TI_WIZ_PLL0_REFCLK>,
+ <&serdes_wiz4 TI_WIZ_PHY_EN_REFCLK>;
+ clock-names = "refclk", "phy_en_refclk";
+ assigned-clocks = <&serdes_wiz4 TI_WIZ_PLL0_REFCLK>,
+ <&serdes_wiz4 TI_WIZ_PLL1_REFCLK>,
+ <&serdes_wiz4 TI_WIZ_REFCLK_DIG>;
+ assigned-clock-parents = <&k3_clks 407 6>,
+ <&k3_clks 407 6>,
+ <&k3_clks 407 6>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #clock-cells = <1>;
+
+ status = "disabled";
+ };
+ };
+
main_navss: bus@30000000 {
compatible = "simple-bus";
#address-cells = <2>;
--
2.25.1
From: Siddharth Vadapalli <[email protected]>
The system controller node manages the CTRL_MMR0 region.
Add serdes_ln_ctrl node which is used for controlling the SERDES lane mux.
Signed-off-by: Siddharth Vadapalli <[email protected]>
[[email protected]: Add reg property to fix dtc warning]
Signed-off-by: Jayesh Choudhary <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 23 ++++++++++++++++++++++
1 file changed, 23 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
index e9169eb358c1..29be6d28ee31 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -5,6 +5,9 @@
* Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
*/
+#include <dt-bindings/mux/mux.h>
+#include <dt-bindings/mux/ti-serdes.h>
+
&cbass_main {
msmc_ram: sram@70000000 {
compatible = "mmio-sram";
@@ -26,6 +29,26 @@ l3cache-sram@200000 {
};
};
+ scm_conf: syscon@100000 {
+ compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+ reg = <0x00 0x00100000 0x00 0x1c000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0x00 0x00 0x00100000 0x1c000>;
+
+ serdes_ln_ctrl: mux-controller@4080 {
+ compatible = "mmio-mux";
+ reg = <0x00004080 0x30>;
+ #mux-control-cells = <1>;
+ mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
+ <0x4088 0x3>, <0x408c 0x3>, /* SERDES0 lane2/3 select */
+ <0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */
+ <0x4098 0x3>, <0x409c 0x3>, /* SERDES1 lane2/3 select */
+ <0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */
+ <0x40a8 0x3>, <0x40ac 0x3>; /* SERDES2 lane2/3 select */
+ };
+ };
+
gic500: interrupt-controller@1800000 {
compatible = "arm,gic-v3";
#address-cells = <2>;
--
2.25.1
From: Siddharth Vadapalli <[email protected]>
J784S4 SoC has a Main CPSW2G instance of the CPSW Ethernet Switch.
Add the device-tree nodes for the Main CPSW2G instance and enable it.
Signed-off-by: Siddharth Vadapalli <[email protected]>
[[email protected]: minor cleanups]
Signed-off-by: Jayesh Choudhary <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 48 +++++++++++++++
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 68 ++++++++++++++++++++++
2 files changed, 116 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index f33815953e77..aef6f53ae8ac 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -105,6 +105,30 @@ vdd_sd_dv: regulator-TLV71033 {
};
&main_pmx0 {
+ main_cpsw2g_pins_default: main-cpsw2g-pins-default {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x0b8, PIN_INPUT, 6) /* (AC34) MCASP1_ACLKX.RGMII1_RD0 */
+ J784S4_IOPAD(0x0a0, PIN_INPUT, 6) /* (AD34) MCASP0_AXR12.RGMII1_RD1 */
+ J784S4_IOPAD(0x0a4, PIN_INPUT, 6) /* (AJ36) MCASP0_AXR13.RGMII1_RD2 */
+ J784S4_IOPAD(0x0a8, PIN_INPUT, 6) /* (AF34) MCASP0_AXR14.RGMII1_RD3 */
+ J784S4_IOPAD(0x0b0, PIN_INPUT, 6) /* (AL33) MCASP1_AXR3.RGMII1_RXC */
+ J784S4_IOPAD(0x0ac, PIN_INPUT, 6) /* (AE34) MCASP0_AXR15.RGMII1_RX_CTL */
+ J784S4_IOPAD(0x08c, PIN_INPUT, 6) /* (AE35) MCASP0_AXR7.RGMII1_TD0 */
