2017-11-08 18:16 GMT+08:00 Arnd Bergmann <[email protected]>:
> On Wed, Nov 8, 2017 at 6:55 AM, Greentime Hu <[email protected]> wrote:
>
>> diff --git a/arch/nds32/Kconfig b/arch/nds32/Kconfig
>> new file mode 100644
>> index 0000000..112f470
>> --- /dev/null
>> +++ b/arch/nds32/Kconfig
>> @@ -0,0 +1,107 @@
>> +#
>> +# For a description of the syntax of this configuration file,
>> +# see Documentation/kbuild/kconfig-language.txt.
>> +#
>> +
>> +config NDS32
>> + def_bool y
>> + select ARCH_HAS_RAW_COPY_USER
>> + select ARCH_WANT_FRAME_POINTERS if FTRACE
>> + select ARCH_WANT_IPC_PARSE_VERSION
>> + select CLKSRC_MMIO
>> + select CLONE_BACKWARDS
>> + select TIMER_OF
>> + select FRAME_POINTER
>> + select GENERIC_ATOMIC64
>> + select GENERIC_CPU_DEVICES
>> + select GENERIC_CLOCKEVENTS
>> + select GENERIC_IOMAP
>> + select GENERIC_IRQ_CHIP
>> + select GENERIC_IRQ_PROBE
>> + select GENERIC_IRQ_SHOW
>> + select GENERIC_STRNCPY_FROM_USER
>> + select GENERIC_STRNLEN_USER
>> + select GENERIC_TIME_VSYSCALL
>> + select HAVE_ARCH_TRACEHOOK
>> + select HAVE_GENERIC_IOMAP
>
> You normally don't want HAVE_GENERIC_IOMAP, at least unless the CPU
> has special instructions to trigger PCI I/O port access.
Thanks.
I will remove it in the next version patch.
>> + select HAVE_DEBUG_KMEMLEAK
>> + select HAVE_IDE
>
> You certainly don't want HAVE_IDE
Thanks.
I will remove it in the next version patch.
>> + select HAVE_MEMBLOCK
>> + select HAVE_MEMBLOCK_NODE_MAP
>> + select HAVE_UID16
>
> HAVE_UID16 shouldn't be used on new architectures, as mentioned in the
> comment about asm/posix_types.h
Thanks.
I will remove it in the next version patch.
>> + select HAVE_REGS_AND_STACK_ACCESS_API
>> + select IRQ_DOMAIN
>> + select LOCKDEP_SUPPORT
>> + select MODULES_USE_ELF_REL
>> + select MODULES_USE_ELF_RELA
>
> I would think that you use either MODULES_USE_ELF_REL or
> MODULES_USE_ELF_RELA, but not both.
Thanks.
I will check which one we used and remove the other one if posible.
>> + select OF
>> + select OF_EARLY_FLATTREE
>> + select OLD_SIGACTION
>> + select OLD_SIGSUSPEND3
>
> What are the OLD_SIG* ones for? It sounds like something you shouldn't
> need, although I'm not familiar wiht them.
Thanks I will check if we need it or not.
>> + select NO_IOPORT_MAP
>> + select RTC_LIB
>> + select THREAD_INFO_IN_TASK
>> + select SYS_SUPPORTS_APM_EMULATION
>
> I don't see what SYS_SUPPORTS_APM_EMULATION gains you.
Thanks.
I will remove it in the next version patch.
>> +config GENERIC_CALIBRATE_DELAY
>> + def_bool y
>
> It's better to avoid the delay loop completely and skip the calibration,
> if your hardware allows.
Thanks.
Do you mean that this config should be def_bool n?
why? Almost all arch enable it.
>> +
>> +config NDS32_BUILTIN_DTB
>> + string "Builtin DTB"
>> + default ""
>> + help
>> + User can use it to specify the dts of the SoC
>
> Better leave this up to the boot loader.
Thanks.
uboot will pass it too.
>> +config ALIGNMENT_TRAP
>> + tristate "Kernel support unaligned access handling"
>> + default y
>> + help
>> + Andes processors cannot fetch/store information which is not
>> + naturally aligned on the bus, i.e., a 4 byte fetch must start at an
>> + address divisible by 4. On 32-bit Andes processors, these non-aligned
>> + fetch/store instructions will be emulated in software if you say
>> + here, which has a severe performance impact. This is necessary for
>> + correct operation of some network protocols. With an IP-only
>> + configuration it is safe to say N, otherwise say Y.
>
> Which network protocols are you referring to?
I will modify these descriptions. It was written by someone I don't know. :p
This case only happened when I found is compiler code gen issue or
wrong pointer usage.
>> +config HIGHMEM
>> + bool "High Memory Support"
>> + depends on MMU && CPU_CACHE_NONALIASING
>> + help
>> + The address space of Andes processors is only 4 Gigabytes large
>> + and it has to accommodate user address space, kernel address
>> + space as well as some memory mapped IO. That means that, if you
>> + have a large amount of physical memory and/or IO, not all of the
>> + memory can be "permanently mapped" by the kernel. The physical
>> + memory that is not permanently mapped is called "high memory".
>> +
>> + Depending on the selected kernel/user memory split, minimum
>> + vmalloc space and actual amount of RAM, you may not need this
>> + option which should result in a slightly faster kernel.
>> +
>> + If unsure, say N.
>
> Generally speaking, highmem support is a mess, and it's better to avoid it.
>
> I see that the two device tree files you have list 1GB of memory. Do you think
> that is a common configuration for actual products? Do you expect any to
> have more than 1GB (or more than 4GB) in the future, or is that the upper
> end of the scale?
>
> If 1GB is a reasonable upper bound, then you could change the vmsplit
> to give slightly less address space to user space and have 1GB of direct-mapped
> kernel memory plus 256MB of vmalloc space reserved for the kernel,
> and completely avoid highmem.
Thanks.
We do realy use 1GB ram in some products.
We also verify CONFIG_HIGHMEM with LTP too.
It seems fine but I will study vmsplit to see if we should use it.
>> +config MEMORY_START
>> + hex "Physical memory start address"
>> + default "0x00000000"
>> + help
>> + Physical memory start address, you may modify it if it is porting to
>> + a new SoC with different start address.
>> +endmenu
>
> On ARM, we found options like this to be rather problematic since it prevents
> you from running the same kernel on boards that are otherwise compatible.
>
> If the architecture easily allows the memory to start at address 0, could
> you require this address for all SoCs that want to run Linux, and get
> rid of the compile-time option?
Thanks.
The reason we need this config is because we need to define PHYS_OFFSET.
#define PHYS_OFFSET (CONFIG_MEMORY_START)
It needs to be set in compile-time. I don't know how to get rid of it.
From 1583492631960091032@xxx Wed Nov 08 10:17:33 +0000 2017
X-GM-THRID: 1583483358934427114
X-Gmail-Labels: Inbox,Category Forums,HistoricalUnread