Hello,
I got shiny new Sony-ericsson W760i mobile phone. When I plug it into the USB
through USB cable, I got the following messages:
[526453.604104] usb usb2: usb resume
[526453.604110] ehci_hcd 0000:00:1a.7: resume root hub
[526453.667408] hub 2-0:1.0: hub_resume
[526453.667433] ehci_hcd 0000:00:1a.7: GetStatus port 3 status 001803 POWER
sig=j CSC CONNECT
[526453.667436] hub 2-0:1.0: port 3: status 0501 change 0001
[526453.667447] hub 2-0:1.0: port 4: status 0507 change 0000
[526453.770777] hub 2-0:1.0: state 7 ports 4 chg 0008 evt 0000
[526453.770791] hub 2-0:1.0: port 3, status 0501, change 0000, 480 Mb/s
[526453.825770] ehci_hcd 0000:00:1a.7: port 3 high speed
[526453.825773] ehci_hcd 0000:00:1a.7: GetStatus port 3 status 001005 POWER
sig=se0 PE CONNECT
[526453.877448] usb 2-3: new high speed USB device using ehci_hcd and address
11
[526454.101020] ehci_hcd 0000:00:1a.7: port 3 high speed
[526454.101025] ehci_hcd 0000:00:1a.7: GetStatus port 3 status 001005 POWER
sig=se0 PE CONNECT
[526454.174558] usb 2-3: default language 0x0409
[526454.175059] usb 2-3: uevent
[526454.175076] usb 2-3: usb_probe_device
[526454.175077] usb 2-3: configuration #2 chosen from 1 choice
[526454.175650] usb 2-3: adding 2-3:2.0 (config #2, interface 0)
[526454.175664] usb 2-3:2.0: uevent
[526454.175678] libusual 2-3:2.0: usb_probe_interface
[526454.175682] libusual 2-3:2.0: usb_probe_interface - got id
[526454.175693] usb-storage 2-3:2.0: usb_probe_interface
[526454.175697] usb-storage 2-3:2.0: usb_probe_interface - got id
[526454.178273] scsi9 : SCSI emulation for USB Mass Storage devices
[526454.178526] usb-storage: device found at 11
[526454.178528] usb-storage: waiting for device to settle before scanning
[526454.179019] drivers/usb/core/inode.c: creating file '011'
[526454.179058] usb 2-3: New USB device found, idVendor=0fce, idProduct=e0c6
[526454.179060] usb 2-3: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
[526454.179062] usb 2-3: Product: Memory Stick
[526454.179064] usb 2-3: Manufacturer: Sony Ericsson
[526454.179065] usb 2-3: SerialNumber: 3570670220504780
[526459.177824] usb-storage: device scan complete
[526459.178328] scsi 9:0:0:0: Direct-Access Sony Eri Memory Stick
0 PQ: 0 ANSI: 0
[526459.178690] scsi 9:0:0:1: Direct-Access Sony Eri Memory Stick
0 PQ: 0 ANSI: 0
[526459.179532] sd 9:0:0:0: [sdb] 120093 512-byte hardware sectors: (61.4
MB/58.6 MiB)
[526459.180534] sd 9:0:0:0: [sdb] Test WP failed, assume Write Enabled
[526459.180536] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[526459.182285] sd 9:0:0:0: [sdb] 120093 512-byte hardware sectors: (61.4
MB/58.6 MiB)
[526459.183280] sd 9:0:0:0: [sdb] Test WP failed, assume Write Enabled
[526459.183283] sd 9:0:0:0: [sdb] Assuming drive cache: write through
[526459.183286] sdb: sdb1
[526459.186089] sd 9:0:0:0: [sdb] Attached SCSI removable disk
[526459.186239] sd 9:0:0:0: Attached scsi generic sg2 type 0
[526459.186908] sd 9:0:0:1: [sdc] 3995648 512-byte hardware sectors: (2.04
GB/1.90 GiB)
[526459.247211] sd 9:0:0:1: [sdc] Test WP failed, assume Write Enabled
[526459.247216] sd 9:0:0:1: [sdc] Assuming drive cache: write through
[526459.264317] sd 9:0:0:1: [sdc] 3995648 512-byte hardware sectors: (2.04
GB/1.90 GiB)
[526459.266565] sd 9:0:0:1: [sdc] Test WP failed, assume Write Enabled
[526459.266567] sd 9:0:0:1: [sdc] Assuming drive cache: write through
[526459.266571] sdc:<7>ehci_hcd 0000:00:1a.7: port 3 high speed
[526489.341028] ehci_hcd 0000:00:1a.7: GetStatus port 3 status 001005 POWER
sig=se0 PE CONNECT
[526489.392244] usb 2-3: reset high speed USB device using ehci_hcd and
address 11
[526489.452275] ehci_hcd 0000:00:1a.7: port 3 high speed
[526489.452283] ehci_hcd 0000:00:1a.7: GetStatus port 3 status 001005 POWER
sig=se0 PE CONNECT
[526520.349404] ehci_hcd 0000:00:1a.7: port 3 high speed
[526520.349408] ehci_hcd 0000:00:1a.7: GetStatus port 3 status 001005 POWER
sig=se0 PE CONNECT
[526520.401598] usb 2-3: reset high speed USB device using ehci_hcd and
address 11
[526520.467654] ehci_hcd 0000:00:1a.7: port 3 high speed
[526520.467665] ehci_hcd 0000:00:1a.7: GetStatus port 3 status 001005 POWER
sig=se0 PE CONNECT
and the devices /dev/sdc* and /dev/sdb* disappears. Is there something I could
do for get it working? It works with Windows. This test was on 2.6.28 but it
is not better on 2.6.24 or 2.6.26.
--
Luk?? Hejtm?nek