+ J784S4_IOPAD(0x090, PIN_INPUT, 6) /* (AC35) MCASP0_AXR8.RGMII1_TD1 */
+ J784S4_IOPAD(0x094, PIN_INPUT, 6) /* (AG35) MCASP0_AXR9.RGMII1_TD2 */
+ J784S4_IOPAD(0x098, PIN_INPUT, 6) /* (AH36) MCASP0_AXR10.RGMII1_TD3 */
+ J784S4_IOPAD(0x0b4, PIN_INPUT, 6) /* (AL34) MCASP1_AXR4.RGMII1_TXC */
+ J784S4_IOPAD(0x09c, PIN_INPUT, 6) /* (AF35) MCASP0_AXR11.RGMII1_TX_CTL */
+ >;
+ };
+
+ main_cpsw2g_mdio_pins_default: main-cpsw2g-mdio-pins-default {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x0c0, PIN_INPUT, 6) /* (AD38) MCASP1_AXR0.MDIO0_MDC */
+ J784S4_IOPAD(0x0bc, PIN_INPUT, 6) /* (AD33) MCASP1_AFSX.MDIO0_MDIO */
+ >;
+ };
+
main_uart8_pins_default: main-uart8-pins-default {
pinctrl-single,pins = <
J784S4_IOPAD(0x040, PIN_INPUT, 14) /* (AF37) MCASP0_AXR0.UART8_CTSn */
@@ -253,3 +277,27 @@ &mcu_cpsw_port1 {
phy-mode = "rgmii-rxid";
phy-handle = <&mcu_phy0>;
};
+
+&main_cpsw1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_cpsw2g_pins_default>;
+};
+
+&main_cpsw1_mdio {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_cpsw2g_mdio_pins_default>;
+
+ main_phy0: ethernet-phy@0 {
+ reg = <0>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+ ti,min-output-impedance;
+ };
+};
+
+&main_cpsw1_port1 {
+ status = "okay";
+ phy-mode = "rgmii-rxid";
+ phy-handle = <&main_phy0>;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
index 29be6d28ee31..b5f291eff1a3 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -36,6 +36,12 @@ scm_conf: syscon@100000 {
#size-cells = <1>;
ranges = <0x00 0x00 0x00100000 0x1c000>;
+ cpsw1_phy_gmii_sel: phy@4034 {
+ compatible = "ti,am654-phy-gmii-sel";
+ reg = <0x4034 0x4>;
+ #phy-cells = <1>;
+ };
+
serdes_ln_ctrl: mux-controller@4080 {
compatible = "mmio-mux";
reg = <0x00004080 0x30>;
@@ -778,6 +784,68 @@ cpts@310d0000 {
};
};
+ main_cpsw1: ethernet@c200000 {
+ compatible = "ti,j721e-cpsw-nuss";
+ reg = <0x00 0xc200000 0x00 0x200000>;
+ reg-names = "cpsw_nuss";
+ ranges = <0x00 0x00 0x00 0xc200000 0x00 0x200000>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ dma-coherent;
+ clocks = <&k3_clks 62 0>;
+ clock-names = "fck";
+ power-domains = <&k3_pds 62 TI_SCI_PD_EXCLUSIVE>;
+
+ dmas = <&main_udmap 0xc640>,
+ <&main_udmap 0xc641>,
+ <&main_udmap 0xc642>,
+ <&main_udmap 0xc643>,
+ <&main_udmap 0xc644>,
+ <&main_udmap 0xc645>,
+ <&main_udmap 0xc646>,
+ <&main_udmap 0xc647>,
+ <&main_udmap 0x4640>;
+ dma-names = "tx0", "tx1", "tx2", "tx3",
+ "tx4", "tx5", "tx6", "tx7",
+ "rx";
+
+ status = "disabled";
+
+ ethernet-ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ main_cpsw1_port1: port@1 {
+ reg = <1>;
+ label = "port1";
+ phys = <&cpsw1_phy_gmii_sel 1>;
+ ti,mac-only;
+ status = "disabled";
+ };
+ };
+
+ main_cpsw1_mdio: mdio@f00 {
+ compatible = "ti,cpsw-mdio", "ti,davinci_mdio";
+ reg = <0x00 0xf00 0x00 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&k3_clks 62 0>;
+ clock-names = "fck";
+ bus_freq = <1000000>;
+ };
+
+ cpts@3d000 {
+ compatible = "ti,am65-cpts";
+ reg = <0x00 0x3d000 0x00 0x400>;
+ clocks = <&k3_clks 62 3>;
+ clock-names = "cpts";
+ interrupts-extended = <&gic500 GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cpts";
+ ti,cpts-ext-ts-inputs = <4>;
+ ti,cpts-periodic-outputs = <2>;
+ };
+ };
+
main_mcan0: can@2701000 {
compatible = "bosch,m_can";
reg = <0x00 0x02701000 0x00 0x200>,
--
2.25.1
From: Rahul T R <[email protected]>
Enable display for J784S4 EVM.
