s/folowing/following/
s/Celsuis/Celsius/
s/temerature/temperature/ ...twice
Signed-off-by: Bhaskar Chowdhury <[email protected]>
---
drivers/net/wireless/intel/iwlwifi/fw/api/power.h | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/net/wireless/intel/iwlwifi/fw/api/power.h b/drivers/net/wireless/intel/iwlwifi/fw/api/power.h
index 798417182d54..f7c7852127d3 100644
--- a/drivers/net/wireless/intel/iwlwifi/fw/api/power.h
+++ b/drivers/net/wireless/intel/iwlwifi/fw/api/power.h
@@ -54,7 +54,7 @@ struct iwl_ltr_config_cmd_v1 {
* @flags: See &enum iwl_ltr_config_flags
* @static_long: static LTR Long register value.
* @static_short: static LTR Short register value.
- * @ltr_cfg_values: LTR parameters table values (in usec) in folowing order:
+ * @ltr_cfg_values: LTR parameters table values (in usec) in following order:
* TX, RX, Short Idle, Long Idle. Used only if %LTR_CFG_FLAG_UPDATE_VALUES
* is set.
* @ltr_short_idle_timeout: LTR Short Idle timeout (in usec). Used only if
@@ -493,7 +493,7 @@ union iwl_ppag_table_cmd {
* Roaming Energy Delta Threshold, otherwise use normal Energy Delta
* Threshold. Typical energy threshold is -72dBm.
* @bf_temp_threshold: This threshold determines the type of temperature
- * filtering (Slow or Fast) that is selected (Units are in Celsuis):
+ * filtering (Slow or Fast) that is selected (Units are in Celsius):
* If the current temperature is above this threshold - Fast filter
* will be used, If the current temperature is below this threshold -
* Slow filter will be used.
@@ -501,12 +501,12 @@ union iwl_ppag_table_cmd {
* calculated for this and the last passed beacon is greater than this
* threshold. Zero value means that the temperature change is ignored for
* beacon filtering; beacons will not be forced to be sent to driver
- * regardless of whether its temerature has been changed.
+ * regardless of whether its temperature has been changed.
* @bf_temp_slow_filter: Send Beacon to driver if delta in temperature values
* calculated for this and the last passed beacon is greater than this
* threshold. Zero value means that the temperature change is ignored for
* beacon filtering; beacons will not be forced to be sent to driver
- * regardless of whether its temerature has been changed.
+ * regardless of whether its temperature has been changed.
* @bf_enable_beacon_filter: 1, beacon filtering is enabled; 0, disabled.
* @bf_debug_flag: beacon filtering debug configuration
* @bf_escape_timer: Send beacons to to driver if no beacons were passed
--
2.30.2
On 3/16/21 9:25 PM, Bhaskar Chowdhury wrote:
>
> s/folowing/following/
> s/Celsuis/Celsius/
> s/temerature/temperature/ ...twice
>
>
> Signed-off-by: Bhaskar Chowdhury <[email protected]>
Acked-by: Randy Dunlap <[email protected]>
> ---
> drivers/net/wireless/intel/iwlwifi/fw/api/power.h | 8 ++++----
> 1 file changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/net/wireless/intel/iwlwifi/fw/api/power.h b/drivers/net/wireless/intel/iwlwifi/fw/api/power.h
> index 798417182d54..f7c7852127d3 100644
> --- a/drivers/net/wireless/intel/iwlwifi/fw/api/power.h
> +++ b/drivers/net/wireless/intel/iwlwifi/fw/api/power.h
> @@ -54,7 +54,7 @@ struct iwl_ltr_config_cmd_v1 {
> * @flags: See &enum iwl_ltr_config_flags
> * @static_long: static LTR Long register value.
> * @static_short: static LTR Short register value.
> - * @ltr_cfg_values: LTR parameters table values (in usec) in folowing order:
> + * @ltr_cfg_values: LTR parameters table values (in usec) in following order:
> * TX, RX, Short Idle, Long Idle. Used only if %LTR_CFG_FLAG_UPDATE_VALUES
> * is set.
> * @ltr_short_idle_timeout: LTR Short Idle timeout (in usec). Used only if
> @@ -493,7 +493,7 @@ union iwl_ppag_table_cmd {
> * Roaming Energy Delta Threshold, otherwise use normal Energy Delta
> * Threshold. Typical energy threshold is -72dBm.
> * @bf_temp_threshold: This threshold determines the type of temperature
> - * filtering (Slow or Fast) that is selected (Units are in Celsuis):
> + * filtering (Slow or Fast) that is selected (Units are in Celsius):
> * If the current temperature is above this threshold - Fast filter
> * will be used, If the current temperature is below this threshold -
> * Slow filter will be used.
> @@ -501,12 +501,12 @@ union iwl_ppag_table_cmd {
> * calculated for this and the last passed beacon is greater than this
> * threshold. Zero value means that the temperature change is ignored for
> * beacon filtering; beacons will not be forced to be sent to driver
> - * regardless of whether its temerature has been changed.
> + * regardless of whether its temperature has been changed.
> * @bf_temp_slow_filter: Send Beacon to driver if delta in temperature values
> * calculated for this and the last passed beacon is greater than this
> * threshold. Zero value means that the temperature change is ignored for
> * beacon filtering; beacons will not be forced to be sent to driver
> - * regardless of whether its temerature has been changed.
> + * regardless of whether its temperature has been changed.
> * @bf_enable_beacon_filter: 1, beacon filtering is enabled; 0, disabled.
> * @bf_debug_flag: beacon filtering debug configuration
> * @bf_escape_timer: Send beacons to to driver if no beacons were passed
> --
--
~Randy