2021-09-21 01:38:02

by Jérôme Pouiller

[permalink] [raw]
Subject: [PATCH v7 02/24] dt-bindings: introduce silabs,wfx.yaml

From: Jérôme Pouiller <[email protected]>

Prepare the inclusion of the wfx driver in the kernel.

Signed-off-by: Jérôme Pouiller <[email protected]>
---
.../bindings/net/wireless/silabs,wfx.yaml | 133 ++++++++++++++++++
1 file changed, 133 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml

diff --git a/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml
new file mode 100644
index 000000000000..8a249ada45dd
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml
@@ -0,0 +1,133 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (c) 2020, Silicon Laboratories, Inc.
+%YAML 1.2
+---
+
+$id: http://devicetree.org/schemas/net/wireless/silabs,wfx.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Silicon Labs WFxxx devicetree bindings
+
+maintainers:
+ - Jérôme Pouiller <[email protected]>
+
+description: >
+ Support for the Wifi chip WFxxx from Silicon Labs. Currently, the only device
+ from the WFxxx series is the WF200 described here:
+ https://www.silabs.com/documents/public/data-sheets/wf200-datasheet.pdf
+
+ The WF200 can be connected via SPI or via SDIO.
+
+ For SDIO:
+
+ Declaring the WFxxx chip in device tree is mandatory (usually, the VID/PID is
+ sufficient for the SDIO devices).
+
+ It is recommended to declare a mmc-pwrseq on SDIO host above WFx. Without
+ it, you may encounter issues during reboot. The mmc-pwrseq should be
+ compatible with mmc-pwrseq-simple. Please consult
+ Documentation/devicetree/bindings/mmc/mmc-pwrseq-simple.yaml for more
+ information.
+
+ For SPI:
+
+ In add of the properties below, please consult
+ Documentation/devicetree/bindings/spi/spi-controller.yaml for optional SPI
+ related properties.
+
+properties:
+ compatible:
+ const: silabs,wf200
+
+ reg:
+ description:
+ When used on SDIO bus, <reg> must be set to 1. When used on SPI bus, it is
+ the chip select address of the device as defined in the SPI devices
+ bindings.
+ maxItems: 1
+
+ spi-max-frequency: true
+
+ interrupts:
+ description: The interrupt line. Triggers IRQ_TYPE_LEVEL_HIGH and
+ IRQ_TYPE_EDGE_RISING are both supported by the chip and the driver. When
+ SPI is used, this property is required. When SDIO is used, the "in-band"
+ interrupt provided by the SDIO bus is used unless an interrupt is defined
+ in the Device Tree.
+ maxItems: 1
+
+ reset-gpios:
+ description: (SPI only) Phandle of gpio that will be used to reset chip
+ during probe. Without this property, you may encounter issues with warm
+ boot. (For legacy purpose, the gpio in inverted when compatible ==
+ "silabs,wfx-spi")
+
+ For SDIO, the reset gpio should declared using a mmc-pwrseq.
+ maxItems: 1
+
+ wakeup-gpios:
+ description: Phandle of gpio that will be used to wake-up chip. Without this
+ property, driver will disable most of power saving features.
+ maxItems: 1
+
+ silabs,antenna-config-file:
+ $ref: /schemas/types.yaml#/definitions/string
+ description: Use an alternative file for antenna configuration (aka
+ "Platform Data Set" in Silabs jargon). Default is 'wf200.pds'.
+
+ local-mac-address: true
+
+ mac-address: true
+
+additionalProperties: false
+
+required:
+ - compatible
+ - reg
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ spi0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wifi@0 {
+ compatible = "silabs,wf200";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wfx_irq &wfx_gpios>;
+ reg = <0>;
+ interrupts-extended = <&gpio 16 IRQ_TYPE_EDGE_RISING>;
+ wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ spi-max-frequency = <42000000>;
+ };
+ };
+
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ wfx_pwrseq: wfx_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wfx_reset>;
+ reset-gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
+ };
+
+ mmc0 {
+ mmc-pwrseq = <&wfx_pwrseq>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ wifi@1 {
+ compatible = "silabs,wf200";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wfx_wakeup>;
+ reg = <1>;
+ wakeup-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>;
+ };
+ };
+...
--
2.33.0


2021-09-23 17:12:18

by Rob Herring

[permalink] [raw]
Subject: Re: [PATCH v7 02/24] dt-bindings: introduce silabs,wfx.yaml

On Mon, 20 Sep 2021 18:11:14 +0200, Jerome Pouiller wrote:
> From: J?r?me Pouiller <[email protected]>
>
> Prepare the inclusion of the wfx driver in the kernel.
>
> Signed-off-by: J?r?me Pouiller <[email protected]>
> ---
> .../bindings/net/wireless/silabs,wfx.yaml | 133 ++++++++++++++++++
> 1 file changed, 133 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/net/wireless/silabs,wfx.yaml
>

Reviewed-by: Rob Herring <[email protected]>