Add assigned clocks for DSS, DT node for DisplayPort PHY and pinmux for
DP HPD. Add the clock frequency for serdes_refclk.
Add the endpoint nodes to describe connection from:
DSS => MHDP => DisplayPort connector.
Also add the GPIO expander-4 node and pinmux for main_i2c4 which is
required for controlling DP power. Set status for all required nodes
for DP-0 as "okay".
Signed-off-by: Rahul T R <[email protected]>
[[email protected]: move all the changes together to enable DP-0 in EVM]
Signed-off-by: Jayesh Choudhary <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 116 +++++++++++++++++++++++
1 file changed, 116 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index aef6f53ae8ac..03c9bf34cb1b 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -102,6 +102,28 @@ vdd_sd_dv: regulator-TLV71033 {
states = <1800000 0x0>,
<3300000 0x1>;
};
+
+ dp0_pwr_3v3: regulator-dp0-prw {
+ compatible = "regulator-fixed";
+ regulator-name = "dp0-pwr";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&exp4 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ dp0: dp0-connector {
+ compatible = "dp-connector";
+ label = "DP0";
+ type = "full-size";
+ dp-pwr-supply = <&dp0_pwr_3v3>;
+
+ port {
+ dp0_connector_in: endpoint {
+ remote-endpoint = <&dp0_out>;
+ };
+ };
+ };
};
&main_pmx0 {
@@ -163,6 +185,19 @@ vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
J784S4_IOPAD(0x020, PIN_INPUT, 7) /* (AJ35) MCAN15_RX.GPIO0_8 */
>;
};
+
+ dp0_pins_default: dp0-pins-default {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x0cc, PIN_INPUT, 12) /* (AM37) SPI0_CS0.DP0_HPD */
+ >;
+ };
+
+ main_i2c4_pins_default: main-i2c4-pins-default {
+ pinctrl-single,pins = <
+ J784S4_IOPAD(0x014, PIN_INPUT_PULLUP, 8) /* (AG33) MCAN14_TX.I2C4_SCL */
+ J784S4_IOPAD(0x010, PIN_INPUT_PULLUP, 8) /* (AH33) MCAN13_RX.I2C4_SDA */
+ >;
+ };
};
&wkup_pmx0 {
@@ -301,3 +336,84 @@ &main_cpsw1_port1 {
phy-mode = "rgmii-rxid";
phy-handle = <&main_phy0>;
};
+
+&serdes_refclk {
+ clock-frequency = <100000000>;
+};
+
+&dss {
+ status = "okay";
+ assigned-clocks = <&k3_clks 218 2>,
+ <&k3_clks 218 5>,
+ <&k3_clks 218 14>,
+ <&k3_clks 218 18>;
+ assigned-clock-parents = <&k3_clks 218 3>,
+ <&k3_clks 218 7>,
+ <&k3_clks 218 16>,
+ <&k3_clks 218 22>;
+};
+
+&serdes_wiz4 {
+ status = "okay";
+};
+
+&serdes4 {
+ status = "okay";
+ serdes4_dp_link: phy@0 {
+ reg = <0>;
+ cdns,num-lanes = <4>;
+ #phy-cells = <0>;
+ cdns,phy-type = <PHY_TYPE_DP>;
+ resets = <&serdes_wiz4 1>, <&serdes_wiz4 2>,
+ <&serdes_wiz4 3>, <&serdes_wiz4 4>;
+ };
+};
+
+&mhdp {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&dp0_pins_default>;
+ phys = <&serdes4_dp_link>;
+ phy-names = "dpphy";
+};
+
+&dss_ports {
+ port {
+ dpi0_out: endpoint {
+ remote-endpoint = <&dp0_in>;
+ };
+ };
+};
+
+&main_i2c4 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c4_pins_default>;
+ clock-frequency = <400000>;
+
+ exp4: gpio@20 {
