The ExpressWire protocol is shared between at least KTD2692 and KTD2801
with slight differences such as timings and the former not having a
defined set of pulses for enabling the protocol (possibly because it
does not support PWM unlike KTD2801). Despite these differences the
ExpressWire handling code can be shared between the two, so in
preparation for adding KTD2801 support introduce a library implementing
this protocol.
Suggested-by: Daniel Thompson <[email protected]>
Reviewed-by: Linus Walleij <[email protected]>
Reviewed-by: Daniel Thompson <[email protected]>
Signed-off-by: Duje Mihanović <[email protected]>
---
MAINTAINERS | 7 +++++
drivers/leds/Kconfig | 4 +++
drivers/leds/Makefile | 3 ++
drivers/leds/leds-expresswire.c | 68 ++++++++++++++++++++++++++++++++++++++++
include/linux/leds-expresswire.h | 36 +++++++++++++++++++++
5 files changed, 118 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 8d1052fa6a69..e1c83e0e837a 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -7979,6 +7979,13 @@ S: Maintained
T: git git://git.kernel.org/pub/scm/linux/kernel/git/linkinjeon/exfat.git
F: fs/exfat/
+EXPRESSWIRE PROTOCOL LIBRARY
+M: Duje Mihanović <[email protected]>
+L: [email protected]
+S: Maintained
+F: drivers/leds/leds-expresswire.c
+F: include/linux/leds-expresswire.h
+
EXT2 FILE SYSTEM
M: Jan Kara <[email protected]>
L: [email protected]
diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
index d721b254e1e4..64bb2de237e9 100644
--- a/drivers/leds/Kconfig
+++ b/drivers/leds/Kconfig
@@ -186,6 +186,10 @@ config LEDS_EL15203000
To compile this driver as a module, choose M here: the module
will be called leds-el15203000.
+config LEDS_EXPRESSWIRE
+ bool
+ depends on GPIOLIB
+
config LEDS_TURRIS_OMNIA
tristate "LED support for CZ.NIC's Turris Omnia"
depends on LEDS_CLASS_MULTICOLOR
diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
index ce07dc295ff0..effdfc6f1e95 100644
--- a/drivers/leds/Makefile
+++ b/drivers/leds/Makefile
@@ -91,6 +91,9 @@ obj-$(CONFIG_LEDS_WM831X_STATUS) += leds-wm831x-status.o
obj-$(CONFIG_LEDS_WM8350) += leds-wm8350.o
obj-$(CONFIG_LEDS_WRAP) += leds-wrap.o
+# Kinetic ExpressWire Protocol
+obj-$(CONFIG_LEDS_EXPRESSWIRE) += leds-expresswire.o
+
# LED SPI Drivers
obj-$(CONFIG_LEDS_CR0014114) += leds-cr0014114.o
obj-$(CONFIG_LEDS_DAC124S085) += leds-dac124s085.o
diff --git a/drivers/leds/leds-expresswire.c b/drivers/leds/leds-expresswire.c
new file mode 100644
index 000000000000..89e147b0e019
--- /dev/null
+++ b/drivers/leds/leds-expresswire.c
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Shared library for Kinetic's ExpressWire protocol.
+ * This protocol works by pulsing the ExpressWire IC's control GPIO.
+ * ktd2692 and ktd2801 are known to use this protocol.
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio/consumer.h>
+#include <linux/leds-expresswire.h>
+
+void expresswire_power_off(struct expresswire_common_props *props)
+{
+ gpiod_set_value_cansleep(props->ctrl_gpio, 0);
+ usleep_range(props->timing.poweroff_us, props->timing.poweroff_us * 2);
+}
+EXPORT_SYMBOL_NS_GPL(expresswire_power_off, EXPRESSWIRE);
+
+void expresswire_enable(struct expresswire_common_props *props)
+{
+ gpiod_set_value(props->ctrl_gpio, 1);
+ udelay(props->timing.detect_delay_us);
+ gpiod_set_value(props->ctrl_gpio, 0);
+ udelay(props->timing.detect_us);
+ gpiod_set_value(props->ctrl_gpio, 1);
+}
+EXPORT_SYMBOL_NS_GPL(expresswire_enable, EXPRESSWIRE);
+
+void expresswire_start(struct expresswire_common_props *props)
+{
+ gpiod_set_value(props->ctrl_gpio, 1);
+ udelay(props->timing.data_start_us);
+}
+EXPORT_SYMBOL_NS_GPL(expresswire_start, EXPRESSWIRE);
+
+void expresswire_end(struct expresswire_common_props *props)
+{
+ gpiod_set_value(props->ctrl_gpio, 0);
+ udelay(props->timing.end_of_data_low_us);
+ gpiod_set_value(props->ctrl_gpio, 1);
+ udelay(props->timing.end_of_data_high_us);
+}
+EXPORT_SYMBOL_NS_GPL(expresswire_end, EXPRESSWIRE);
+
+void expresswire_set_bit(struct expresswire_common_props *props, bool bit)
+{
+ if (bit) {
+ gpiod_set_value(props->ctrl_gpio, 0);
+ udelay(props->timing.short_bitset_us);
+ gpiod_set_value(props->ctrl_gpio, 1);
+ udelay(props->timing.long_bitset_us);
+ } else {
+ gpiod_set_value(props->ctrl_gpio, 0);
+ udelay(props->timing.long_bitset_us);
+ gpiod_set_value(props->ctrl_gpio, 1);
+ udelay(props->timing.short_bitset_us);
+ }
+}
+EXPORT_SYMBOL_NS_GPL(expresswire_set_bit, EXPRESSWIRE);
+
+void expresswire_write_u8(struct expresswire_common_props *props, u8 val)
+{
+ expresswire_start(props);
+ for (int i = 7; i >= 0; i--)
+ expresswire_set_bit(props, val & BIT(i));
+ expresswire_end(props);
+}
+EXPORT_SYMBOL_NS_GPL(expresswire_write_u8, EXPRESSWIRE);
diff --git a/include/linux/leds-expresswire.h b/include/linux/leds-expresswire.h
new file mode 100644
index 000000000000..3c61902ccac8
--- /dev/null
+++ b/include/linux/leds-expresswire.h
@@ -0,0 +1,36 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Shared library for Kinetic's ExpressWire protocol.
+ * This protocol works by pulsing the ExpressWire IC's control GPIO.
+ * ktd2692 and ktd2801 are known to use this protocol.
+ */
+
+#ifndef _LEDS_EXPRESSWIRE_H
+#define _LEDS_EXPRESSWIRE_H
+
+#include <linux/gpio/consumer.h>
+
+struct expresswire_timing {
+ unsigned long poweroff_us;
+ unsigned long detect_delay_us;
+ unsigned long detect_us;
+ unsigned long data_start_us;
+ unsigned long end_of_data_low_us;
+ unsigned long end_of_data_high_us;
+ unsigned long short_bitset_us;
+ unsigned long long_bitset_us;
+};
+
+struct expresswire_common_props {
+ struct gpio_desc *ctrl_gpio;
+ struct expresswire_timing timing;
+};
+
+void expresswire_power_off(struct expresswire_common_props *props);
+void expresswire_enable(struct expresswire_common_props *props);
+void expresswire_start(struct expresswire_common_props *props);
+void expresswire_end(struct expresswire_common_props *props);
+void expresswire_set_bit(struct expresswire_common_props *props, bool bit);
+void expresswire_write_u8(struct expresswire_common_props *props, u8 val);
+
+#endif /* _LEDS_EXPRESSWIRE_H */
--
2.43.0