+ compatible = "ti,tca6408";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&dp0_ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ dp0_in: endpoint {
+ remote-endpoint = <&dpi0_out>;
+ };
+ };
+
+ port@4 {
+ reg = <4>;
+ dp0_out: endpoint {
+ remote-endpoint = <&dp0_connector_in>;
+ };
+ };
+};
--
2.25.1
From: Rahul T R <[email protected]>
Add DSS and DP-bridge node for J784S4 SoC. DSS IP in J784S4 is
same as DSS IP in J721E, so same compatible is being used.
The DP is Cadence MHDP8546.
Signed-off-by: Rahul T R <[email protected]>
[[email protected]: move dss & mhdp node together in main, fix dss node]
Signed-off-by: Jayesh Choudhary <[email protected]>
---
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 73 ++++++++++++++++++++++
1 file changed, 73 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
index 9578c92a716a..fc3ffb252fa4 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -1374,4 +1374,77 @@ main_spi7: spi@2170000 {
clocks = <&k3_clks 383 1>;
status = "disabled";
};
+
+ mhdp: dp-bridge@a000000 {
+ compatible = "ti,j721e-mhdp8546";
+
+ reg = <0x0 0xa000000 0x0 0x30a00>,
+ <0x0 0x4f40000 0x0 0x20>;
+ reg-names = "mhdptx", "j721e-intg";
+
+ clocks = <&k3_clks 217 11>;
+
+ interrupt-parent = <&gic500>;
+ interrupts = <GIC_SPI 614 IRQ_TYPE_LEVEL_HIGH>;
+
+ power-domains = <&k3_pds 217 TI_SCI_PD_EXCLUSIVE>;
+
+ status = "disabled";
+
+ dp0_ports: ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ dss: dss@4a00000 {
+ compatible = "ti,j721e-dss";
+ reg = <0x00 0x04a00000 0x00 0x10000>, /* common_m */
+ <0x00 0x04a10000 0x00 0x10000>, /* common_s0*/
+ <0x00 0x04b00000 0x00 0x10000>, /* common_s1*/
+ <0x00 0x04b10000 0x00 0x10000>, /* common_s2*/
+ <0x00 0x04a20000 0x00 0x10000>, /* vidl1 */
+ <0x00 0x04a30000 0x00 0x10000>, /* vidl2 */
+ <0x00 0x04a50000 0x00 0x10000>, /* vid1 */
+ <0x00 0x04a60000 0x00 0x10000>, /* vid2 */
+ <0x00 0x04a70000 0x00 0x10000>, /* ovr1 */
+ <0x00 0x04a90000 0x00 0x10000>, /* ovr2 */
+ <0x00 0x04ab0000 0x00 0x10000>, /* ovr3 */
+ <0x00 0x04ad0000 0x00 0x10000>, /* ovr4 */
+ <0x00 0x04a80000 0x00 0x10000>, /* vp1 */
+ <0x00 0x04aa0000 0x00 0x10000>, /* vp1 */
+ <0x00 0x04ac0000 0x00 0x10000>, /* vp1 */
+ <0x00 0x04ae0000 0x00 0x10000>, /* vp4 */
+ <0x00 0x04af0000 0x00 0x10000>; /* wb */
+
+ reg-names = "common_m", "common_s0",
+ "common_s1", "common_s2",
+ "vidl1", "vidl2","vid1","vid2",
+ "ovr1", "ovr2", "ovr3", "ovr4",
+ "vp1", "vp2", "vp3", "vp4",
+ "wb";
+
+ clocks = <&k3_clks 218 0>,
+ <&k3_clks 218 2>,
+ <&k3_clks 218 5>,
+ <&k3_clks 218 14>,
+ <&k3_clks 218 18>;
+ clock-names = "fck", "vp1", "vp2", "vp3", "vp4";
+
+ power-domains = <&k3_pds 218 TI_SCI_PD_EXCLUSIVE>;
+
+ interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "common_m",
+ "common_s0",
+ "common_s1",
+ "common_s2";
+
+ status = "disabled";
+
+ dss_ports: ports {
+ };
+ };
};
--
2.25.1
Hi,
On 4/25/2023 6:46 PM, Jayesh Choudhary wrote:
> From: Siddharth Vadapalli <[email protected]>
>
> The system controller node manages the CTRL_MMR0 region.
> Add serdes_ln_ctrl node which is used for controlling the SERDES lane mux.
>
> Signed-off-by: Siddharth Vadapalli <[email protected]>
> [[email protected]: Add reg property to fix dtc warning]
> Signed-off-by: Jayesh Choudhary <[email protected]>
> ---
> arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 23 ++++++++++++++++++++++
> 1 file changed, 23 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> index e9169eb358c1..29be6d28ee31 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> @@ -5,6 +5,9 @@
> * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
> */
>
> +#include <dt-bindings/mux/mux.h>
> +#include <dt-bindings/mux/ti-serdes.h>
> +
> &cbass_main {
> msmc_ram: sram@70000000 {
> compatible = "mmio-sram";
> @@ -26,6 +29,26 @@ l3cache-sram@200000 {
> };
> };
>
> + scm_conf: syscon@100000 {
Please check syscon address.
Thanks,
Achal Verma
> + compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
> + reg = <0x00 0x00100000 0x00 0x1c000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x00 0x00 0x00100000 0x1c000>;
> +
> + serdes_ln_ctrl: mux-controller@4080 {
> + compatible = "mmio-mux";
> + reg = <0x00004080 0x30>;
> + #mux-control-cells = <1>;
> + mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
> + <0x4088 0x3>, <0x408c 0x3>, /* SERDES0 lane2/3 select */
> + <0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */
> + <0x4098 0x3>, <0x409c 0x3>, /* SERDES1 lane2/3 select */
> + <0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */
> + <0x40a8 0x3>, <0x40ac 0x3>; /* SERDES2 lane2/3 select */
> + };
> + };
> +
> gic500: interrupt-controller@1800000 {
> compatible = "arm,gic-v3";
> #address-cells = <2>;
Achal,
On 15/05/23 11:25, Verma, Achal wrote:
> Hi,
>
> On 4/25/2023 6:46 PM, Jayesh Choudhary wrote:
>> From: Siddharth Vadapalli <[email protected]>
>>
>> The system controller node manages the CTRL_MMR0 region.
>> Add serdes_ln_ctrl node which is used for controlling the SERDES lane mux.
>>
>> Signed-off-by: Siddharth Vadapalli <[email protected]>
>> [[email protected]: Add reg property to fix dtc warning]
>> Signed-off-by: Jayesh Choudhary <[email protected]>
>> ---
>> arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 23 ++++++++++++++++++++++
>> 1 file changed, 23 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
>> b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
>> index e9169eb358c1..29be6d28ee31 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
>> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
>> @@ -5,6 +5,9 @@
>> * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
>> */
>> +#include <dt-bindings/mux/mux.h>
>> +#include <dt-bindings/mux/ti-serdes.h>
>> +
>> &cbass_main {
>> msmc_ram: sram@70000000 {
>> compatible = "mmio-sram";
>> @@ -26,6 +29,26 @@ l3cache-sram@200000 {
>> };
>> };
>> + scm_conf: syscon@100000 {
> Please check syscon address.
0x100000 is the base address of the CTRL_MMR module. Could you please clarify
why the address is incorrect? The registers for J784S4 SoC can be viewed at:
https://www.ti.com/lit/zip/spruj52
>
> Thanks,
> Achal Verma
>> + compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
>> + reg = <0x00 0x00100000 0x00 0x1c000>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0x00 0x00 0x00100000 0x1c000>;
>> +
>> + serdes_ln_ctrl: mux-controller@4080 {
>> + compatible = "mmio-mux";
>> + reg = <0x00004080 0x30>;
>> + #mux-control-cells = <1>;
>> + mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1
>> select */
>> + <0x4088 0x3>, <0x408c 0x3>, /* SERDES0 lane2/3 select */
>> + <0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */
>> + <0x4098 0x3>, <0x409c 0x3>, /* SERDES1 lane2/3 select */
>> + <0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */
>> + <0x40a8 0x3>, <0x40ac 0x3>; /* SERDES2 lane2/3 select */
>> + };
>> + };
>> +
>> gic500: interrupt-controller@1800000 {
>> compatible = "arm,gic-v3";
>> #address-cells = <2>;
--
Regards,
Siddharth.
On 5/15/2023 1:06 PM, Siddharth Vadapalli wrote:
> Achal,
>
> On 15/05/23 11:25, Verma, Achal wrote:
>> Hi,
>>
>> On 4/25/2023 6:46 PM, Jayesh Choudhary wrote:
>>> From: Siddharth Vadapalli <[email protected]>
>>>
>>> The system controller node manages the CTRL_MMR0 region.
>>> Add serdes_ln_ctrl node which is used for controlling the SERDES lane mux.
>>>
>>> Signed-off-by: Siddharth Vadapalli <[email protected]>
>>> [[email protected]: Add reg property to fix dtc warning]
>>> Signed-off-by: Jayesh Choudhary <[email protected]>
>>> ---
>>> arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 23 ++++++++++++++++++++++
>>> 1 file changed, 23 insertions(+)
>>>
>>> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
>>> b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
>>> index e9169eb358c1..29be6d28ee31 100644
>>> --- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
>>> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
>>> @@ -5,6 +5,9 @@
>>> * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
>>> */
>>> +#include <dt-bindings/mux/mux.h>
>>> +#include <dt-bindings/mux/ti-serdes.h>
>>> +
>>> &cbass_main {
>>> msmc_ram: sram@70000000 {
>>> compatible = "mmio-sram";
>>> @@ -26,6 +29,26 @@ l3cache-sram@200000 {
>>> };
>>> };
>>> + scm_conf: syscon@100000 {
>> Please check syscon address.
>
> 0x100000 is the base address of the CTRL_MMR module. Could you please clarify
> why the address is incorrect? The registers for J784S4 SoC can be viewed at:
> https://www.ti.com/lit/zip/spruj52
I got the doubt because of the address used in this [1] series was
different. Now I realized that it was wrong and it got corrected in this
patch. So yeah its clear now, 0x100000 is indeed the correct base address.
[1]
https://serenity.dal.design.ti.com/patchwork/project/linux-patch-review/patch/[email protected]/
>
>>
>> Thanks,
>> Achal Verma
>>> + compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
>>> + reg = <0x00 0x00100000 0x00 0x1c000>;
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + ranges = <0x00 0x00 0x00100000 0x1c000>;
>>> +
>>> + serdes_ln_ctrl: mux-controller@4080 {
>>> + compatible = "mmio-mux";
>>> + reg = <0x00004080 0x30>;
>>> + #mux-control-cells = <1>;
>>> + mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1
>>> select */
>>> + <0x4088 0x3>, <0x408c 0x3>, /* SERDES0 lane2/3 select */
>>> + <0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */
>>> + <0x4098 0x3>, <0x409c 0x3>, /* SERDES1 lane2/3 select */
>>> + <0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */
>>> + <0x40a8 0x3>, <0x40ac 0x3>; /* SERDES2 lane2/3 select */
>>> + };
>>> + };
>>> +
>>> gic500: interrupt-controller@1800000 {
>>> compatible = "arm,gic-v3";
>>> #address-cells = <2>;
>